Construction works of internal and external part of 3rd and 4th floor over existing building of Assam Higher Secondary Education Council at Bamunimaidan, Guwahati-21

Amount

Providing & fixing of Flotex Flocked Textile floor covering of Nylon 6.6 face fiber or equivalent of approved make with 100% Nylon and completely water proof resilient backing. The flooring should be anti-static with thickness of 4.3mm, and approx. weight of 1.8 kg/ sqm.of roll form. The carpet should be completely stain resistant and of a density approx. 80 million fibers/sqm.in the width of 2mtr. The floor covering should have Fire test EN- 13501, Appearance Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 class DS, Sanitized anti-microbial treatment, with resilient waterproof backing, anti-allergic which is certified by British allergy foundation, with ten year replacement guarantee complete in all levels as directed.

Providing fitting and fixing Armstrong make 12mmx75mm one side rounded edge wooden skirting as approved and directed.

Providing & fixing Armstrong WoodWorks Channeled acoustical wall panels available in nominal size of 792x24O mm having thickness of 15mm. The two long sides interlock with a tongue and groove detail. The two short ends are cut square. Clips I hold the panels to the wall (along the aluminum keel) or to a i grid ceiling. When installed as a wall, the panels can run I horizontally or vertically. The same panels can be used as I ceiling planks when installed on grid system.

Supplying, Fixing and Fitting of not less than 75 mm thick partition wall with 12 mm thk Calcium Silicate "Hilux Boards" make fixed over Gyp steel flanged studs fixed vertically on floor and ceiling at interval of 600mm c/c. The 12 mm thick calcium Silicate board of approved brand to be fixed on the both sides with 25mm drywall screw at 300 mm c/c to one sides of 50 mm studs (0.55 mm thk having one flange of 34mm and another of 36 mm) made of GI steel with joints staggerred, to be complete in all levels as per design and as directed by the department.

Providing and fixing 2.4m high FRAMELESS GLASS INTERNAL PARTITIONS at all locations with 12mm clear tempered glass or as per elevation drawings enclosed with approved make of 316 grade patch connector S.S. fittings of DORMA/Ozone or equivalent make , fixed with S.S. screws or with fixing clips including necessary filling up gaps at junction, at top, bottom u channel make jindal and sides with required weather silicon with backer rod shall be inserted between alluminium section channel and glass as well as both inside and outside around the periphery of the glass to make the glazing water tight and air tight as shown in enclosed drawings and directions of Engineer-in-charge. Glasswork including making suitable holes in the glass before tempering process of glass, for installation complete as per design drawings. The periphery shall have to be sealed both from inside and outside with silicon weather sealant to make the glazing water and air tight.The sealing of glass to patch connector hardwares with stainless steel fixtures as detailed in drawings. Silicon sealant grade shall be "Dow corning - USA" or " "WACKER - Germany" or approved equivalent as per the design requirement. The partition shall be aligned for the entire height and for the entire length by laser beam equipment to ensure 100 percent X-axis and Y-axis alignment. The glass joints must be properly sealed with weather silicon to make the joint water tight and air tight as well as per design complete at all levels and as directed.

Providing ditting and fixing of 30 mm thk BWP grade green/century/ or equivalent)solid core flush door with 6mm glass panels fixed on rebate on the face and timber beads on back. The edges of the flush door shall be finished with 6mm thk teak wood liping. The timber beads and teak wood lipping shall be polished as per the approved shade of colour and the door to be finished with 1 mm thk laminate of Greenlam/Century/Merino make on both sides as well as the rebate including nessecary harware fittings like 100 mm SS hinges and screws, complete at all levels as per design and as directed.(lock, door closer/floor spring, tower bolt) to be measured seperately.

Providing, supplying and fixing of Frameless Single leaf/double Swing Glass Door of Dorma/ Ozone or equivalent make in glazing using 12mm thick toughened glass of Saint Gobain / or approved equivalent with die cast patch fitting with stainless steel cover including fixing of patch fittings, floor springs, locks, handles etc. using the hardware items as detailed, complete in all respects as per detailed drawings, specifications and direction of Engineer in charge. Single Leaf Door with Dorma or Equivalent Hardware’s as specified:- Swing Glass Door which includes each of Top Pivot PT 24, Bottom Patch PT 10, Top Patch PT 20, Floor Lock US 10, Strike Plate , Floor Spring BTS 75v, with pair of TGDIH SS Pull Handle 25 mm dia x 450 mm long and other accessories for self closing feature as per detailed drawings.

