REPAIR/MAINT OF PUMP SET, CHLORONOME PLANTS, STARTERS AND CONNECTED ITEMS IN WATER SUPPLY UNDER GE (AF) TECH AREA, AT AF STN AGRA

Amount

Dismantling/opening of unserviceable AC electric motor of 3 phases 415 Volts of any make of capacity 60 to 75HP of centrifugal/ boosting type pump from site and transporting the same to workshop & back after rewinding of motor with and including super enamelled copper winding wire of superior quality of existing size/ gauge & No of turns and insulation of the same with & including insulating material such as leatherised fibre glass insulation as per manufacturers instructions including cutting and taking out existing burnt/ short circuited winding wires complete and re-assembling of the same after repair, commissioning and testing on completion complete all as directed.

Taking out centrifugal pump set connected with 60 to 75 HP motor from existing foundation after disconnecting all electrical connections and dismantling/ opening of unserviceable centrifugal pump set for making it serviceable by repair/ replacement of the following items and re-assembling/ re-fitting & re-installation of the same in existing position after complete repair including making all electrical connections, commissioning and testing on completion complete all as directed:-

S&F in repairs ball bearing suitable for 60/75 HP centrifugal pump set complete all as directed.

S&F in repairs SS pump shaft 50mm dia with neckring as per existing suitable for 60/75 HP centrifugal pump set complete all as directed.

S&F in repairs rubber coupling with all fixing accessories as per existing suitable for 60/75 HP centrifugal pump set complete all as directed.

S&F in repairs MS coupling with all fixing accessories as per existing suitable for 60/75 HP centrifugal pump set complete all as directed.

S&F in repairs gland plate with nuts, bolts and washers as per existing suitable for 60/75 HP centrifugal pump set complete all as directed.

S&F in repairs cast iron impeller as per existing suitable for 60/75 HP centrifugal pump set complete all as directed.

S&F in repairs stainless steel sleeves as per existing suitable for 60/75 HP centrifugal pump set complete all as directed.

Dismantling/opening of unserviceable AC electric motor of 3 phases 415 Volts of any make of capacity 40HP of centrifugal/ boosting type pump from site and transporting the same to workshop & back after rewinding of motor with and including super enamelled copper winding wire of superior quality of existing size/ gauge & No of turns and insulation of the same with & including insulating material such as leatherised fibre glass insulation as per manufacturers instructions including cutting and taking out existing burnt/ short circuited winding wires complete and re-assembling of the same after repair, commissioning and testing on completion complete all as directed.

Taking out centrifugal pump set connected with 40 HP motor from existing foundation after disconnecting all electrical connections and dismantling/ opening of unserviceable centrifugal pump set for making it serviceable by repair/ replacement of the following items and re-assembling/ re-fitting & re-installation of the same in existing position after complete repair including making all electrical connections, commissioning and testing on completion complete all as directed:-

S&F in repairs ball bearing suitable for 40 HP centrifugal pump set complete all as directed.

S&F in repairs pump shaft 50mm dia with neckring as per existing suitable for 40 HP centrifugal pump set complete all as directed.

S&F in repairs gland plate with nuts, bolts and washers as per existing suitable for 40 HP centrifugal pump set complete all as directed.

S&F in repairs GM bush 50mm dia as per existing suitable for 40 HP centrifugal pump set complete all as directed.

S&F in repairs gun metal impeller as per existing suitable for 40 HP centrifugal pump set complete all as directed.

S&F in repairs rubber coupling with all fixing accessories as per existing suitable for 40 HP centrifugal pump set complete all as directed.

S&F in repairs MS coupling with all fixing accessories as per existing suitable for 40 HP centrifugal pump set complete all as directed.

Taking out submersible pump set including motor of capacity 1.5-2.0HP with column pipe from bore well after disconnecting all electrical connections and lowering the same after necessary repair/ replacement of wornout/ damaged parts of pumps/ motors/ column pipe & pipe joints including making all electrical connections and testing on completion complete all specified and directed. Note:- Repair/ replacement of wornout/ damaged parts of pumps/ motors/ column pipe shall be measured and paid separaterly under respective items of Sch 'A'.

Taking out submersible pump set including motor of capacity 5.0-7.5HP with column pipe from bore well after disconnecting all electrical connections and lowering the same after necessary repair/ replacement of wornout/ damaged parts of pumps/ motors/ column pipe & pipe joints including making all electrical connections and testing on completion complete all specified and directed. Note:- Repair/ replacement of wornout/ damaged parts of pumps/ motors/ column pipe shall be measured and paid eparaterly under respective items of Sch 'A'.

Taking out submersible pump set including motor of capacity 10.0-12.5HP with column pipe from bore well after disconnecting all electrical connections and lowering the same after necessary repair/ replacement of wornout/ damaged parts of pumps/ motors/ column pipe & pipe joints including making all electrical connections and testing on completion complete all specified and directed. Note:- Repair/ replacement of wornout/ damaged parts of pumps/ motors/ column pipe shall be measured and paid separaterly under respective items of Sch 'A'.

Taking out submersible pump set including motor of capacity 15.0HP with column pipe from bore well after disconnecting all electrical connections and lowering the same after necessary repair/ replacement of wornout/ damaged parts of pumps/ motors/ column pipe & pipe joints including making all electrical connections and testing on completion complete all specified and directed. Note:- Repair/ replacement of wornout/ damaged parts of pumps/ motors/ column pipe shall be measured and paid separaterly under respective items of Sch 'A'.

