GE(S)BTD/TOKEN25/2021-22 SPACIAL REPAIR TO BUILDING NO T-1027 AND T-1029 OR LIVING LINE ALONGWITH CERTAIN MINOR REVENEW AND LBW WORKS UNDER AGE B/R-II AND E/M-IV OF GE(SOUTH) AT MIL STN BATHINDA

Amount

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) exc 1.50 sqm each including making good distrubed brick work in cement mortar 1:4 complete all as specified and as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) exc 1.50 sqm but n. exc 4.0 sqm each including making good distrubed brick work in cement mortar 1:4 complete all as specified and as directed.

Demolition of cement concrete (unreinforced) including tiles of any description & terrazo finish, etc. n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of brickwork or stone boulder masonry built in cement mortar including all quoins, arches, pillars etc & remove rubbish from site complete all as specified and as directed .

Taking down Cement plaster including raking out joints hacking for key scrubbing down with water etc, complete all as specified and as directed

Dismantling of asbestos cement corrugated sheet in roof covering complete all as specified and directed.

Dismantling Wall and ceiling boards ( fibre, pulp, nsulation etc) or insulation boards/slabs/blankets any thickness including cover fillets etc complete all as specified & directed.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation over areas, not exceeding 1.5 m deep and getting out in soft/loose soil complete all as specified and as directed.

Excavation over areas, exceeding 1.5 m deep and not exceeding 3.0 m deep and getting out in soft/loose soil complete all as specified and as directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/losse soil complete all as specified and directed.

Excavating in trenches, not exceeding 1.5 m wide and exceeding 1.5 m depth but not exceeding 3.0 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/losse soil complete all as specified and directed.

Returning filling in, approved soft/loose soil, including spreading , levelling, watering and well ramming in layers, each layer not exceeding 25cm in soft/loose soil complete all as specified and directed.

Removing surplus excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Material and Labour for hard core of broken stone or boulders of gauge exceeding 63mm but not exceeding 100mm, deposited, spread, and levelled in layers not exceeding 15cm thick, watered and rolled/rammed to a true surface complete all as specified and as directed.

Material and labour for hard core of broken bricks of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified & directed.

Material and labour for 75 mm thick cement concrete (1:4:8), type D-2 using 40 mm graded stone aggregate as in sub base of floor, under tiles etc. complete all as specified and as directed.

Material and labour for cement concrete (1:4:8), type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete and sub base in floors etc complete all as specified and as directed.

Material and labour for cement concrete (1:2:4), type B-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete and sub base in floors etc complete all as specified and as directed.

Material and labour for RCC M-25 (design mix) using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for RCC M-25 (design mix) using 20 mm graded stone aggregates as in beams, cantilevers, bressummers, lintels over 1.5 m span and the like etc complete all as specified and as directed.(NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for reinforced cement concrete M-25 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like and in chajja etc complete all as specified and as directed. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

M & L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width in type B-1, 1:2:4 (20mm graded stone aggregate) and setting in cement mortar (1:4) complete all as specified and as directed.

Supply and fixing 110 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floors for water drain out purpose as directed 6Kg/Sq cm. complete all as specified and directed

Material and Labour for precast cement concrete (1:2:4) type B1 using 20mm graded stone aggregate in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including necessary formwork and setting in mortar set in cement mortar (1:4) complete all as specified and as directed.

M & L for brickwork with sub class ‘B’ (old size) bricks, straight or curved on plain exc 6 m mean radius built in CM (1:6) complete all as specified and directed.

M & L for brickwork with sub class ‘B’ (old size) bricks (except bricks) straight or curved on plain exc 6 m mean radius built in CM (1:6) complete all as specified and directed.

Material and labour for brick work with fly ash old size bricks straight or curved on plan exc 6.0m mean radius built in cement mortar 1:4 complete all as specified and directed.