Providing, fitting and fixing of 75 mm manually operated Black out Roller blinds with necessary hardware complete as per choice and as directed.

Supply and installation of Merino /Greenlam (Nylon) series cubicles of width and depth as per specifications/ site drawings. Cubicle height will be 2003 mm. Made from solid grade compact high pressure laminate as per IS:2046 and EN-438 manufactured under high specific pressure > 5 MPa and temperature >120°C with bunch of kraft papers impregnated with thermosetting phenolic resin and decorative papers made of Alpha cellulose fiber impregnated with thermosetting melamine resin which provide superior scratch, abrasion, heat, chemical, impact, graffiti & moisture resistance along with anti-bacterial properties. Panels have a black core that when machined, presents a distinctive black edge. All doors will be of single colour and made of 12 mm thick HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 no.s Nylon PA-6 made hinges affixed to the pilasters. Nylon PA-6 made coat hook and lock set are provided with each door. All pilasters will be made of 12 mm thick HPL compact panel with chamfered edge and completed with stainless steel made thumb turn lock set. Aluminum made door stopper profiles with rubber linings for dampening the noise while door closing will be provided at the vertical ends of the pilasters. Pilasters will be anchored to the floor using Nylon PA-6 made adjustable legs .The bottom gap is 100-150 mm. All intermediate partitions or dividers will be made of 12 mm thick HPL compact laminate panels. They are affixed with aluminium made U-channel at their ends for ultimate stability of the system. Design no. as specified by Arch. / Engr. in suede finish. Size of panels to be as per drawing.

Supply fitting and fixing of wall paper on finished wall surface with necessary glue as per architects choice complete as directed by the department at all levels.

Supplying, fitting, fixing Suspended Ceiling which includes G.I. perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending G.I. intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angle of width 25mmx10mmx0.55mm thick fixed to soffit with G.I.cleat and steel expansion fasteners. Ceiling sections of 0.55 mm thk with knurled web of 51.5 mm and two equal flanges of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips perpendicular to the intermediate channel at 457mm c/c and 12 mm thk BWR grade Ply Board fixed to the ceiling sections with 25 mm drywall screws at 230mm c/c. the boards are finished with 4 mm thick natural veneer of Green/Century make and polished complete with PU polish at all levels including cutting for providing and fixing light fixures whwre ever necessary. and as per design.

V SHAPED BOARD ROOM TABLE MAIN TABLE : 2400W X 750D X 750HT (01 NOS) SIDE TABLE : 1500W X 750D X 750HT (10 NOS) Specifications Table top : 25mm thick Pre-laminate particle board finished with 2mm edge lipping. Support : Supported on 25 mm thick PLB Gable Ends with necessary cross beams. Modesty Panel : 18mm thick PLT Modesty Panel of 450 mm ht is considered. Wire Management - 450L Flip provided for each table with PVC cable dump and wire entry boxes

Conference Main Chair. Model: FP Optima HBSSN 3D High mesh back chair. Fabric Upholstered Cushioned seat Multilock mechanism. Seat sliding mechanism. Three way adjustable arms. Chrome magna base Make: Featherlite

Conference Staff Chair Model: Amaze MB. Medium back mesh chair. Self Calibrating mechanism. Synchro mechanism with multilock mechanism Height adjustable arms. Nylon base Make: Featherlite

Conference Fixed Chair Model: Contact Project VA. Contact Project. Mesh Back Visitors chair. Powdercoated Sledge Base. Fixed Arms Make: Featherlite

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass door latch with necessary screws etc. complete : 300x16x5 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Marble work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately). Area of slab over 0.50 sqm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Marble work

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main T at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Supplying installation, testing, programming and commissioning of Audio equipment ON TABLE BOUNDARY MICROPHONE for any conferencing system: Frequency response 40 Hz – 20 kHz, Nominal impedance 200 Ω, Sensitivity 10 mV/Pa. Frequency Response :- 40 Hz - 20 kHz, Max. sound pressure level:- 140 dB, Sensitivity :- 10 mV/Pa, Dynamic range :- 111 dB (A) (Make:- Sennheiser/ Beyerdynamic/ Audio Technica)

Supply, Installation, Testing and Commissioning of DSP core with 16 user-configured card slots, Lua scripting engine, optional software-licensed HearClear AEC. (Make:- Xilica/ Biamp/ BSS)

