Special repair to Bldg No T-212, T-213, T-217 and T- 219 ( Water Supply Stores) under GE (N) Bikaner at Mil Stn Bikaner

Amount

Demolition of cement concrete in ground floor and paving not exc. 15cm thickness (below or above GL) complete all as specified and as directed by Engineer-in-Charge.

Dismantling existing terrazo dado /flooring or tilles in hearth or wall tiling, bathroom, WC and kitchen etc, including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engineer-in-Charge.

Dismantling Asbestos cement sheet , any thickness (corrugated, semi corrugated etc) sheets in roof coverings including ridges complete all as specified and as directed by Engineer-in-Charge.

Dismantling Plain or corrugated steel sheeting any guage, any thickness (corrugated, semi corrugated etc) sheets in roof coverings including ridges complete all as specified and as directed by Engineer-in-Charge.

Dismantling timber in fillets, rails, posts, rafters, purlins, etc under 40 Sqcm in section, in unframed work in any position complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhats or frames not exc. 1.50 Sqm each but with shutter (w/o taking of shutter from the frame ) complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhats or frames exc. 1.50 Sqm each but n.exc. 4sqm each with shutter (w/o taking of shutter from the frame ) complete all as specified and as directed by Engineer-in-Charge.

Dismantling of Roof tiles of any description or thickness in floor, apron etc laid, bedded and pointed in cement mortar complete all as specified and as directed by Engineer-in-Charge.

Demolition of lime concrete of any description over roof slab complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick work built in cement mortar including all quions arches pillars etc, complete all as specified and as directed by Engineer-in-Charge.

Dismentling of stone patti as in roof slab of any description and thickness, complete all as specified and as directed by Engineer-in-Charge.

Taking down cement plaster/terrazo finish on brick or stone walls incl. raking out joints hacking for key scrubbing down with water etc, complete all as specified and as directed by Engineer-in-Charge.

S & F Mild Steel work in structure/tublar trusses incl spl shaped washer etc using ERW or induction buttt welded tubes conforming to IS 1161-1979 grade st-240, complete all as specified and as directed by Engineer-in-Charge.

S & F Mild steel screw bolts(machine made) square head at one end screws on other for washer and nut n exc. 5cm long with dia of neck exc 12mm complete all as specified and as directed by Engineer-in-Charge.

S & F MS plates/flats angle etc as in cleat gusset , steel doors incl drilling welding etc ,complete all as specified and as directed by Engineer-in-Charge.

M&L for PCC 1:2:4 Type B1 (using 20mm graded stone aggregate) as in bands, plinth course, parapets and raillings kneelrs apex stone bed plates, kerbs stones, kerbs and the like including weathering slightly rounded or chamferd angles and throating as directed by Engr-in-charge.

S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mps as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge.

S & F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mps as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge.

M& L for brick work with sub class B bricks straight or curved on plan exc 6m mean radius brick walls built in CM 1:6 complete all as specified and as directed by Engineer-in-Charge.

M&L for brick work with sub class B bricks straight or curved on plan exc 6m mean radius as in half brick walls built in CM 1:4 complete all as specified and as directed by Engineer-in-Charge.

M&L for Rendering 15mm thick cement plaster on fair faces of brick or conc. Surfaces in cement mortar 1:4,even and smooth w/o using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for Rendering 15mm thick cement plaster on fair faces of brick or conc. Surfaces in cement mortar 1:6,even and smooth w/o using extra cement complete all as specified and as directed by Engineer-in-Charge. .

M&L Rendering 10mm thick on fair faces of conc. Surfaces in cement mortar 1:3, even and smooth w/o using extra cement as on ceilingc complete all as specified and as directed by Engineer-in-Charge.

M&L for 10 mm thick Rendering in cement mortar 1: 4 on concrete surfaces, finished Fair & even including mixing water proofing compound as per manufacturer's instns( WPC to be measured separately as supply only)

Supply only water proofing compound, ISI marked, complete all as specified and as directed by Engineer-in-Charge.

M&L for polythene film black 150micron thick complete all as specified and as directed by Engineer-in-Charge.

M&L Applying evenly a tack coat of industrial bitumen 85/25 ,1.2kg/sqm incl cleaning surface complete all as specified and as directed by Engineer-in-Charge.

M&L Lime concrete terracing as specified on roof complete all as specified and as directed by Engineer-in-Charge.