Taking out submersible pump set including motor of capacity 30.0HP with column pipe from bore well after disconnecting all electrical connections and lowering the same after necessary repair/ replacement of wornout/ damaged parts of pumps/ motors/ column pipe & pipe joints including making all electrical connections and testing on completion complete all specified and directed. Note:- Repair/ replacement of wornout/ damaged parts of pumps/ motors/ column pipe shall be measured and paid separaterly under respective items of Sch 'A'.

Supply & lowering in bore well in repairs 32mm bore high density polyethlene (HDPE) column pipe of pressure rating 6Kg/cm2 with & including all necessaru fixing/ jointing accessories complete all as specified and directed.

S&F in repairs 80mm bore MS column pipe heavy grade with heavy duty MS flange welded at both end, 3.0M long with and including making flange joint with 3mm thick rubber sheet including painting with anticorosive paint & necessary nuts & bolts etc of suitable size complete all as specified and directed.

S&F in repairs 100mm bore MS column pipe heavy grade with heavy duty MS flange welded at both end, 3.0M long with and including making flange joint with 3mm thick rubber sheet including painting with anticorosive paint & necessary nuts & bolts etc of suitable size complete all as specified and directed.

Dismantling/opening of unserviceable submersible pump set of capacity 1.5-2.0HP of any make for complete servicing with materials including cleaning, grinding, polishing & reassembling the same and testing on completion complete with replacement of the following items/parts:-

M&L for rewinding of motor with PVC insulated water proof copper winding wire best quality of existing gauge & No of turns and sealing the winding by using sealing compound including cutting and taking out existing burnt winding complete.

Replacement of all defective parts of pump set of existing size & make complete. Note:- All defective parts shall be measured and paid separately under respective item of Sch ‘A’ as supply only.

Dismantling/opening of unserviceable submersible pump set of capacity 5.0-7.5HP of any make for complete servicing with materials including cleaning, grinding, polishing & reassembling the same and testing on completion complete with replacement of the following items/parts:-

M&L for rewinding of motor with PVC insulated water proof copper winding wire best quality of existing gauge & No of turns and sealing the winding by using sealing compound including cutting and taking out existing burnt winding complete.

Replacement of all defective parts of pump set of existing size & make complete. Note:- All defective parts shall be measured and paid separately under respective item of Sch ‘A’ as supply only.

Dismantling/opening of unserviceable submersible pump set of capacity 10.0-12.5HP of any make for complete servicing with materials including cleaning, grinding, polishing & reassembling the same and testing on completion complete with replacement of the following items/parts:-

M&L for rewinding of motor with PVC insulated water proof copper winding wire best quality of existing gauge & No of turns and sealing the winding by using sealing compound including cutting and taking out existing burnt winding complete.

Replacement of all defective parts of pump set of existing size & make complete. Note:- All defective parts shall be measured and paid separately under respective item of Sch ‘A’ as supply only.

Dismantling/opening of unserviceable submersible pump set of capacity 15HP of any make for complete servicing with materials including cleaning, grinding, polishing & reassembling the same and testing on completion complete with replacement of the following items/parts:-

M&L for rewinding of motor with PVC insulated water proof copper winding wire best quality of existing gauge & No of turns and sealing the winding by using sealing compound including cutting and taking out existing burnt winding complete.

Replacement of all defective parts of pump set of existing size & make complete. Note:- All defective parts shall be measured and paid separately under respective item of Sch ‘A’ as supply only.

Dismantling/opening of unserviceable submersible pump set of capacity 30HP of any make for complete servicing with materials including cleaning, grinding, polishing & reassembling the same and testing on completion complete with replacement of the following items/parts:-

M&L for rewinding of motor with PVC insulated water proof copper winding wire best quality of existing gauge & No of turns and sealing the winding by using sealing compound including cutting and taking out existing burnt winding complete.

Replacement of all defective parts of pump set of existing size & make complete. Note:- All defective parts shall be measured and paid separately under respective item of Sch ‘A’ as supply only.

Flushing/cleaning of existing tube wells in position at various locations by air compressor unit of capacity not less than 300 PSI with minimum pressure of 7 kg/cm2 for sand free water including all necessary materials, labour, tool & plants etc as required and testing of yield complete all as specidied and directed.

Taking out submersible pump sets of any capacity from existing bore wells with column pipe after disconnecting all electrical connections and refitting & lowering the same after development including making all electrical connections and testing on completion complete all as directed.

Supply only the following parts/ items of submersible pumps and bowl assembly for replacement of parts/ items under item Nos. 13 to 17 above complete all as directed:-

GM impeller as per existing suitable for 10.0-12.5HP submersible pump sets complete all as directed.

Intermediate bowl as per existing suitable for 10.0-12.5HP submersible pump sets complete all as directed.

Rotor assmbly complete with rotor shaft suitable for 10.0 - 12.5 HP submersible pump set complete all as directed.

Bowl bush (gun metal) as per existing suitable for 10.0-12.5HP submersible pump sets complete all as directed.

GM impeller seal ring (neck ring) as per existing suitable for 10.0-12.5HP submersible pump sets complete all as directed.

