SPECIAL REPAIRS TO BUILDING NO T-28, T-21 AT MH AVADI AND PROVN OF WIRE MESH AND WINDOW FOR GUARD POST NO 1 TO GUARD POST NO 12 IN TECH AREA OF OD AVADI AND UPGRADATION OF TOILET AND BATHROOM AT BLDG NO T-01AT MH AVADI UNDER GE AVADI

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Glazed ceramic coloured tiles single 300x200mm x 6 to 7mm thick, as in vertical surfaces such as in skirting and dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 10mm thick back coat in CM 1:3, complete all as specified and directed.

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10mm thick screed bed in CM 1:4 complete all as specified and directed.

S&F in repairs Vitreous China squatting pan of 'Orissa' pattern of size 580 x 440mm, white, with integral foot rests, complete including provision of lime concrete bedding all as specified and as directed.

S&F in repairs 10 ltr capacity PVC valveless symphonic action type flushing cistern low level white with inlet ball valve, float and handle/push including brackets and PVC flushing pipe 32mm bore, complete all as specified.

S&F in repairs Vitreous China wash Basin (flat back or angle back type) , of size 550x400mm including brackets, waste coupling PTMT, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc, complete all as specified.

S&F in repairs Tubular towel rail, brass chromium plated 20mm dia D type, 60cm long between flanges, complete all as specified and directed.

S&F in repairs 125mm Chromium plated shower roses with or without swivel joints, including fixing to steel pipe or union

S&F PVC connection 15mm size with PTMT nuts of length 600mm,complete all as specified and directed.

S&F 15mm bore Pillar taps bore cast copper alloy, with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe, complete all as specified

S&F15mm bore Bib taps, cast copper alloy chromium plated with crutch or butter-fly handle screwed down, screwed for iron pipe or for brass ferrules, complete all as specified and directed.

S&F 15mm bore stop valve/Angle valve, chromium plated fancy type cast copper alloy, screwed down high pressure, with crutch or butter fly handle, screwed both ends for iron pipes or for unions and fixed of,complete all as specified and directed.

S&F in repairs 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe , all as specified and directed.

S&F 15mm bore stop valve, cast copper alloy, screwed down high pressure, with crutch or butter fly handle, screwed both ends for iron pipes or for unions and fixed of,complete all as specified and directed.

Taking down chowkats or frames exc 1.5Sqm and not exc. 4Sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed.

Taking down chowkats or frames not exc 1.5Sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm thick plain colour PVC sheet reinforced with 19mm MS square tube of 19 gauge mitre cut at two corners and joined by inserting two Nos of 150mm long brackets of 15mmx15mm MS square tube inside the 19mm MS square tube and suitably screwed complete all as specified and as directed.

S&F Factory made soild PVC profiled panel door shutter 28mm thick withintegral skin as frame & 3mm thick high pressure compact laminate on both side of approved colour as , with 'C type Gl or 40 x 20 x19 of MS pipe as stiffner & supplying & fixing in frame at site incl all fittings(handles/tower bolt/sliding bolt/hinges etc as per specifications & drawing.

S & F anodised aluminium powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F 4mm thick figured glass pin headed type and glazing with oil putty in squares not exc 0.5 sqm in each pane all as specified.

S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed

S&F 75mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 all as specified.

S&F 100mm long Aluminium handles, cast type, anodised, all as specified and directed.

S&F for 125mm length aluminum, anodised, barrel tower bolts of extruded section and fixed all as specified.

Taking up or down steel tubing 15mm and connections, all as specified.

Taking up or down steel tubing 20mm and connections, all as specified.

S & F 15mm bore Unplasticised PVC pipes including all fittings of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc.,complete and making good the area to match with existing surface, complete all as specified and as directed.

Ditto all as per item No. 31 above but 20mm outer dia.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement, all as specified and directed.

Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings all as specified and directed.

Dismantling timber scantling 40sqcm and over in section framed work, in any position,complete all as specified and directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides fixed with angle cleats or other connecting plates Fe-410-W (Gde-E-250) quality-B complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed wih self tapping screws as specified

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed wih self tapping screws as specified

Dismantling of ceiling board of any thickness. Including frame work all as directed.