Supply, Installation, Testing and Commissioning of Analog Input Card having 2 Mic/ Line Inputs. (Make:- Xilica/ Biamp/ BSS)

Supply, Installation, Testing and Commissioning of Analog Output Card having 2 Mic/ Line Outputs. (Make:- Xilica/ Biamp/ BSS)

Supply of Audio equipment,8" Open‐Back Ceiling Speaker. 70V/100V taps at 6W, 3W, 1.5W (plus 0.75W at 70V), very high 97 dB sense, 50 Hz to 16 kHz, for non‐plenum applications, 1.4 kg (3.0 l. (Make:- JBL/ Turbosound/ Bosch)

Supply, Installation, Testing and Commissioning of Eight-channel, 125W @ 4Ω Power Amplifier (Make:- Crown/ Labgruppen/ Behringer)

Supplying installation, testing, programming and commissioning of Professional 8-Channel 3-Bus Mic/Line Zone Mixer with Remote Control and Link Ports; 6 Ultra-low noise Mic/Line Inputs With Gain Control, -20 dB Pad, Level/Clip indicator, +48 V Phantom Power And Bus-assign Switches (Make:- Behringer/ Midas/ Yamaha)

Supplying installation, testing, programming and commissioning of Wireless hand held microphone system. (Make:- AKG/ Sennheiser/ Shure)

Supply and Installation of High flexible Speaker cable for power amplifiers upto minimum 500 Watt , Jacket - PVC, ø 0.32 in, black Conductor - Stranded bare copper wires, 140x35 AWG (13AWG) (Make:- Gotham/ Klotz/ Belden)

Supply and Installation of Audio Signal Cable;Balanced microphone cable with single shield, high flexible, velvet faint PVC-Jacket , Conductor: Stranded bare copper wires 28 x 0.10 mm (0.22mm²) , Jacket: PVC, 6.0 mm max. Ø (Make:- Gotham/ Klotz/ Belden)

Supply and Installation of Required Connectors like XLR, RCA, EP, Mono Jack, Stereo Jack, VGA Connectors, PVC Conduits and other accessories etc. (Make:- Amphenol/ Neutrik)

Supply and Installation of 10KVA Online UPS with 16 Nos SMF Batteries, Rack and Accessories. (Make:- Numeric/ Delta/ APC)

Supply and Installation of 5,000 lumens XGA laser light source projector. Display system:- 3 LCD system, Size of effective display area:- 0.63”(16.0 mm) x 3 BrightEra LCD Panel, Aspect ratio: 4:3, Number of pixels:- 2,359,296 (1024X 768X 3) Pixels. (Make:- Sony/ Panasonic/ Viewsonic)

Supply, Installation, Testing and Commissioning of Motorized Projection Screen 8X6 Feet (Make:- Liberty/ Milan))

Supply, Installation, Testing and Commissioning of Projector Ceiling Mount Kit (Make:- Liberty/ Milan)

Supply, Installation, Testing and Commissioning of 55" 4K Ultra HD Commercial Display. Type/ Tech: "TFT LCD Module. IPS type, DLED backlight", Display Area (mm): 1209.6 (H) x 680.4 (V) (55” diagonal), Native Resolution: 3840 x 2160, Aspect Ratio: 16:9, Colors: 1.07B colors, Brightness: 400 nits (typ.), Contrast Ratio: 1200:1 Typ., Viewing Angles: H = 178, V = 178 typ. (Make:- Viewsonic/ Panasonic/ Sony)

Supply, Installation, Testing and Commissioning of POPUP BOX; Easy Access To Connectors Durable Pnematic Movementand Mechanical Latching Mechanism One Female 15pin HD Connector And 3.5mm Mini Stereo Audio Jack, Two CAT RJ45 network/data/phone Connectors, Two Unswitched AC Outputs, One HDMI (Make:- Magnum/ Extron/ Kramer)

Supplying installation, testing, programming and commissioning of Video equipment HDMI HDBaseT-Lite Extender (4K@40m)(HDBaseT Class B): Video: Max. Data Rate 10.2Gbps (3.4Gbps per lane) 10.2Gbps (3.4Gbps per lane), Max. Pixel Clock 340 MHz 340 MHz, Compliance HDMI (3D, Deep Color, 4K) HDCP Compatible, HDMI (3D, Deep Color, 4K) Max. Resolutions / Distance Up to 4K@35m (Cat 5e/6) / 40m (Cat 6a/ATEN 2L-2910 Cat6); 1080p@60m (Cat 5e/6) / 70m (Cat 6a/ATEN 2L-2910 Cat6) 4K supported: 4096 x 2160 / 3840 x 2160 @ 60Hz (4:2:0); 4096 x 2160 / 3840 x 2160 @ 30Hz (4:4:4) (Make:- Kramer/ Aten/ Extron)