Material and labour for brick work with fly ash old size bricks straight or curved on plan exc 6.0m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with fly ash old size bricks, straight or curved on plan to any radius in half brick walls built in CM (1:4), etc; complete all as specified and directed.

Material and labour for 15mm thick rendering in CM (1:4) mixed with water proofing compound as per manufacturer's instructions on external surface of brick work or concrete surfaces and finishing fair and even complete all as specified and directed. Note:- Water proofing compound shall be measured and paid separetely as supply only.)

Supply only liquid water proofing compound complete all as specified and directed.

Supply only water proofing compound complete all as specified and directed.

Material and labour for 15mm thick rendering in CM (1:6) on internal surface fair faces of brick work or concrete surfaces and finishing even & smooth but without using extra cement complete all as specified and directed.

Material and labour for 15mm thick rendering in CM (1:6) on fair faces of brick work or concrete surfaces and finishing even & smooth but without using extra cement complete all as specified and directed.

Material and labour for rendering 5 mm thick in cement mortar in (1:3) on ceiling and finishing the surface even & smooth without using extra cement complete all as specified and directed.

Material and labour for cleaning of new roof wall/ concrete surfaces and applied a coat of cold bituminous primer over cleaned surface @ 0.40 Kg/Sqm followed by APP modified five layer ploymeric membrane 3mm thick, minimum weight 3.6 Kg/Sqm reinforced with polyester non-woven fabric (weighing not less than 150 gms/Sqm) manufactured by M/S STP Ltd/IWL india Ltd or its equivalent, laid as per the manufactures instruction with side over lap of 75mm and end over lap of 100mm and tucked into the chases on vertical surfaces if required and finally finished with bituminous aluminum paint @ 0.10 Kg/Sqm complete all as specified and as directed.

M & L for lime concrete in lime mortar ration 1:3 using 40 mm graded stone aggregate laid to slop/level as directed complete all as specified and directed.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

Supply and fixing Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

Supply and fixing Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

Material and Labour for formwork for rough finish surface of flat sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Material and labour for formwork to soffits of suspended slabs such as roof slab, floor slabs, landings and similar work not exc 200 mm thick (horizontal or sloping) for rough finished surfaces of concrete complete all as specified and as directed.

Material and labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete complete all as specified and as directed.

Material and Labour for formwork to (rough finished surface of concrete) edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs exc 10cm but not exceeding 20cm wide complete all as specified and as directed.

Material and labour for mild steel TMT bars 10mm dia and over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia including making of rungs, handles etc complete all as specified and as directed. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)

All as per item No 46 here in before but 8 mm dia complete all as specified and as directed.

All as per item No 46 here in before but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders etc. complete all as specified and as directed.

S & f MS rungs of 20mm dia bar etc complete all as specified and as directed.

M & L for preparation of new plastered surafaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as per manufacturer instructions and all as specified and directred.

M & L for preparation of old plastered surafaces of walls and applying two coat of oil bound distemper complete all as per manufacturer instructions and all as specified and directred.

Material and labour for applying three coats of white wash on newly plastered or unplastered ceiling surfaces including preperation of surfaces, complete all as specified and directed.

Material and labour three coats of white wash on newly plastered surface of wall including preparation the surface of on walls complete all as specified and directed.

Material and labour for applying two coats of cement base paint over a coat of primer on newly plastered wall surfaces including cornices & pillasters etc as per manufacturer's specifications & instructions including preparation of surface, complete all as specified and as directed.

Material and labour for complete removal of existing treatment and preparing surface for applying two coats of cement base paint over a coat of primer on old plastered wall surfaces including cornices & pillasters etc as per manufacturer's specifications & instructions including preparation of surface complete all as specified and as directed.

Material and labour for 25 mm thick cement concrete (1:2:4), type B-0 using 12.5 mm graded stone aggregate as in floor finished even and fair complete all as specified and as directed.

