PROVN OF 70 CEILING FAN AND 14XEXHAUST FAN FOR OTM ACCN BLDGNO T-1,T-12 TO T-18, T-21,T-23,T-24,T-82,T-84,T-87, T-88, T-89, P-11 TO P-13 T15 TO P-17 AT RASPUNJA MIL STATION , PROVN OF FOL SHED (SIZE 12MX5MX3.10M) AT RASPUNJ MIL CAMP

Amount

Demolition of cement concrete (Un-reinforced) in ground floor and paving nexc 15cm thick above or below GL complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions, complete all as specified and as directed.

Dismantling AC Corrugated Sheets as in Roofing including Ridge or Similar Pattern Roof Coverings, complete all as specified and as directed.

Dismantling of Wall and Ceiling Board (Fibre, Pulp, Insulation etc.) or Insulation Board/Slab /Blankets, any thickness including Cover Fillets, complete all as specified and as directed.

Taking down existing Water Proofing Treatment with and including roof tiles and padding upto original roof and removing debris from the Site, complete all as specified and as directed.

Dismantling Wrought Iron or Mild Steel Work, viz. MS Flat Iron (Wind Tie) and Similar Work including MS Bolts, Nuts, etc., complete all as specified and as directed.

Dismantling Timber Scantlings, 40 Sqcm and over in Section, in any Position, in Unframed Work, complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlings, etc., under 40 Sqcm in Section, in any Position, as in Unframed Work, complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutter from frames) of any sizes n exc 1.5 Sqm each complete all as specified and directed.

Taking down Chowkat or Frame with shutters (without taking off Shutter from the Frame) exc. 1.50 Sqm but not exc. 4.00 Sqm Each, complete all as specified and as directed.

Dismantling floors hearth or wall tilling including cement mortor bedding (but not backing) removing serviceble tiles to store and rubbish off the premises complete all as specified and directed.

Taking down cement plaster of any description on brick work or stone msonary wall including racking ot joints hacking for key scrubbing down with water etc. complete all as specified and directed.

Taking up or down Steel Water Tubing 15mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use, or removing to store, complete all as specified and as directed.

Taking up or down Steel Water Tubing 20mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use or removing to store, complete all as specified and as directed.

Taking down unserviceable PVC (SWR) Pipes & Fittings of any size or pattern and in any Position (Measured overall as fixed along the Centre Line over the Fittings and Accessories), complete all as specified and as directed.

Surface dressing not exc. 150mm deep and getting out in Soft/Loose Soil, complete all as specified and as directed.

Excavating in trenches, n exc 1.50 m wide and n exc 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft and loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth round, in layers not exceeding 25 cm in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point as in soft/loose soil complete all as specified and directed.

M&L Moorum/red bajri filling in floors or pavings , laid in lyers 30 cm in thick spread , levelled and rammed including watering complete all as specified and directed by Engr-in-charge.

M&L Hardcore (broken stone or boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for Cement concrete type 1:3:6 type C-2 (Using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L Plain Cement Concrete type C-1, (1:3:6) (40mm graded crushed stone aggregate) as in Coping bed plate,hold fast etc,block benching,channeling slightly rounded or chamfered angle and throating including form work and finishing all exposed faces of cement concrete complete all as specified and as directed.

M&L Reinforced Cement Concrete (Design Mix) M-25 in Roof Beams, Cantilevers, Bres-summers, Lintels over 1.50 Metre Span, complete all as specified and as directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Reinforced Cement Concrete type B1(1:2:4) using 20 mm graded crushed stone aggregate) as in slab ,shelves , chajja suppoted on walls beam and column in floor roof including balconies canopics , deck slabs complete all as specified and directed. NOTE : Reinforcement shall be measured and paid separately under relevant Item.

Cutting chases, pinning in making good to facing where required and pointing in CM 1:3 to end or edges of landing steps, cills, sunshades, shelves, lintels etc. and cutting chase for concealed water pipe etc. and making good cutting not exc 10Cm girth complete all as specified and directed.

M&L Pulverizes fly ash bricks using class 'A ' old size bricks straigth or curved on plan exc 6m mean radius built in CM (1:6) cmplete all as specified and directed.

