Construction of 1. Amenity block at North parking, 2. Toilet block at different locations such as near Kedargouri temple, near Taranga club, near Crafts pavilion, drop off facility and 3. Ritual pavilion at Ekamra Kshetra under EKAMRA Conservation

Earthwork in excavation in all types of soil for site leveling, foundation, pits, trenches and other civil works upto and including 1.5metre depth and stacking the soil upto a lead of 100 metre and including dewatering, removing slush, shoring and strutting (as required), complete as per specification and as directed by the Engineer-In-Charge.

Clearing and grubbing roads and land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness.

Filling the Foundation and Plinth, sides of foundation, etc. with excavated materials (excluding rock), in layers not exceeding 0.225 m in depth including cost of watering, ramming, dressing and levelling the top to proper level & gradient, cost of labour, conveyance, loading, unloading, T&P, etc, all complete as per the direction of Engineer-in-Charge.

Providing and applying of Antitermile treatment by drilling 12mm dia holes at adislance of 30cm. @junction of wall and floor about 300mm aprt deep enough to reach the soil below and chemical emulsion (PREMISE, IMIDACHLOPRIED 30.5 SC OF BAYER MAKE mixed with 475 ltr. waler) pumped these holes to soak the soil @ 1 ltr.solution of each hole as per manufactures specification and the holes should be pluged with filling materials including cost of all materials, labour charges, conveyance and all taxes including hiring charges of machinaries as per direction of Engineer-in-charge.

Supplying and filling in foundation and plinth with good quality river sand including watering, ramming with cost, conveyances, royalties of all materials and cost of all labour with T&P required for the work etc. complete as per specification & direction of Engineer-in-charge

Plain cement concrete (1:3:6) using 40mm down size black hard crusher broken granite chips of approved quality from approved quarry including hoisting, lowering and laying concrete in layers, watering, curing etc. complete including cost, conveyance, royalties of all materials with labour,labour cess and T&P etc. required for the work complete as per the direction of the Engineer-in-charge.

Providing, lifting, hoisting and laying Reinforced cement concrete of M-25 grade as per approved designs and drawings having a minimum compressive strength (in work test) 25 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position.

Raft & Column upto Plinth

RCC Wall

PLINTH BEAM

COLUMN

Ground Floor

First Floor

Second Floor

Third Floor

Mumty

LINTEL BAND & SILL BAND

Ground Floor

First Floor

Second Floor

Third Floor

STAIRCASE

Ground Floor

First Floor

Second Floor

ROOF BEAM

Ground Floor

First Floor

Second Floor

Third Floor

Mumty

Ground Floor

First Floor

Second Floor

Third Floor

Mumty

CHAJJA

Supplying Cutting, straightening coiled or bent up M.S. Rod or tor steel of primary steel producers such as SAIL / Tiscon / RINL / JINDAL STEEL (grade Fe-550D) etc. including bending, binding, welding and jointing if necessary and tying the grills and placing in position as required for R.C.C. Work and for providing fan hooks as required, hoisting, lowering, laying including cost, conveyances of M.S. Rod or tor steel and binding wires of 18 to 20 gauge and labour required for the work for bending, binding and tying the grills in all floors with labour cess etc. (payment will be made on standard weight of B.I.S. for M.S. Rods or tor steel only) etc. complete as per specification & direction of Engineer-in-charge.

Ground Floor

First Floor

Second Floor

Third Floor

Mumty

Fly Ash brick masonry in cement mortar (1:6) in foundation & plinth using Fly Ash bricks of 23 x 11 x 8 cm size having a crushing strength of not less than 75 kg./sqcm with dimensional tolerance ± 2% including splays cutting circular moulding chamfering and corbelling and similar such type of works with all necessary projections watering and curing after immersing the bricks in water at least for six hours before use including cost, conveyance, royalties of all materials with all labour,labour cess and T & P required for the work complete in all respect as per direction of Engineer-in-Charge.

Fly Ash brick masonry in cement mortar (1:4) in super structure using Fly Ash bricks of 23 x 11 x 8 cm size having a crushing strength of not less than 75 kg./sqcm with dimensional tolerance ± 2% including splays cutting circular moulding chamfering and corbelling and similar such type of works with all necessary projections watering and curing after immersing the bricks in water at least for six hours before use including cost, conveyance, royalties of all materials with all labour,labour cess and T & P required for the work complete in all respect as per direction of Engineer-in-Charge.

Ground Floor

First Floor

Second Floor

Third Floor

Providing 12 mm thick cement plaster with cement mortar of mix (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties of all materials with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge

Ground Floor

First Floor

Second Floor

Third Floor

Providing 16 mm thick cement plaster with cement mortar of mix (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties of all materials with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge

Ground Floor

First Floor

Second Floor

Third Floor

Providing 6 mm thick cement plaster with cement mortar of mix (1:4) with screened and washed sharp sand for mortar and finished smooth to R.C.C. work after closed deep chipping & slurry treatment including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties of all materials with cost of all labour, T&P, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge

Ground Floor

First Floor

Second Floor

Third Floor

Third Floor

Providing Vitrified tile flooring using vitrified tiles conforming to IS 13755 of 600x600 (homogeneous) of premium quality (JOHNSON / SOMANY/ KAJARIA/ RAK) in floors, treads on steps and landings on 20mm thick bed of cement mortar of mix (1:4) laid in proper slope and gradient with screened and washed sharp sand for mortar and fixing with neat white cement slurry,grouting the joints with neat white cement slurry mixed with required quantities of pigments of approved make to match the shades of the vitrified tile if required , watering and curing for 21 days, including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour,Labour cess , sundries, T&P required for the work, complete in all respect as per specification and direction of Engineer-in-charge

Ground Floor

First Floor

Second Floor

Providing and laying Vitrified skirting tiles 600x600 mm (thickness to be specified by the manufacturer) 1st quality conforming to IS: 13755 of (JOHNSON / SOMANY/ KAJARIA/ RAK) or equivalent approved make, colours & shades, laid on 12 mm thick cement mortar 1:3 (1cement: 4coarse sand ) including pointing the joints with white cement and matching pigments, etc. complete as per direction of EIC at all floors and all heights

Ground Floor

First Floor

Second Floor

Providing and fixing 20mm thick Granite stone flooring (sample of Granite stone should be approved by EIC) for stair case trade, riser and similar locations where ever required in horizontal/vertical surfaces of required size of approved shade, colour and texture, with moulding edge etc. laid over 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) with joints treated with white cement mixed with matching pigment, epoxy touch ups including rubbing, curing, moulding and polishing to give high gloss finish etc. complete as per direction of Engineer-in-charge. In all floors and all heights.

Ground Floor

First Floor

Second Floor

Providing and fixing 20mm thick Granite stone flooring (sample of Granite stone should be approved by EIC) for stair case trade, riser and similar locations where ever required in horizontal/vertical surfaces of required size of approved shade, colour and texture, with moulding edge etc. laid over 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) with joints treated with white cement mixed with matching pigment, epoxy touch ups including rubbing, curing, moulding and polishing to give high gloss finish etc. complete as per direction of Engineer-in-charge. In all floors and all heights.

Ground Floor

First Floor

Second Floor

Priming one coat with wall cement primer (water bound) to make an even finished surface in all floors and heights to wall surface of approved make and shade including sand papering, applying putty wherever necessary & cost of scaffolding, staging charges with cost, conveyance, cost of all labour,labour cess T&P etc. complete as per the direction of the Engineer-in-charge. (Make: Asian/ Berger or equivalent make duly approved by Engineer-in-Charge)

Ground Floor

First Floor

Second Floor

Third Floor

Mumty

Priming one coat with wall cement primer (water bound) to make an even finished surface in all floors and heights to wall surface of approved make and shade including sand papering, applying putty wherever necessary & cost of scaffolding, staging charges with cost, conveyance, cost of all labour,labour cess T&P etc. complete as per the direction of the Engineer-in-charge. (Make: Asian/ Berger or equivalent make duly approved by Engineer-in-Charge)

Ground Floor

First Floor

Second Floor

Third Floor

Painting two coats with plastic emulsion paint over a coat of water bond cement primer to make an even finished surface in all floors and heights to wall surface of approved make and shade including sand papering, applying putty wherever necessary & cost of scaffolding, staging charges with cost, conveyance, cost of all labour,labour cess, T&P etc. complete as per the direction of the Engineer-in-charge. (Make: Asian/ Berger or equivalent make duly approved by Engineer-in-Charge).

Ground Floor

First Floor

Second Floor

Third Floor

Mumty

Painting two coats with approved antifungal weather seal paints (ISI) of approved colour, shade on wall surface over a coat of wall primer(ISI) water bound including sand papering, polishing the surface, cost, conveyances, taxes of all materials and cost of all labour,labour cess with T&P etc, complete as per specification & direction of Engineer-in-charge. (Make: Asian/ Berger or equivalent make duly approved by Engineer-in-Charge)

Ground Floor

First Floor

Second Floor

Third Floor

Supplying, fitting and fixing of stainless steel of 304 grade in hand railing using 50 mm dia of 2 mm thick circular pipe with Balustrade of size 32 mm x 32mm x 2mm @ 0.90 mtr C/C and stainless aquare pipe bracing of size case as per approved design and specification, buffing, polishing etc. with the cost, conveyance taxses of all material, cost in all floor of all labour etc. complete in all respect and as per direction of Engineer in charge in all floor.

Providing and fixing seasoned sal wood work in frames at any locations including doors, windows, cupboard, clerestory and other frames fixing in position including cost of hinges, M.S. flat (30mm x 6mm) hold fasts lugs or dash fasteners of required dia and length as per drawing / specification, at all floors and all heights.

Priming one coat with any approved wood primmer including cost of primmer & labour to give an even shade excluding cost of primer in all floor.

Painting Two coats with approved Wood Shine Paint of approved colour, shade over a coat of primer including sand papering, polishing the surface, cost, conveyances of all materials and cost of all labour etc, complete as per specification & direction of Engineer-in-charge

Providing and fixing ISI marked 35 mm thick flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak three ply veneering with vertical grains or cross bands and face veneers on both faces of shutters of approved design including cost of all door fittings and fixtures etc. complete and as per direction of Engineer in charge

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. Frame size 65 x 125 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. 30 mm thick

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Providing Decorative small eye Laterite stone masonry in Super structure with cement mortar (1:4) using machine cut laterite stone of approved quality from approved quarry including cost of all material, all taxes and cost of all labour, conveyance, loading & unloading, royalties, hoisting, lowering, sundries, T&P required for the work etc. complete in all respect as directed by the Engineer-in-Charge.