Stainless steel running sleeves (off sizes) as per existing suitable for 10.0-12.5HP submersible pump sets complete all as directed

Impeller locking keys stainless steel (off sizes) as per existing suitable for 10.0-12.5HP submersible pump sets complete all as directed

Pump shaft 25.4mm dia stainless steel as per existing suitable for 10.0-12.5HP submersible pump sets complete all as directed

GM impeller as per existing suitable for 30.0HP submersible pump sets complete all as directed.

Intermediate bowl as per existing suitable for 30.0HP submersible pump sets complete all as directed.

Bowl bush (rubber) as per existing suitable for 30.0HP submersible pump sets complete all as directed.

Bowl bush (gun metal) as per existing suitable for 30.0HP submersible pump sets complete all as directed.

GM impeller seal ring (neck ring) as per existing suitable for 30.0HP submersible pump sets complete all as directed.

Stainless steel running sleeves (off sizes) as per existing suitable for 30.0HP submersible pump sets complete all as directed

Impeller locking keys stainless steel (off sizes) as per existing suitable for 30.0HP submersible pump sets complete all as directed

Pump shaft 25.4mm dia stainless steel as per existing suitable for 30.0HP submersible pump sets complete all as directed

GM impeller as per existing suitable for 5.0-7.5HP submersible pump sets complete all as directed.

Intermediate bowl as per existing suitable for 5.0-7.5HP submersible pump sets complete all as directed.

Bowl bush (rubber) as per existing suitable for 5.0-7.5HP submersible pump sets complete all as directed.

Bowl bush (gun metal) as per existing suitable for 5.0-7.5HP submersible pump sets complete all as directed.

GM impeller seal ring (neck ring) as per existing suitable for 5.0-7.5HP submersible pump sets complete all as directed.

Stainless steel running sleeves (off sizes) as per existing suitable for 5.0-7.5HP submersible pump sets complete all as directed

Impeller locking keys stainless steel (off sizes) as per existing suitable for 5.0-7.5HP submersible pump sets complete all as directed

Pump shaft 25.4mm dia stainless steel as per existing suitable for 5.0-7.5HP submersible pump sets complete all as directed

PVC impeller as per existing suitable for 1.5-2.0HP submersible pump sets complete all as directed.

Intermediate bowl as per existing suitable for 1.5-2.0HP submersible pump sets complete all as directed.

Bowl bush (rubber) as per existing suitable for 1.5-2.0HP submersible pump sets complete all as directed.

Bowl bush (gun metal) as per existing suitable for 1.5-2.0HP submersible pump sets complete all as directed.

PVC impeller seal ring (neck ring) as per existing suitable for 1.5-2.0HP submersible pump sets complete all as directed.

Stainless steel running sleeves (off sizes) as per existing suitable for 1.5-2.0HP submersible pump sets complete all as directed

Impeller locking keys stainless steel (off sizes) as per existing suitable for 1.5-2.0HP submersible pump sets complete all as directed

Pump shaft 25.4mm dia stainless steel as per existing suitable for 1.5-2.0HP submersible pump sets complete all as directed

GM impeller as per existing suitable for 15.0HP submersible pump sets complete all as directed.

Intermediate bowl as per existing suitable for 15.0HP submersible pump sets complete all as directed.

Bowl bush (rubber) as per existing suitable for 15.0HP submersible pump sets complete all as directed.

Bowl bush (gun metal) as per existing suitable for 15.0HP submersible pump sets complete all as directed.

GM impeller seal ring (neck ring) as per existing suitable for 15.0HP submersible pump sets complete all as directed.

Stainless steel running sleeves (off sizes) as per existing suitable for 15.0HP submersible pump sets complete all as directed

Impeller locking keys stainless steel (off sizes) as per existing suitable for 15.0HP submersible pump sets complete all as directed

Pump shaft 25.4mm dia stainless steel as per existing suitable for 15.0HP submersible pump set complete all as directed

Thrust plate suitable for 10-12.5HP submersible pump set

Thrust plate suitable for 5-7.5 HP submersible pump set

Thrust plate suitable for 15 HP submersible pump set

Thrust plate suitable for 30HP submersible pump set

Dismantling/opening of monoblock/ centrifugal pump including induction motor of capacity 10.0-15.0HP after disconnecting all electrical connections and taking out the same from foundation for complete servicing with materials including cleaning, lath work of shaft, re-assembling & re-installation of the same on existing foundation including making all electrical connections and testing on completion complete with replacement of the following items/parts:-

M&L for rewinding of motor with and including super enamelled copper winding wire of existing gauge & No of turns, re-insulating, two coats varnishing & heating including cutting and taking out existing burnt winding complete.

Replacement of all defective parts of pump set of existing size & make complete. Note:- All defective parts shall be measured and paid separately under respective item of Sch ‘A’ as supply only.

Dismantling/opening of monoblock/ centrifugal pump including induction motor of capacity 5.0 TO 7.5 HP after disconnecting all electrical connections and taking out the same from foundation for complete servicing with materials including cleaning, lath work of shaft, re-assembling & re-installation of the same on existing foundation including making all electrical connections and testing on completion complete with replacement of the following items/parts:-

M&L for rewinding of motor with and including super enamelled copper winding wire of existing gauge & No of turns, re-insulating, two coats varnishing & heating including cutting and taking out existing burnt winding complete.

