ADDITION ALTERATION RENOVATION OF CE R AND D BUILDING P 50 UNDER GE I R AND D DELHI

Amount

B/R (Portion) Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish including tiles outside MoD land complete all as specified and directed .

Roughening surfaces of old concrete /terrazzo flooring by picking, sweeping clean and washing down with water to remove dust complete all as specified and directed .

M&L for laying Vitrified Ceramic tiles (light shade) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, first quality coloured of grade B II (a) /B II (b) and of abrasion reistance PE-I-III or above etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15 mm thick screed bed in CM (1:4) complete all as specified and directed .

M&L for providing Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm first quality coloured of grade B II (a) /B II (b) and of abrasion reistance PE-I-III or above, for work on vertical surfaces such as skirting / dado etc. set and jointed in neat cement slurry and pointed in colour cement to match tile over and including 10 mm thick rendering in CM (1:3) complete all as specified and directed .

M&L for laying Vitrified Ceramic tiles double charged (dark shade) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm first quality coloured of grade B II (a) /B II (b) and of abrasion reistance PE-I-III or above, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match tile over and including fixed with chemicals as per Manufacturer's instructions complete all as specified and directed .

M&L for laying anti skid ceramic tiles 8mm thick coloured design (square /rectagular) area of each tile exc 0.11 sqm but n exc 0.18 sqm first quality coloured of grade B 11(a) /B 11(b) and of abrasion reistance PE-I-III or above in floors set jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15mm thick screed bed of CM (1:6) complete all as specified and directed .

M&L for providing Glazed coloured design ceramic tiles 450X 300X 7mm thick super glossy 1st quality of grade B tiles on vertical surfaces such as skirting /dado etc set and jointed in neat cement slurry and pointed in colour cement to match tiles over and including 10 mm thick screed in CM (1:3) complete all as specified and directed .

M&L for providing Glazed coloured design ceramic tiles 400X 800X 7mm thick super glossy 1st quality of grade B tiles on vertical surfaces such as skirting /dado etc set and jointed in neat cement slurry and pointed in colour cement to match tiles over and including 10 mm thick screed in CM (1:3) complete all as specified and directed.

M&L for 25 mm thick Plain cement concrete (PCC) (1:2:4), type B0 (using 12.5mm graded stone aggregate) as in sub floors and sub base floors to receive floor topping, complete all as specified and directed .

Demolition of plain cement Concrete of any description and in any position not otherwise specifically provided for and including removal of debris and rubbish out side defence land complete all as specified and directed.

M&L for 16 to 18 mm thick machine cut kota stone slab of size 550mmx550mm laid as in flooring, tread / landing laid over and including 15 mm thick screed bed or bedding layer in CM (1:4), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including necessay grinding, rubbing, rounding to exposed edges with moulding and polishing in granite finish complete all as specfied and directed.

M&L for providing machine cut kota stone slab 16-18mm thick as in skirting,risers of steps laid over and including 10 mm thick rendering in CM (1:3), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including necessay grinding, rubbing, rounding to exposed edges with moulding and polishing in granite finish complete all as specfied and directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons skirting etc laid bedded and pointed in any mortar and including removal from the out side defence land with mortar complete all as specified and directed

M&L for laying 16 to 18 mm thick machine cut mirror polished granite stone slab prefect black as in shelves , counter for wash hand basin , floor and window cill etc bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade / matrix of granite stone including grinding, moulding & polishing and bevelling half round edges of stones laid over and including 15 mm thick screed bed in CM (1:4) complete all as specified and directed

M&L for providing 16 to 18 mm thick machine cut mirror polished granite stone slab perfect black on vertical surfaces such as skirting/dado, window sides etc set and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, moulding & polishing and bevelling half round edges of stones fixed over and including rendering 10 mm thick in CM (1:3) complete all as specified and directed

M&L for laying rubber/PVC moulded coulured designer chequered tiles of size 300 x 300 x 25mm texture series in floor etc bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade / matrix of tiles laid over over and including 15 mm thick sereed bed in CM (1:4) complete all as specified and directed.

Taking down steel/wooden chowkhats or frames (without taking off woodenshutters from the frame) n.exc 1.5 sqm each complete all as specified and directed

Taking down chowkats or frames or partitions( (without taking off shutters from the frames) exc 1.5 Sqm but n exc 4 Sqm complete all as specified and directed Notes : The grills /guard bars with frame shall be distmantled under item 41 here-in-after of BOQ.

Taking down chowkats or frames of any description or aluminium partition (without taking off shutters from the frames) exc 4 Sqm but n exc 10 Sqm each complete all as specified and as directed . Notes for Ser item No 17 to 19 :- Rate also included in this items for necessary cutting doors/taking out hold fast from the existing concrete /brick work and making good the disturbed surfaces with match existing surfaces after erecting new frames /chowkhats/partitions.

S&F Pressed steel frames for doors made out of 1.25mm thick MS Sheet of size 125 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, all as specified, and directed. Notes :- PCC filling to frame shall be measured & paid separately under respective item of BOQ.

S&F Pressed steel frames for doors made out of 1.25mm thick MS Sheet of size 105 x 60mm with one rebate including necessary fixing lugs, hinges, lock strike plate, etc., complete, all as specified, and directed. Notes :- PCC filling to frame shall be measured & paid separately under respective item of BOQ.

M&L for PCC (1:3:6) type C1 using (20 mm graded stone aggregate) as filling in sunken floor and steel frames complete all as specified and directed

S&F 40 mm thick factory made flush shutter, confirming to IS 2002(Part-I) solid core construction with block board core and ply wood face panels, commercial type on both sides with teak wood lipping 6mm thick and 40mm wide all around to the shutter complete all as specsified & directed.