Providing & laying of 80mm thick factory made cement concrete interlocking paver block of M35 grade and approved make variety colour and size made by Block making machin with strong vibratory compaction of approved design and shape, laid in required colour and pattern over 50mmthick compacted bed of coarse sand ,filling the joints with fine sand etc.all compelte including cost,conveyance,royalty,taxes of all materials,labour,T & P etc.Complete and as per direction of Engineer in charge.

Supplying and fixing of Pre cast kerb stone of size 300mm x 300mm x 150mm of M-30 grade of approved make, design, colourand size made by Block making machine with proper compaction fixed in required pattern etc. complete in all respect conforming to IS 5758: 1984 and as per direction of Engineer in charge.

Providing and fixing stainless steel ( Grade 304) of SHS/RHS, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.

Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Conforming to IS: 3548 & IS: 16231(FENESTA/NCL VEKA LTD)

Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. 6mm thick Black glass panes & Fly proof Mesh. Glass: Saint Gobain, AIS

Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.

Using R4 series with frame (64mm & above) x (45mm & above) & sash (44mm & above) x (85mm & above). ).Including 12 mm Toughened Glass.(FENESTA/NCL VEKA LTD)

Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Conforming to IS: 3548 & IS: 16231(FENESTA/NCL VEKA LTD)

Using R1 series with frame (33mm & above ) x (35mm & above).

Providing and laying grading conc. 25 mm (avg. thickness) cement concrete of required slope of mix 1:2:2 (1cement:2sand:2 graded stone aggregate of 10 mm nominal size) mixed with approved water proof compound as per manufacturer's specification on top of slab including cement slurry, all complete, including the cost of water proofing admixture, which should be approved by the Engineer-In-Charge.

Toilet Block & Amenity block First Floor

Amenity block Third Floor

Amenity block Mumty

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

For vertical surface two coats @ 0.70 kg per sqm per coat

For horizontal surface one coat @1.10 kg per sqm.

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete :

Serrated with central bulb (225 mm wide, 8-11 mm thick)

Supply & Installation of LED base Glow Sign Board as per below specification (in both English & Odiya Letters) Total board size:19 × 3 ft (Odiya) & 22 × 3 ft (English) ACP Sheet:Aluminium based cover panel sheet (ACP) for letter fixing on the sign board (Silver Metallic colour).Aluminium:2.5" × 1.5" hollow square pipe framed cover with aluminium based cover panel sheet. Plastics Sheet:3 mm plastic sheet (White in colour) in Odiya & English letters.L.E.D:0.3 to 1.5 Watts (White colour)Power Supply:SMPS (Switched Mode Power Supply), RPS (Regulated Power Supply)Input Voltage: 160 to 230 A.C.Output Voltage: 12/24 Volts D.C.Silicon Paste:Paste for ACP sheet.M.S. Angles:S/F of M.S. angle with setting, bending & welding work for structural work.Size of M.S. angle:40 × 40 × 4 mm,30 × 30 × 5 mm,25 × 25 × 5 mm.For supporting of LED sign board, G.I. nut bolt, painting in black complete and as per direction of Engineer in charge.

Manufacturing, Providing and installing of GFRC (Glass Fiber Reinforced Concrete) Screens in pattern, design and colour of approved make to be fixed in between RCC/Brick work column or structural work with dry fixing method with appropriate framework, using fasteners and necessary hardware etc. in building façade.It shall be made from 53 grades white Portland cement, quartz fine silica sand, alkali resistant glass fibre, super plasticizers and UV resistant synthetic inorganic pigments.The rate includes the cost of 25 mm thick GFRC element, frame and anchor fasteners, labour charges for fixing, required scaffolding, working at all levels/heights and leads, including all costs of material, labour, etc. Complete and as per direction of Engineer in charge.

Providing and fixing modified clay material – MCM CusStone-1200 × 600 mm, thickness 2.5 mm to 3 mm PHOMI make, as per company standard dimension, pattern, colour as specified, manufactured through infrared patented complete and as per direction of Engineer in charge.

Stone work (machine cut edges) for wall lining etc. (veneer work) , backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade complete and as per direction of Engineer in charge.

Laterite Stone 75 mm thick- Exposed face machine cut and table rubbed with rough backing.

Laterite Stone Masonry incement mortar (1:6) in foundation and plinth. Including cost conveyance royalty of all materials, labour T&P required for the work etc. complete as per direction of the Engineer- in-charge

Providing and laying 150 mm thick khandolite flat block packing in flooring in required design and patterns, in linear as well as curvilinear portions all complete as per drawings over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete (excluding khondalite) as specified and as directed by the Engineering-Charge.

Loosening,levelling and compacting original ground supporting embankement to faciliate placement of first layer of embankement,scarified to a depth of 150 mm,mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in table 300-2 for embankment construction & clause-305 of MOSRT&H Specifications for Road & Bridge works(5th. Revision)

Providing and laying Granular Sub-base with Grading-VI stone screening materials as per Table 400-1 as per approved drawing and technical specifications complete in all respect as per Section 900 and Clause 401 of MoRT&H Specifications for Road & Bridge works (5th Revision) & including cost & conveyance of all materials, labour, T&P, royalty etc complete and as per direction of Engineer-in-Charge.