S & F of aluminium snap grid false ceiling of panels of size 605 x 605mm using aluminium anodised wall angle of size 25 x 25 x 1.50mm thick fixed to walls with rawl plug and screws n. exc 1.50m c/c and intermediate panels using main "Tee" and cross "Tee" aluminium anodised section of size 35 x 25 x 1.50mm and 25 x 25 x 1.50mm thick suspended with and including 4mm dia GI wire n. exc 1.2m c / c and12mm thick Gypsum Board in ceiling with 1mm plain PVC Sheet fixed to aluminium frame work with screws complete all as directed.

S & F anodised powder coated aluminium window shutters , fixed type without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, etc. complete all as specified & directed.

S & F powder coated anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws, etc. complete all as specified & directed.

S&F in aluminium (Die cast) body door closer hydraulically regulated designation No.3 universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg & fixed complete all as specified & directed.

M & L for 12mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with scruwes to aluminium frame work shutter.etc all as specified and as directed by Engr-in-charge

S&F for 5.5mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.50 Sqm in each pane complete all as specified and as directed

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire taples Galvanised wire staples complete all as specified and as directed

S&F factory made solid PVC moulded door shutter with wood free EPS 28 to 30mm thick(styles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on front face and 2mm plain colour PVC sheet on backface, supplying and fixing in frame at site as per specification complete all as specified and as directed.

S&F 125mm long Aluminium handles, cast type, anodised, all as specified and directed.

S&F floor door stopper 150mm size of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor

S&F Aluminium Mortice lock, 4 levers vertical type size 100mm complete all as specified.

S&F aluminium die body Door closer hydrau lically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed.

S&F for framed work such as grills,gratings, hold fast etc., with ends of bars,framed guard bar, Iron doors etc., all as specified conforming to Fe-290, Gde E-165

Demolition of Brickwork of stone/boulder masonry, build incement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles

M&L Brickwork with fly ash Old size bricks straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L Rendering 15mm thick in CM 1:6 on other than fair faces of brick work or concrete surfaces on external surfaces finished even and fair all as specified and as directed.

Rendering 10 mm thick in cement mortar 1:6 on fair faces of brick wall or on concrete surfaces ,finished even and smooth, without using extra cement complete all as specified and as directed.

M&L for preparing new surface of wall and applying two coats of Oil bound Distemper over a coat of alkali resistant primer and 3mm putty on new plastered surface complete all as specified and as directed.

M & L for preparation of new plasterd surfaces of walls and applying two coats of cement base paint over a coat of primer all as specified and directed .

M & L Preparation of new steel surfaces over 10cm width or girth and painting with synthetic enamel painting two coats over a coat of primer all as specified.

Complete removal of existing treatment and treating with two coats of oil bound distemper over a coat of primer & 3mm putty to wall surfaces including preparation of old surface of wall all as specified

Complete removal of existing treatment and treating with two coats of cement base paint to walls surfaces over a coat of primer including preparation of old surface all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor or pavings n exc 15 cm thickness (below or above ground level) all as directed.

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base all as specified and as directed.

M&L for chequred cement concrete tiles mixed with grey cement and no pigment of size 300x 300 x25 mm thick set jointed and pointed in neat cement slurry in floors including 20 mm thick screed in CM 1:4 all as specified and as directed.

M&L for 50mm thick PCC 1:2:4, type B-1 using 20mm graded stone aggregated as in sub base all as specified and as directed.

M&L virified ceramic tiles 10mm thick light shade (Square/rectangular) polished, area of each tiles n.exc 0.36 Sqm, in floors over 15mm thick screed bed in CM 1:6 on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed.

ditto as per item No 72 above but in vertical surface (dado/skirting) to match the shade of floor tiles laid over and including 10mm thick back coat in CM 1:3 ,complete all as specified and directed.

M&L for Non-skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,over 15mm thick screed bed in CM 1:6 on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed.

M&L 75 mm thick for PCC 1:3:6, type C2 & using 40mm graded stone aggregate as in plinth protection complete all as specifed and directed

S&F rotational moulded polyethylene water storage tank capacity 750 litres consisting of three layer cylindrical vertical with top closed hoisted and fixed in position inluding dismantling of old water tanks all as specified and directed.

S&F 20 mm dia Ball valves ,high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule all as specified and directed.