M&L for fiber glass reinforced plastic (FRP) door frame three legged off cross section 90mmx45mm having single rebate of 32mm x 15mm to receive shutter of 30mm thickness, moulded with fire retardent grade unsaturated polyster resin and chopped mat. Frame laminated with 2mm thick and filled with suitalbe wooden block in all three legs, covered with fibre glass from all sides. MS stay provided at the bottom of steady the frame and confirming to IS provided at the bottom of standing the frame and confirming to IS 14856-2000 complete all as specified and directed.

M&L for FRP door shutter shall be 30mm thick glass fibre reinforced plastic (FRP) panelled door shutter of coloured and made with fire retardent grade unsaturated polyster resin moulded to 3 mm thick FRP laminate for forming hollow rails and styles with wooden frame and suitable blocks of seasoned wood inside at required placess for fixing of fittings, cast monolithically with 5 mm thick FRP panels and confirming to IS 14856-2000 complete all as specified and directed.

S&F stainless steel barrel tower bolts, size 150mm and dia of shoot / bolts not less than 10mm of AISI 316 grade complete all as specified and directed

S&F stainless steel handle, size 150mm of AISI 316 grade complete all as specified and directed

S&F stainless steel butt hinges, size 100mm of AISI 316 grade complete all as specified and directed

S&F stainless steel sliding door bolts with hasp, staple of size 250mm long and dia of shoot not less than 12mm of AISI 316 grade complete all as specified and directed

M&L for 1.5mm thick decorative laminate type 1, of surface finish, colour and pattern as approved, fixed with adhesive as per manufacturers instructions complete all as specified and as directed.

S&F in repairs shutters including internal racks with MS black steel sheet of thickness not less than 1.60 mm in single piece sheet without joint area n.exc 1.5sqm each for built in cupboard complete all as specified and as directed.

S&F in repair 4 levers brass mortice lock vertical type, size 75mm with stainless steel handle including changing lever mechanism and handle and making smooth functioning in opening and closing of doors. Note: The rates includes the necessary provision of escutcheon plates and two keys

S&F in repairs aluminum (die cast) body door closer hydraulically regulated, desination No 1 universal type, suitable for door shutters upto 700mm in width and of weight not more than 35 Kg complete all as specified and directed.

Easing and adjusting to shutter of any description, area exc 1.00 but n.exc 4.00 sqm each and includes taking down, refixing in the same opening including builders hardware as required complete all as specified and directed. Note : New builder hard ware fitting shall be measured and paid separately under respective item of BoQ.

S&F 12 mm thick prelaminated particle board exterior grade with decorative choice laminations both sides for insertion to panels of aluminium shutters/partitions etc complete all as specified and directed .

S&F 4.8 to 5.00mm thick obscured or frosted sheet glass exc 0.5 sqm in each pane over and including and fixing by means of glazing pins, rubber beading and glazing filling materials in panels of partitions, windows, doors etc complete all as specified and directed .

S&F4.8 to 5.00mm thick coloured tinted sheet glass and fixing by means of glazing pins and rubber beading etc in aluminium partitions, doors, windows etc complete all as specified and as directed .

S&F solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed .

S&F 4.8 to 5.00 mm thick sheet glass area n.exc 0.5 sqm in each pane ordinary quality and fixing by means of glazing pins and rubber beading and glazing filling materials in panels of aluminium partitions, doors, windows complete all as specified and directed .

Dismantling wrought iron or mild steel in grill/guard bar (windows/ doors), railing (stair case) and steel work of any description not otherwise provided for complete all as specified and directed .

S&F mild steel framed work such as grills grating, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as directed.

M&L for preparation of new previously untreated steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed Notes :- Painting work on cuboard steel surface carried out through spary painting machine.

Demolition of brick work or stone boulder masonry, built in cement mortar all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles including removal from the site complete all as specified and directed.

M&L for brickwork with fly ash old size bricks having compressive strength not less than 75 Kg/Cm2 straight or curved on plan exc 6m mean radius, built in cement mortor (1:6). complete all as specified and directed .

All as per srl item No 45.00 here-in-before but half brick thick walls built in cement mortor (1:4). complete all as specified and directed .

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal fo debris and rubbish out side defence land complete all as specified and as directed .

M&L for rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete surfaces finished even & fair without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:4) on other than fair faces of brick work or concrete surfaces finished even & fair without using extra cement complete all as specified and directed.

M&L for rendering 6mm thick in CM (1:3) on brick work or concrete surfaces of ceiling finished even & fair without using extra cement complete all as specified and directed .

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand: 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified Notes : (i) Proposed washed stone grit plaster colour shall match with existing . (ii) White cement shall be used in lieu of ordinary cement in top layer of washed stone grit. (iii) Grooves shall be measured and paid separately,

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone girt plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specification and direction of the Engineer -in-charge.

M&L for applying wall care putty not less than 3mm thick over newly plasterd wall /vertical surfaces to achieve an even finished smooth surface for applying internal finishes complete all as specified and directed .

M&L for preparation of new plastered surfaces of walls and applying two coat of oil bound distemper over and including wall caré putty 3mm thick, on plastered surfaces, preparatory to distempering complete all as specified and as directed .

M&L for applying two coat of oil bond distemper over one coat alkali resistant primer on old surfaces of walls, including projections etc after complete removal of existing treatment and washing scrubbing down and stooping of existing treatment and making the surface even and smooth by applying layer of wall care putty not less than 3mm thick for distemper complete all as specified and directed

All as per srl item No 55 here-in-before but on ceiling except wall care putty

M&L for preparation of newly plastered surfaces of ceiling and applying two coat of OBD, preparatory to distempering complete all as specified and directed .