Khandolitc stone Masonry work in Super Structure in cement mortar (1:4) (1 Cement : 4 Course Sand) including cost of all materials, labour T &P etc required for the work all complete as per direction of Enginecr-inCharge).

Khandolite Stone cladding of 75 mm thick on exposed face and edge machine cut and table rubbed with rough backing for wall lining etc.12mm thick cement plaster (1:3) jointed with neat cement slurry mixed with pigments to match the shade of the tiles including rubbing, polishing etc. complete (excluding cost of khondalite) as per specification and direction of Engineer in Charge.

Khandolite Stone Ornamental cladding of 75 mm thick on exposed face and edge machine cut and table rubbed with rough backing for wall lining etc.12mm thick cement plaster (1:3) jointed with neat cement slurry mixed with pigments to match the shade of the tiles including rubbing, polishing etc. complete (excluding cost of khondalite) as per specification and direction of Engineer in Charge.

Providing and fixing cast iron railing plus alloys as per approved design including preparation of design pattern, casting, shot blasting, polishing the casting, painting with two coats of poly urethane coating of approved RAL number over one coat of zine chromate primer, ransportation to site, welding of cast Iron railing using MIG welding at site, erection at site with neessary core cutting and non-shrink grouting with GP2 and making final touch up with paint wherever required all complete as per the direction of Engineer-in-charge.

Supplying and laying precast U drain of internal size (1000x1000) WITH LID COVER: following details as per direction of Engineer in charge Internal dimensions: 1000 X 1000 X 2000 MM Grade of concrete: M 50 Fe 500 CRS steel Load carrying capacity: 5T Wheel Load (T25) Raft thickness (e) = 110 mm Wall thickness at top (c) = 85 mm Wall thickness at bottom (d) = 110 mm

Directional Free Standing Signage (Specification to be followed from Cl. 4.1 of BDA guideline Notification No. 15689 dtd. 22.09.2020 for heritage signage): The signage structure is a combination of wrought/cast iron pipe structure with sandstone base and caping. Stainless Steel Panel flags (minimum 4 nos of panel printed both sides) with symbol and text digitally H1625-RS printed on micro prismatic retro reflective boards conforming to type XI DG3 (diamond grade) 4000 series. Total height : 4000 mm Text language: Odia and English. Text height: Odia 80-85 mm; English 75-80 mm, Icon height 200-220 mm as per drawings & direction of Engineer in Charge.

Directional Wall mounted Signage (Specification to be followed from Cl. 4.2 of BDA guideline Notification No. 15689 dtd. 22.09.2020 for heritage signage): Mild steel panels (with/without wrought iron frame) screwed directly on wall. Text printed digitally H1625-RS printed on micro prismatic retro reflective boards (bothside) conforming to type XI DG3 (diamond grade) 4000 series. Text language: Odia and English. Text height: Odia 70-75 mm English 65-70 mm . Icon height: 150-170 mm as per drawings & direction of Engineer in charge.

Wayfinding signage(Specification to be followed from Cl. 4.3 of BDA guideline Notification No. 15689 dtd. 22.09.2020 for heritage signage): Mild steel panels (with/without wrought iron frame) screwed directly on wall. Text printed digitally H1625 -RS printed on micro prismatic retro reflective boards conforming to type XI DG3 (diamond grade) 4000 series. Text language: Odia and English. Text height: Odia 40-45 mm English 40 - 45 mm Century 30 -35 mm. Icon height: 155 -175 mm as per drawings & direction of Engineer in charge.

Location signage (Specification to be followed from Cl. 4.4 of BDA guideline Notification No. 15689 dtd. 22.09.2020 for heritage signage): The signage structure is a combination of wrought/cast iron pipe structure with sandstone base and iron brackets. Stainless Steel Panel flags with symbol and text digitally H1625-RS printed on micro prismatic retro reflective boards conforming to type XI DG3 (diamond grade) 4000 series. Text language: Odia and English. Text height: Odia 55-60 mm; English 55-60 mm as per drawings & direction of Engineer in Charge.

Facility Signage(Specification to be followed from Cl. 4.8 of BDA guideline Notification No. 15689 dtd. 22.09.2020 for heritage signage): Digitally H1625-RS printed on micro prismatic retro reflective boards conforming to type XI DG3 (diamond grade) 4000 series, Panel size: 450 mm x 450 mm, Icon height: 150-250 mm, Text height: 60-65 mm, In order to give direction to a particular facility, the direction arrow should be added below the icon along with information on walking distance etc. complete as per drawing and direction of Engineer in charge.

Supplying and fixing of 1 set (4 Nos. of 120 Litre of different colour Plastic Wheel Dustbin, WB120L) chain linked connection with each other and standing on pedestal including foundation, labour, transportation, installation, tnp etc. complete

HORTICULTURE

Supplying and stacking of good earth at site including royalty and carriage up to 5 km as per specification and direction of Engineer-in-Charge.

Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 05 k.m. lead complete (Cattle manure measured in stacks will reduced by 8% for Payment).(2:1)

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) .

