DAY TO DAY COMPREHENSIVE MAINT OF BS MARG MD ACCN INCL BR AND EM FITTINGS FIXTURES ALONGWITH CLEANING OF MANHOLES SEPTIC TANKS AND SEWAGE LINE UNDER GE EAST LUCKNOW

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm thick above or below ground level complete all as specified and directed

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).complete all as specified and directed

Forming construction joints 30 mm deep x 10mm wide filled with sealing compound grade "A."complete all as specified and directed

M&L for 40mm thick cement concrete 1:2:4 type B-1using 20mm graded aggregate as in floors, surface finished even & smooth using extra cement complete all as specified and directed.

M&L for 50mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floor surface finished even and smooth without using extra cement complete all as specified and directed.

Taking down of cement plaster in any description on brick or stone wall etc, incl racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering, 15mm thick on fair faces of brick work or on concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering, 15mm thick on otherthan fair faces of brick work or on concrete surfaces in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound of approved make complete all as specified and directed.

M&L for rendering, 5mm thick on fair faces of brick work or on concrete surfaces/ceiling in CM 1:3 finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered surface of Ceiling and applying thee coats of white wash in any height of building complete all as specified and directed.

M&L for preparation of new plastred surfaces of wall and applying three coats of cement base paint of approved shade/ tint, complete all as specified and directed.

M&L for Preparation Newly plastered sur faces as in Wall surface and appling two coat of distemper oil emulsion, over a coat of Priming coat with alkali resistant priming paint over a coat of primer birla white care Putty over plastered surface to prepare the surface even and smooth.complete all as specified and directed

S&F in repairs vitreous china squatting pan "Orissa" pattern size 580mmx440mm white with integral foot rests including connection to trap, and to flushing pipe, anti syphonage pipe, etc complete making good to floors and complete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white (excluding flushing cistern and flush pipe) including connection to drain or out going pipe and flush pipe anti syphonage pipe etc complete all as specified and directed

S&F in repair for plastic water closet seat cover , white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

S&F in repair viterous china Wash Hand Basin white flat black type of size 550x400mm including cutting for and pinning in ends of brackets and fixing in walls including 32mm dia chromium plated waste fittings/coupling, PVC waste pipe MS brackets complete all as specified and directed.

S&F as in repair PVC valve less, syphonic action type flushing cistern, ISI marked, 10 lit capacity, low level white with inlet, ball valve , float and handle including brackets and flush pipe fixed etc complete all as specified and as directed.

S&F in repair vitreous China Urinal, bowl type (back or corner wall type) size of 465x355x265mm white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinalto plugs with and including 60 mm long brass screws, pointing around urinal back in cement, complete all as specified and directed.

S&F steel water tubes medium grade, galvanised with all fittings 15mm bore fixed complete to concilled in walls and ceiling or laid in floors including taking up or down steel tubing and connections, 15mm bore complete all as specified and directed.

S&F steel water tubes medium grade, galvanised with all fittings 20mm bore fixed complete to walls and ceiling or laid in floors trenches including taking up or down steel tubing and connections, 20mm bore complete all as specified and directed.

S&F, in repair for waste coupling, brass, chromium plated for basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed 32mm bore, complete all as specified and directed.

S&F, in repair 32 mm bore Low density PVC flexible pipe for Wash hand basin/sink etc complete all as specified and directed.

S&F, in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed

S&F in repair stainless steel sink coupling size 75/100mm dia complete all as specified and directed.

S&F in repair CP grating with or witout waste hole size 100 mm fixed with white cement in tiles flooring complete all as specified and directed.

S&F in repair PVC (SWR) floor trap of size 110/110mm, complete all as specified and directed.

S&F in repair for 110mm PVC (SWR) WC connector bent type, complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) bend, any radius, complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) bend, any radius, complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) vent cowl, complete all as specified and directed.

Cleaning and removing all scale and dirt etc from tank and from mouth of circulating pipe etc of capacity exc 250 n exc 500 ltrs complete all as specified and directed.

S&F for 500 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I and including dismantling of old existing tank, complete all as specified and directed.

S&F, in repair 20mm dia float valve high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipe with fly nuts complete all as specified and directed.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe of 20 mm bore complete all as specified and directed.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe of 15 mm bore complete all as specified and directed.