Material and labour 75mm thick, cement concrete 1:3:6, type C2 using 40mm graded crushed stone aggregate as in floors, plinth protection, paths, sub base etc and finishing top surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for PCC 1:3:6 type C1 (using 20mm graded crushedstone aggregates) as in filling back of pressed steel door frames/chowkhats and for fixing hold fasts, etc. complete all as specified and directed.

S & F pressed steel frames for doors with one or more rebates including hinges, lock strike plate, fixing lugs, etc., size of frame 125 x 60mm, complete all as specified and directed. (thickness of steel sheet shall be 1.25mm)

S & F pressed steel frames for doors with one or more rebates including hinges, lock strike plate, fixing lugs, etc., size of frame 105 x 60mm, complete all as specified (thickness of steel sheet shall be 1.25mm)

Supply and fixing factory made PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, all as specified in Preamble 8B. 3.1 of SSR Part -II (2010) and all as shown on drawing of SSR Part-II (2010) complete all as specified and directed .

Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supplying and fixing in the frame at site all as per instruction and drawing shown for item No 8080 of SSR Part II on Sl Page No 156. complete all as specified and as directed.

S & F for PTMT ( Poly Tetra Methylene Terephthalate ) butt hinges 100mm long best quality complete all as specified and directed.

S & F PTMT ( Poly Tetra Methylene Terephthalate ) barrel tower bolt best quality, 150 mm long complete all as specified and directed.

S & F PTMT ( Poly Tetra Methylene Terephthalate ) door handles, best quality, 150 mm long complete all as specified and directed.

S&F factory made steel windows/ventilators with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded, complete all as specified and directed.

S&F factory made windows/ventilators with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with out glazing bars, complete all as specified and directed.

Supply and fixing mild steel framed work Framed work such as grills, gate, grantings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe290,Gde-E-165 complete all as specified and as directed

S & F 3.0mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S & F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane including hacking out old window glass panes complete all as specified and directed.

S & F MS galvanised mild wire cloth 0.56 mm nominal dia of wire and avarage width of aperture 1.18mm and fixed with tinned tacks to galvanised wire stapple complete all as specified and directed.

Material and Labour for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified and as directed.

Material and Labour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome complete all as specified and directed.

M & L for painting to old steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coat of synthetic enamel paint including preparation of surfaces complete all as specified and directed.

M & L for preparation of new concrete surafaces and applying two coats of synthetic enamel paint over a coat of primer complete all as per specified and directred.

S & F 35 mm thick, 2nd class hardwood, factory made shutters, plain framed panelled shutters (two panels) with with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both side. The size of rail & stiles as per IS :1003 (Part I), kiln seasoned and chemically preassure treated, complete all as specified and directed.

S & F 35 mm thick 2nd class hardwood, factory made shutters, plain framed panelled shutters (any number of panels) with with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both side. The size of rail & stiles as per IS :1003 (Part I), kiln seasoned and chemically preassure treated, complete all as specified and directed.

S&F 2nd class HW 35mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass, gauze, etc.; sizes of members of shutters as specified in SSR Part I Section 8, Clause 8.24 (a) complete all as specified and directed.

Supply and fixing extruded aluminium anodised 100mm long butt hinges type B-21 with galvanised mild steel screws complete all as specified and as directed.

Supply and fixing mild steel barrel tower bolts, 150 mm long, stove enamelled black with bright bolts and fixed (ISI marked) complete all as specified and as directed.

Supply and fixing mild steel sliding door bolts with hasp and staple, length of bolt 250mm, plate type, stove enameled black, with bright bolts not less than 12 mm dia with and including a minimum of 6 bolts and nuts, 4 on bolt plate and 2 on staple plate and fixed, complete all as specified and as directed.

S&F MS pressed handles, oval type stove enamelled black 150 mm long complete all as specified and directed.

S&F MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S & F floor door stopper 150mm size of aluminium alloy body and tounge, anodised, with hard drawn steel spring complete all as specified and directed.

Supply and fixing small fittings of 2nd class hard wood such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and as directed.