Screened through sieve of I.S designation 20 mm

Screened through sieve of I.S designation 16 mm

Screened through sieve of I.S designation 4.75 mm

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Amenity ,Boundary,Hardscape & Allied Works

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge(2:1)

Providing and stacking of Ipomoea purpurea (Morning glory) of height 30 cm to 45 cm. in 20 cm size of Earthen pot/ Plastic pot as per direction of the officer-in-charge

Amenity ,Boundary,Hardscape & Allied Works

Providing and stacking of Jasmine humile (Yellow) of height 30 cm to 45 cm. in 20 cm size of Earthen pot / Plastic pot as per direction of the officer-in-charge.

Providing and stacking Duranta Golden, having ht.12 cm to 15 cm bushy shape with fresh and healthy leaves in Poly Bag and as per direction of the officer-in-charge

Providing, stacking and Displaying Syzygium myritifolium (Eugenia oleina) having 45 cm to 60 cm height, well developed with fresh, healthy & shining foliage in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing, stacking and Displaying Ixora singaporensis different colour having 30 cm and above ht., well developed with fresh & healthy foliage with bloom in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and stacking of Tabernaemontana divaricata (Chandni double) of height 90-105 cm. in bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Jasmine grandiflorum (chameli) of height 30 cm to 45 cm in 20 cm size of Earthen pot / Plastic pot as per direction of the officer-in-charge.

Providing and stacking Tradescantia zebrina having in 15 cm size of Earthen Pot / Plastic Pot and as per direction of the officer-in-charge.

Providing, stacking and Displaying Canna dwarf of height 25 to 30 cm., 2 to 3 suckers in 20 c.m Earthen Pot / Plastic Pot and as per direction of the officer-in-charge.

Providing,stacking and Displaying Adenium Obesum grafted well developed with fresh and healthy 4 to 5 barnch 60 cm to 75 cm ht. plant in 40 cm size Challi / Plastic Pot and as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 90-105 cm. bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Ficus benjamina (green) of height 150-165 cm.bushy with helathy branches and lush green foliage in big sizeHDPE bag as per direction of the officer-in-charge.

Providing, stacking and Displaying Acalypha twisted well developed with fresh & healthy 30 cm & above ht. plant in 20 cm size Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge

Providing, stacking and Displaying Dracaena Fragrans”Massangeana’’ having ht. 30 cm & above with full of leaves, well developed, fresh and healthy in 25 cm size of Earthen pot / Plastic pot and as per direction of the officer-in-charge.

Providing and stacking of Plumeria alba dwarf of height 90-105 cm. with 3-4 branches and thick stem in big size HDPE bag as per direction of the officer-in- charge.

ELECTRICAL ITEMS FITTINGS & FIXTURES

Supply, installation, testing and commissioning of BIS certified surface mounted exterior-rated LED linear Wall washer luminaire (1000-1200)mm with housing color designed for wall washing and grazing architectural lighting applications having extruded aluminum housing with die-cast aluminum end-caps with supply of 150W 24V IP67 Driver as per design requirement and approval drawings.

Supply, installation, testing and commissioning of 4 Mtr Height grooved mild Steel tube with cast iron embblellisments decorative pole (equivalent to Homdec Make -HL-ND-ILBP2790)fitted with Cast Aluminium Lighting Fixtures with Arcylic diffuser, Stainless Steel difuser strips, Coating system sanding & shot blasting Pre-Teatment, Epoxy Primer, Top Coating in U V Ray Resisatant / Polyster COating PCD 175, Including Diffuser lamp LED Wattage - 36 W. with coil earthing and Junction box for cable termination (loop in loop out) including foundation as per design requirement and approval drawings.

Supply, installation, testing and commissioning of 3.5 Mtr Height heavy GI pole of 65 mm dia with MS base plate of 250 X250 X12 mm thick, 16 mm dia 550 mm long foundation bolts, with supply of Sintex distribution box with 6 Amp MCB, Channel, Back cover with screws including supply of cast aluminium lighting fixture with acrylic diffuser, stainless steel, difuser strip, coating system sanding and shot blasting, pre treatment, epoxy primer, top coat in UV ResistantP.U/Polyster coating suitable for retrofit LED lamp equivalent to Catlogue No. HL-ND-ILPB2790, LED Wattage 30 Watt (Retrofit LED Lamp) with coil earthing and Junction box for cable termination (loop in loop out) as per design requirement and approval drawings.

Supply, installation, testing and commissioning of 6 Mtr Height grooved mild Steel tube with cast iron embblellisments decorative pole fitted ( Homdec-HL-ND-ILBP2750) with Cast Aluminium Lighting Fixtures with Arcylic diffuser, Stainless Steel difuser strips, Coating system sanding & sho blasting Pre-Teatment, Epoxy Primer, Top Coating in U Ray Resisatant / Polyster Coating PCD 175, Including Diffuser lamp LED Wattage - 2*30 W. with coil earthing and Junction box for cable termination (loop in loop out) including foundation as per design requirement and approval drawings.

Supply, installation, testing and commissioning of LED (8-10)w Spike Light Fixture with Body made of PDC Aluminium housing and Toughened Glass Front Cover with Secondary PMMA Diffuser for Optimum Light Distribution. System Efficacy >80lpw.Ingress Protection of IP66 as per design requirement and approval drawings.