Replacement of all defective parts of pump set of existing size & make complete. Note:- All defective parts shall be measured and paid separately under respective item of Sch ‘A’ as supply only.

Supply only the following parts/ items of monoblock/ centrifugal pump set and bowl assembly for replacement of parts/ items under item Nos. 21 to 22 above complete all as directed:-

Ball bearing suitable for 10.0-15.0HP monoblock/ centrifugal pump set complete all as directed.

SS bush as per existing suitable for 10.0-15.0HP monoblock/ centrifugal pump set complete all as directed.

MS sleeves as per existing suitable for 10.0-15.0HP monoblock/ centrifugal pump set complete all as directed.

Ball bearing suitable for and upto 5.0 - 7.5 HP monoblock/ centrifugal pump set complete all as directed.

SS bush as per existing suitable for and upto 5.0-7.5 HP monoblock/ centrifugal pump set complete all as directed.

MS sleeves as per existing suitable for and upto 5.0-7.5 HP monoblock/ centrifugal pump set complete all as directed.

MS Impeller suitable for 5.0 -7.5 HP centrifugal/monoblock pump set complete all as directed.

MS Impeller suitable for 10.0 -15 HP centrifugal/monoblock pump set complete all as directed.

S&F in repairs 100mm dia pressure gauge of scale 0-15 kg/cm² with FI clamp of size 25x3mm & 15mm socket complete all as specified and directed.

Supply and laying or fixing or passing in well/ borewell in replacement, 1100 volts grade heavy duty, PVC insulated and PVC sheathed mutistranded copper conductor submesible cable of size 2.5sqmm 3 core flat including connection to submersible motor/ starter panel with & including necessary jointing materials if required and testing on completion complete all as specified and direced.

Supply and laying or fixing or passing in well/ borewell in replacement, 1100 volts grade heavy duty, PVC insulated and PVC sheathed mutistranded copper conductor submesible cable of size 6.0sqmm 3 core flat including connection to submersible motor/ starter panel with & including necessary jointing materials if required and testing on completion complete all as specified and direced.

Supply and laying or fixing or passing in well/ borewell in replacement, 1100 volts grade heavy duty, PVC insulated and PVC sheathed mutistranded copper conductor submesible cable of size 10.0sqmm 3 core flat including connection to submersible motor/ starter panel with & including necessary jointing materials if required and testing on completion complete all as specified and direced.

S&F MS nuts, bolts and washers etc of required shape & size complete all as specified and directed.

S&F in replacement wall mounted cubical type panel board with locking arrangement and comprising of starter, capacitor, volt meter, indicator lamp, Amp meter & MCB/cut out of capacity suitable for upto 2.0 HP single phase submersible pumping set including fixing arrangement complete all as specified and directed.

S&F in repairs MU-G05H DOL starter of relay range 14-24 Amps of capacity suitable for 05.0 HP motor, AC-3duty, 415 volts, 50 Hz, three phase including fixing arrangement complete all as specified and directed.

S&F in repairs MU-G10H DOL starter of relay range 28-42 Amps of capacity suitable for 10.0 HP motor, AC-3duty, 415 volts, 50 Hz, three phase including fixing arrangement complete all as specified and directed.

S&F in repairs MU-G20H fully automatic star- delta starter of relay range 38-52 Amps of capacity suitable for and upto 20.0 HP motor, AC-3duty, 415 volts, 50 Hz, three phase including fixing arrangement complete all as specified and directed.

S&F in repairs MU-G30H fully automatic star- delta starter of relay range 45-65Amps of capacity suitable for and upto 30.0 HP motor, AC-3duty, 415 volts, 50 Hz, three phase including fixing arrangement complete all as specified and directed.

S&F in replacement fully automatic Star-Delta motor starter in sheet steel enclosure type ML-4 FASD suitable for motor rating AC-3 duty , 415 V, 3 phase, 50 Hz, upto 50 HP, relay setting 58 to 95 Amps Cat No-SS90730 Make- L&T or equivalent/C&S

S&F in replacement fully automatic Star-Delta motor starter in sheet steel enclosure type ML-6 FASD suitable for motor rating AC-3 duty , 415 V, 3 phase, 50 Hz, upto 75 HP, relay setting 90 to 140 Amps Cat No-SS90913 Make- L&T or equivalent/C&S

Supply and fixing in repairs MS well cap on the top of PVC/MS casing pipe of dia 200/ 250mm, internal threaded with locking arrangemnt including making provision for passing of 80/ 100mm dia column pipe thorough as required at site complete all as specified and directed.

Supply and lowering in replacement submersible pump set of capacity 5 HP,3 phase,50 Hz, 240 LPM at 57 Mtr Head, delivery size 50mm, stage 11 complete all as specified and directed. Make- kirloskar Model No-KS6B-0511 pr equivalent in Crompton/KSB

M&L for sign board in replacement of size 1200mmx1000mm made out of MS sheet of 16 SWG including preparation of both side surfaces and applying two coat of synthetic enamel paint over a coat of red-oxide primer and after painting/ prepration of surfaces, write the name of office & area location on both side with and including radium film sticker letters & numbers as required including fixing the sign board on MS framed structrue with & including suitable size nuts/ bolts/ screws complete all as specified and directed. Notes:- (i) Size of radium film sticker letters & numbers shall be as approved by Engineer-in- Charge.. (ii) M&L for MS framed structure shall be measured and paid separately under respective item of Sch'A'.