M&L for 32mm dia fancy type PVC coated in wooden finish on MS pipe coloured curtain rod with brackets and knobs at both ends with 6 No rings in 1 meter length as per site requirement including taking down old existing PVC conduit pipes with accessories complete all as specified and directed. (Note : The cost of brackets and knobs is deemed to be included in the quoted rate. Nothing extra shall be paid on this account).

S&F aluminium anodised barrel tower bolts of extruded section, 150 mm long of extruded section complete all as specified and as directed .

S&F aluminium anodised handles, 150 mm long, cast type complete all as specified and as directed .

S & F 600x600mmx4mm thick 'E' board as in false ceiling including 'Tee" grid frame work made of special section of MS galvanized sheet 0.30mm thick, bottom portion painted with cellular nitro painting, consisting angle cleats of size 25mm wide, 1.6mm thick with flag fixed to RCC ceiling with dash fastener or wraping the suspending wire around the existing wooden/steel purlin/rafter for suspending grid frame work of size 600mmx600mm suspended with 02 Nos, 1.60mm dia GI wire @ 600mm C/C on main Tee and fixed to T-grid with the help of level clip or as per manufacturer direction. The section consisting of main Tee 37mm x24mmx0.60mm thick, cross runner tee 37mmx24mmx0.60mm and. Perimeter angle 24mmx24mmx0.50mm thick shall be fixed to wall with GI screw of 40mm long @ 450mm C/C along the perimeter of wall including or wall including all as per manufacturer's instruction complete all as specified and directed.

Supply and fixing Vitreous china wash hand basin, white, flat back, fancy type, size 550 x 400 mm including cast iron cantilever bracket 32 mm dia brass waste coupling and including fixing of waste fitting and union including PVC waste pipe of 1mm length complete all as specified and as directed .

S & F vitreous china wash basin, white, flat back, size 580 x 450mm excluding taps, waste, chain and plug and porcelain stopper but including barckets complete all as specified and as directed .

Supply and fixing 15mm bore pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F vitreous china (white) squatting pan 'Orissa' pattern, white, size 580 x 440 mm, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flush pipe, anti-syphonic pipe etc including making good to floor and including trap set, in and including lime concrete complete all as specified and directed.

S&F PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets including 32 mm dia flush pipe of polyethylene of low or high density of PVC complete all as specified and directed.

S & F vitreous china urinal, half stall type, white excluding flushing cistern but including flush pipe, and waste pipeand also including connections to flushing pipe and outpipes, bedding urinal against wall in cement mortar (1:2), securing urinal to plug with and including 60 mm long brass screws, pointing arount urinal back in cement complete all as specified and directed .

S&F vitreous china bowl Urinal, flat back type 465 mm x 355mm x 265mm, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and pointing around urinal back in cement, grating and union for discharge etc. complete all as specified and directed .

S & F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed .

Supply and fixing tubular towel rail brass chromium plated 20 mm dia ‘D’ type 60 cm long including end brackets complete all as specified and as directed.

Supply and fixing three layers 500 litre HDPE water storage tanks polyproof. white in colour rotational moulded polyethylene (cylindrical vertical with closed top) hoisted and fixed in position including Supply and fixing of suitable size inlet/outlet arrangement & other accessories complete all as specified and directed.

Supply and fixing ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of size 20mm bore ( weight 210 gms Minimum) complete all as specified and as directed.

Supply and fixing bib taps, fancy type, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule for 15mm bore dia of pipe complete all as specified and as directed .

Supply and fixing GI tubing medium grade with all fittings and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified and directed .

Supply and fixing GI tubing medium grade with all fittings and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified and directed .

Supply and fixing 15mm bore chromium plated angular stop valve of cast copper alloy, screwed down, high pressure, with on/off handle screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed .

Supply and fixing 15mm bore fancy type chromium platedwith long shank and cup and fixed stop valve of cast copper alloy, screwed down, high pressure, with on/off handle screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed .

Supply and fixing 20mm bore, gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed .

Providing and fixing SFRC (Steel Fibre Reinforced Concrete) Cover and frame (heavy duty HD-20 grade designation) internal size 590x590mm & External size of frame 800x800x100mm including manhole cover having size 590x590x50mm thick and fixed over earthing manhole after demolition of PCC coping & manhole cover & set in CM 1:4 including benching in PCC 1:2:4 and finishing smooth complete all as specified and directed.

S & F PVC connections 15 mm bore, 600 mm length, heavy duty, with PTMT nuts complete all as specified and as directed.

S & F PVC connections 15 mm bore, 450 mm length, heavy duty, with PTMT nuts complete all as specified and as directed.

Supply and fixing in repair stainless steel, Chromium plated, decorative type, soap dish holder of approximate size 100 x 75 x 0.90 mm fixed to wall with Chromium plated brass screwes including plastic gutties complete all as specified and directed .

S&F in repair PVC (SWR) 110mm bore pipes single socketed, ISI marked, in any length with rubber ring joints, fixed to walls with MS clamps complete all as specified and directed.

S & F in repair 110 mm bore, PVC (SWR) fittings such as bends, tee, shoe etc; fixed to PVC pipes, complete all as specified and directed.

S & F PVC waste pipe 32mm bore for WHB/Urinal complete all as specified and directed.

Supply and fixed cast iron nahani trap 75mm dia with CP grating including jointing to waste pipe complete jointed in cement mortar complete all as specified and as directed

S & F cast iron sand soil waste and vent pipe 75mm bore with or without ears fixed with cement joints laid in trenches/floors or fixed in walls complete all as specified and directed.

S & F cast iron sand soil waste and vent pipe 100mm bore with or without ears fixed with cement joints laid in trenches/floors or fixed in walls complete all as specified and directed.

S & F 100mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and directed.

S & F 100mm bore cast iron bends (any radius),diminishing pieces or tapers (larger bore measured) with heel rest including oval access door complete all as specified and directed.

S & F 100mm bore cast iron cowl fixed with cement joint in (1:2) cement mortar complete all as specified and directed.

Supply and fixing 75mm dia of long neck cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate complete all as specified and directed.

S & F CP grating (with or without waste hole), 150 mm size, fixed on gully trap etc complete all as specified and directed.

Material and labour for Salt-glazed stoneware gully traps of size 150x150mm, square or round mouthed, type 'P' complete all as specified and as directed.

Supply and fixing Salt-glazed stoneware drain pipes 150mm bore (internal) of grade 'A' laid in trenches and jointed etc. complete all as specified and directed .

Supply and fixing Salt-glazed stoneware drain pipes 100mm bore (internal) of grade 'A' laid in trenches and jointed etc. complete all as specified and directed .

Material and labour for PCC (1:3:6) type C-2 using 40 mm graded stone aggregates as in concrete bed of (SGSW) drain pipes of 150 mm dia( internal), laid to required slope including packing under and haunching against the sides of pipes after these are laid and tested complete all as specified and as directed . Note :- (i) Thickness of concrete bed below the barrel of pipe shall be 10 cm. (ii) Width of concrete bed shall be equal to outer dia of drain pipes (not of sockets / collar)

Cutting into existing manholes / septic tank for connecting new drains of size 150 mm, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-l smooth finished, and reforming benching as required complete all as specified and as directed

Material and labour for non-skid coloured ceramic tiles 7-8 mm thick (square / rectangular), area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white cement with pigment or coloured cement to match the shade of tiles over and including 15 mm thick screed plaster in CM 1:6 complete all as specified and as directed .

Material and labour for non-skid coloured ceramic tiles 7-8 mm thick (square / rectangular), area of each tiles exceeding 0.08 Sqm but not exceeding 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in white cement with pigment or coloured cement to match the shade of tiles over and including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed .

M & L for Acid resistant tiles 15mm thick vitreous ceramic, unglazed of size as directed by GE, set, jointed and pointed in chemical resistant mortar, resin type, in floors and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed .

Material and Labour for glazed ceramic coloured tiles of approved quality in vertical surfaces 450mmx300 mm x7mm thick set jointed in neat cement slurry/paste and pointed in coloured cement to match with the tiles over and including 10mm thick plaster in CM 1:4 complete all as specified and directed. Note:- Rendering will be done in coarse sand (Toka sand ) only.

Material and labour for machine cut kota stone slab flooring 20-25mm thick over and including 15mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete complete all as specified and directed.

Material and labour for machine cut kota stone slab 20-25mm thick as in riser of steps, skirting, dado and pillar laid over 10mm thick rendering in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Material and labour for cement concrete tiles 25cm x 25cm x 20 to 22 mm thick, with grey cement and no pigment machine pressed; set jointed and pointed in neat cement slurry over and including cement 15mm thick screed in cment mortar 1:6 as in roof and floor tiles complete all as specified and directed

Material and labour for making benching with PCC 1:2:4 type B0 using WPC along side wall adjoining to roof in concave shape complete all as specified and directed .

M&L for 50mm thick cement concrete type B1, 1:2:4 (20mm graded crushed stone aggregate) as in flooring, sub-floors etc and finishing surfaces of concrete topping as even and fair or even and rough to receive the topping layer complete all as specified and directed .

M&L for cement concrete type B1, 1:2:4 (20mm graded crushed stone aggregate) as in bedding, benching of manholes, copings, surface channel roof kerbs or mud stops, rounded or chamfered on edges etc. complete all as specified and directed .

Material and Labour machine pressed precast concrete coloured interlocking paver block any shape, size and pattern, IS - 15658-2006 (Marked) of 60 mm thickness of M-35 grade with grey cement & pigment including 25mm thick sand screed beding etc complete all as specified and directed .

Material and Labour machine pressed precast concrete coloured interlocking paver block any shape, size and pattern, IS - 15658-2006 (Marked) of 60 mm thickness of M-35 grade with grey cement & pigment including 25mm thick sand screed beding etc complete all as specified and directed .

Taking down carefully existing unserviceable copper / aluminum point wiring (light, fan, socket) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, regulators, sockets, light fitting etc and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and directed.

Material and Labour for point wiring with multi stranded copper conductor FRLSH cable, 1100 volts grade PVC insulated and unsheathed of size 1.5 Sqmm single core in and including PVC concealed conduit not less than 20mm dia ( medium quality ISI marked) and conduit fittings and MS sunken box of suitable size covered with and including 3 mm thick bakelite laminated sheet top cover for one fan / light controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly including cutting chasing of wall and making good disturbed surface in CM (1:3) and finishig the surface to match complete all as specified and directed .Note:- ( Switch and socket etc shall be measured and paid separately under approriate items of BOQ).

All as per item No 141 here in before but for socket outlet 5 pin, 6 Amp on same board complete all as specified and directed .

All as per item No 141 here in before but for socket outlet 5 pin, 6 Amp on independent board complete all as specified and directed .

All as per item No 141 here in before but for one socket outlet 6 pin, 15 Amp with cable of 2.5 Sq mm, multi stranded copper conductor FRLSH cable on the independent board including provision of 2.5 Sq mm PVC insulated unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly complete all as specified and directed .

S& F switch piano flush type, 5 Amp 240 Volt, AC one way etc complete all as specified and directed.

S & F XLPE isulated, armored heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 6sq.mm2 core complete all as specified and directed

S&F one socket outlet 5 Pin 5 Amp 230 volts AC complete all as specified and directed. Note:- Switch and socket shall be of same make.

S&F one switch and one socket outlet 5 Pin, 15 Amp 230 volts flush type complete all as specified and directed. Note:- Switch and socket shall be of same make.