M&L 40 mm thick Brick tiles bedded in 15 mm thick cement and sand mortar (1:6) and joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed by Engineer-in-Charge.

M and L for Galvanised wire cloth 0.56mm nominal dia of wire and avg.width of aperture 1.18mm fixed with tinned tacks or galvanised wire staples complete all as specified and as directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips including providing and fixing new ones complete all as specified and as directed by Engineer-in-Charge.

M & L for sheet glass 3mm thick ordinary quality and glazing with oil putty in square not exc.0.5sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

S&F Steel window with side hung shutter incl.box type hinges with steel handle of MS flat 25x5mm and 2nos tower bolt of 100mm long fixed to shutter complete with glazing bar dovtailed or welded including one shop coat of primer complete all as specified and as directed by Engineer-in-Charge.

S&F Steel window with side hung shutter incl.box type hinges with steel handle of MS flat 25x5mm and 2 nos tower bolt of 100mm long fixed to shutter complete without glazing bar dovtailed or welded including one shop coat of primer complete all as specified and as directed by Engineer-in-Charge.

S&F Steel ventilators with top hung shutter including hinges, steel peg stay , complete all as specified and as directed by Engineer-in-Charge.

S&F Mild steel framed work such as grills ,framed guard bars barred iron doors ; ladders framed balusters railings and similar work conforming to Fe 410-0or Fe 310-0 complete all as specified and as directed by Engineer-in-Charge.

M&L 20-25 mm thick machine cut kota stone slab in flooring etc., laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing and also including rounding off outer exposed edges and also including laying over and 15 mm thick screed bedding in cement and sand mortar 1:6 complete incl roughining the surface complete all as specified and as directed by Engineer-in-Charge.

M&L 15-20 mm thick machine cut kota stone riser to steps, skirting,dado and pillar etc on vertical surfaces laid over 15 mm thick cement plaster in cement and sand mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade including rubbing and mirror polishing complete incl roughining the surface complete all as specified and as directed by Engineer-in-Charge.

M & L PCC 25mm thick 1:2:4 type B0 (12.50 mm graded aggregate) in any position in ground floor/roof complete all as specified and as directed by engr-in-charge.

Raking out joints/pointing to brick work or stone patti ceiling laid flat in lime concrete complete all as specified and as directed by Engineer-in-Charge.

M&L for flush pointing in cement mortar 1:3 on ceiling surfaces of stone patti roofs complete all as specified and as directed by Engineer-in-Charge.

M&L for 40-50mm thick Bhilwara sand stone slab not exc 2mtr in length, punched dressed self faced set and pointed in CM 1:4 as in Chhajja's, shelves and cills, plinth etc. complete all as specified and as directed by Engineer-in-Charge.

M & L 10cm thick sand stone slabs in roof slab, shelves ,chajjas etc n.exc 2m in length set and pointed in CM 1:4 complete all as specified and as directed .

PCC 1:3:6 type C-1 using 20mm graded stone agg. ,50mm thick as in floors over stone patti roof slab finished the surface even and fair complete all as specified and as directed .

M&L for 75mm thick cement concrete 1:3:6 type C-1 using 20mm graded agg stone as in plinth protection and finished even & fair ,filling mastic asphalt in joints complete all as specified and directed.

M & L cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in foudation, filling and mass concrete including sub base of floors omplete all as specified and as directed by engineer-in-charge.

M&L for 75mm thick PCC 1:2:4 type B2 (using 40mm graded aggregate) laid in alternate panels as complete all as specified and as directed .

Preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted over a coat of chalk whiting complete all as specified and as directed by Engineer-in-Charge.

Prerparing old decorated surfaces plastered/unplastered by brooming down etc and applying one coat of white wash on ceiling complete all as specified.

Preparation of newly plastered surfaces of wall and applying two coats of cement based paint (Ist quality) over a coat of primer complete all as specified and directed by Engineer-in-charge.

Preparing new surface of steel of any desc over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed .

Prerparing new plastred surface of wall and applyin three coat of white wash on walls complete all as specified and directed by Engr In Charge.

Prerparing old decorated surfaces plastered/unplastered by brooming down etc and applying one coat of white wash on ceilings complete all as specified and as directed .

Complete removal of existing treatment of walls and applying two coat of cement base paint (Ist quality) in plain pattern on walls and over a coat of primer complete all as specified and as directed .

Preparing new surfaces of plastered or unplastered and applying three coat of white wash on ceiling complete all as specified and as directed .