M&L for making of computerised colour/ printed layout plan and brief details i.e history of installation/ machinery of various installations on and including 1.0mm thick plastic laminated acrylic sheet of size 1500x1200mm fixed to new hard boards with & including PVC beading of suitable size fixed to all edges of board with & including mild steel screws of suitable size complete all as specified and directed. Note:- Details i.e layout plan and brief details shall be provided by Engineer-in-Charge separately during execution.

M&L for mild steel in replacement conforming to Fe-290 (Gde E-165) in framed work for supporting/ fixing of sign boards/monoblock pumpset and similar work including necessary welding, cutting/ making holes of required size & shape for supporting/ fixing of monoblock/sign board complete all as specified & directed.

M&L for PCC (1:2:4) type B-2 using 40 mm graded stone aggregate as in foundation, filling, mass concrete for fixing of MS framed structrue including necessary excavation and earth work complete all as specified & directed.

M&L for PCC1:2:4 type B1 20 mm grded stone aggrergate as in foundation filling and mass concrete complete all as specified and directed.

Supply only O- Tolidine chemical in 500ml pack. Make Qualigens or equivalent

Supply only residual chlorine kit for testing of chlorine content in water.

Supply and fixing in replacement PVC insulated multistranded copper conductor cable of size 25 sqmm single core electric panel board complete all as directed.

Supply and fixing copper lugs suitable for 25 sqmm cable

Supply and laying PVC flexible pipe of size 50sqmm complete all as directed.

M&L for painting of centrifugel motor pump set of capacity 60/75 HP with two coat of gray enemalled paint after scraping old paint including writing SM/MES No on pump/Motor with white colour complete all as directed.Note: letter size should not less than 20 mm in height.

M&L for painting of centrifugel motor pump set of capacity 40 HP with two coat of gray enemalled paint after scraping old paint including writing SM/MES No on pump/Motor with white colour complete all as directed. Note: letter size should not less than 20 mm in height.

M&L for painting of centrifugel/monoblock motor pump set of capacity 7.5-15 HP with two coat of gray enemalled paint after scraping old paint including writing SM/MES No on pump/Motor with white colour complete all as directed.

S&F in repairs 15 mm bore PVC gate valves, ISI marked, screwed both ends for iron pipe complete all as specified and directed.

S&F in repairs 15 mm bore PVC pipe including necessary fittings ( ie socket, bend etc) ISI marked, complete all as specified and directed.

S&F in repair/replacement pressure switch suitable for existing pressure booster pump of 0.6/ 1 HP complete all as specified and directed.

S&F in replacement monoblock pump set of cap 1.0 HP including all necessary connection complete all as directed.

Supply and lowering in replacement submersible pump set of capacity 1.5 HP,single phase,50 Hz, 70 LPM at 57 Mtr Head, delivery size 32mm,stage 13 complete all as specified and directed. Make- kirloskar Model No-KP4-0713S pr equivalent in Crompton/KSB

S&F MCCB 4 Pole Thermal adjustable breaker and adjustable Magnetic type complete all as specified and directed of following capacity

250 AMP, 36 KA

400 AMP, 36 KA

S&F MCCB 4 Pole Thermal adjustable breaker type complete all as specified and directed of following capacity

63 AMP, 25 KA

125 AMP, 25 KA

160 AMP, 25 KA

Dismantling of dozing pump for carrying out comprehensive/ preventive/ repairing work, checking rectifying defects as assured in day to day operation for overhauling required, refitting and reinstalling the plant after replacement of defective parts including testing etc complete including checking electrical system and day to day maintenance of plants requried at water supply installation by a skilled tradesman complete all as specified and directed. Notes:- i. Spares parts requried shall be mearured & paid separately under respective items. ii. Only those plants shall be measured and paid which will be repaired by providing several major defective items/ parts. iii. The quoted cost shall be deemed to be included for complete checking of dozing pumps installed at different locations.

Supply only following parts for dozing pumps of any make at site :-

Gear motor suitable for 230 Volts, 50 Hz, AC supply of existing model complete all as directed.

Rotor assembly with bearing brackets and tolerance rings of existing model complete all as directed.

Coil 250V, 50 Hz of existing model complete all as directed.

Single head feed rate control with shaft of existing model complete all as directed.

07 Pump head complete set (Ferrules 1/4" and Duckbill) of existing model complete all as directed.

Roller assembly of existing model complete all as directed.

7 Pump tube of existing model complete all as directed.

Injecter check valve 3/8" of existing model complete all as directed.

3/8" white suction/ discharge tubing of existing model complete all as directed.

Check valve duck bill of existing model complete all as directed.

Connecting nut 3/8" of existing model complete all as directed.

Ferrule 1/4" of existing model complete all as directed.

FRP dozing tank of existing model of capacity 100 Ltr having port hole for passing chlorine including provision for mounting motor and level gauge complete all as directed.

Vertical turbine agitator motor of capacity 1/4 HP suitable for 230 Volts, 50 Hz of existing model complete all as directed.

PVC weighted suction line strainer 3/8" of existing model complete all as directed.

Riveting screw of existing model complete all as directed.