Supplying installation, testing, programming and commissioning of 17U Floor Mount Racks: Basic Frame Steel; Construction Welded; Top & Bottom Cover Welded to Frame with Cable entry exit cut outs; Front Door Lockable Toughened Glass Door; Rear Door Lockable Steel Door; 19” Mounting Angle Formed Steel; Std. Equipment Mounting DIN Std. 10mm Sq. Slots; Standard Finish Powder coated; Standard Colour Grey & Off White OR Black; Standard Mounting Caster wheels (2 with Brake & 2 without Brake); Rack Standard Conforms to DIN 41494 or equivalent standard (Make:- Valrack/ Nettrack/ APW)

Supply and Installation of 10 mtr High-performance Cables With Molded HDMI Connectors At Both Ends. HDMI Standard Supports High-definition Video Plus Multi-channel Audio In A Single Cable. (Make:- Kramer/ Aten/ Belden)

Supply and Installation of 1 mtr High-performance Cables With Molded HDMI Connectors At Both Ends. HDMI Standard Supports High-definition Video Plus Multi-channel Audio In A Single Cable. (Make:- Kramer/ Aten/ Belden)

Supply and Installation of Shielded Cat 6 Cable (Make:- Molex/ Dexathron)

Supply and Installation of RJ45 Connector (Make:- Molex/ Dexathron)

Supply, Installation, Testing and Commissioning of HD 1080p Indoor IR Turret Camera. 2 megapixel high performance CMOS, Analog HD output, up to 1080p resolution. (Make:- Hikvision/ Honeywell/ Dahua)

Supply, Installation, Testing and Commissioning of HD 1080p IR Bullet Camera. 2 megapixel high performance CMOS, Analog HD output, up to 1080p resolution. (Make:- Hikvision/ Honeywell/ Dahua)

Supply, Installation, Testing and Commissioning of 32CH DVR. Support H.265 Pro+/H.265 Pro/H.265 video compression, Support HDTVI/AHD/CVI/CVBS/IP video input, Max. 32/40 IP cameras input, Max. 800 m for 1080p and 1200 m for 720p HDTVI signal transmission. (Make:- Hikvision/ Honeywell/ Dahua)

Supply and Installation of 43" LED Display Panel. Screen Size 43-inch, Aspect Ratio 16:9, Resolution 1920 x 1080 pixels, Video In, Audio In, HDMI in , USB In, VGA IN (Make:- LG/ Panasonic/ Viewsonic)

Supply and Installation of 32" LED Display Panel. Screen Size 32-inch, Aspect Ratio 16:9, Resolution 1920 x 1080 pixels, Video In, Audio In, HDMI in , USB In, VGA IN (Make:- LG/ Panasonic/ Viewsonic)

Supply and Installation of Power Supply (Make:- Protek/ MX)

Supply and Installation of Video Balloon Connector (Make:- Digisol/ MX)

Supply and Installation of DC Connector

Supply, Installation, Testing and Commissioning of 2 MP Fixed Bullet Network Camera. High quality imaging with 2 MP resolution, Efficient H.265+ compression technology, Clear imaging against strong back light due to DWDR technology, Water and dust resistant (IP67). (Make:- Hikvision/ Honeywell/ Dahua)

Supply, Installation, Testing and Commissioning of 2 MP Bullet Network Camera. High quality imaging with 2 MP resolution, Excellent low-light performance via powered-by- DarkFighter technology, Efficient H.265+ compression technology Clear imaging against strong back light due to 120 dB true WDR technology Water and dust resistant (IP67) (Make:- Hikvision/ Honeywell/ Dahua)

Supply, Installation, Testing and Commissioning of 32-ch 1.5U 4K NVR. Up to 32-ch IP camera inputs, H.265+/H.265/H.264+/H.264 video formats Up to 2-ch @ 8MP or 4-ch @ 4MP or 8-ch @ 1080P decoding capacity (Make:- Hikvision/ Honeywell/ Dahua)