M&L Brick Work pulverizes fly ash bricks ,Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Beam Haunchings, Girders, Bres-Summers, Lintels, Cantilevers, Shelves including supports, overhangs, etc. also splays between floors and beams, etc., flat, rough finished surfaces of concrete, complete all as specified and as directed.

M&L Formwork to Soffits of suspended slab such as Roof slab, Floor slab, landings and similar works horizontal or sloping etc., not exceding 200mm thick ,flat rough finished surfaces of concrete, complete all as specified and as directed.

S&F for 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to cowkhats complete all as specified and directed.

S&F 2nd class hardwood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I 2009 complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening with and including 3 Nos. stainless steel butt hinges 75mm long complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter With Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed.

M&L TMT Bars 8 mm dia , cut to length, bent to shape required including crank-ing, bending and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm, as in stirrups spacers and binders complete all as specified and as directed.

S&F Welded steel wire fabric weight not more than 4Kg/Sqm fitted by mild steel nails complete all as specified and directed.

S&F Rolled mild steel sections as in main and cross beams,hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors,fixed with angle cleats or other connecting plates of Fe-410-W(Gde-E-250) quality-B complete all as specified and as directed.

M&L Steel Work in Tubular post and Trusses /hollow section including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1979grade YSt.-240 complete all as specified and as directed.

S&F Plates (Plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming toFe-410-W (Gde-E- 250 quality -B) complete all as speci-fied and as directed.

M&L Mild Steel Screw Bolts (machine made) 11mm to 15mm diameter of neck and length of bolt exc 22.5 Cm and not exc. 30 Cm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated/semi corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, fixed with self tapping screw complete all as specified and directed.

M&L Cement Concrete, Type B-O, 1:2:4 (12.50 mm graded stone aggregate) as in roof padding mixed with water proofing compound and the concrete surfaces is to be finished even and fair without using extra cement complete all as specified and as directed. (Note : WPC shall be measured and paid separately under relevant item)

M&L for 10mm thick screed bed or bedding over roof surfaces when concrete is still green with and including WPC in cement mortar 1:3 complete all as specified and directed.

M&L Water Proofing Treatment on existing cleaned RCC Roof with the following Specifications and Manufacturer's instructions, complete all as specified and as directed :- (a) Preparing and cleaning of fully dry surface as per IS:3067-1966. (b) Applying Bitumen Primer conforming to IS-3384-1986 over the Cleaned Plastered Surface @ 0.40 Litre per Sqm. (c) Applying a layer of APP based Polymeric Membrance; 3.0mm thick (minimum) weighing 3.60 Kilogram per Square Metre (reinforced) with Polyster Non Woven Fabric weighing not less than 160 Grams per Square Metre by Torch application and two coats of Bitumen based UV reflective paint with aluminium finish . The overlaps shall be minimum 100mm on the Transverse direction and 75mm on Longitudinal direction.

M&L False ceiling with 'E' board "Classic" , reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium powder coated snap grid to support the boards/files with aluminium anodised main 'T' section 35mm x 23mm x 1.50mm cross tee 35mm x 23mm x 1.50mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides duly suspended with 4mm dia GI hanger fixed with GI hooks 4mm dia and fastner as required at the site and applying two coats of oil bound distemper over a coat of alkali resistant primer on exposed surfaces complete all as specified and as directed.

S&F 40mm bore MS tubing medium grade and fixed at wall for ceiling complete all as specified and directed.

M&L Pressed steel frames for doors with one or more rebates size of frame 125 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note :- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate

M&L Pressed steel frames for doors with one or more rebates size of frame 105 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note :- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate.

M&L 1.50mm thick power coated aluminium , three track sliding window with three nos shutters made of aluminium section as per drawing no CWE/KOL/TD-33 of section no 1F-1F including necessary jointing cleats, glazing clips, rubber neoprene packing, roller, locking arrangement, handles 2 Nos , anodised aluminium snap beading screws etc.Complete all as specified and as directed. Note Nos :- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall be deem to included quoted rate. Only measure opening size of window. (ii) Only Glass for window & wire mesh shall be measure and paid separately under relevant items of BOQ .

