Internal electrification of Armory Extension,New Shoping centre and electrical renovation in various toilets and Labs. at RRCAT, Indore.

Amount

Power Distribution Boards : Supply, Installation, testing and commissioning of Prefabricated wall mounted electrical DB's.

PDB : Suitable for TP and SP both type of outgoings. Any configuration in outgoing MCB's shall be required during installation either TP or SP or combination. IP shall be 42/43. (a). I/C : 125A,25KA, Thermal Release, TP+neutral link, MCCB....1 no.(B)Outgoings : 8 WAY/Phase(C) 16 to 32A TP/SP, C curve, 10 KA MCB ...…6/18Nos. (d)63A TP, C curve, 10 KA MCB ...…2Nos.(e) Neutral link and Earthing Link shall be provided.

LDB: (a) Incomer : 40/50/63A TPN/FP,10KA MCB.1 no.(b)Outgoings : 6 WAY per phase. (b) 6to 32 A SP, C curve MCB ...… 18Nos.(c) Neutral link and Earthig Link shall be provided.

SPNDB: With acrylic/tranparent door - (a) Incomer : 32A, DP MCB 10KA…...1 no.(b)Outgoings : 12Way.(c) 6to 32 A SP/DP, C curve MCB ...… 10/5Nos.(d) Neutral link and Earthig Link shall be provided.

G.I Earthing : Supply, Installation, testing and commissioning of GI plate earthing as per IS: 3043 and our specifications. The size of the plate will be 600X600X6.3mm. A test link of size 200mm length and 5mm thick shall be provided inside of earthing chamber. Two length of GI strip of size 50X5mm shall be installed from GI plate to test link. This GI strip shall be welded minimum 300mm both side in centre of plate and connected with test link by suitable NUT-BOLTS with washers. At both end of test link there shall be provision of NUT-BOLT and washer for connection of GI strip which is connecting the earth pits with the system or quipments. A 19mm dia GI pipe shall be install from mid of GI plate to earthing chamber and funnel will be mounted on the top of this pipe. There shall be hole of all along the GI pipe and it should be cut at 45 degree angle at the plate side end. CI pre-casted cover shall be provided on the earthing chamber. The chamber of earthing pit shall be as per attached sketch.

Supply and Installation of 50X5/6,32X6/ 25X5/25X3mm size GI earth strip or GI wire of various sizes.

Supply,pulling,testing and commissioning of 0.5mm ATC twin pair telephone wire through concealed/surface conduits including end termination.

Supply and Installation of ERW MS concealed/Surface conduit system, with bare Copper wire one length along the conduit and upto termination point with termination. If required conduit installed for fire shall be painted or marked by red color.All required fittings and accessories will be supplied and fixed as per IS of following sizes:

25mm. MS conduit with single length bare copper conductor of 16SWG shall be wraped all around the conduit and will be terminated properly for earth continuity.

Supply,pulling and end connection of 1100V voltage grade FRLS PVC insulated, multi strand flexible copper wires in following size.:

Supply, Installation,testing and commissioning of CAT-6 cable with termination at both end i.e. outlet and Racks. All the materials required to complete the work will be supplied by the contractor.

Power outlets/Switch Boards : Supply,Installation,testing and commissioning of following :

40/50/63A, TPN/FP C curve, 10KA MCB + prefabricated Metal enclousure.

40/50/63A, DP C curve, 10KA MCB + prefabricated Metal enclousure.

2X16/25/32A, DP C curve, 10KA MCB + Readymade Metal enclousure.

32A, FP C curve, 10KA MCB + Readymade Metal enclousure.

1 nos.,6A, 250V SPT/ two way/Bell push premium quality modular Switch +box+plate with fixing and mounting accessories.

1 nos.,6A, 250V 5 Pin Shutter type premium quality modular Socket+box+plate and other fixing and mounting accessories.

1 nos.,16/6A, 250V 5 Pin, Shutter type Switch-Socket with Indicator premium quality modular type. +box+plate and other fixing and mounting accessories.

RJ-11 telephone outlet with box and plate.

Network outlet RJ45 with box and plate.RJ45 shall be compatible with speed of CAT-6 cable.

Ceiling rose/angle or batten holder/nipple/blank plate and other accessories reuired to make a point or mount luminaires.