M&L for applying two coats of acrylic exterior emulsion weather proof paint of any tint including priming with alkali resistant primary paint on external new plastered surfaces complete all specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for as in columns, roof slab, Chajja, shelves, lintel band & WHB counter and reinforcement cut as required to facilitate demolition, and removal debris and rubbish from out side defence land complete all as specified and directed

M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. Note :- MS binding wire shall not be considered for purpose of measurements of weight.

M&L for reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded mechanically crushed stone aggregate) as in roofs/Chajjas, shelves, lintel bands WHB counter slab etc complete all as specified and as directed

Providing form work to roofs, chajjas, RCC shelves, lintel band, WHB counter slab and similar work including edges fair finished surfaces of flat concrete complete all as specified and directed

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), size 520x360x390mm including fixing bolts, PVC seat cover with mild steel chromium plated hinges (excluding flushing cistern and flush pipe ) complete all as specified and as directed . Make :- Super special colour of CERA Cat No S1050102 or equivalent in Jaquar / Parreware

S&F in repairs Vitreous China water closet squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed .

S&F in repair Wall Hung Water Closet with following accessories :- (i) Wall Hung water closet of size 365 X 360 X 545 mm including self close seat cover (PP), hinges, in builts jets & all accessories . Make:- Jaquar Cat Part No .FLS-WHT-5951/ Kohler Cat Part No. K-18131IN-S/Johson E-11050PW (White in colour) for WC. (ii) Slim Concealed Cistern with Floor Mounting Frame, Installation Kit and Drain Pipe Connection Set for Wall Hung WC (Without flush Control Plate) complete. Make:- Jaquar Cat Part No .CIB-WHT-31801011XF/Grohe rapid cat part No. SI-38536001/Kohler Model No. K-4178IN-2S with frame matching to the model. (iii) Control Plate Segment White/Chrome Slim for Concealed Cistern complete. Make:- Jaquar Cat Part No . CIS-CHR-31181810X/Grohe ASIN B014X33CUY/Johnson Chrome- G3471PC.

S&F in repairs Vitreous China wash basin, white, flat back, size 550 x 400 mm including PVC waste pipe, chain and plug and porcelain stopper, CP waste fitting 32mm dia and PVC bottle trap etc complete all as specified and directed . Make :- Super special colour of CERA Cat No S2040102 or equivalent in Jaquar / Parreware

S&F in repairs vitreous china Table top / wall hung / oval type ( under/over counter wash basin ) white size 550x460mm including CP waste fitting 32mm dia and CP bottle trap etc complete all as specified and directed . Make :- Jaquar cat No SLS-WHT-6601 or equivalent in CERA

S&F in repairs UPVC 32mm bore waste pipe of pressure rating 10 kgf/Sqcm, complete all as specified and directed .

S&F in repairs vitreous china half stall urinals, complete including providing and fixing plugs, securing urinals to plugs with and including 60mm long brass screws, fixing flush pipe, CP urinal Spreader fixed to water supply pipe, CP waste coupling, grating and union for discharge pipe complete all as as specified and directed . Make :- Ivory colour of CERA CALCIA Cat No S4020107 or equivalent in Jaquar /Parreware

S&F in repairs 10mm thick frosted acrylic sheet glass urinal partition of size 450 x900mm complete all as specified and directed .

S&F in repairs PVC valveless, syphonic action type, flushing cistern 10 ltr capacity, low level white with inlet ball valve, float, ,handle and brackets including fittings flush pipe 32mm bore complete all as specified and directed . Make:- Super Special colour of CERA CIENA PREMIUM Cat No B1010102 or equivalent in Jaquar

S&F in repairs bib taps long body chromium plated cast copper alloy half turn fancy type with crutch or butterfly handle screwed down suitable for iron pipe or brass ferrule of 15 mm bore complete all as specified and directed . Make :-Jaquar cat No FLR-5047N or equivalent in CERA

S&F in repairs pillar tap fancy type half turn long body push type time duly screwed for iron pipe and fixed 15mm dia bore complete all as specified and directed . Make :- Jaquar cat No FLR-5015 or equivalent in CERA

S&F 15mm bore brass chromium plated single lever basin mixture without pop up waste system with 450 mm long braided hoses etc complete all as specified and directed. Make:- Jaquar Cat Part No. VGP-81011B or equivalent in GROHE.

S&F in repairs chromium plated fancy Angle valve high pressure with crutch or butter fly handle screwed both end for angle valves cast copper alloy half turn , screwed iron pipe or for unions and fixed 15mm bore dia complete all as specified and directed . Make:- Jaquar cat No FLR 5053N or equivalent in CERA

S&F in repairs PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed . Make:- Jaquar cat No ALD 805A or equivalent in CERA

S&F in repair chrominum plated brass jet spray of 15mm bore faucet suitable for for EWC including PVC chord and brass nozzle and fixed to pipe complete all as specified and directed. Make :- Jaquar cat No ALD 579 or equivalent in CERA

S&F in repairs chromium plated health faucet, teliphonic type,with CP flexible arms and Jet, suitable to fixed and including 15mm bore CP angle valves, etc complete all as specified and directed. Make:- Jaquar cat No ALD 573 or equivalent in CERA

S&F in repairs toilet paper holder Chromium plated brass complete all as specified and directed. Make:- Jaquar cat No ACN 1153S or equivalent in CERA

S&F in repairs tubular towel rail,wall thickness not less than 1 mm, 20mm dia, D type, 60cm long between flanges of brass chromium plated bracket complete all as specified and directed . Make:- Jaquar cat No CAN -1111SM or equivalent in CERA

S&F in repairs brass chromium plated bottle trap 32 mm bore including jointing to waste fitting and pipe complete all as specified and directed. Make:- Jaquar cat No ALD769L2250x190 or equivalent in CERA

S&F in repairs CP brass Grating doom 100mm dia complete all as specified and directed . Make:- Jaquar cat No ALD769L2250x190 or equivalent in CERA

S&F in repairs chromium plated soap dish, any type, fixed to plug with chromium plated brass screws complete all as specified and directed . Make:- Jaquar cat No AKP-35731P or equivalent in CERA

S&F in repairs Push Button liquid soap containers with ABS body of capacity 0.80 ltr fixed with chromium plated brass screws and wooden/ plastic cleats complete all as specified and directed Make:-Jaquar cat No AKP-35735P or equivalent in CERA

S&F in repairs stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including necessary beading as required complete all as specified and directed .