S&F Powder coated aluminium ventilators with louvers and glazing including frame of section over all size of window 600X450mm complete with following specification . (a) Alu frames of size 45x45x1.2mm (b) Rail & Stile 45x45x1.2mm thick (c) 4.80mm thick frosted sheet glass Note :- All ventilators/louvers member including fitting & fixture shall be deem to included quoted rate. Only measure opening size of ventilators/louvers

M&L Framed Work such as Grills, Gratings, etc. with ends of Bars shouldered and/or riveted, or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walk Ways; Railings; Framework of Water Tanks and Similar Work, conforming to Fe-290, Gde-E-165, complete all as speci-fied and as directed.

S&F 100mm Butt hinges, extruded brass, with brass hinge pin, bright polished, complete all as specified and directed.

S&F Aluminium anodised, barrel tower bolts of extruded section 200mm long complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy of 300mm long complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised 150mm long complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, 150mm long complete all as specified and directed.

M&L for 18/19 mm thick Medium density fibre board, exterior grade, fixed to timber framework with screws complete all as specified and directed.

S&F 30mm width of flaps Continous (Piano) hinges, brass, bright finish or electrogalvanised complete all as specified and directed.

S&F for 40mm dia cupboard knobs fixed with nut screws and washer of wooden finish brass polished complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L Drapery rod made of electric resistance welded MS pipe of 20mm dia having a coating of corrugated virgin PVC extrusion and cover with ABS plastic complete all as specified and directed.

S&F End Stopper, Decorative type for drapery rod and including closed type stainless steel brackets fixed on wall complete all as specified and directed.

S&F 300mm, ordinary mild steel rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directed Note:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate

M&L Cement Concrete type D2 (1:4:8) using 40mm graded aggregate 75mm thick in Sub-bases, finishing concrete surfaces fair and even, complete all as specified and as directed.

M&L 150mm thick PCC (1:2:4) type B-2 (Using 40mm graded stone aggregate) as in sub base for path/hard standing cement complete all as specified.

M&L Cement Concrete type B0 (1:2:4) (12.5mm graded aggregate) 25mm thick, in Flooring, finishing concrete surfaces fair and even, complete all as specified and as directed.

M&L 20mm thick Wearproof topping as specified (incorporating an approved metallic floor hardner), laid on concrete floors and pavings, and finished even and smooth (except metallic hardner) complete all as specified and as directed.

"Supply only" metallic hardner (ISI marked) complete all as specified and directed.

M&L joint free non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L joint free non skid ceramic coloured tiles (double charge) 8-10mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

M&L joint free non skid ceramic coloured tiles (double charge) 8-10mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Granite (of any type) Work (Table rubbed and polished) 18 to 20 mm thick, in Steps, Cooking Platforms and like, Set in Screed bed of 20mm thick in Cement Mortar 1:6 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Granite including Cutting and Polishing including half round edges, complete all as specified and as directed.

M&L Glazed Ceramic Coloured Tile 450x350x7mm thick on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar on fair faces of brick work or concrete surface of wall in cement morter (1:4) using water proofing compound and finishing the surface even and smooth without using extra cement complete all as specified and as directed. . (NOTE:-WPC shall be measured and paid separately)

M&L rendering 15mm thick in CM (1:6) on other than fair faces of brick work or concrete surfaces even & smoth without using extra cement complete all as specified and directed.

M&L rendering 5mm thick in CM (1:3) as in ceiling surfaces even & smooth without using extra cement complete all as specified and directed.

"Supply only" liquid water proofing compound (ISI marked) complete all as specified and directed. Make:- STP NO 1/ PEDILITE(DR FIXIT)/ FOSROC/ CICO/ SIKA

S&F 4.80mm thick tinted sheet glass , pin head type and glazing in squares exc 0.5 sq. M in each pane complete all as specified and as directed.

M&L Preparing new Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Complete removal of existing Treatment of old decorated Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L preparing new Surfaces of Ceiling and applying Three Coats of White Wash, complete all as specified and as directed.