S&F in repair bib taps 15mm bore standard of PTMT (minimum wt 90 gms) any colour high pressure screwed for iron pipe and fixed all as specified

S&F in repair 15mm bore stop valve of PTMT (minimum wt. 90gms) any colour high prssure screwed for iron pipe and fixed all as specified.

S&F in repair 15mm bore angle stop valve of PTMT (minimum wt. 90gms) any colour high prssure screwed for iron pipe and fixed all as specified .

S&F towel rail 450 mm long of PTMT ( min wt 170 gms) fixed with and including chromium plated brass screw and wooden / plastics cleats all as specified

S&F 75 mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement all as specified.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern) white(excluding flushing cistern and flush pipe) including connection to drain or out going pipe and flush pipe anti symphonize pipe etc complete all as specified and as directed.

S&F in 32mm dia waste coupling of PTMT (half or full thread) min wt 40gms all as specified and as directed.

S&F 15mm pillar taps of PTMT (min wt 15mm-110gms) any colour screwed for iron pipe and fixed all as specified.

S&F in repairs 75 mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints laid in trenches or in floors all as specified

S&F in repairs 75 mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints fixed to wall all as specified

S&F 75 mm bore. PVC (SWR) bends any radius all as specified and as directed.

S&F in repairs 110mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints laid in trenches or in floors all as specified

S&F in repairs 110mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints fixed to wall all as specified

S&F 110 mm PVC (SWR) bend any radius all as specified

S&F 110mm bore.PVC(SWR) junction single (single T) equal or unequal with access door all as specified.

S&F in repair 32 mm bore of pipe low density polythene pipe (LDPE) of pressure rating 6Kgf/sqcm fixed to wall or laid in floor etc including fittings complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc all as specified.

M&L for machine cut mirror polish kota stone slab flooring 20-25mm thick over 15mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including round nosing at corners ,rubbing and mirror polishing complete as specified and as directed.

M&L for 20mm thick granite stone slab machine cut, bedded over 15mm thick (1:4) cement mortar scree and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete as directed

Demolition and breaking up of existing SWG pipe 150mm dia alongwith packing and haunching concrete and removing debris all as specified.

-ditto- but 200mm dia pipe.

Demolition of RCC broken cover slabs in manholes/shelfs in any position and removing the debris off complete all as specified. Note:- Reinforcement cut as required to facilitate demolition.

M & L for pre cast cover slab in RCC 1:2:4, type B1, using 20mm graded stone aggregate for manhole, platform, shelfs etc set in cement mortar 1:6 including necessary form work complete all as specified. Note : Reinforcement will be measured and paid separately.

M & L for TMT bars 8mm dia cut to length, bent to shape required including hooking ends and binding with mild steel wire not less than 0.9mm dia as in reinforcement complete all as specified.

M & L for TMT bars 10mm dia and over cut to length bent to shape as required including cranking, bending, binding with mild steel wire annealed not less than 0.9mm dia as in reinforcement complete all as specified.

M & L for providing PCC 1:3:6, type C1 using 20mm graded stone aggregate as in coping including weathering, slightly rounded or chamfered angles and throating including formwork complete all as specified.

M & L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick / concrete surfaces and finished even and fair without using extra cement all as specified.

M & L 150mm reinforced concrete pipes, class NP2, laid and jointed complete with collars ect complete all as specified and directed.

All as per Item No. 104 above, but for 200mm dia pipe

M & L for PCC 1:3:6 type C2 using 40mm graded stone aggregate for concrete bed to drain pipe including packing under and haunching against the sides of pipes laid and tested for 150mm dia pipes, all as specified.

All as per Item No. 85 above, but for 200mm dia pipe

S & F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified etc.

S & F powder coated anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws, etc. complete all as specified.

S&F for second class hard wood plain, solid, straight, chowkats and frames, wrought framed rebated on the solid, rounded or chamfered put together with glue pinned complete all as specified and as directed.

M&L for PCC 1:3:6 type C-1 using 20 mm graded stone aggregate for fixing in hold fast complete all as specified.

M & L for preparing and treating ends of posts, back of chowkats with coal tar black paint, area tarred exc. 0.10 sqm but not exc. 0.50 sqm all as specified and as directed.

M & L for preparing and treating small articles such as hold fasts with coal tar black paint, area tarred not exc. 0.10 sqm all as specified and as directed.