Cutting chases pining in brick, concrete walls built in cement mortar or cement lime mortar making good to facings where required and pointing in cement mortor 1:3 to ends or edges of shelves lintels etc and cutting chases for concealed water tubing cutting not exc 10 cm girth all as spcefied and directed.

S&F in repair 15mm bore angle valve /stop valve chromium plated fency type.cast copper alloy screwed down high pressure, crutch or butterfly handle, ,screwed both end for pipe or for unions complete all as specified and directed.

S&F, in repair, 15mm dia long body bib taps, cast copper alloy chromium plated fancy type with crutch or butterfly handle sc-rewed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair 15mm dia spindle for bib taps,angle valve and pillar taps as required as per sample given by Engr-in-Charge, complete all as specified and directed.(Including taking down existing spindle carefully and fixed the same in position).complete all as specified and directed

S&F in repair stop valves, 15mm dia, cast copper alloy, CP fancy type with long shank and cup (concealed type) screwd down, high pressure with crutch or butter fly handle,screwed both ends for iron pipes or for unions complete all as specified and directed.

S&F in repair kitchen sink with drainage board made of stainless steel 0.80 mm thick with plug washer and waste including bedding in cement mortar including fixing cantilever bracket and connecting union to pipe overall size 915 X 460 mm bowl size 410 X 330 X 160 mm complete all as specified and directed.

S&F, in repair 32 mm bore Low density PVC flexible pipe for Wash hand basin/sink etc complete all as specified and directed.

S&F in repair CP Shower rose with arms 15mm dia complete all as specified and directed.

S & F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F, in repair Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed 32mm bore, complete all as specified and directed

S&F in repair, PVC (SWR) floor trap, plain with grat-ing including joint-ing with solvent cement (Diameter of outlet 75mm) complete all as specified and directed

S&F in repair, CP grating with waste pipe hole 100 mm dia, complete all as specified and directed.

S&F in repair sheet glass shelf assemble consisting of 5.5 thick sheet glass shelf 12cm wide with CP bracket gaurd & railing 60cm long complete all as specified and directed

S&F, in repair brass chromium plated, tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed

S&F, in repair, 15mm dia two way bib taps, cast copper alloy chromium plated fancy type handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for glazed ceramic joint free coloured tiles in vertical surfaces 600x300x7mm thick, set and joiunted in neat cement slurry and pointed in coloured cement to match over and including 10mm thick screed bed in cement mortar 1:3 complete all as specified and directed.

M&L for coloured Non Skid ceramic jointless tiles 7 -8mm thick (square/rectangular) are of each tile exc 0.11 Sqm but not exc. 0.18 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed or bedding layer with CM 1:4 complete all as specified and directed.

M&L for non skid ceramic (coloured) jointless tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.18 sqm but not exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match coloured tiles over and including 15mm thick screed CM 1:4 complete all as specified and directed.

M &L for Welding in repair thickness of metal to be welded exc 20mm but nexc 25mm size of length exc 2.5 cm but n exc 5 cm in length complete all as specified and directed

M&L for 25mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in leveling course to floor as in roof padding , benching existing roof slab laid to slope as existing complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm including dismantling of existin fram ( exc 1 sqm but not exc 2.25 sqm) and up to 02 stroried height and re-fixing the same with holdfast and flat iron with necessary welding/reveating fixed with alluminium wire staples including taking down from any section and refixing with new wire mesh with tinned tack/by welding/bolting/beading.complete all as specified and directed

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm including dismantling of existin fram ( not exc 1 sqm) and up to 02 stroried height and re-fixing the same with holdfast and flat iron with necessary welding/reveating fixed with alluminium wire staples including taking down from any section and refixing with new wire mesh with tinned tack/by welding/bolting/beading.complete all as specified and directed

S & F for mild steel framed work as in doors/window flat iron or gates of angle or other section drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and stainless steel hings, Fe-410W (Gde-E-250) quality-A, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area n.exc 1.50 sqm each, and removing from site, complete all as specified and directed

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exc 1.5 Sqm but not exc 4 Sqm each and removing from site complete all as specified and directed

Taking down shutters of any description area n exc 1.00 sqm each and removing from site complete all as specified and directed

Taking down shutters of any description exc 1.00 sqm but not exc 2.00 Sqm each complete all as specified and directed

M&L for plain cement concrete cast in situ Type B1 1:2:4 (20 mm graded aggregate) as in copings, hold fast, back filling of pressed steel frame and other similar work water troughs and the like including weathering, slightly rounded or chamfered angles and throating etc including form work complete all as specified and directed

S&F for MS hold fasts; supports or stays for rainwater, knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe -290 code E-165 all as specified and directed.