Supply, installation, testing and commissioning Of Post top Light Cast Aluminium Lighting Fixtures, SS Glass Strips, Stainless Steel Screws, Corrosion and UV Ray Resistant Coating, Acrylic Diffuser. LED Wattage-24 Wt HL-2750(2) including foundation as per design requirement and approval drawings.

Supply, installation, testing and commissioning of 975 mm High Bollard, Cast Aluminium lighting fixture, Stainless steel screws, Acrylic / Polycarbonate Diffuser, Corrosion & U.V RAY Resistant coating. LED Wattage - 14 Wt HL-2804 including foundation as per design requirement and approval drawings.

(i) Supply, installation, testing and commissioning of Outdoor Architectural IP67 LED Neon Flex Strip. Luminaire should be flexible 24V DC LED Strip based luminaire with Spotless & Uniform diffused illumination. System wattage should not exceed 10W/Mtr. with System efficacy not less than 60LPW. (±5%) (ii) supply of 150 W 24V IP67 Driver as per design requirement and approval drawings. (iii) supply of Aluminium profile with adjustable mounting bracket for Neon 1615 - 1 meter As per design requirement and approval drawings.

FEEDER PILLARS

L T CABLE SYSTEM

Supply of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at Surface, in Existing Pipes, Loose in Trench, Direct Buried in Ground in a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. (MAKE: KEI/HAVELLS/POLYCAB/GLOSTER)

: 10 sq mm 4 core PVC Armoured cables ISI marked

: 16 sq mm 4 core PVC Armoured cables ISI marked

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm (Inside the 63mm dia HDPE Pipe)

Supplying and making end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed / XLPE aluminum cable of 1.1 KV as required.

4 x 16 sq.mm

4 x 10 sq.mm

PIPES

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 100 mm dia

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

63 mm dia

EARTHING SYSTEM

Supplying and laying 6 SWG G.I. wire at 0.50 Meter below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Earthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

LIGHTENNG PROTECTION for Market building complex

Supply of Australian make PP-Stormking ESE-60 Early Streamer Emission type Advanced ESE terminal. It should be made up of SS 316L material and works on dual trust design. ESE terminal should comprised of separate electrically isolated dual SS 316L panels surrounding an SS Central Finial. ESE terminal should anticipate advanced triggering of min. 60 µs. ESE terminal central finial should be made from solid SS rod and its length should be min. 85mm above surrounding panels. ESE terminal SS 316L is low carbon steel which exhibit better corrosion resistance and are stronger at elevated temperatures performance. For isolation of terminal Delrin Adapter should be provided at bottom of terminal which should give higher dielectric strength. ESE terminal should be tested in European accredited test laboratory after 2011 as per revised NFC 17-102:2011 standard. Terminal should be tested for impulse current withstand test in CPRI for 40 kA. Terminal should be non electronic and does not require any external power supply. Model: ESE-60 SS terminal.

Supporting Mast SS: The mounting pole used to support the lightning air terminal shall either be a supporting mast or Free standing mast at a ideal height of 5 mtr. above to be area protected or as per required level of protection. If any height restrictions are there then min height should be 2 mtr but radius of protection will change according to height. The mounting pole and supports shall be securely fixed with brackets and guy wires where required to withstand maximum locally recorded wind velocity. Mounting Pole shall be non corrosive and made up of medium class SS pipe of 2" dia having base plate at bottom for securely fixing mast on rooftop. Also PVC insulated metallic wire rope should be used for guying purpose. The down conductor shall pass through the centre of the pole for the entire length of the pole and it will be out at bottom of the pole. All the mounting accessories should be non-corrosive and made up of SS. Model: Supporting Guyed Mast: 5 mtr. x 2" dia with base plate, guying kit and mounting accessories

Supply of 70sq.mm cross section down conductor of single core flexible Copper cable made of min.990Nos copper strands of 3mm dia and having PVC insulation of min. 3mm thickness and overall dia of 16mm. It should be fixed using SS/GI saddles & fixtures every 0.5mtr. Model: Single core flexible Cu. Cable 70Sq.mm with SS saddles.

MODEL-MES CBR -17.2X3

Supply of 250Micron Copper Bonded Earth Rod 3Mtr long ×17.2 mm dia. CPRI Certified made up of high tensile low carbon steel with copper bonding of 99.9% electrolytic copper. Electrode should be tested in CPRI for 25KA short circuit current. Both the ends of electrode should be threaded and suitable for threaded Ground Rod Clamp .Ground rod clamp should be made up of brass. (MES-GFC ground Filling compound will be provided in 25 kgs Bags.)

Lightning Strike Recorder (L.S.R.): Supply of Australian make L.S.R. It should be non electronic& non- resettable type having 7 digits display &enclosed in an IP-67 enclosure with minimum sensitivity of 1000A & maximum capacity of 220KA tested on 8/20 micro second wave from as per IEC 60-1: 1989. It should be non electronic type and does not require external power supply for working. Supplier should do on site testing of LSR, where impulse generate should be used to show working of LSR. After impulse current passing through LSR it should change the counter reading. Model: LSR.

Supply and installation of UPVC Earthling Chamber with cover and pouring of chemicals with earthing pipes into the hole of recommended size as per IE rule and directionof Engineer in charge.