Complete shaft with impeller of existing model complete all as directed.

Screws of existing model complete all as directed.

Ring Seal of existing model complete all as directed.

Ball ( Part No RDC08202 ) of existing model complete all as directed.

Suction Valve of existing model complete all as directed.

Discharge Valve of existing model complete all as directed.

Tubing Connector of existing model complete all as directed.

Tubing of existing model complete all as directed.

Foot Valve of existing model complete all as directed.

Antisyphon Valve of existing model complete all as directed.

Diaphram of existing model complete all as directed.

Oil Seal of existing model complete all as directed.

Spring of existing model complete all as directed.

S S Shaft of existing model complete all as directed.

Retainer Plate of existing model complete all as directed.

Solenoid Coil of existing model complete all as directed.

Stroke Control Shaft of existing model complete all as directed.

Electronic Module of existing model complete all as directed.

Pump housing of existing model complete all as directed.

Dozing Head of existing model complete all as directed.

Spacer of existing model complete all as directed.

NOTE:- Contractor will responsible to carry out testing of chlorination water of different location as required by SHO / User and testing report will be produced to Engineer-in-Charge on daily basis after taking signature by SHO or his rep. No extra payment shall be made on this account.

S & F Piano type socket 3/5 pin, 5 Amps, 230 Volts of existing model complete all as directed.

S & F in repair Piano type switch, 5 Amps, 230 Volts of existing model complete all as directed.

S & F in repair Plug top, 5 Amps, 230 Volts of existing model complete all as directed.

S & F in repairs nylone pipe 15 mm bore , heavy duty, complete all as specified and directed.

M&L for rewinding of electric motor 1 phase 230 volts, 1/4-1/2 HP with and including super enamelled copper winding wire of superior quality of existing size/ gauge & No of turns with and including of material such as varnish, cotton tapes, bush/bearings etc including cutting and taking out existing burnt/ short circuited winding wires complete all as directed.

S&F four pole off load change over switch of capacity 100 Amps, 415 Volts with side handle operated in sheet metal enclosures, powder coated, weather proof confirming to IS-13947-(Part-3)1993 complete all as specified and directed Make- HPL/L&T/Standard as approved by GE.

S&F four pole off load change over switch of capacity 200 Amps, 415 Volts with side handle operated in sheet metal enclosures, powder coated, weather proof confirming to IS-13947-(Part-3)1993 complete all as specified and directed.

S&F in replacement 70 watt LED, energy saving, enevironment friendly, long life exclusive innovating dia cast aluminium IP-66 protection, flood light suitable for highway lighting and general purpose including fixing arrangement and fixed on Overhead tank`s pillar/pump house complete all as directed. Make- Havells cat No- JETANEOFL 70WLED757LT G or equivalent in Bajaj/Crompton Greaves

S&F in replacement New generation, energy saving, environmental friendly, long life aesthetically designed aluminium landscape luminaire IP -65 of height 1.0 mtr for diffused lighting with high power LED as light source. including fixing arrangement complete all as directed. Make- Havells cat No-BAMBOOBL8WLED857SSYMTOPCM (1.0M) or equivalent in Bajaj/Crompton Greaves

S&F in replacement New generation,IP-65 post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source. including fixing arrangement complete all as directed. Make- Havells cat No-CORALPT35WLED757PSYMTOPC or equivalent in Bajaj/Crompton Greaves

S&F in replacement 70W New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 with 10KV Built-in Surge Protection Device. and general purpose including 1.5 mtr long bracket with clamp and ut bolt for fixing arrangement and fixed on Overhead tank`s pillar/pump house complete all as directed. Make- Havells cat No- ENDURAPEARLPLUSSL70WLED757PASYTOPC or equivalent in Bajaj/Crompton Greaves

Design, supply, erection, testing and commissioning of indoor type LT panel Box made of CRCA MS SHEET and M.S. Channel Base Frame mounted of suitable size, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos Aluminium bus bars of rating 800 amps, Provision of Spreader link to both incoming & Outgoing MCCBs for termination of cables . The LT panel shall be duly fabricated in a approved / certified factory / fabrication House who posseses type test certificate from CPRI for similar type of LT panel and having modern fabrication and testing facility which includes atleast seven (07) tanks pre treatment facility comprising of de-greasing, rinsing, de-rusting, rinsing, phosphating, rinsing and passivation followed by powder coated painting (thickness not less than 80 Micron) with approved shade of RAL 7032 (SIEMENS GRAY). The LT panel shall be provided with suitable rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The LT panel shall be made out of 2.00mm thick CRCA MS sheet and 2.00mm thick gland plate and having compartmentalized construction for individual switchgears and Bus Bars and having front opening facility and rear opening facility with single layer shutter with locking facility and mild steel channel (MC-75) base frame at bottom, suitable for mounting on the brick pedestal through grouting bolt, The panel board shall be provided with ventilation facility in the form of louvers for better heat dissipation. The LT panel shall be comprising of the followings :- Location : Main boosting panel no 1.