Cutting chases, pinning in existing brick walls and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps cills etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting n. exc 10cm girth complete all as specified and as directed .

Dismantling old unserviceable PVC water storage tanks of capacity exc 250 ltrs & n.exc 500 Ltrs including supplying & fixing of any colour PVC water storage tank 500 ltr capacity HDPE, IS-12701 Marked double layered , cylindrical vertical type fixed and hoisted in position on roof upto 3 storey building complete with inlet/outlet of 20mm outer dia 3 layer PP-R pipe connection including closed top with locking arrangement including supply & fixing ball valves high prsessure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20mm dia and the minimum weight of valves 210 grms complete all as specified and directed by Engr-in-Charge Note : Inlet, outlet & wash out pipe will be measured and paid separately.

Dismantling old unserviceable PVC water storage tanks of capacity exc 500 ltrs & but n.exc 1000 Ltrs including supplying & fixing of any colour PVC water storage tank 1000 ltr capacity HDPE, IS-12701 marked double layered , cylindrical vertical type fixed and hoisted in position on roof upto 3 storey heigh building complete with inlet/outlet of 25 mm outer dia 3 layer PPR pipe connection including closed top with locking arrangement, including supplying & fixing Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight of valve 210 gms ) complete all as specified and directed by Engineer-in-Charge Note : ( Inlet, outlet & wash out pipe will be measured and paid separately.

S&F in repairs nipple of PTMT suitable for HDPE water storage tank of size 20mm bore dia of pipe (Minimum weight -45gms ) complete all as specified and as directed .

S&F in repairs 20 mm bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe of 20mm bore dia and fixed. (Minimum weight 20mm-210gms) complete all as specified and as directed .

Supply and fixing in repairs gun metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe of 20mm bore dia complete and fixed all as specified and directed by Engr-in-charge.

All as per srl item No 92.00 here-in-before but 25 mm bore dia.

Taking down 15mm bore steel water tubing and connections from any position including removing from site complete all as specified and directed.

All as per srl item No 94 here-in-before but 20 mm bore dia.

All as per srl item No 94 here-in-before but 25 mm bore dia.

S&F 20 mm outer dia, pipe 3-layer PP-R Polypropylene random copolymer (concealed pipes SDR 7.4 (PN 16) UV stabilized) and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed to walls, ceilings or in floors / roofs etc complete all as specified and directed . Note:- Cutting chases for concealed pipes & fittings etc wherever required and making good, disturbed surface in Cement mortar 1:3 shall be deemed to included in the unit quoted rate.

All as per srl item No 97 here-in-before but 25 mm outer diameter.

All as per srl item No 97 here-in-before but 32 mm outer diameter.

M&L for making connection of PP-R distribution branch with PP-R main of 16 to 40mm outer dia sizes by providing and fixing tee including cutting and making fusion joint complete all as specified and directed .

Demolition and breaking up drain pipes of 100 mm internal dia ( Salt glazed ware, AC or Reinforced concrete, PVC pipe or CI ) set in cement mortar complete all as specified and directed .

Demolition and breaking up drain pipes of upto to 75mm internal dia ( Salt glazed ware, AC or Reinforced concrete, PVC or CI pipe ) set in cement mortar complete all as specified and directed .

S&F UPVC pipe size 110mm for soil, waste, and vent, Type-B as per IS-13592 suitable for rubber ring joints, including all necessary specials and fittings (Confirming to IS-4735) such as bends, tees , junctions (with or without doors), reducers, WC connectors, couplers, cowels, clamps, rubber rings etc, fixing at walls/ceiling/floor supproted by MS clamp & hangers etc in concealed/inside duct/under floor & basement ceiling/external work etc. including chase cutting if required upto 03 storeyed high building and making good distrubed surfaces with existing.

All as per serial item No 103.00 here-in-before but but 75 mm.

S&F 110 mm bore PVC(SWR) 'P' / 'S' trap jointing with solvent cement complete all as specified and directed .

M&L for Single Seater workingable worktop including all necessary fittings & fixtures and comprises the followings : (i) Rectangular Workstation of size 1200mm x 600mm x 750mm (WXDXH) having worktop made of 25mm thick pre-laminated particle board (PLPB) conforming to IS:12823 Grade II, Type II duly edge bonded with 2mm thick PVC edge-banding tape, machine pressed/pasted at 200 digree celicious with hot melt glue & having 0.5mm thick balancing laminate on the bottom with all exposed and flat of boardedges duly sealed. (ii) Keyboard tray of size 550mm x 400mm x 18mm (WXDXT) made of 18mm thick pre-laminated particle board (PLPB)conforming to IS : 12823 Grade II, Type II duly edge banded with 2mm thick PVC edge bonding tape. (iii) CPU Trolley made out of 22 gauge thick CRCA sheet duly powder coated 45 microns with adjustment of four nylon Castors. (iv) Storage Pedestal Unit of size 400mm x 575mm x 725mm (WXDXH) having one drawer & one shutter cabinet with adjustable shelf. front fascia and top of the pedestal made out of 18mm thick pre-laminated particle board (PLPB) conforming to IS-12823 Grade II, Type II and rest of the pedestal body made of 12mm thick pre-laminated particle board (PLPB) conforming to IS : 12823 Grade II, Type II duly edge bonded with 2mm thick PVC edge-banding tape, machine pressed/pasted at 200 digree celicious with hot melt glue with all exposed and felt edges duly sealed. (iv) Partition panel of height 1510mm & 62mm thickness having modular / hybrid laminated /upholstered with Snap-on panel segments made of 12mm thick pre-laminated particle board (PLPB) conforming to IS 12823 Grade II, type II duly edge bonded with 2mm thick PVC edge banding tape, machine pressed / pasted at 200 digree calicious with hot melt glue with all exposed and flat edges duly sealed. (v) Wire management made through dual cable raceways running on two levels, one at skirting & another above or below the worktop.