Supply , Installation , Testing and Commissioning of L3 managed full 10G Ethernet core routing switch with 24*1/10G SFP+ fiber ports and 4*40/100G QSFP28 fiber slot ports. Redundant dual AC power supply. Core Switch with switching capacity of 1.28Tbps. (Make:- D-Link/ Digisol/ Netgear)

Supplying, installation, testing and commissioning of 24-Port KVM over IP Switch with 24 nos USB VGA Virtual Media KVM Adapter complete as required (Make:- D-Link/ Digisol/ Netgear)

Supply, Installation, Testing and Commissioning of Cat 6 Keystone I/O Port. (Make:- D-Link/ Digisol/ Netgear)

Supply and Installation of Cat6 Patch cord 2 Mtr (Make:- D-Link/ Digisol/ Netgear)

Supply and Installation of Cat6 Patch cord 1 Mtr (Make:- D-Link/ Digisol/ Netgear)

Supplying, installation, testing and commissioning of 16 Port CAT6 Universal Patch Panel with Individual Port Transparent Shutter, (Unloaded/Loaded) with Cable Support Bar

Supply ad Installation of 4U Wall Mountable Equipment Rack (Make:- Nettrack/ Valrack/ LinkEu)

Supply and Installation of 17U Floor Mounted Equipment Rack (Make:- Nettrack/ Valrack/ LinkEu)

Supply and Installation of 10KVA Online UPS with 16 Nos SMF Batteries and Rack for Batteries. (Make:- Delta/ Numeric/ APC)

Supply, installation, testing and commissioning of Air Conditioning system with Variable Refrigerant Flow system, comprising of the following: Supply of 415v - 3 Ph - 50 Hz Top Discharge Modular type cooling only Next Generation Variable Refrigerant Flow system, each Outdoor unit comprises of All 100% Inverter Driven Scroll Compressors, air cooled condenser with protective coated fins heat exchangement Corrosion fin factory coated ,Propeller type Fan with motor, Outdoor must be capable of working within Wide Range of Voltage fluctuation from 320V to 460V, auto addressing setting, refrigerant cooled PCB, electronic expansion valve, Outdoor mounting frame, microprocessor panel,subcooler, accumulator,isolating valve.VRF system shall be suitable for working on 54degree centrigrate. The unit shall be suitable for operation with R-410a refrigerant. Outdoor Unit only Cool. 28Hp VRF Out door Lifting / shifting at Ground Floor , Installation with Rubber ,Testing -Flushing with N2 & pre Commissioning . Out Door Unit VRF Outdoor Unit Installation Hard/Soft Copper Piping with 13mm/19mm Nitrile rubber insulation with fitting,support and brazed for suction and liquid line for VRF SITC of AHU Kit for Instalation of VRF Ducted as per OEM Design. Communication cable between Indoor & Out Door 2 x.75sqmm Cu Shielded Communication Cable with PVC insulated pipe. PVC Drain Piping with 6mm Nitrile rubber insulation. 25mm Dia 32mm Dia

Supply, installation, testing and commissioning of Air Conditioning system with Variable Refrigerant Flow system, comprising of the following: Supply of 415v - 3 Ph - 50 Hz Top Discharge Modular type cooling only Next Generation Variable Refrigerant Flow system, each Outdoor unit comprises of All 100% Inverter Driven Scroll Compressors, air cooled condenser with protective coated fins heat exchangement Corrosion fin factory coated ,Propeller type Fan with motor, Outdoor must be capable of working within Wide Range of Voltage fluctuation from 320V to 460V, auto addressing setting, refrigerant cooled PCB, electronic expansion valve, Outdoor mounting frame, microprocessor panel,subcooler,accumulator,isolating valve.VRF system shall be suitable for working on 54degree centrigrate. The unit shall be suitable for operation with R-410a refrigerant. VRF Indoor Unit Hi-Wall Units VHW. 1.5TR , 1.7TR, 2.0TR, 2.5 R, 2.8TR Cassette Unit VLC. 1.3TR , 2.3TR, 2.8TR VRF Ducted Unit 5.0TR, 6.0TR, 11.0TR Remote Controller Cordless Remote Corded Remote Y-Joint Refnet for Indoors Refnet for Outdoors VRF in door Lifting / shifting at Ground Floor , Installation with Rubber ,Testing -Flushing with N2 & pre Commissioning . Out Door Unit Cassette Machines Hi-Wall Units Ducted Unit 5TR/ 6TR & 11TR SITC of 120GSM, GI Ducting as per aprovall of Drawing. 24 Gauge 22 Gauge. Duct thermal insulation with 13mm thick nitrile rubber with out AL foil Faced. Duct accoustic insulation with 12 mm thick open cell nitrile rubber Al Powder Coated Diffusers / Grills with VCD Al Powder Coated Diffusers / Grills with Out VCD Duct Damper Refrigerant Gas-R410A Charging. Towards Charges for Commissioning of the system.