Installation charges Installation cost of total lightning protection system * Mounting Lightning terminal on the Mast. * Fixing the Mast on the top of roof. * Lying the down conductor from the terminal to earth point. * Clipping of cable in the building wall. * Making 2 Nos. of 10 ft. earth installation. * Pouring of Chemicals with Earthing pipe into the hole. * Lying of cable to connect the earth pit.

WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor sIngle core cable in surface /recessed PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group A

Group B

Group C

Subsequent point of group control

CIRCUIT & SUB-MAIN CABLE

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.

2X1.5Sq.mm + 1 X1.5 Sqmm. earth wire

2X2.5Sq.mm + 1 X2.5 Sqmm. earth wire

2X4Sq.mm + 1 X4 Sqmm. earth wire

4X10Sq.mm + 2 X6 Sqmm. earth wire

4X4Sq.mm + 2 X4 Sqmm. earth wire

Supplying and fixing following modular switch / socket on existing modular plate and switch box including connections but excluding modular plate etc as required.

5A/6A SWITCH

15/16A switch

3pin 5/6A socket

6pin 15/16A socket

Supplying and fixing following size/ modules, GI box along with modular base and cover plate for modular switches in recess etc as required.

2 Module

3 Module

4 Module

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note: Vertical type MCB TPDB is normally used where 3 phase outlets are required.

4 way (4 + 12), Double door

Supplying and fixing following rating, four pole, 415 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required

40A TPN (mcb)

Supplying and fixing 5A to 32A RATING ,240/415V ,10KA,"C" CURVE,MCB suitable for inductive load of following poles in the existing MCB DB complete with- connections,testing and commissioning etc. as required.

Single pole (16A)

single pole (10A)

Supply, installation, testing & commissioning of wall mounting front operated front access extensible type cubicle panel totally enclosed, dust and vermin proof with IP-42/55 protection with hinged and lockabale doors. CRCA sheets including interconnections, tinned copper crimping lugs, bonding to earth and painting suitable for use at 415 V. 3phase 4 wire 50 Hz system, and to withstand a fault level of 35 KA symmetrical for 1 sec at 415 V complete as per specifications, as required and as below: All switchboards shall have provision for entry of cables from the bottom as required. All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The bus bars shall be insulated with heat shrinkable sleeves.SMC/DMC shrouds and busbar supports shall be used with Indication lamp, C.T, Digital Voltmeter, Digital Ammeter and control fuse etc. complete. (Panel)

100A MCCB (incoming 4 Pole)

40A TPN (outgoing)

Multifunction Meter

Rotary operated handle

Spreader link

Space for enegy meter 3 phase .. As per TPCODL aprroval

Supply of Panel ,transportation, Installation

Supply, installation, testing & commissioning of floor mounting front operated front access extensible type cubicle panel totally enclosed, dust and vermin proof with IP-42 /55 protection with hinged and lockabale doors.CRCA sheets including interconnections,tinned copper crimping lugs, bonding to earth and painting suitable for use at 415 V. 3phase 4 wire 50 Hz system, and to withstand a fault level of 35 KA symmetrical for 1 sec at 415 V complete as per specifications, as required and as below: All switchboards shall have provision for entry of cables from the bottom as required. All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The bus bars shall be insulated with heat shrinkable sleeves.SMC/DMC shrouds and busbar supports shall be used with Indication lamp, C.T, Digital Voltmeter, Digital Ammeter and control fuse etc. complete.(Panel)

A. Main Distribution Panel-1nos

ATS 250 A 4 P (Incomer)

125 TPN MCCB (Outgoing)

40A TPN MCB (Outgoing)

32A TPN MCB (Outgoing)

63A TPN MCB (Outgoing)

Indicator R,Y B RGA

ON/OFF Trip indication microswitch with lamp

Digital multifunction meter,CL-1

250/5A Metering CT

Spreader Link

Rotary Operating Handle

Aux cum Trip Alarm

Providing and fixing HT danger notice plate of (250 mm X 200 mm.) made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides and with inscuption in single red colour on front side as required.

Al. EC Busbar (25mm×06mm) 4 nos (R,Y,B,&N)

Space for 3phase energy meter as per TPCODL approved

Panel board with all accessories complete with factory wiring

B.Sub Distribution panel (GROUND FLOOR) -01nos

125A,36KA(Incomer) MCCB

32A TPN MCB (Outgoing)

63A TPN MCB (Outgoing)

16A SPN (Outgoing)

Indicator R,Y B RGA

3-phase class 0.5 Digital Voltmeter

Al. EC Busbars (25mm×06mm)

Panel board with all accessories.

C.Sub Distribution Panel (1ST & 2ND FLOOR ) -02nos

125A,36KA MCCB (Incomer)

63A T&PN MCB (Outgoing)

16A SPN (Outgoing)

32A TPN MCB (Outgoing)

Indicator R,Y B RGA

3-phase class 0.5 Digital Voltmeter

Al. EC Busbars (25mm×06mm)

Panel board with all accessories.

