E1-2260-2025-4-ERODE CITY MUNICIPAL CORPORATION

Amount

Labour charges for dismantling of old Plain Cement Concrete including all labour and convinience charges etc complete

Plain cement Concrete 1:4:8 (One cement,Four crushed stone sand and Eight hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers

Brick work in following Cement Mortar using best quality II class table moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 20mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Labour charges for replacement of gas burner, gas tube, regulator, and gas valve including all labour and conveyance charges etc complete as directed by departmental officers

Repairing of idly cooker including replacement of following spares: 1) 5 nos of inner box for idly cooker with SS 304 sheet including SS sheet cutting, bending and SS welding including spot welding 2) Box complete welding with spot welding 3) Idly box full polishing 4) Bolt and nuts 5) New inlet pipe line 6) Rope for inlet pipe line 7) Door rubber 8) Steam pipe line SS valve rope 9) Main cork set 10) Steam control valves 11) Dismantling and re fixing

Repairing of boiler including replacement of following spares and labour charges for erection and dismantling: 1) Inner drum plate 2) Burners 3) Packing rope 4) Bolt nuts 5) Outer drum welding 6) Outer casing 7) Outlet pipe line 8) Mild steel union 9) Cutting, welding lathe and conveyance charges

Repairing of grinder machine including worn out spare parts: 1) Rewinding of 3 phase motor coil 2) Oil seal 3) Bearing 4) Motor bearing 5) Bolt nuts 6) Total service and labour charges

Charges for repairing of electronic weighing scale with replacement of following spares: 1) Load cell 2) Battery

Repairing of pulverizer machine including required spare parts: 1) Machine Plate 2) Oil seal 3) Bearing 4) Motor bearing 5) Bolt nuts 6) Bottom MS angle stand 7) Total service and labour charges

Supply and delivery of Aluminium and Stainless steel vessels with following specifications:

Aluminium Vana of thickness 16 kg thickness

Aluminium 16 kg thickness lid for aluminium vana

Stainless steel Anda of thickness 22kg

Commercial mixie of capacity 1300W

Stainless steel 9 litre Ex weld bucket

Aluminium 16 kg thickness idly paanai of capacity 120 idlies

Stainless steel plate for tiffin

Stainless steel Jug

BALAGURU INFRA (BID ID -1476612)