Supply cutting and fixing of 3/5mm thick Phenolic Laminated sheet with hardware. Sizes will be as per site requirements.

Fabrication Supply and Installation of MS sheet,strips and ISA etc.

Supply,installation,testing and commissioning of power cables of following sizes :

On wall/trench/above false ceiling - 4CX 70sq.mm. Al. Ar. cable.

On wall/trench/above false ceiling - 4CX 16 sq.mm. Al. Ar. cable.

Laid Under ground - 4CX 16 sq.mm. Al. Ar. cable.

End Jointing : Supply,installation,testing and commissioning of cable end joints of following size cables:

4 CX70sq.mm. Al. Ar. cable. End joint shall be done by Double compression gland.

4 CX 16 sq.mm. Al. Ar. cable. End joint shall be done by Double compression gland.

Supply,Installation,testing and commissioning of various types of fans with supply of 3 core double insulated cable, connector and plug top with all required fixing materials. Down rod shall be in the scope of item with sizes from 300 to 800mm as per site requirements.

1200mm sweep BLDC five star rated ceiling fan with step type electronic regulator of same make.Two module electronic fan regulator with speed control in steps and steps shall be marked+MS box and plate.

450mm wall mounted fan

300mm exhaust fan with wall cawl and bird screen.

200mm ventination fan

Supply,Installation,testing and commissioning of following luminaires :

Indoor decorative 2'X2' surface/recess mounted, high efficiency LED luminaire with CRCA poweder coated housing with nominal efficacy >100 lumen/watt and nominal output as 4000 lumen, CCT - 6500K, Pf-0.9 (min), THD <10%, CRI>80, optics high quality diffuser complete with all accessories, driver and all required fixing accessories and hardware etc.

Indoor decorative surface/recess mounted, round/square LED type aluminium die cast housing meeting the following specifications - nominal efficacy >100 lumen/watt and nominal output as 1600 lumen, CCT - 6500K, Pf-0.9 (min), THDI <10%, CRI>80, optics high quality polycorbonate diffuser complete with all accessories, driver and all required fixing accessories and hardware etc.

Outdoor type surface mounted LED Bulkhead luminaire having nominal lumen output 700 lumen and nominal efficacy as 100 lm/watt, CCT 6500K, Pf- 0.9 (min), THDi <10%, CRI>80 with all accessories, driver and all required fixinf accessories and hardware etc.

LED Mirror Light.

1X36Watt automated UV-C disinfection system(ADS) unit with humen presence sensor and programmable operation cycle including all accessories.

Fabrication, Supply and installation of Pole suitable to mount on RCC foundation/MS railling. Pole shall be painted with two coat of red oxide and synthetic paints or hot dipped galvanised octagonal. Drawing of pole shall be approved before fabrication. Supply,installation,fixing of 12W, efficacy >100 lm/watt and nominal output shall be 1200 lumen, CCT- 6500K, CRI>80, THDI <10%, LED street light. Weatherproof termination boxes shall be provided in case requirements.

Supply,installation,testing and commissioning of MS round pipe of 70 mm dia., 1.6 mtr. height with ms arm for mounting of luminaires.The supply of street light LED Luminaires having nominal lumen output 1000 lumen and nominal efficacy as 100 lm/W, CCT 4000K, Pf-0.9 (min), THDI <10%, CRI>70 with all accessories, driver and all required fixing accessories and hardware etc. This pole shall be mounted on MS railing and making arrangement to mount it on MS railing with LED luminaires is in the scope of the item.

Supply, installation, testing and commissioning of 5 meter hot dipped galvanised octagonal pole with foundation templete-bolts and LED luminaires having nominal lumen output 1000 lumen and nominal efficacy as 100 lm/watt,CCT 4000K, Pf-0.9 (min), THDI <10%, CRI>70 with all accessories, driver and all required fixing accessories and hardware etc. This pole shall be mounted on MS railing and making arrangement to mount it on MS railing with LED luminaires is in the scope of the item.

Supply installation testing and commissioning of cable management system with following items -

100X50mm PVC body with cover and partition.

End cap

90 degree angle

Partition Junction internal/external

Cover and body joint

Cable clip

RAJESH GAWDE

P.B.ELECTRICALS

DYNAMIC ENGINEERS AND CONTRACTORS