Supply and fixing ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed .

Supply and fixing regulator for ceiling fan electronic step type suitable for 1200/1400 ceiling fan complete all as specified and as directed.

Supply and fixing lamp holder angle/straight, polycarbonate body with back plate complete all as specified and as directed.

Supply and fixing 9/10 Watt LED bulb suitable for fixing in lamp holder complete all as specified and as directed.

Supply and fixing single phase, 50 hz, 230 volt exhaust fan of size 300 mm sweep( metal body) energy efficient including making opening in wall for fixing exhaust fan and making good the disturbed surface by applying existing periodical treatment including making connection and providing 3 core copper conductor cable of suitable size complete all as specified and as directed .

Supply and fixing single phase, 50 hz, 230 volt exhaust fan of size 450 mm sweep( metal body) energy efficient including provision of louvre shutter on outer surface of the wall including making opening in wall for fixing exhaust fan and making good the disturbed surface by applying existing periodical treatment including making connection and providing 3 core copper conductor cable of suitable size complete all as specified and as directed .

Supply and fixing wall mounted LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed .

Supply and fixing MCB, SP, 6 to 32 Amps, 'C' curve, 230 Volts, breaking capacity not less than 10 KA with over load and short circuit protection complete all as specified and as directed .

Supply and fixing MCB, DP, 32 to 63 Amps, 'C' curve, 415 Volts, 50 Hz, breaking capacity not less than 10 KA with over load and short circuit protection complete all as specified and as directed .

Supply and fixing MCB, SPN, 32 Amps, 230 Volts, breaking capacity not less than 10 KA with over load and short circuit protection,50 Hz including necessary attachment complete all as specified and as directed .

Supply and fixing sheet metal enclosures double door made out of CRCA mild steel sheet, flush mounted, acrylic door, 8 way, DB SPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc including taking down old complete all as specified and as directed .

Supply and fixing sheet metal enclosures double door made out of CRCA mild steel sheet, flush mounted, acrylic door,4 way, DB SPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc including taking down old complete all as specified and as directed .

Supply and installation automatic hand dryer 230 volts AC wall mounted complete having stainless steel high speed jet hand dryer double wave it should be minium 22000 RPM suitable for high traffic cat No. DAHD0049 of make Dolphy complete all as specified and as directed. equivalant Make:- Zesta/Delacrox/AllExtreme/Bath Guru/Drizle etc.

Supply and installation automatic hand soap dispenser (SOFT GEL) 230 volts AC wall mounted complete having capacity of 1000ml cart part No. DSDR0110 of make Dolphy complete all as specified and as directed. Equivalent make:- Unitech/Prestige/Jaquar Etc.

S & F blanking plate etc complete all as specified and as directed .

Supply and laying or fixing or passing through in and including concealed PVC conduit 20mm dia heavy duty, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed twin core 6 sq. mm nominal cross section in service connections including taking down old unserviceable wire complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground (PCC 1:2:4 B-1 using 20 mm graded stone aggregates for concrete pit including 10 mm thick CI cover frame) depth of pit not less than 2.25 m below normal ground level with top edge of the plate not less than 1.5 m below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal / coal dust and common salt filling in alternate layers and connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts check nuts and washers of GI or steel and connecting to earthing test point, main switch board, testing on completion including GI pipe 20 mm dia light grade for watering and bringing out the watering pipe upto 30 cm above the normal ground level plugged at top including all fitting and GI pipe 15 mm dia light grade for the protection of GI wire from earth pit to earth point, all as specified as shown in electrical plate No 3 SSR Part-I and testing on completion complete all as specified and as directed . Note :- PCC chamber shall be constructed at least 1.5 m away from earth pit pipe for watering shall be provided in slanting manner.

Note:- Net contract sum shall be calculated after deduction of Sch of credit of Rs. 74365.00

SHARDA ENTERPRIES

Easyways Enterprises

Aman Enterprises

M/s Vandana Builders