M&L for Double Seater workingable worktop including all necessary fittings , fixtures shown in sketch and comprises the following. :- (i) Rectangular Workstation of size 2400mm x 600mm x 750mm (WXDXH) having worktop made of 25mm thick pre-laminated particle board (PLPB) conforming to IS:12823 Grade II, Type II duly edge bonded with 2mm thick PVC edge-banding tape, machine pressed/pasted at 200 digree celicious with hot melt glue & having 0.5mm thick balancing laminate on the bottom with all exposed and flat o boardedges duly sealed. (ii) Keyboard tray of size 550mm x 400mm x 18mm (WXDXT) made of 18mm thick pre-laminated particle board (PLPB)conforming to IS : 12823 Grade II, Type II duly edge banded with 2mm thick PVC edge bonding tape. (iii) CPU Trolley made out of 22 gauge thick CRCA sheet duly powder coated 45 microns with adjustment of four nylon Castors. (iv) Storage Pedestal Unit of size 400mm x 575mm x 725mm (WXDXH) having one drawer & one shutter cabinet with adjustable shelf. front fascia and top of the pedestal made out of 18mm thick pre-laminated particle board (PLPB) conforming to IS-12823 Grade II, Type II and rest of the pedestal body made of 12mm thick pre-laminated particle board (PLPB) conforming to IS : 12823 Grade II, Type II duly edge bonded with 2mm thick PVC edge-banding tape, machine pressed/pasted at 200 digree celicious with hot melt glue with all exposed and felt edges duly sealed. (iv) Partition panel of height 1510mm & 62mm thickness having modular / hybrid laminated /upholstered with Snap-on panel segments made of 12mm thick pre-laminated particle board (PLPB) conforming to IS 12823 Grade II, type II duly edge bonded with 2mm thick PVC edge banding tape, machine pressed / pasted at 200 digree calicious with hot melt glue with all exposed and flat edges duly sealed. (v) Wire management made through dual cable raceways running on two levels, one at skirting & another above or below the worktop.

S&F stainless steel (Grade 304 Jindal) mat finish colour , hollow (square/rectangle/round) tubes sections, channels, plates, angles, etc of any size and sections in railing , collapsible steel gate including all necessary welding, riveting, bolting, grinding, buffing, polishing and making curvature (wherever required) including necessary accessories, complete all as specified and directed.

Taking down existing teak wood hand rail under 40 sqcm section from steel balusters of stair case complete all as directed

Dismantling of wall and ceiling board (Fibre,pulp,insulation etc.) or insulation board /slab/blankets any thickness including cover fillet , GI Frame work and hangers /rod etc complete all as specified and directed by Engr-in-Charge.

S&F GI powder coated frame work for seamless false ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 0.9m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre or fixed with 6mm dia GI hanger (not exc 0.9m length) with ceiling cleat made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5 mm dia, 40mm long complete all as specified and directed

S&F perforated micro look false ceiling with fleece lay in type minimum 0.5 mm thick particle tiles of size 600x600mm for insulation and acoustic purposes, fixed to sanp grid frame work or with staples in ceiling complete all as specified

Cutting openings, through brick walls built in cement mortar, for door, windows and other openings or enlarging existing openings, converting window into door openings, etc. including providing, fixing and removing shoring, and brick/brick bats including mortar from the premises. complete all as specified and directed.

M&L for water proofing treatment to sunken portion complete all as specified and as directed in the following operations:- (a) Firstly removing/taking out all lean concrete/mud/brick bats as retrieved from site. (b) Rendering 15mm thick in CM (1:4) mixed with water proofing compound @ 2% by weight of cement including the cost of water proofing compound. (c) After drying of plastered surface, suitable primer such as multiplas primer/muliplas/cold sticker/ multiplas blown bitumen VG-10 shall be coated on the plastered surface. (d) MULTIPLAS @ 3 Kg/Sqm shall be unrolled over the coated surface (with overlap of 10cm) and bonded completely to the primed surface. The overlap shall then sealed by the tourch flame. (e) Toping with PLASFAL @ 2 Kg/Sqm. A layer of blown bitumen of VG-10 is applied @ 1.20 Kg/Sqm on MULTIPLAS. Plasfal memberan shall then be bonded on top of MULTIPLAS. (f) Re-filling the material which is obtained from above ser No (a) of this item before laying the concrete. Note:- (i) The above water proofing treatment shall be carried out by a specialized agency as approved by GE(I) upto G+2 floor without any extra cost. (ii) Minimum 10 years guarantee period for any leakage/seepage in sunken portion to be rendered by the Contractor/Firm. (iii) Concrete filling if required shall be measured & paid separately.

M&L for cutting / grinding of old terrazzo tiles or Kota stone floor / Marble flooring including vertical surface of wall in dado/skirting / steps of stair case etc with grinding machine and cutting 1st to VIIth with carborundum stone, 60 grit, 120 grit, 320 grit, 600 frit 1200 grit and 0 grit respectively including polishing complete all as specified.

S&F aluminium frame duly powder coated not less than 50 micron thick for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed by Engr-In-Charge.