S&F for 30mm thick factory made flush shutters solid core construction with block board core and ply wood face panels, commercial type on both sides, complete all as specified and directed.

S & F for 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed

S&F for factory made solid PVC door frames of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed

S & F for factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M. S. tubes for top & bottom rails. M. S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, in the frame complete all as specified and directed

S&F for steel windows with side hung shutters including projection type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed and welded, complete all as specified and directed.

S&F for steel windows with side hung shutters including projection type hinges with steel handle, and steel peg stay complete without glazing bars, dovetailed and welded, complete all as specified and directed.

S&F for steel ventilator with top hung shutter including box type hinges, peg stay and glazing bars complete with dove tailed or welded, complete all as specified & directed.

M&L for 18-19 mm thick block boards, grade 1 quality, exterior grade, commercial type, fixed with screws to timber frame-work, complete all as specified and directed.

M&L for 0.90mm thick decorative laminates 'Mica type 1 of surface finished,colour and pattern as approved, fixed with adhesive as per makers instructions.complete all as specified and directed

M&L for 6mm thick external teak wood lipping for block board or veneered particle board , fixed with nails, complete all as specified and directed.

M&L for 19/20 mm thick prelaminated particle board, exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work fixed as in repairs, complete all as specified and directed.

S&F in repairs, CP curtain rods 22 - 25 mm dia with and including fixing of two Nos MS brackets and decorative type PVC knobs at both ends of curtain rod complete all as specified and directed

S&F for 150mm size stainless steel, fancy type handle fixed with screws complete all as specified and directed.

S&F magnet catcher for cup board shutter fixed with screws complete, all as specified and directed.

M&L for 2nd class hard wood, wooden beading, plain fillets, square or rectangular or tringular in section clean sawn sectional area exc 3 sqcm but not exc 6 Sqcm fixed with nail complete, all as specified and directed.

M&L for 2nd class hard wood, plain fillets, square or rectangular or tringular in section clean sawn sectional area not exc 3 sqcm fixed with nail, complete, all as specified and directed.

S & F, 100 mm size butt hinges, medium weight, stainless steel, and fixed complete all as specified and directed

S & F in repair 100 mm size butt hinges, medium weight, stainless steel, and fixed complete all as specified and directed.

S&F in repair 150mm long aluminium handles cast type, anodised, complete all as specified and directed.

S&F, 200 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed

S&F in repair 200 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed

S&F for aluminium alloy, anodized, sliding door bolt, 300mm long, with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section or cast aluminium alloy & fixed.complete all as specified and directed

S&F in repairs aluminium alloy, anodized, sliding door bolt, 300mm long, with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section or cast aluminium alloy & fixed.complete all as specified and directed

S&F for 150 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F in repairs 300mm long mild steel ordinary rat tail rod pattern springs including roller & roller plate complete all as specified & directed (Fixed as in Existing iron /wooden frame in own arrangement).

S&F, 125 mm size hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in repair 125 mm size hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Hacking out old brokon glass (any thickness, size, quality or description ) from wooden or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

S&F of 3.00 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed.

S&F in repair of 3.00 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed.

S&F of 4.00 mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane, complete all as specified and directed

S&F for stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with alluminium wire staples, complete all as specified and directed.

S&F in repair for stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with alluminium wire staples, complete all as specified and directed.

S&F for 140mm long floor door stopper of aluminum alloy body & tongue, anodized, with hard drawn steel spring, fixed in floor complete all as specified and directed.