M&L complete removal of existing Treatment of old decorated Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 3mm thick BIRLA/JK water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L Preparing new Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 3mm thick BIRLA/JK water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L Complete removal of old decorated surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L Preparing newly plastered surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L Preparing new Wood and Wood Based Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Pink Primer, complete all as specified and as directed.

M&L for preparation of old surfaces of steel or steel based materials of any descriptionand applying one coat of synthetic enamel paint (First quality) over 10 Cm width or girth complete all as specified.

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

S&F 20mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F 25mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F Chromium plated Fancy type Bib taps for 15 mm bore of pipe complete all as specified and directed. Make : Essco (TQT-CHR-511) or equivalent make specified in the particular specification

S&F Chromium plated long body Bib taps for 15 mm bore of pipe with wall flange complete all as specified and directed. Make : Essco (TQT-CHR-511) or equivalent make specified in the particular specification

S&F Brass chromium plated two in one tap with Wall Flange screwed for 15 mm bore pipe as in repair complete all as specified and directed Make : Essco (TQT-CHR-512AN) or equivalent make specified in the particular specification

S&F ABS body chrome plated shower rose 125mm size including fixing to steel pipe or union as in repair complete all as specified and directed Make : Essco (EOS-542A) or equivalent make specified in the particular specification

S&F Shower arm 240mm long round shape with flange including fixing to steel pipe or union as in repair complete all as specified and directed Make : Essco (ALE-536A) or equivalent make specified in the particular specification

S&F 15mm bore brass chromium plated Angular Valve with Wall Flange as in repair complete all as specified and directed. Make : Essco (TQT-CHR-526N) or equivalent make specified in the particular specification

S&F 20 mm dia Chromuium Plated tublar towel rail 600 mm long fixed to walls with chromium plated brass screw including necessary fixing arrangement as in repair complete all as specified and directed. Make : Essco (AEC-CHR-1111N) or equivalent make specified in the particular specification

S&F PVC bathroom cabinet (white) of size 430 x 330 x 100 mm (approx) with one single shutter and built in mirror in front of shutter, fixed on walls with wooden plugs and and chromium plated brass screw and cup washer complete all as specified & directed. Make -Prayag or equivalent make as specified in Particular Specification here in after.

S&F Kitchen sink of overall size 495 mm x 420 mm and bowl size 410 mm x 330 mm x 160 mm depth, made out of 1 mm thick stainless steel sheet, with plugs, washers, 32 mm dia PVC waste pipe, bedding in cement mortar including fixing cast iron cantilever brackets (of suitable size), connecting union and making good with cement mortar 1:3 to match with the existing surfaces etc complete all as specified and as directed.

S&F stainless steel utencil plate rack (size 24'' x 30'' x 10'') using 0.8mm thick sheet with all fittings accessories complete as directed. Make:- Essco (CAT No. P-340) or equivalent make specified in the particular specification

S&F Chromium plated Health faucet with 8mm Dia, 1.2 Meter long flexible tube and wall hook with N.R.V (Back Flow Preventer) as in repair complete all and specified and directed Make:- Essco (CAT No. ALE-ESS-583) or equivalent make specified in the particular specification

S&F Vitreous China Colour Wash down Water Closet Pan (Pedestal Pattern) with "p" or "s" trap front or back inlet including fixing Bolts with and excluding 10 litre capacity low level Flushing Cistern matching with water closet colour with inlet ball valve float handle and providing 32mm dia PVC flush pipe including plastic water closet seat with flat botton cover (coloured) fixed with mild steel chromium plated or aluminium hinging device including taking down old one complete all as specified and as directed. Make - Parryware Model No-C0297 Hindware(20011-SW), Essco (ECS-WHT-551PSPP)or equivalent model as specified in Particular Specification here in after.or equivalent make as specified in the particular specfication.

S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting and 15mm dia PVC connector pipe, a pair of Cast Iron Brackets duly painted Stand including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including taking down old one complete all as specified and as directed. Make - Parryware Model No-C0406(SP)/C0434(CTH) ,Hindware(10100-sw) Essco (ECS-WHT-801)or equivalent make as specified in the particular specfication.