S&F aluminium section duly powder coated not less than 50 micron thick for swing door / foldable noise free shutters partly panelled and partly glazed comprising top rail, bottom rail , lock rail and styles as per approved section and design and including necessary joining cleats, aluminium snap beading , rubber gasket glazing clips and two nos disc type handle and one nos aluminium tower bolt 200mm long for each leaf on one side and one number 6 lever dead lock of brass with for each leaf hinges fixed in position complete all as specified and as directed . Notes :- Insertion of glass /prelaminated partical board shall be paid & measured seaparately under relevent item of BOQ

S&F in repair for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in position.

S&F aluminium section duly powder coated not less than 50 micron thick for windows/ cupboard shutters (for fixed/openable/sliding design window) styles, side.top.bottom rails made out of aluminium section, shutter fixed or openable horizontal and vertical members of aluminium powder coated section and including aluminium beading rubber gasket, aluminium fittings such as 2 Nos hinges 75mm long, 02 Nos tower bolts 150mm long, 100mm stay rod and one handles 125mm long etc complete for each leaf complete all as specified Notes :- (i) Making AC opeing in window included in quoted rates nothing extra will be paid on this account (ii) Insertion pane of glass /prelaminated partical board shall be paid & measured separately under respective item of BOQ

S&F anodised aluminium section for partition partly glazed/ partly panelled parttions and fixed glazing frame made out of aluminum frame section including necessary joining cleats, glazing clips, rubber packing anodised aluminium snap beading screws etc frame work fixed to walls, floor and ceiling with raw plug wherever required complete for each leaf complete all as specified and as directed . Notes :- Insertion pane of glass /prelaminated partical board shall be paid & measured separately under respective item of BOQ

S&F aluminium section duly powder coated not less than 50 micron thick for ventilator, partly glazed and partly louvers, outer frame & mullion fabricated with aluminium section as, including rubber beading, & glazing clip, half portion louvers of 80 mm wide & frosted glass including aluminium louver patti including S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aperture with 25x3mm thick aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position complete all as specified and directed by Engr-in-charge. Notes :- Insertion pane of glass /prelaminated partical board shall be paid & measured separted under relevent item of BOQ

S&F aluminium section duly powder coated not less than 50 micron thick for window grills complete with necessary 'U' shaped aluminium channel alround fixed in window frame /opening with screws complete all as specified and directed

Taking down old unserviceable exisitng venetian blinds including frame work complete all as specified and directed .

M&L for for vertical fibre cloth venetian blinds consisting of aluminium head rail vanes/ louvers of 80 mm width of flaps driven string of approved tint and traverse cord fixed in position complete all as per manufacture instructions

M&L for manullay opening and closing roller type blinds approved make with charecteristic composition 100 % polyester (translucent), weight 230 gm/ Sqm maximum width 2.60m thickness 0.37 mm fixed in position all as per manufacture instructions complete, all as directed.

M&L for complete removal of existing treatment, cleaning the surface with emery paper 180 and applying one coat of primer and subquently with putty for making the surface smooth for receiving two coat of base paint (tint) including two coat textured wall painting with premium acrylic (textured) emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grms/ltrs of approved brand with two protective coat and as per manufacture instruction complete all as specified and directed. Note:- Colour shade of texture painting as approved.

M&L for preparation of old steel surfaces of any description over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint complete all as specified.

M&L for applying two coats of synthetic enamel paint over one shop coat primery on factory made steel surfaces such as pressed steel frame

M&L for preparation of new wood or wooden based surfaces of any description, over 10 cm in width or grith not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

All as per srl item No 128 here in before but on wood or wooden based surfaces.

E/M (Portion) Taking down unserviceable point wiring any type for light, fan, power etc including unserviceable switch,socket, regulator light fitting and ceiling rose etc of any make complete including making good disturbed surfaces of walls ,floors roof etc with existing surfaces complete

Taking down of Celling Exhaust Fan carefully and deposit in safe custody and refixing the same after painting with synthetic enamel white paint by spraying machine, including ,greasing,minor repairing on the completion of the work all as specified and directed.

M&L for Point wiring with 2 single core 1.5 Sqmm multistranded copper conductor cable multistranded, FRLS PVC insulated and unsheathed in non metallic PVC concealed connduit 20 mm bore dia with necessary fitting including cutting chasing for conduits and terminal boxes with all fittings /accessories and including 1.5 Sqmm PVC insulated copper earth wire connected to common earth with terminal boxes for Modular fittings including acessories as modular surface cover plate with frame, for one light/Fan/Exhaust Fan/bell point complete all as specified and directed.

All as per srl item No 134 here- in- before but using cable size 1.5 Sqmm for 1 Nos 06 Amps Socket outlet independent with terminal boxes, Modular fittings including acessories as modular surface cover plate with frame, metal flush box,complete all as specified and dierected.

All as per srl item No 134 here- in- before but using cable size 1.5 Sqmm for 06 Amps Socket outlet independent but below the switch board with terminal boxes, modular fittings including acessories as modular surface cover plate with frame, metal flush box complete all as specified and dierected.

All as per srl item No 134 here- in- before but using cable size 1.5 Sqmm for 1 Nos 06 Amps Socket outlet on the same board with other switches complete all as specified and as dierected.

All as per srl item No 134 here- in- before but using cable size 2.5 Sqmm for 15/16 Amps Socket outlet terminal boxes for Modular switches.

All as per srl item No 134 here- in- before but using cable size 4.00 Sqmm with 4.00 sqmm earth wire for one three pin switch socket outlet 15/16 Amps point with terminal boxes.

S&F sheet metal single pole and neutral enclosure with 2 pin and earth plug top and socket complete with one single pole MCB 20 Amps complete (Cat No 507811 of Legrand or equivalent in Havells/L&T

S&F modular switch 6 Amp single pole one way-1 module (Cat No 574800 of Legrand or equivalent in Havells/Anchor Roma.