M&L for petty repair to Anodised aluminium frame or shutter in doors, windows, ventilators including joining cleat, glazing clips, ruber neoprene packing, handles , hinges, anodised aluminum snap beading screws etc for refixing in same opening etc but excluding wire mesh and glass pane measured saperately complete all as specified and directed

M&L for prepration of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description over 10cm width or girth complete all as specified and directed.

M&L for preparation of newly steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on surfaces of any description over 10 cm width or girth, not oterwise described, complete all as specified and directed.

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate in Surface channel or drains including necessary form works , stops ,moulds etc complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including necessary forms mould mitred /stopped ends etc complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for brick work with fly ash bricks old size, straight or curved on plan exc. 6.0M mean radius, built in cement mortar 1:6 complete all as specified and directed.

All as per Item No 109 above but except bricks. (Bricks recd from demolition) complete all as specified and directed

M&L for brick work with fly ash bricks, old size, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in cover slab, shelves and similar articles set in CM 1:4 complete all as specified and directed. Note:- Reinforcement shall be measured & paid separately.complete all as specified and directed

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar works; not exceeding 200mm thick (horizontal or sloping) complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floors & roofs n exc 20cm wide & sides of RCC/PCC bands in walls, horizontal or sloping, & similar work exc 10cm but exc 20cm wide complete all as specified and directed

M&L for TMT bars 10mm dia and over cut to length, bent to shape required including cranking and binding with Mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

All as per Item No 116 above but 6mm to 8mm dia ditto.complete all as specified and directed

All as per item No 116 above but 5mm dia and over upto and including 10 mm dia in stirrups,apacers and binders -do-.complete all as specified and directed

M&L for RCC 1:1.5:3 (Nominal Mix) using 20 mm graded stone agg as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

Demolition and breaking up drain pipes (SGSW, AC or RCC) of 150mm bore sizes, set in cement mortar complete all as specified and directed.

M&L for salt glazed stone ware drain pipe grade A 150 mm internal dia (ISI marked) laid in trenches and jointed in cement mortar (1:1) and tested complete all as specified and directed.

S&F for 150mm inner dia reinforced concrete pipes, class NP-2, laid nd jointed complete with collers, complete all as specified and directed.

M&L for cement concrete type C2 (1:3:6) with 100 mm thick bedding to drain pipes of 150 bore sizes including packing under and hunching against the sides of pipes after they are laid and tasted; in cement concrete complete all as specified and directed.

Excavation in trenches n. exc 1.5 m wide and not exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier hole etc not exc 10 sqm on plan and not exc 1.5 m depth and getting out in soft/loose soil complete all as specified and directed.

Returning filling in trenches including spreading leveling, watering and well ramming in layer not exc 25 cm thick complete all as specified and directed.

Removing of excavated materials to a distance 1.5km and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching complete all as specified and directed.

Taking down rain water pipes (any size or pattern) incl all fittings, shoes, bends, swan neck etc complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to wall incl MS holding clamps complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to wall incl MS holding clamps complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore of pipe etc complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 75 mm bore of pipe etc complete all as specified and directed.

S&F of 110mm bore PVC (SWR) bends,any radius with access door complete all as specified and directed.

S&F of 75mm bore PVC (SWR) bends,any radius with access door complete all as specified and directed.

Dismantling of stone slabs and tiles laid dry of any description or thickness in floor, aprons etc complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block, ruberised, glossy finish any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment complete all as specified and directed.

M&L for sand under floor or paving laid in layers not exc 15cm thick, spread, levelled and rammed complete all as specified and directed.

Dismantling fencing post or struts (wood , steel or RCC ) of any size and any description including taking out embeded portion and making good disturbed ground complete all as specified and directed

Dismantling of chain link fencing of any description complete all as directed

Excavation in post hole (or similar hole) each n exc 0.50 cum, getting out returning filling in and ramming earth or broken rubble mixed with earth around in layer n. exc 25 cm etc and getting out soft/ loose soil complete all as specified and directed

M&L for PCC 1:3:6 type B2 using 40 mm graded stone aggregate as in foundations filling and mass concrete filling, etc complete all as specified

S&F for mild steel work as in posts and struts etc in fencing including cutting tops to shapes as directed, drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165 complete all as specified

S&F mild steel framed work as in doors / gates / steel frames / chowkats etc. of angle or other section with gusset plates, rails, braces, etc., complete conforming to Grade E - 410 (Fe 250), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position complete, all as specified & directed.