M&L forming jambs etc to openings (to forgoing items) incl cutting , toothing and properly bonding into old work also facing, jointing and pointing to match existing work in Cement mortar 1:6 or cement lime mortar 1:1:8 complete all as specified.

Supply and fix 35mm thick, 2nd class hard wood, plain, framed, panelled shutters (any number of panels), with panels of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats complete all as specified and directed.

Supply and fix 35mm thick, 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc.(without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc; size of members of shutters as specified in SSR part I, section 8, clause 8.24(a); supplied and fitted to chowkats complete all as specified and directed.

M & L Preparation of new wood surfaces of any description over 10cm width or girth and painting with two coats of synthetic enamel painting over a coat of pink primer all as specified.

S&F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks,or galvanised wire staples complete all as specified and as directed

S&F 100mm size, butt hinge medium weight cold rolled mild steel & fixed complete all as specified & directed.

S&F 300 mm long Aluminium alloy anodised sliding door bolts with hasp and staple(bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium and fixed.

S&F for 150mm length aluminum, anodised, barrel tower bolts of extruded section and fixed.

S&F 150mm size aluminum handles, cast type anodised complete all as specified & directed.

S & F 300mm ordinary rat rail rod pattern springs including roller and roller plate complete all as specified & directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 Sqm.m in each pane.

Taking down carefully unserviceable point wiring copper / aluminium (light, fan, socket or power) complete, including removal of batten / conduit / gutties / wooden board etc., including fittings and fixtures such as switches, ceiling roses, regulators, sockets, light fittings, fans etc., removal from site under Sch of credit and removal of unserviceable items out of site and making good the disturbed surfaces of walls, ceilings etc., complete all as specified and as directed.

S & F point wiring on stone / brick masonry wall complete with two 1.5 sqmm single core PVC insulated FRLSH ,1100 volts grade unsheathed cable confirming to IS-694, 1977 with multistranded copper conductor, drawn through and including non-metalic rigid PVC conduit, conduit fittings and conduit accessories not less than 20 mm dia fixed to wall/ceiling/trusses with all accessories etc and including provision of one 1.5 sqmm PVC insulated single core multistranded copper conductor FRLSH green in colour as earth continuity conductor and connected to common earth dolly, including pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet, 60mm deep, concealed in walls, duly painted with two coats of anti-corrosive over a coat of red oxide zinc chrome primer and covered with bakelite hylam sheet cover 3mm thick fixed with cadmium plated screws for housing the switches, socket outlets, fan regulators etc., complete all as specified and as directed fo the following

one light point controlled by one switch.

One Exhaust fan point controlled by one switch.

One ceiling fan point controlled by one switch and regulator

One switch socket outlet 3 pin 5 Amps on same board along with other switches

One switch socket outlet 3 pin 5 Amps on independent board.

All as per item No 119 here-in-before but for point wiring with two 4.0 sqmm single core copper conductor multistranded FRLSH cable and one 4.0 sqmm PVC insulated single core multistranded cable as earth continuity conductor green in colour for one 3 pin switch socket outlet, 15 Amps, on independent board complete all as specified and as directed.

S&F Switch piano flush type, single pole,5 Amps, 240 volts complete all specified.

S&F Switch socket 3 pin 5 amps , multi pin , flush type,complete all specified.

S&F Switch socket 3 pin 15 Amps, multipurpose, flush type complete all specified.

S&F ceiling rose 65 X 50 mm , three terminals ,bakelite , surface complete all specified.

S&F MCB single pole 6-40 Amps, 230V complete all as specified.

S&F MCB SPN 40Amps, 230V complete all as specified.

S&F Surface and wall mounted LED tube light fitting, 20 W, batten type, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver complete with all accessories , suitable for operation on AC, single phase 220 / 230 Volts , 50 Hz supply, and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting complete all as specified and as directed. Make : C&S Nakshatra/20W Catpart No :LTTB4F20WLED/W and equivelent in Havells ;- Lumlineplus Catpart No - LUMILINEPLUSBS20WLED865SPCSS Crompton :- BRIGHT LINEA Catpart No :- CCS-100-20-65-HL2-DP-NWH

Supply and fix Surface and wall mounted LED tube light fitting 10W, batten type(2 feet), extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete with all accessories , suitable for operation on AC, single phase 220 / 230 Volts , 50 Hz supply complete all as specified. Make : C&S Nakshatra/10W Catpart No :LTTB2F10WLED/W and equivelent in Havells ;- Lumlineplus Catpart No - LUMILINEPLUSBS18WLED865SPCSS, Suriya :- Catpart No :- SLE BT 10

S&F MCB DB SPN 8 way, double door, powder coated, 240 volts, AC, 50Hz, IP 43 protected, with provision for MCB double pole as incomer and SP MCBs as outgoing with tinned copper bus bar, neutral link, earth link and connecting up complete all as specified and as directed. Note : Incoming and Outgoing MCB measured separately relevent items.