M&L for Non-skid ceramic coloured tiles (square/rectengular) 7 to 8 mm thick, area of each tile exc 0.06 sqm but not exc 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over 15 mm thick cement screed bed CM (1:6) complete all as specified and directed.

M&L for Non-skid ceramic coloured tiles (square/rectengular) 7 to 8 mm thick, area of each tile exc 0.06 sqm but not exc 0.18 sqm but on vertical surface over 15 mm thick rendering in CM (1:4) on fair faces of brick work or concrete complete all as specified and as directed by Engineer-in-Charge.

M&L for Non-skid ceramic coloured tiles (square/rectengular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over 15 mm thick cement screed bed CM (1:6) complete all as specified and as directed by Engineer-in-Charge.

M&L for Non-skid ceramic coloured tiles (square/rectengular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm above but as in Skirting/dado and risers to ateps etc over 15 mm thick rendering in CM (1:4) on fair faces of brick work or concrete complete all as specified and as directed by Engineer-in-Charge.

Excavation in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning,filling in and ramming earth in layers n exc 25cm, watering and removing surplus soil to a distance n. exc 50 m and making good surface complete all as specified and as directed by Engineer-in-Charge

S & F Mild steel work for as in posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165, complete all as specified and as directed by engineer-in-charge.

M & L Cement concrete 1:3:6 type C 2 using 40mm graded stone aggregate as in foundations , filling and mass concrete including sub base of floors ,copings etc complete all as specified and as directed by engineer-in-charge.

M&L fly ash brick work in cement mortar (1:6) using old size sub class 'B' bricks in walling, straight or curved on plan exc 6m mean radius complete all as specified and as directed by Engineer-in-Charge.

Supply only Chain Link Fencing MS Galvanised any Size and type ( wt 2/Sqm approx) any type or size complete all as specified and as directed by Engineer-in-Charge.

Fixing only chain link fencing incl line wire, any mesh size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and as directed by Engineer-in-Charge.

S & F MS flat iron 40x6mm to secure chainlink fencing complete all as specified and as directed by Engineer-in-Charge.

M&L Mild steel round bars 10mm dia or over cut to length, blend to shape required, fixed independently to support chain link fencing complete all as specified and as directed by engineer-in-charge.

Preparing new or previously untreated steel & iron surface of any desc over 10cm width or girth and applying two coats of Aluminium paint over a coat of aluminium red oxide primer complete all as specified and as directed .

Preparation of newly plastered or inplastered surfaces of wall and applying two coats of cement paint over a coat white wash complete all as specified and directed by Engineer-in-charge.

M&L hardcore of broken stone or boulders of gauge n exc 63mm , deposited , spread and levelled in layers n exc 15cm thick watered and rammed to a true surface, complete all as specified and directed by Engineer-in-charge.

Surface excavation (not exceeding 30cm deep) and averaging 15 cm deep in soft and loose soil, complete all as specified and directed by Engineer-in-charge.

M & L Cement concrete 1:2:4 type B 2 using 40mm graded stone aggregate as in colums, pillars, boundry pillars and posts etc complete all as specified and as directed by engineer-in-charge.

M&L for 100mm thick PCC 1:2:4 type B2 (using 40mm graded aggregate) as in floor laid in alternate panels finished even and smooth with out using exra cement complete all as specified and as directed .

M&L 100 mm thick PCC(1:4:8) type D2 using 40mm graded stone agg as in sub base floors finished even and rough,complete all as specified and as directed by engineer-in-charge.

Taking down carefully existing unserviceable Copper/aluminum batten/surface conduit/concealed conduit point wiring (light, fan, bell/buzzer, socket or power) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, sockets, lamp holders, shades, fan regulators, light fittings, bells etc (including old MS sunken boxes) and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and as directed by the Engr-in-Charge.

Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 2.5 Sq mm single core in and including new non-metallic rigid PVC concealed conduit, not less than 20 mm dia, medium duty ISI marked, including conduit fittings such as tees, bends etc terminating in and including new sunken box covered with and including 3 mm thick bakelite laminated sheet top cover of approved make for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 2.5 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No 76.00 here-in-before but socket point on the same board with other switches complete as specifed as directed by Engineer - In - Charge .

All as per item No 76.00 here-in-before but socket point on independent board complete as specifed as directed by Engineer - In - Charge .

S&F Switch piano flush type, Single pole 5 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge .

S&F Socket outlet 2 in 1, 3 pin, 5A ISI marked, complete all as specified and as directed by Engineer-in-Charge .

S&F Lamp holder insulated body with back plate for conduit/casing capping fittings complete all as specified and as directed by Engineer-in-Charger.

S&F Ceiling rose PVC/poly carbonate insulated body three terminal ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F Sheet metal enclosure for distribution boards, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 2 ways single door , supplied and fixed , including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge.

S&F MCB single pole, 240 volts of rating 6-32 Amps, breaking capacity of 10 KA complete all as specified and as directed by Engineer-in-Charge .

Supply , fixing and connecting of LED street light made up of pressure dia cast aluminium housing with toughned glass and individual LEDs with secondery optics 25 watts including suitable size street light fitting bracket with suitable size clamps, nut bolts and washers including twin core flexible cable 2.5 sqmm as per site requirement complete all as specified and as directed by Engineer-in-Charge.

Supply & Fix LED Tube light ( Retro Fit) ingress protection IP20 18W in make Cat part No SSK-TL-18W-I-HD in make- Syska/Havells/Phillips with Connecting fixture for T8 Tube Light Cat part No SSK-T8-P-1201(1*18W/20W 4 Ft) in make - Syska/Havells/Phillips complete all as specified and as directed by Engineer-in-Charge.

Supply & laying or Fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheated 6 sqmm 2 core nominal cross section in service connection complete all as specified and as directed by Engineer-in-Charge.

Material and labour Earthing complete with galvanised iron earth plate electrode of size 60 x 60 x 0.60 cm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI wire 4 mm dia (upto the cross arms) by means of GI bolts/nuts/washers, protected by 15 mm bore GI light grade pipe. Earth plate shall be surrounded by alternate layer of charcoal or coke and common salt 15 cm thick all around bottom and top. 20 mm bore GI light grade pipe for watering and including funnel, wire mesh,RCC cover & frame, PCC (1:3:6) type C2 (using 20 mm graded crushed stone aggregate) as in earthing pit including necessary excavation & earth work in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance n.exc 50 m all as specified & shown in electrical plate No. 3 of SSR Part – I. (Note:- The unit rate includes earth lead upto 7.5 metre length from top of earth plate.)

Supply , fixing, testing and commissioning electric storage water heater (Geyser) vertical type with lined glass tank of capacity 25 Ltrs, 3 Star Rating on wall including grouting suitable size of nuts, bolts and washers and making good the surfaces of walls to match with the existing surface including PVC connection, transportation up to site complete all as specified and directed by Engineer in charge.

Supply , assembling and hanging ceiling fans 1200 mm sweep BEE, 5 star rating single phase 230 volts Copper Winding ( Double Ball -Bearing ) with 01Set of 03 Blades, down rod, canopies, hook with rubber reel safety pins complete including making connection from ceiling rose to connector with twin core twisted flexible and PVC insulated copper conductor cable complete all as specified and as directed by Engineer-in-charge. Make : CG/ Havells/Orient /Khaitan

S&F Fan regulator electronic type, 230 Volt, 150 Watt 1 modules with 5 step of control including making holes in laminated bakelite sheet cover and connection complete all as specified and as directed by Engineer-in-Charge.

S & F exhust fans AC single phase 230/240 Volt of size 450mm sweep with louver omplete all as specified and directed by Engineer in charge..

S & F exhust fans AC single phase 230/240 Volt of size 380mm sweep with louveromplete all as specified and directed by Engineer in charge.

S & F fabricated down rod made out of 15mm dia MS pipe Heavy Duty 1.0 mtr long duly painted including nut, bolt & washer etc suitable for 1200mm sweep of ceilling fanomplete all as specified and directed by Engineer in charge.

S & F fabricated down rod made out of 15mm dia MS pipe Heavy Duty 1.0 mtr long duly painted including nut, bolt & washer etc suitable for 1200mm sweep of ceilling fan omplete all as specified and directed by Engineer in charge.

S & F of flexible wire of size 23/0.0076 stranded copper conductor omplete all as specified and directed by Engineer in charge.

M/S ASHRAFI CONSTRUCTION CO

SHREE GURU NANAK CONSTRUCTION COMPANY

Beenu Co. Company

MAHAVIR CONSTRUCTION CO

GS BUILDERS AND ENGINEERS

M/S BUDHRAM BISHNOI

MITTAL ENTERPRISES