S&F White PVC Flushing Cistern 10 Litre capacity, Low Level Valve Less, Syphonic Action type with Inlet, Ball Valve, Float and Handle including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 and fixed to WC complete all as specified and as directed. Make : Parryware Model No- E-8090, Cera cat part No CONGO B1010109 ,Hindware(510648-SW), Essco (ECS-WHT-201C)or equivalent model as specified in Particular Specification here in after.

S&F PVC Conncetions 15mm size with PTMT Nuts of length 450mm complete all as specified and as directed.

S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 500Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including provision of 25mm x 100mm GI nippples with check nuts for inlet, outlet wash and overflow pipe including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed.

S&F PVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), Type "B" single socketed, in any length with Rubber Ring Joints fixed to Walls, complete all as specified and as directed.

S&F PVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), Type "B" double socketed, in any length with Rubber Ring Joints fixed to Walls, complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia), any type etc. and Jointing with Solvent Cement as in repair complete all as specified and as directed.

S&F UPVC (SWR) Junction 110mm bore (dia), Single (Single T) equal or unequal and Jointing with Solvent Cement as in repair complete all as specified and as directed.

S&F UPVC (SWR) Nahani/Floor Trap 75mm bore (dia) Outlet, Plain with Grating and Jointing with Solvent Cement as in repair complete all as specified and as directed.

S&F 3-in-1 wall mixer for Hot & Cold water supply with provision for Overhead Shower with 115mm long Bend Pipe on Upper Side, Connecting Legs & Wall Flanges screwed down for 15mm bore iron pipe incl necessary fittings & fixtures etc as in repair complete all as specified and directed. Make : Essco (TQT-CHR-517B) or equivalent make specified in the particular specification

S&F Central hole for Hot and Cold water supply basin mixer, brass chromium plated screwed down for iron pipes,including necessary fittings etc as in repair , complete all as specified and as directed. Make : Essco (TQT-CHR-516A) or equivalent make specified in the particular specification

Taking down point wiring (light, fan, socket and power complete including fixtures and fittings such as switches ceiling roses, pendents , regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody for refixing or for taking credit (credit for above items should be made as per conditions separately) and making good distrubed surfaces of walls, floors, etc.complete all as directed by Engineer-in-Charge.

M&L Point wiring with PVC insulated and unsheathed FRLSH cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS - 694 1990 drawn through and including PVC casing caping of suitable size with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3 mm thick plastic masonite laminated sheet top cover fixed with cadmium screw for mounting switches, sockets, regulator etc including 1.5 sq mm FRLSH stranded PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly for one light or fan point controlled by one switch single pole one way for light/ ceiling fan/ exhaust fan /call bell point/ Switch socket outlet 5 amps complete all as specified and as directed. Note: Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board..

All as per item No. 121.00 here-in-before but one 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed by Engineer-in-charge.

All as per item No. 121.00 here-in-before but one 3 pin 5 amps switch socket commbination on the independent board with other switch complete all as specified and directed by Engineer-in-charge.

M&L fo Point wiring surface type with 2.5 sqmm (Nominal Area) PVC insulated stranded single core unsheathed FRLSH copper conductor cable 1100 Volts grade drawn through with and including PVC casing caping with all fittings and accessories of casing caping (like Tee, Bend etc) complete fixed to walls / ceiling etc with and including 2.5 Sqmm (nominal area) PVC insulated unsheathed, stranded, single core FRLSH copper cable as earth continuity wire connecting to common earth point (including supply & fixing of 1.6 mm thick pressed mild steel terminal boxes of suitable size with 3 mm thick PVC /plastic laminated sheet, top cover suitable sizes of brass screws and washers etc. for mounting sockets for 5 pin, 16 Amp Switch socket combination on independent board complete all as specified and directed.