PROVISION FOR CABLE ENTRY :- The provision for cable entry / exit shall be provided in the bottom for both incoming and outgoing cables. BUS BARS & INTERNAL CONNECTIONS :- The bus bars should be made of Aluminium, duly insulated with 1100 volts grade standard colour coded heat shrink type PVC sleeves and rigidly mounted on suitable size 'F' class insulators of non hygroscopic non combustable, track resistant, high strength FRP / SMC / DMC material. 4 Nos Aluminium bus bars of rating 800 amps, . For all internal connections from main bus bars to switch gears shall be carried out with heat shrink type PVC insulated aluminium flats of suitable size and from bus bars to MCBs with suitable size FRLS PVC insulated multi flexible type copper wires as per the current carrying capacity of individual switch gears. Earthing bar shall be provided as per standard practice and shall be made of Galvanized Steel flats of size 25mm x 6 mm INCOMING :- (i) 4 pole MCCB ( with panel mounted rotary handle ) having breaking capacity 35 KA microprocessor based ICS=ICU = 100%, Fixed magnetic and adjustable thermal setting from 80% to 100% and of rating 630 Amps-01 No.

Design, supply, erection, testing and commissioning of indoor type LT panel Box made of CRCA MS SHEET and M.S. Channel Base Frame mounted of suitable size, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos Aluminium bus bars of rating 400 amps, Provision of Spreader link to both incoming & Outgoing MCCBs for termination of cables . The LT panel shall be duly fabricated in a approved / certified factory / fabrication House who posseses type test certificate from CPRI for similar type of LT panel and having modern fabrication and testing facility which includes atleast seven (07) tanks pre treatment facility comprising of de-greasing, rinsing, de-rusting, rinsing, phosphating, rinsing and passivation followed by powder coated painting (thickness not less than 80 Micron) with approved shade of RAL 7032 (SIEMENS GRAY). The LT panel shall be provided with suitable rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The LT panel shall be made out of 2.00mm thick CRCA MS Sheet and 2.00mm thick gland plate and having compartmentalized construction for individual switchgears and Bus Bars and having front opening facility and rear opening facility with single layer shutter with locking facility and mild steel channel (MC-75) base frame at bottom, suitable for mounting on the brick pedestal through grouting bolt, The panel board shall be provided with ventilation facility in the form of louvers for better heat dissipation. The LT panel shall be comprising of the followings :- Location : Main boosting panel no 2

PROVISION FOR CABLE ENTRY :- The provision for cable entry / exit shall be provided in the bottom for both incoming and outgoing cables. BUS BARS & INTERNAL CONNECTIONS :- The bus bars should be made of Aluminium, duly insulated with 1100 volts grade standard colour coded heat shrink type PVC sleeves and rigidly mounted on suitable size 'F' class insulators of non hygroscopic non combustable, track resistant, high strength FRP / SMC / DMC material. 4 Nos Aluminium bus bars of rating 400 amps, . For all internal connections from main bus bars to switch gears shall be carried out with heat shrink type PVC insulated aluminium flats of suitable size and from bus bars to MCBs with suitable size FRLS PVC insulated multi flexible type copper wires as per the current carrying capacity of individual switch gears. Earthing bar shall be provided as per standard practice and shall be made of Galvanized Steel flats of size 25mm x 6 mm INCOMING :- (i) 4 pole MCCB ( with panel mounted rotary handle ) having breaking capacity 35 KA microprocessor based ICS=ICU = 100%, Fixed magnetic and adjustable thermal setting from 80% to 100% and of rating 250 Amps-01 No.

Design, supply, erection, testing and commissioning of indoor type LT panel Box made of CRCA MS Sheet and M.S. Channel Base Frame mounted of suitable size, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos Aluminium bus bars of rating 300 amps, Provision of Spreader link to both incoming & Outgoing MCCBs for termination of cables . The LT panel shall be duly fabricated in a approved / certified factory / fabrication House who posseses type test certificate from CPRI for similar type of LT panel and having modern fabrication and testing facility which includes atleast seven (07) tanks pre treatment facility comprising of de-greasing, rinsing, de-rusting, rinsing, phosphating, rinsing and passivation followed by powder coated painting (thickness not less than 80 Micron) with approved shade of RAL 7032 (SIEMENS GRAY). The LT panel shall be provided with suitable rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The LT panel shall be made out of 2.00mm thick CRCA MS sheet and 2.00mm thick gland plate and having compartmentalized construction for individual switchgears and Bus Bars and having front opening facility and rear opening facility with single layer shutter with locking facility and mild steel channel (MC-75) base frame at bottom, suitable for mounting on the brick pedestal through grouting bolt, The panel board shall be provided with ventilation facility in the form of louvers for better heat dissipation. The LT panel shall be comprising of the followings :- Location : officer mess p/h

PROVISION FOR CABLE ENTRY :- The provision for cable entry / exit shall be provided in the bottom for both incoming and outgoing cables. BUS BARS & INTERNAL CONNECTIONS :- The bus bars should be made of Aluminium, duly insulated with 1100 volts grade standard colour coded heat shrink type PVC sleeves and rigidly mounted on suitable size 'F' class insulators of non hygroscopic non combustable, track resistant, high strength FRP / SMC / DMC material. 4 Nos Aluminium bus bars of rating 300 amps, . For all internal connections from main bus bars to switch gears shall be carried out with heat shrink type PVC insulated aluminium flats of suitable size and from bus bars to MCBs with suitable size FRLS PVC insulated multi flexible type copper wires as per the current carrying capacity of individual switch gears. Earthing bar shall be provided as per standard practice and shall be made of Galvanized Steel flats of size 25mm x 6 mm INCOMING :- (i) 4 pole MCCB ( with panel mounted rotary handle ) having breaking capacity 35 KA microprocessor based ICS=ICU = 100%, Fixed magnetic and adjustable thermal setting from 80% to 100% and of rating 200 Amps-01 No.