S&F in repair galvanised two strand steel barbed wire with 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rail strain-ing bolts including, securing or tying at crossing with and provision of galvanised mild steel wire, staplesor steel pins, etc. complete all as specified and as directed .

Supply only Chain Link MS galvanized fencing of any size and any type as approved complete all as specified and directed

Fixing Only Chain Link fencing including line wires, any mess, size and type to any type of standards, rails, straining bolts, etc including provision of binding wires, complete all as specified and directed

M&L for two coats of synthetic enamel paint over a coat of Red oxide primer surfaces including preparation of surfaces complete all as specified and directed

Dismantling of Trellis work (Jafri)/RCC jali complete all as specified and directed

M&L for Providing precast cement concrete type B-O using 12.50 mm graded stone aggregate louvres and jallies set in CM 1:4, 35mm thick (measured solid), including all mould- ings but excluding frame complete all as specifed and as directed.

M&L for factory made RCC man hole cover /drain cover with cover frame comprising of 75mm thick cover, including provision of hot dip galvanized lifting hook for lifting overall cover with suitable size angle iron frame, RCC cover of M-30 grade concrete by vibro compression process, medium duty confirming to IS-12592 including fixing on manhole, demolition of existing coverwith cover frame and removal of debris from site complete all as specified and directed. Note : The factory made RCC cover shall be ISI marked and as approved.

Removal of debrish exc. 1.50 km but not exc. 5 km and depositing where directed at a level complete all as specified and directed.

Dewatering of soak well , septic tanks by using mechanical pump diesel driven with fuel operator and crew of water etc at site complete all as specified and directed by Engineer in charge.

Cleaning of soak well, septic tanks by way of desludging foreign material manually/mechanically and removal of sludge/silt/liquid mud sand (in foul conditions) etc, and disposed off outside of MOD premises (at the location notified by the local Municipal Corporation/ Cantt board as per rules of public health), including digging required nos of pits for depositing sludge and future capping the pit with the 25 cm thick layer of soil and sprinkling bleaching powder (including supply of bleaching powder) over the area of ditches with one metre around complete all as specified and directed.

Cleaning of blockage of 150mm bore sewer lines (i.e. branch sewer line, main sewer line) by way of cleaning desludging foreign material as well as roding of sewer line between successive manholes manually/mechanically or pumping out sewage from blocked line including desludging where required and ordered by Engineer-in-Charge and keeping sewer line functional from Ist manhole upto final drop as septic tank, soakage well all as specified and directed .

Cleaning of all manholes upto 3.00 meter depth of any size and removal of sludge/silt/liquid mud sand (in foul conditions) etc, and disposed off out of MOD premises (at the location notified by the local Municipal Corporation/Cantt board) (as per rules of public health), including digging required nos of pits for depositing sludge and furture capping the pit with the 25 cm thick layer of soil and sprinkling powder ( including supply of bleaching powder) over the area of ditches with one metre around complete all as specified and directed.

Cleaning of all manholes upto 1.5 meter depth of any size and removal of sludge/silt/liquid mud sand (in foul conditions) etc, and disposed off out of MOD premises (at the location notified by the local Municipal Corporation/Cantt board) (as per rules of public health), including digging required nos of pits for depositing sludge and furture capping the pit with the 25 cm thick layer of soil and sprinkling powder (including supply of bleaching powder) over the area of ditches with one metre around complete all as specified and directed.

Cleaning of all blockages of Nahni traps/floor traps/bottle traps, blockages of WC's, upto 1st manhole/Gully Trap in shafts, vertical CI soil/waste pipe stacks, CI Tee/door bends etc & cleaning of drain pipes of any dia by rodding and removal of sludge/silt/liquid mud sand (in foul conditions) etc, out of MOD premises (at the location notified by the local Municipal Corporation/Cantt board). To Maintain of internal & external sewage system in functional state at all the time by engaging/deploying minimum One Safaiwala alongwith one Helper from 0900 hours to 1700 hours at Complaint cell of AGE B/R-II area mentioned in the contract on daily basis, with manual/ pressure cleaning pump and flexible rods and other necessary equipments (as per rules of public health), complete all as specified and directed.