M&L for Point wiring with PVC insulated and unsheathed FRLSH cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS - 694 1990 drawn through and including PVC concealed conduit 20mm dia medium duty with all accessories including fabricated 1.6 mm thick MS terminal boxes fixed flush with wall surface with 3 mm thick plastic masonite laminated sheet top cover fixed with cadmium screw for mounting switches, sockets, regulator etc including 1.5 sq mm FRLSH stranded PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for one light or fan point controlled by one switch single pole one way for light/ ceiling fan/ exhaust fan/call bell point/ Switch socket outlet 5 amps complete all as specified and as directed. Note: (i) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board. (ii) Cutting Chases pinning shall be measured and paid separately under relevant item of Sch A

All as per item No 125.00 here-in-before but one 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed by Engineer-in-charge.

All as per item No. 125.00 here-in-before but one 3 pin 5 amps switch socket outlet on the independent board with other switch complete all as specified and directed by Engineer-in-charge.

M&L Point wiring with 2.5 sqmm (Nominal Area) PVC insulated stranded single core unsheathed FRLSH copper conductor cable 1100 Volts grade drawn through with and including PVC concealed conduit 20mm dia medium duty with all fittings and accessories of casing caping (like Tee, Bend etc) complete fixed to walls / ceiling etc with and including 2.5 Sqmm (nominal area) PVC insulated unsheathed, stranded, single core FRLSH copper cable as earth continuity wire connecting to common earth point (including supply & fixing of 1.6 mm thick pressed mild steel terminal boxes of suitable size with 3 mm thick PVC /plastic laminated sheet, top cover suitable sizes of brass screws and washers etc. for mounting sockets for 5 pin, 16 Amp socket outlet on independent board complete all as specified and directed. Note: (i) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board. (ii) Cutting Chases pinning shall be measured and paid separately under relevant item of sch A

S&F Switch socket combination multipurpose 2 in 1, 3 pin 6 Amps 230/240 volt flush type complete all as specified and as directed.

S&F Socket outlet 3/5 pin, 6 Amps, 240 volt flush type complete all as specified and as directed.

S&F Switch socket combination multipurpose 2 in 1, 3 pin 5 & 15 Amps 230/240 volt flush type as in repair complete all as specified and as directed.

S&F Bell/buzzer push 5/6 amps, flush type, white/ivory finish complete all as specified and as directed.

S&F Call bell ding dong AC 230 volts, single pole complete all as specified and as directed.

S&F Switch piano, flush type, SP, one way, 5/6 Amps 230/240 Volts, white/ivory finish complete all as specified and directed.

S&F Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

S&F Lamp holder suitable for batten fittings complete all as specified and directed by the Engr-in-Charge.

S&F Ceiling fans complete with blades, down rods, electronic regulator and acessories 230 V 1200 mm sweep Min air delivery 210 CFM with service Value 6.00 BEE 5 Star rated with brushless direct current motor (BLDC) complete all as directed and specifed.

S&F Exhaust fan AC single phase 240 V of size 300 mm sweep with louver specially designed by toilet/bathroom in domestic ventilattion metal body and blade, powder coated metalic finishes heavy duty motor, protective bird guard complete all as directed and specifed.

Cutting the existing required on brick wall in square/round type suitable for fixing exhaust fan including cement work grouting 4 nos long bolts nuts washers and making good to distubed surface with cement mortar 1:3 and distemper /Colour wash etc to match with existing surfaces including facing, finishing complete all as directed by Engr-in-charge.

Supply and fix LED tube light fittings of with LED tube capacity 20W suspended type/ wall mounted type and necessary connection with PVC cable of 0.50 sq mm three core sheatered not more than 0.5 meter in lenght complete all as specified and as directed. Make:- Bajaj cat Part No.BCLAB 20 WH LED P or Make:- Crompton cat Part No.LDL-20W or Make:- Havells cat part No. LUMILINEPLUSBS10WLED865SPCSS.or equivalent

Supply and fix LED tube light fittings of with LED tube capacity 10W suspended type/ wall mounted type and necessary connection with PVC cable of 0.50 sq mm three core sheatered not more than 0.5 meter in lenght complete all as specified and as directed. Make:- Bajaj cat Part No.BCLSB 10 WH or Make:- Crompton cat Part No.LDL-10W or Make:- Havells cat part No. LUMILINEPLUSBS10WLED865SPCSS.or equivalent