Design, supply, erection, testing and commissioning of indoor type LT panel Box made of CRCA MS Sheet and M.S. Channel Base Frame mounted of suitable size, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos Aluminium bus bars of rating 300 amps, Provision of Spreader link to both incoming & Outgoing MCCBs for termination of cables . The LT panel shall be duly fabricated in a approved / certified factory / fabrication House who posseses type test certificate from CPRI for similar type of LT panel and having modern fabrication and testing facility which includes atleast seven (07) tanks pre treatment facility comprising of de-greasing, rinsing, de-rusting, rinsing, phosphating, rinsing and passivation followed by powder coated painting (thickness not less than 80 Micron) with approved shade of RAL 7032 (SIEMENS GRAY). The LT panel shall be provided with suitable rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The LT panel shall be made out of 2.00mm thick CRCA MS Sheet and 2.00mm thick gland plate and having compartmentalized construction for individual switchgears and Bus Bars and having front opening facility and rear opening facility with single layer shutter with locking facility and mild steel channel (MC-75) base frame at bottom, suitable for mounting on the brick pedestal through grouting bolt, The panel board shall be provided with ventilation facility in the form of louvers for better heat dissipation. The LT panel shall be comprising of the followings :- Location : map 4 area p/h.

PROVISION FOR CABLE ENTRY :- The provision for cable entry / exit shall be provided in the bottom for both incoming and outgoing cables. BUS BARS & INTERNAL CONNECTIONS :- The bus bars should be made of Aluminium, duly insulated with 1100 volts grade standard colour coded heat shrink type PVC sleeves and rigidly mounted on suitable size 'F' class insulators of non hygroscopic non combustable, track resistant, high strength FRP / SMC / DMC material. 4 Nos Aluminium bus bars of rating 300 amps, . For all internal connections from main bus bars to switch gears shall be carried out with heat shrink type PVC insulated aluminium flats of suitable size and from bus bars to MCBs with suitable size FRLS PVC insulated multi flexible type copper wires as per the current carrying capacity of individual switch gears. Earthing bar shall be provided as per standard practice and shall be made of Galvanized Steel flats of size 25mm x 6 mm INCOMING :- (i) 4 pole MCCB ( with panel mounted rotary handle ) having breaking capacity 35 KA microprocessor based ICS=ICU = 100%, Fixed magnetic and adjustable thermal setting from 80% to 100% and of rating 200 Amps-01 No.

Design, supply, erection, testing and commissioning of indoor type LT panel Box made of CRCA MS SHEET and M.S. Channel Base Frame mounted of suitable size, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos Aluminium bus bars of rating 300 amps, Provision of Spreader link to both incoming & Outgoing MCCBs for termination of cables . The LT panel shall be duly fabricated in a approved / certified factory / fabrication House who posseses type test certificate from CPRI for similar type of LT panel and having modern fabrication and testing facility which includes atleast seven (07) tanks pre treatment facility comprising of de-greasing, rinsing, de-rusting, rinsing, phosphating, rinsing and passivation followed by powder coated painting (thickness not less than 80 Micron) with approved shade of RAL 7032 (SIEMENS GRAY). The LT panel shall be provided with suitable rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The LT panel shall be made out of 2.00mm thick CRCA MS SHEET sheet and 2.00mm thick gland plate and having compartmentalized construction for individual switchgears and Bus Bars and having front opening facility and rear opening facility with single layer shutter with locking facility and mild steel channel (MC-75) base frame at bottom, suitable for mounting on the brick pedestal through grouting bolt, The panel board shall be provided with ventilation facility in the form of louvers for better heat dissipation. The LT panel shall be comprising of the followings :- Location : pts billet p/h

PROVISION FOR CABLE ENTRY :- The provision for cable entry / exit shall be provided in the bottom for both incoming and outgoing cables. BUS BARS & INTERNAL CONNECTIONS :- The bus bars should be made of Aluminium, duly insulated with 1100 volts grade standard colour coded heat shrink type PVC sleeves and rigidly mounted on suitable size 'F' class insulators of non hygroscopic non combustable, track resistant, high strength FRP / SMC / DMC material. 4 Nos Aluminium bus bars of rating 300 amps, . For all internal connections from main bus bars to switch gears shall be carried out with heat shrink type PVC insulated aluminium flats of suitable size and from bus bars to MCBs with suitable size FRLS PVC insulated multi flexible type copper wires as per the current carrying capacity of individual switch gears. Earthing bar shall be provided as per standard practice and shall be made of Galvanized Steel flats of size 25mm x 6 mm INCOMING :- (i) 4 pole MCCB ( with panel mounted rotary handle ) having breaking capacity 35 KA microprocessor based ICS=ICU = 100%, Fixed magnetic and adjustable thermal setting from 80% to 100% and of rating 160 Amps-01 No.

AGRA AND COMPANY

H.S.Kochhar n Sons

M/S SINGH ELECTRIC CO

M/s S.M. Construction

commercial construction