Note for item no-153 to 157 1.The cleaning shall be carried out with mechanized operation by means of diesel / electric operated vehicle mounted hydraulic operated high pressure suction -cum -jetting machines fitted with pump of required capacity and the sludge sucked out with Super Succer Machine of required capacity and sent to storage tanks for further disposal to the authorised disposal site land at any distance and without any additional cost. 2. The sludge deposited in sewage line shall be fully cleaned and disposed off the same outside the MOD land at any distance and without any additional cost , on the same day when it was taken out.The job shall be carried out with safety precaution equipment and with strict supervision . 3. During the mechaized operation , the service provider /Contractor shall be equiped with Gas monitor , nylon rope ladder , torch light and compressor blower etc along with the sewage cleaning truck mounted suction / jetting machine . 4. The unit rate quoted by the contractor shall interalia deemed into the cost of providing skilled driver and operator and supervising engineer including provision of water for jetting & removal of sludge /silt /liquid /mud & sand (in foul position )etc. 5. The contractor shall engage the above mentioned T & P and intimate to Enginner - In -Charge in writing with Machine No./ Vehicle No. etc for their record and prior approval . 6. A Register shall be maintained showing the Machine No /Vehicle No. and their deployment at site mentioning time and date duly sighned by concern JE , Engr -in- charge and contractor and the same register shall be produced while claiming the payment by the tenderer .

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc for taking credit including making good the disturbed surfaces to match with the existing complete all as specified and directed.

Material and labour for one light / fan point controlled by one, one way switch 06 Amp wiring with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement of sunk zinc coated pressed steel terminal box of 1.60 mm thick with 3 mm thick plastic laminated sheet top cover, brass screws, cup washers etc and making good to the disturbed surfaces to match the existing complete all as specified and directed.

All as per serial item No 160 here-in-before but one bell point controlled by one bell push, 06 Amp.complete all as specified and directed.

All as per serial item No 160 here-in-before but one, two way light point controlled by two, two way switches, 06 Amp.complete all as specified and directed.

All as per serial item No 160 here-in-before but one 3 pin, 06 Amp socket outlet point on independent board controlled by one, one way switch 06 Amp.complete all as specified and directed.

All as per serial item No 160 here-in-before but one 3 pin, 06 Amp socket outlet point on same board controlled by one, one way switch 06 Amp.complete all as specified and directed.

All as per Serial Item No 160 here-in-before but point wiring with 2.5 Sq mm single core FRLS cables and earth continuity wire of 1.5 Sq mm single core FRLS cable for one 3 pin 16 Amp socket out let point controlled by one, one way switch on independent board complete all as specified and directed.

Material and labour for one light / fan point controlled by one, one way switch 06 Amp wiring with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement of sunk zinc coated pressed steel terminal box of 1.60 mm thick modular type ( excluding rate of metal box mesurement seprately) etc and making good to the disturbed surfaces to match the existing complete all as specified and directed.

Supply and fix in replacement switch piano flush type, 06 Amp, single pole, one way, 230 Volt complete all as specified & directed.

Supply and fix in replacement switch piano flush type, 06 Amp, single pole, two way, 230 volt complete all as specified & directed.

S&F in replacement Calling bell , AC, 230 Volts, single phase complete all as specified and as directed

Supply and fix in replacement bell push, flush type, 06 Amp, 230 volt complete all as specified & directed.

Supply and fix in replacement socket outlet 2 in 1, 5 pin, 06 Amp, flush type, 230 volt complete all as specified & directed.

Supply and fix in replacement switch socket combination outlet 2 in 1, 3 pin, 06 Amp and 16 Amp flush type, universal, 230 volt, four hole complete all as specified & directed.

Supply and fix in replacement electronic ceiling fan regulator with rotary step, two module, humfree, AC, 240 volt, 100 Watt and duly ISI marked complete all as specified & directed.

Supply and fix in replacement lamp holder, PVC / Polycarbonate type with back plate suitable for batten fitting complete all as specified & directed.

Supply and fix in replacement of decorative wall mounting type LED light fitting, 1 x 15 Watt, 230 Volt made up of Polycarbonate including shade, lamp holder, 9/10 Watts LED lamp B22 CDL etc and all accessories pre-wired including connecting up complete all as specified and directed.