Supply and fix LED light fittings 18 watts flame poof, CIMFR certified recommended for gas/ vapour group of IIA & IIB , zone 1&2 and IP 65 protection with die cast aluminium housing with heat resistant toughned glass with LED tubelight fixtures driver holders, connector etc complete with all accessories prewired and necessary connection with PVC cable of 0.50 sq mm three core complete all as specified and as directed. Make Bajaj Cat No BIFPBT218 Make CG Cat No EXNILTS-16/20 or equivalent

Supply & fix LED Building security light 36 watt in aluminium PDC housing, toughened glass cover with IP66 dia GI pipe of suitable size making connection with PVC cable of 0.50 sq mm three core sheatered not more than 0.5 meter in lenght complete all as specified and as directed. Make:- Crompton cat part No.LST-35-CDL-M or Make:- Surya cat Part No. SLE UL 35W IP66 (LXN) or Make:- Bajaj cat part No ENXTP36LWHPOPC SD or Make CG Cat No LSTS-36-CDL-M or equivalent.

Taking down unserviceable rusted / damaged MCB DBs of any type and way along with any type MCB and keeping serviceable MCB in safe custody in re-use in the work and making good to the distubed surfaces of walls etc. complete all as specified and as directed.

S&F Sheet metal enclosure doubleDoor for DB's where MCBs to be used 8 way single pole and neutral with 200 amps rated bus bar complete all as specified and as directed.

S&F Sheet metal enclosure double Door for DB's where MCBs to be used 4 way single pole and neutral with 200 amps rated bus bar complete all as specified and as directed.

S&F MCB 40 Amps, SPN 240 Volts , 'C' curve braking capacity 10 kA complete all as specified and as directed.

S&F MCB 6 to 32 Amps, SP, 240 Volts , 'C' curve braking capacity 10 kA complete all as specified and as directed.

S&F MCB 40 amps, TPN, 415 Volts , 'C' curve braking capacity 10 kA complete all as specified and as directed.

M&L Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.00 mm thick burried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI strip 32x6 as earthing lead by means of bolts, nuts, check nuts and washers of GI or steel, GI strip proected by 40 mm bore light grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20 mm bore light grade galvanised iron, wire mesh, charcoal or coke common salt laid in alternative layer of 15 cm (complete thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1, 50 mm thick pre-cast RCC (1:2:4) type B-1 normal mix cover slab reinforced with 8 mm dia TMT bar 10 cm c/c bothways and single handle of 10 mm dia round bar including necessary excavation, earth work etc. in soft / loose soil and disposal pf soil to a distance n. exc. 50 m and necessary testing on completion all as shown in electrical plate No. 3 MES Schedule Part-I complete all as specified and as directed.

Taking down old burnt/unserviceable submain wiring with aluminum/copper conductor PVC insulated cable of any size drawn through PVC casing caping/ PVC Conduit pipe including GI wire accessories etc. and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L Sub main wiring with 2 runs of single core FRLSH type PVC insulated unsheathed stranded copper conductor of size 4.0 Sqmm and one run of PVC insulated unsheathed multistrand copper conductor FRLSH type of size 4.0 Sqmm as earth lead drawn into rigid non metalic PVC Casing caping of size 20 mm dia including all fittings complete all as specified and as directed. Note:- Two runs of 4 Sqmm conductor as main wire and one run of 4 Sqmm conductor as earth wire with one run of PVC conduit shall be measured as one unit.

Supply and laying dry coarse sand as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23 Cm (15 Cm under the cable & 8 Cm over the cable) and gently punned down to 18 Cm thickness complete all as specified and as directed. Note:- Thickness after punning down shall be measured for payment.

Supply and laying in trenches Bricks, sub class 'B' over burnt (kiln burnt) old size bricks, laid flat dry with width of the bricks laid to the axis of the cable for protection of cable complete all as specified and as directed.

Supply & laying or fixed with bldg incl clamps for XLPE insulated PVC sheathed armoured LT 1100 volt grade aluminimum conductor cable of size 16 Sqmm 2.0 core complete all as specified and directed.

S B ENTERPRISE

NICE INFOTECH

CIVCON

KWALITY CONSTRUCTION