S&F modular switch 15/16 Amp single pole one way-1 module (Cat No 574808 of Legrand or equivalent in Havells/Anchor Roma.

S&F modular socket outlet shuttered-6A-2/3Pin-universal India 2 Module complete. (Cat No 574833 of Legrand or equivalent in Havells/Anchor Roma.

S&F modular socket outlet shuttered-6/16A-2/3Pin Indian 2 Module complete. (Cat No 574834 of Legrand or equivalent in Havells/Anchor Roma.

S&F electronic fan step regulator 120W - 2 module (Cat No 574831 of Legrand or equivalent in Havells/Anchor Roma.

M&L for Ceiling rose 3 terminal PVC/polycarbonate complete

M&L for Modular Bell push 6 Amp 2 Module (Cat No 574824 of Legrand or equivalent in Havells/Anchor Roma.

M&L for Bell multi music type complete.

S&F LED light fitting 20W CRCA batten with decorative end cap complete with retrofit T8 Polycarbonate/Glass tube 20 watt complete. (Cat LTDC011220WLED/WD) of C&S or equivalent in Havells/CG.

S&F LED indoor decorative aluminium extruded T5 LED battens integrated type with Glass tube rod 10 watt complete including connection from ceiling rose to light fittings with 3 core 1.5 Sqmm multi stranded copper conductor cable (CAT LTTB2F10WLED/W of C&S or equivalent in Havells/CG.

S&F LED light fitting surface mounted 2x2 (600x600x70) of capacity 36W complete with all connected accessories complete including connection from ceiling rose to light fittings with 3 core 1.5 Sqmm multi stranded copper cable (CAT LTCSP36WLED2x2 of C&S or equivalent in Havells/CG). Note : In this item 145 Nos light fittings shall be surface mounted type and remaining 17 Nos recessed mounted type.

M&L for MCB Vertical TP&N distribution board suitable for Incommer MCCB 160 Amps and SP/TP MCBs as outgoing 12 way double door complete all as specified and directed (Cat No 507748 of Legrand or equivalent in Havells/L&T)

S&F sheet metal enclosure SPN 12 Way with acrylic door having 200 Amps rated copper bus bar 240 Volts AC complete.(Cat No 507622 of Legrand or equivalent in Havells/L&T)

M&L for MCB single pole & Neutral 63 Amps. C Curve 240 V (Cat No 408620 of Legrand or equivalent Havells/L&T)

M&L for MCB single pole 6-32 Amps C Curve 240 Volt. (Make Legrand or equivalent in Havells/L&T)

Supply & Fixing in of DLP trunking aluminium type single compartment of size 105 x 50mm and covers width 85mm duly fittied with 06 Nos modular socket 5 Amps 2 module complete adoptable type of size 105x50mm with one compartment duly covered installed with suitable arteor support joints including end caps of suitable dia pipe including all accessory fittings complete all as specified and directed.(Cat No. 011100 & 011111 of Make Legrand or equivalent in AKG//L&T.

Supply & Fixing in renewal of DLP trunking system plastic adoptable type 150x50mm double compartment and width of cover 2x65mm duly covered installed with suitable arteor support joints,partitions including end caps of suitable dia pipe including all accessories complete all as specified and directed.(Cat No 010432 & 010521 of Make:- Legrand or equivalent in AKG/L&T.

Supply and fixing dual ceiling mounted switch sensor movement detection 360 degree with option of setting vacancy & occupancy mode (Push button over ride or moble configuration) automatic terminal connection. PIR & US dual tech coverage 80 Sqmm with diameter 11m having time delay setting from 0 to 60min, suitable for 100w -250w LED connected load including necessary wiring with 1.5 Sqmm copper cable single core complete & testing after installation. (Cat No. 048806 of Legrand or equivalent make of Hager/L&T)

Supply and fixing digital programming set suitable to adjust the setting of motion sensor to the nearest one decimal places suitable for setting of each detector complete (Cat No 088230 of Legrand or equivalent in Hager/L&T)

M&L for in renewal of sub main wiring complete using 4 run of 25 sqmm and two run of 16 sqmm PVC insulated unsheathed FRLS multistranded copper conductor ISI marked 1100 V grade in concealed non metallic PVC conduit of 32mm in wall/floor,passing through wall/ceiling complete all as specified and directed.

M&L for in renewal of sub main wiring complete using 2x 2.5 sqmm and 2.5 sqmm earth wire PVC insulated FRLS multistranded copper conductor ISI marked 1100 V grade in non metallic PVC concealed conduit in suitable dia fixed in wall/floor,passing through wall/ceiling complete.

M&L for in renewal of sub main wiring 2x4.0 sqmm and 1x4 Sqmm earth wire non matellic PVC insulated FRLS of suitable size multistranded copper conductor ISI marked 1100 V grade in non metallic PVC concealed conduit fixed in wall/floor,passing through wall/ceiling complete.

M&L for in renewal of sub main wiring 2x10 sqmm and 1x10 Sqmm earth wire PVC insulated FRLS of suitable dia multistranded copper conductor ISI marked 1100 V grade in non matellic PVC concealed conduit of 25mm dia fixed in wall/floor,passing through wall/ceiling complete.