Supply and fix in replacement of integrated LED bulk head fitting 10 Watt, 6500K with IP 65 protection comprises of high pressure die cast aluminium housing, polycarbonate cover, etc complete all as specified and directed.

Supply and fix in replacement LED tube light fittings 1200 mm, 22 W higher energy saving decorative ultra slim square profile LED lighting fixture with extruded aluminium housing without powder coating enviromental friendly, energy efficient complete all as specified and directed.

Supply and fix in replacement LED tube light fittings 600 mm,10/12W higher energy saving decorative ultra slim square profile LED lighting fixture with extruded aluminium housing enviromental friendly, energy efficient complete all as specified and directed.

Supply & fix in replacement LED wall/surface mounted down lighter, 12 W including electrical connection with PVC three core copper flexible wire & all necessary fixing accessories complete all as specified and directed

Supply and fix in replacement ceiling rose, 6 Amp, 250 volt, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body of 50 x 25 mm size complete all as specified & directed.

Material and labour in replacement sub main wiring with 06 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 06 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

Material and labour in replacement sub main wiring with 04 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 04 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

Supply and fix in replacement of industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB, SP, AC, 240 volt of 20 Amp, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

Supply and fix in replacement of sheet metal enclosure distribution board, double door, single pole and neutral, AC, 240 volt, 08 way, with 200 Amp rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

Supply and fix in replacement of sheet metal enclosure distribution board triple pole and neutral (VTPN),double door, AC, 440 volt, 04 way with 200 Amp rated copper bus bar and metal door with IP 54 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed and comprising of the following:- (a) MCCB, 125 Amp, 04 pole, AC, 415 Volt of 16 KA breaking capacity complete - 01 No. (b) MCB, SP, AC, 240 volt of 06 to 32 Amp, "C" curve, 10 KA breaking capacity - 12 Nos.

Supply and fix in replacement of MCB, DP, AC, 240 volt of 40 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fix in replacement of MCB, DP, AC, 240 volt of 63 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fix in replacement of MCB, SP, AC, 240 volt of 06 to 40 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fix in replacement of MCB, DP, AC, 240 volt of 32 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Material and labour for earthing complete with galvanised mild steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level steel earth plate connected with GI wire 04 mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15 mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150 mm thick around GI earth plate, GI pipe medium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6 mm dia at the rate of 75 mm centre to centre both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40 mm x 40 mm x 3 mm frame for pit cover including testing on completion complete all as specified and directed.

Supply & fix LED in replacement Ceiling /surface mounted down lighter warm / white colour,18 watt round/ squre profile , 18 W including electrical connection with PVC three core copper flexible wire & all necessary fixing accessories complete all as specified and directed

S&F in replacement of LED post top lantern 35 Watts with symmetric light distribution energy saving, environmental friendly IP65 spun aluminium landscape luminiary with higher power LED as light source complete all as specified and directed .

Supply and fixing in replacement LED Bldg security light fitting LED 45 watt with SPD, PF not less or equal 0.9,epoxy coated cover sheet aluminium housing with heat resistant toughtened glass & IP 66 incl with bracket, clamps, nuts, bolts protection complete all as specified and directed

Supply only in replacement LED bulb 9/10 Watts suitable for B22 white in colour complete all as specified and directed

S&F in replacement PVC casing n caping ISI marked of size 20mm.complete all as specified and directed.

S&F in replacement PVC casing n caping ISI marked of size 25mm.complete all as specified and directed.

S&F in replacement rigid non-metallic PVC conduit of size 20mm.complete all as specified and directed.

S&F in replacement rigid non-metallic PVC conduit of size 25 mm.complete all as specified and directed.

S&F in replacement Flexible conduit of size 20mm.complete all as specified and directed.

S&F in replacement Flexible conduit of size 25 mm.complete all as specified and directed.

S&F in replacement PVC gang box suitable for 6 Amp Socket and 6 amp switch..complete all as specified and directed.

S&F in replacement PVC gang box suitable for 16 Amp Socket and 16 amp switch.complete all as specified and directed.

QUALITY CONSTRUCTIONS CO

KUMAR ENTERPRISES