Supplying installation, testing, programming and commissioning of Audio equipment ON TABLE BOUNDARY MICROPHONE for any conferencing system: Frequency response 40 Hz – 20 kHz, Nominal impedance 200 Ω, Sensitivity 10 mV/Pa. Frequency Response :- 40 Hz - 20 kHz, Max. sound pressure level:- 140 dB, Sensitivity :- 10 mV/Pa, Dynamic range :- 111 dB (A) (Make:- Sennheiser/ Beyerdynamic/ Audio Technica)

Supply, Installation, Testing and Commissioning of DSP core with 16 user-configured card slots, Lua scripting engine, optional software-licensed HearClear AEC. (Make:- Xilica/ Biamp/ BSS)

Supply, Installation, Testing and Commissioning of Analog Input Card having 2 Mic/ Line Inputs. (Make:- Xilica/ Biamp/ BSS)

Supply, Installation, Testing and Commissioning of Analog Output Card having 2 Mic/ Line Outputs. (Make:- Xilica/ Biamp/ BSS)

Supply of Audio equipment,8" Open‐Back Ceiling Speaker. 70V/100V taps at 6W, 3W, 1.5W (plus 0.75W at 70V), very high 97 dB sense, 50 Hz to 16 kHz, for non‐plenum applications, 1.4 kg (3.0 l. (Make:- JBL/ Turbosound/ Bosch)

Supply, Installation, Testing and Commissioning of Eight-channel, 125W @ 4Ω Power Amplifier (Make:- Crown/ Labgruppen/ Behringer)

Supplying installation, testing, programming and commissioning of Audio equipment,50 cm Straight Line Array Column with 8 x 2” Drivers and Constant Beam width Technology, 20° vertical coverage, music (flat)/speech switch, 60W multi‐tap Transformer or 8 ohms, 80 Hz – 20 kHz, 150W cont pink (600W peak), wall bracket included (Make:- JBL/ Turbosound/ Tannoy)

Supplying installation, testing, programming and commissioning of Audio equipment, Dual Channel Power Amplifier, 550W@ 2ohm. 350 @ 4ohm, 215W @ 8 ohm per channel (Make:- Crown/ Labgruppen/ Behringer)

Supplying installation, testing, programming and commissioning of Professional 8-Channel 3-Bus Mic/Line Zone Mixer with Remote Control and Link Ports; 6 Ultra-low noise Mic/Line Inputs With Gain Control, -20 dB Pad, Level/Clip indicator, +48 V Phantom Power And Bus-assign Switches (Make:- Behringer/ Midas/ Yamaha)

Supplying installation, testing, programming and commissioning of Wireless hand held microphone system. (Make:- AKG/ Sennheiser/ Shure)

Supply and Installation of High flexible Speaker cable for power amplifiers upto minimum 500 Watt , Jacket - PVC, ø 0.32 in, black Conductor - Stranded bare copper wires, 140x35 AWG (13AWG) (Make:- Gotham/ Klotz/ Belden)

Supply and Installation of Audio Signal Cable;Balanced microphone cable with single shield, high flexible, velvet faint PVC-Jacket , Conductor: Stranded bare copper wires 28 x 0.10 mm (0.22mm²) , Jacket: PVC, 6.0 mm max. Ø (Make:- Gotham/ Klotz/ Belden)

Supply and Installation of Required Connectors like XLR, RCA, EP, Mono Jack, Stereo Jack, VGA Connectors, PVC Conduits and other accessories etc. (Make:- Amphenol/ Neutrik)

Supply and Installation of 10KVA Online UPS with 16 Nos SMF Batteries, Rack and Accessories. (Make:- Numeric/ Delta/ APC)