S&F for lightduty Exhaust fan 300mm sweep with lovers all fitting accessories including surface and wall modification for fixing of exhaust fan complete all as specified. Make :-Usha and equivlant Almonard/Crompton

S & F Point wiring on stone / brick masonry wall complete with two 1.5 sqmm single core PVC insulated FRLSH ,1100 volts grade unsheathed cable confirming to IS-694, 1977 with multistranded copper conductor, drawn through and including non-metalic rigid PVC conduit, conduit fittings and conduit accessories not less than 20 mm dia concealed in walls and fixed with suitable clamps on ceiling / roof trusses etc., and including provision of one 1.5 sqmm PVC insulated single core multistranded copper conductor FRLSH green in colour as earth continuity conductor and connected to common earth dolly, including pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet, 60mm deep, concealed in walls, duly painted with two coats of anti-corrosive over a coat of red oxide zinc chrome primer and covered with bakelite hylam sheet cover 3mm thick fixed with cadmium plated screws for housing the switches, socket outlets, fan regulators etc., complete all as specified and as directed for the following:- Note : Cost of terminal box and cutting chases for concealing pipes is deemed to be included in the item rates quoted for point wiring.

one light point controlled by one switch.

One Exhaust fan point controlled by one switch.

One ceiling fan point controlled by one switch and regulator

One bell / buzzer point controlled by one bell push

One switch socket outlet 3 pin 5 Amps on same board along with other switches

One switch socket outlet 3 pin 5 Amps on independent board.

All as per item No 131 here-in-before but for point wiring with two 4.0 sqmm single core copper conductor multistranded FRLSH cable and one 4.0 sqmm PVC insulated single core multistranded cable as earth continuity conductor green in colour for one 3 pin switch socket outlet, 15 Amps, on independent board complete all as specified and as directed.

S&F Bell push, flush type, single pole, 5 Amps, 240 volts complete all specified.

S&F electronic fan regulator, flush type phenolic laminated sheet etc; as required.

S&F Bell , ding-dong type , AC, 215 volts, 50 HZ complete all as specified.

Supply and Fixing of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified.(Through submain wiring)

Supply and fix Surface and wall mounted LED Bulk head fitting 10W,extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete with all accessories , suitable for operation on AC, single phase 220 / 230 Volts , 50 Hz supply complete all as specified. Make :C&S :- SIRUS /10W cat part No :- LTB10WLED / Luker :- LBKOVSL04/ Bajaj:- BIBWP10WLED

S&F LED building security light fitting 25W made up of pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07, complete pre-wired and connecting up with suitable twin core flexble copper wire including provision of necessary GI tubing medium grade 25mm bore of pipe 1.5 bent to shape with necessary clamps made out of mild steel, nuts and bolts etc., including two coats of synthetic enamel paint over a coat of red oxide primer on exposed steel surface for fixing the fitting to Bldg etc complete all as specified and as directed. Make : Havells (ENDURAPEARLSL25WLED757SASYTOPCMP) / Bajaj:- PCLST25LED/V2/ Crompton:- LSTS-25-CDL/M.

Supply and Fixing of Rigid non-metallic PVC conduit for 25mm dia exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc concealed in walls and fixed with suitable clamps on ceiling / roof trusses etc with suitable TV socket box complete all as specified.

Taking down carefully Power / Sub main wirings with PVC aluminum conductor cables in PVC/STEEL conduits / TW battens up to 2 runs of 6 Sq.mm removing materials from site, taken as credit , making good the disturbed surfaces all as specified and as directed.