Material and Labour for earthing complete with GI earth plate electrode 600mmx600mmx6mm thick burried in ground vertically to a depth not less than 2.25meters below ground level with top edge of the earth plate at a depth not lesss than 1.5 meter below the ground level, earth plate surrounded 15cm thick layers of common salt and charcoal dust starting from ground below and above 15 cm of earth plate. GI plate connected with galvanised iron strip of 32x6mm by means of Copper nuts, bolts and washers. Strip laid in 40mm dia light grade GI pipe as protection from top of the plate up to test point (cost of protection pipe up to 7.5 meters from earth electrode will be included in the rates quoted by the contractor) with following:- (a) GI strip of size 32mm x 6mm. (b) Watering pipe GI light grade 20mm dia from top of the earth electrode up to MS funnel with wire mesh embeded in floor of PCC earth pit. (GI Funnel should properly tightned on GI watering pipe and embeded in PCC floor of earth pit with open top suitable for watering of earth pits) (c) PCC earth pit 30x30x30cm internal dimension constructed in PCC 1:2:4 type B1 exposed surfaces smoothly finished with 15mm thick cement mortar 1:6 plaster including RCC 1 :2:4 type B0 reinforced with 8mm dia deformed bars @100 mmc/c bothways pit cover 25mm thick with 2 Nos MS handles of 12mm dia suitable for carrying of pit cover. (d) Angle iron frame made of 40x40x4 mm for 30x30 cm PCC pit for holding the pit cover. (e ) Apply two coat of syntheticnenamel paint over one coat of red oxide zinc chrome primer on exposed steel surfaces and two coat of hot tar on embedded portion of steel surfaces.

M&L for Galvanised iron strip 32x6mm buried in ground including necessay excavation & earth work in soft/loose soil and removal of surplus excavated material n. exc 50m and depositing where directed.

M&L for fixing MCCB Four pole 160 Amps 25KA

Material and Labour for earthing in any type of soil complete with GI earth plate electrode 600mmx600mmx6mm thick burried in ground vertically to a depth not less than 2.25 meters below ground level with top edge of the earth plate at a depth not lesss than 1.5 meter below the ground level, earth plate surrounded 15cm thick layers of common salt and charcoal dust starting from ground below and above 15 cm of earth plate. GI plate connected with galvanised iron wire 4mm dia by means of nuts, bolts and washers. GI wire laid in 15 mm dia light grade GI pipe as protection from top of the plate up to test point (cost of protection pipe up to 7.5 meters from earth electrode will be included in the rates quoted by the contractor) with following:- (a) GI wire of size 4mm . (b) Watering pipe GI light grade 20mm dia from top of the earth electrode up to MS funnel with wire mesh embeded in floor of PCC earth pit. (GI Funnel should properly tightned on GI watering pipe and embeded in PCC floor of earth pit with open top suitable for watering of earth pits) (c) PCC earth pit 30x30x30cm (internal dimension) 120mm thick wall on 500x500x150mm PCC base 1:3:6 in PCC 1:2:4 type B-1 exposed surfaces smoothly finished with 15mm thick cement mortar 1:6 plaster including RCC 1:2:4 type B-1 pit cover 25mm thick reinforced with 8 mm dia deformed bars @ 100 mm c/c both ways with 2 Nos MS handles of 12mm dia suitable for carrying of pit cover and angle iron frame of 40x40x4mm complete. (d) Angle iron frame made of 40x40x4 mm for 30x30 cm PCC pit for holding the pit cover. (e ) Apply two coat of syntheticnenamel paint over one coat of red oxide zinc chrome primer on exposed steel surfaces and two coat of hot tar on embedded portion of steel surfaces.

S&F non metallicPVC conduit 20mm dia including fittings/accessories concealed in wall including cutting chasing and making good to disturb surfaces complete.

M&L for Galvanised iron wire OF 4mm dia fixed on wall from earth test point to main switch board complete.

S&F Telephone socket RJ11.

S&F telephone cable in concealed PVC conduit including connecting in telephone socket complete.

Taking shut down, dismantling of old LT panel and S&F in door type cubical panel board suitable for 3 phase, 4 wired, 415V, 50 Hz and tested at CPRI for 35 MVA repturing capacity at 415 volts factory fabricated in an approved factory with CRCA sheet of size 1500x1500x1500 mm 2 mm thick having modern fabrication process powder coating in approved shade having thickness not less than 100 microns provided with suitable gasket to make it dust and vermin proof and general constructions conforming to IS8623/93. LT Panel shall be front and back openable and having inner and outer shells, the inner shells dulycompartmentalized for each control gears, panel should have suitable size of Aluminium bus bar three phase 4 wired system having current carrying capacity 1000 Amps . The panel should have the following incoming and outgoing controls duly fixed with the panel by means of suitable link plates complete all as speccified and as directed .(PCC platform of suitable size for mounting the feeder pillar box is deemed to be included in the quoted rate) and to accommodate the following incoming and outgoing controls and suitable size :- INCOMING (i) MCCB 630 A, 4 pole breaking capacity 50KA(Make:- L&T, Siemens, Schneider, ABB)-1 No. (ii) Digital Multi-functional meter VAFPP (Voltage, current , frequency, power factor-1 No. (iii) Phase indicator lamp (LED type) 1 set (set of three). OUTGOING (i) MCCB 160A 4 pole breaking capacity 25 KA (Make:- L&T, SIEMENS, Schneider, Legrand,ABB)-06 Nos (ii) MCB TP 63 Amps - 06 Nos. (iii) MCB SPN 40 Amps - 10 Nos. Changeover Switch (i) Changeover switch on load type front operated of capacity 630 Amps 4 pole-01 Nos (Make Havells/L&T/Schenider)

Material &labour for point wiring for one light point or one fan/exhaust/bell point controlled by one switch with using 1.5 Sqmm(nominal area) stranded copper conductor , two single core, PVC insulated & unsheathed cable FRLS 1100 Volts grade in existing concealed conduit as directed with terminal boxes suitable for modular fitting including accessories as modular surface cover plate with frame and using 1.5 Sqmm (nominal area) stranded copper conductor single core PVCinsulated & unsheathed FRLS cable as in earth wire connected to earth dolly complete all as specified and directed.

R.K ENGINEERS & CONTRACTORS

Commercial Traders

Leo Network power systems

G and G Infratech Private Limited

JAIN BUILDER