Supply, Installation, Testing and Commissioning of 85‑inch 4K Ultra HD HDR Professional Display. Display Device:- LCD, Backlight Type:- Direct (Full Array LED), Brightness (cd/m2) (*1):- 620 (Peak Brightness: 850 *1) , Contrast Ratio (*1):- 4000:1, Video Processing:- 4K X-Reality PRO, Wide Mode:- Auto/Wide Zoom/Normal/Full/Zoom, Viewing angle (Right/Left):- 178 (89/89) degree, Viewing angle (Up/Down):- 178 (89/89) degree. (Make:- Sony/ Panasonic/ Viewsonic)

Supply, Installation, Testing and Commissioning of Bracket for Display Panel (Make:- Lumi/ Play)

Supply, Installation, Testing and Commissioning of 55" 4K Ultra HD Commercial Display. Type/ Tech: "TFT LCD Module. IPS type, DLED backlight", Display Area (mm): 1209.6 (H) x 680.4 (V) (55” diagonal), Native Resolution: 3840 x 2160, Aspect Ratio: 16:9, Colors: 1.07B colors, Brightness: 400 nits (typ.), Contrast Ratio: 1200:1 Typ., Viewing Angles: H = 178, V = 178 typ. (Make:- Viewsonic/ Panasonic/ Sony)

Supply, Installation, Testing and Commissioning of POPUP BOX; Easy Access To Connectors Durable Pnematic Movementand Mechanical Latching Mechanism One Female 15pin HD Connector And 3.5mm Mini Stereo Audio Jack, Two CAT RJ45 network/data/phone Connectors, Two Unswitched AC Outputs, One HDMI (Make:- Magnum/ Extron/ Kramer)

Supplying installation, testing, programming and commissioning of Video equipment HDMI HDBaseT-Lite Extender (4K@40m)(HDBaseT Class B): Video: Max. Data Rate 10.2Gbps (3.4Gbps per lane) 10.2Gbps (3.4Gbps per lane), Max. Pixel Clock 340 MHz 340 MHz, Compliance HDMI (3D, Deep Color, 4K) HDCP Compatible, HDMI (3D, Deep Color, 4K) Max. Resolutions / Distance Up to 4K@35m (Cat 5e/6) / 40m (Cat 6a/ATEN 2L-2910 Cat6); 1080p@60m (Cat 5e/6) / 70m (Cat 6a/ATEN 2L-2910 Cat6) 4K supported: 4096 x 2160 / 3840 x 2160 @ 60Hz (4:2:0); 4096 x 2160 / 3840 x 2160 @ 30Hz (4:4:4) (Make:- Kramer/ Aten/ Extron)

Supplying installation, testing, programming and commissioning of 17U Floor Mount Racks: Basic Frame Steel; Construction Welded; Top & Bottom Cover Welded to Frame with Cable entry exit cut outs; Front Door Lockable Toughened Glass Door; Rear Door Lockable Steel Door; 19” Mounting Angle Formed Steel; Std. Equipment Mounting DIN Std. 10mm Sq. Slots; Standard Finish Powder coated; Standard Colour Grey & Off White OR Black; Standard Mounting Caster wheels (2 with Brake & 2 without Brake); Rack Standard Conforms to DIN 41494 or equivalent standard (Make:- Valrack/ Nettrack/ APW)

Supply, Installation, Testing and Commissioning of 8x1 HDMI Switcher. Max. Data Rate - 6.75Gbps (2.25Gbps per graphic channel), HDMI Support - Deep Color, x.v.Color™, Lip Sync, HDMI Uncompressed Audio Channels, Dolby TrueHD, DTS−HD, CEC. 3D Pass-Through, RESOLUTION: Up to UXGA; 1080p, deep color. POWER CONSUMPTION: 100−240V AC, 50/60Hz, 12VA. (Make:- Kramer/ Aten/ Extron)

Supply and Installation of 10 mtr High-performance Cables With Molded HDMI Connectors At Both Ends. HDMI Standard Supports High-definition Video Plus Multi-channel Audio In A Single Cable. (Make:- Kramer/ Aten/ Belden)

Supply and Installation of 1 mtr High-performance Cables With Molded HDMI Connectors At Both Ends. HDMI Standard Supports High-definition Video Plus Multi-channel Audio In A Single Cable. (Make:- Kramer/ Aten/ Belden)

Supply and Installation of Shielded Cat 6 Cable (Make:- Molex/ Dexathron)

Supply and Installation of RJ45 Connector (Make:- Molex/ Dexathron)

M/S SUNRISE ENTERPRISE