S&F Power / Sub-main wiring with PVC insulated unsheathed, FRLSH ,1100 volts, grade multistranded copper conductor, two runs of single core 6 sqmm conforming to IS-694, drawn through and including suitable dia rigid PVC conduit, conduit fittings and conduit accessories alongwith one run 6 sqmm PVC insulated single core multistranded copper conductor cable (green) as earth continuity conductor concealed in walls and fixed with suitable clamps on ceiling / roof trusses etc. and connecting to common earth dolly complete all as specified and as directed.

M&L for wiring for circuit / power /sub main with four runs of single core 10 Sqmm size and two run of single core10.0 Sqmm (green colour as earth continuity conductor) PVC insulated, FRLSH unsheathed, muilti stranded copper conductor cable drawn through and and including PVC conduit suitable dia for four runs of 10 sqmm submain wiring with complete fixing accessories complete all as specified.

S&F Load line MCB DB TP&N 4 way, vertical, double door, powder coated, 415 volts, AC, 50Hz, IP 54 protected, fixed on wall semi flush with provision for FP MCCB 100 Amps as incomer and SP MCBs 40 / 63 Amps as outgoing with tinned copper bus bar, neutral link, earth link and connecting up complete all as specified and as directed. Note : Incoming MCCB and Outgoing MCB measured separately relevent items.

S&F MCCBs100 Amps 415V,16KA, 4 Pole complete all as specified .

Supply and fixing ceiling fan 1200mm sweep with star rating,high speed capacity ,energy saving ceiling fan,ISI marked complete with suitabe down rod, 230 volts (single phase) and provisioning of flexible copper cord of size 23/0.0076 of required length from ceiling rose or connector to ceiling fan for giving connection with suitable clamps,fastner and accessories complete all as specified and as directed. Make :-Usha Model:- Energy Saving Ceiling fan 1200MM ENERGIA ISI and equivlant Havells/Crompton

S&F for heavyduty Exhaust fan 300mm sweep turbo force model with louvers and all fitting accessories including surface and wall modification for fixing of exhaust fan complete all as specified. Make :-Usha Model No :- 300mm S.PH TURBO HDEF 1400RPM ISI and equivlant Almonard/Crompton

Material and labour for earth continuity conductor or main earthing lead fixed to valve on batten or recess or chases or burried in ground or drawing in conduit or any other situation for loop earthing etc as reqd 4 mm dia galvanized steel wire all as specified and directed by Engr-in-Charge

Earthing complete with galvanised iron earth plate electrode 600mm X 600mm X 6mm thick, with and including earthing of 4mm dia GI wire protected by 15mm dia GI pipe light grade upto a length of 7.5m. The plate shall be buried directly in ground vertically to a depth not less than 2.25 metres below ground level with top edge of the earth plate at a depth not less than 1.5 metres below ground level, connected to earth lead as described here-in-before by means of bolts, nuts, washers and checknuts made out of galvanised iron or mild steel, earthing lead protected by as described here-in-before and connected to main switch board or main control board or electric pole all as shown on electrical plate No.3 of MES Sch Part-I including necessary earth work and excavation in any type of soil, plain cement concrete 1:3:6, type C1 chamber, reinforced cement concrete cover slab with locking arrangement and handle of 10mm dia MS round bars 450mm long, 1:2:4 type B1, 50mm thick with 8mm dia TMT bars at 140mm centre to centre both ways, GI pipe of bore 20mm medium grade for watering with funnel, wiremesh, salt, charcoal, lugs including testing complete all as specified and as directed.

Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning of MCB TPN 40 To 100 Amp complete all as specified.

S&F Triple pole and earth encolsure with a three pin and earth plug with socket complete with one triple pole MCB 63 Amps complete all as specified. (Through submain wiring)

Taking down ceiling fan 1200mm sweep, dismantling and opening up, removing burnt up, unserviceable copper winding and insulating materials, cleaning and rewinding with super enamelled copper conductor winding of same existing gauge and type of insulation including necessary insulating materials, sleeves etc., replacing bearings, bushes, condensors of same existing type and capacity, assembling back, painting, testing and writing MES No.20mm height with synthetic enamel paint black complete including rehanging of ceiling fan with all accessories complete all as specified and as directed.

Taking down unserviceable Eahaust fan from site and re-fixing in position duly rectifying the defects (replacing of ball and bearing, oiling / greasing,winding etc.) and make it serviceable in all respect including painting and marking MES No complete all as specified and as directed by Engineer in Charge.

PSK Enterprises

bhakthavatsalam builders