10A SPN (Outgoing) only for 2nd floor for terrace light

DISTRIBUTION BOX

GROUND FLOOR ( TOILET LEFT SIDE & COUNTER )

63A TPN MCB (INCOMER)

10A SP MCB

16A SP MCB

GROUND FLOOR ( TOILET RIGHT SIDE & COUNTER)

63A TPN MCB (INCOMER)

10A SP MCB

16A SP MCB

KITCHEN

63A TPN RCCB

16A SP MCB

10A SP MCB

CAFETERIA

63A TPN MCB (INCOMER)

16A SP MCB

25A SPN MCB

10A SP MCB

1ST FLOOR (TOILET LEFT SIDE)

10A SP MCB

25A SPN MCB (INCOMER)

16A SP MCB

1ST FLOOR (TOILET RIGHT SIDE)

10A SP MCB

25A SPN MCB (INCOMER)

16A SP MCB

1ST FLOOR DORMITORY -1

63A RCCB TPN (INCOMER)

16A SP MCB

10A SP MCB

1ST FLOOR DORMITORY -2

63A RCCB TPN (INCOMER)

16A SP MCB

10A SP MCB

2nd FLOOR (TOILET LEFT SIDE)

10A SP MCB

25A SPN MCB (INCOMER)

16A SP MCB

2nd FLOOR (TOILET RIGHT SIDE)

10A SP MCB

25A SPN MCB (INCOMER)

16A SP MCB

2nd FLOOR DORMITORY -1

63A RCCB TPN (INCOMER)

16A SP MCB

10A SP MCB

2nd FLOOR DORMITORY -2

63A RCCB TPN (INCOMER)

16A SP MCB

10A SP MCB

Supplying and fixing following way, horizontal type three pole andneutral, sheet steel, MCB distribution board, 415 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar, dinbar, interconnections, powder painted including earthing etc. asrequired. (But without MCB/RCCB/Isolator)

4 way (4 + 12), Double door

6 way (4 + 18), Double door

8 way (4 + 24), Double door

FITTING AND FIXTURE

Brush Less Direct Current (BLDC) Fan without RemoteSupply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers,temperature rise=75 °C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and

Modualr Steped type fan regulator

Exhaust fan (225mm Aeroclean plus LD GBD)

LED Batten light (System lumen efficacy ≥105 <120 lm/Watt) Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS: 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection THD <10%, P. F.20.95, IP20, CRI >80, Flicker free, (flicker should be below 5%), life time (LED, Driver & electrical circuitary), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K/4000°K /5700°K/6000K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/Embossing/Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC nsulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy 2105 <120 Im/Watt output. LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm)

LED Batten light (System lumen efficacy ≥120 <135 lm/Watt)Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P. F.≥0.95, IP20, CRI ≥80, Flicker free (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).Powder coated die cast /Extruded aluminium Body (Thickness ≥

LED Down lighter (COB Type) (System lumen efficacy ≥ 105 < 120 lm/Watt) Supplying, installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/square/ Rectangular) COB Type of following body material and construction as per IS: 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P. F.≥0.95, IP20, CRI>80, UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitary), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K/5700°K/6000°K/6500°K (As per ANSI Bin), SDCM

Mirrior Light

LED Flood Light, powder coated pressure die cast aluminium (System lumen efficacy ≥105 <120 lm/Watt). Supplying, Installation, Testing & Commissioning of Flood Light, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 °C to 50 °C, internal surge protection of 5 KV L,N,E as per IEC 61000- 4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI ≥70, under voltage and over voltage protection, EMI-EMC as per CISPR -15, lenses for beam angle 30 deg-120deg as per the application and the project requirement., suitable tilt able fitting, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained

70 watt LED Flood Light

Supplying and fixing PVC batten/ angle holder including connections etc. as required. (PVC Batten/ Angle Holder)

supply & Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

4CX16sqmm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

4CX16sqmm

CABLE AND CABLE TRAY

Supply, testing, tagging, laying and commissioning following sizes of 1100 Volt grade, XLPE/PVC insulated multistrand Al. / Cu. Conductor armoured / unarmoured cables (As Per IS 1554 & IS 7098) in readymade RCC trench, in provided DWC pipe, RCC pipe hume pipe. on provided cable trays / ladders etc. as, required complete with clamps, hardware for fixing tagging, identification etc.

3 1/2c×120 sq mm AI A2XFY Armoured Cable(including spare)

3 1/2×50 sq mm A2XFY AI Armoured Cable (including spare)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 120 sq. mm (45mm)

3½ X 50 sq. mm (35mm)

Supplying and installing following size of perforated painted with powder coating M S cable trays with perforation not more than 17.5% in convenient sections,joined with connectors,suspended from the ceiling with M S suspenders including bolts & nuts,painting suspenders etc as required.

100mm width ×50mm depth×1.6 mm thickness

375mm width ×50mm depth×2.0 mm thickness

Supplying, Installation, Testing & Commissioning of following capacity passenger Machine room less (MRL) lift with regenerative drive as per CPWD General Specification for Electrical Works (Part- III Lift & Escalator) 2003, BIS Codes, NBC 2016 as amended upto date having provision for barrier free access as per Harmonised Guidelines & Standards for Universal Accessibility in India - 2021 of MoHUA, serving different floors in the lift shaft as per detailed specifications enclosed and as under including all other equipmentand accessories complete as required:- (i) Speed-1.5MPS

16 passenger's Lift

Desingn Supply, installation, testing and commissioning of VRF/VRV system including indoor / outdoor units, piping, electrical power disstribution, wiring, electrical panel, treated fresh air system etc. for aminity block ekamra all complete (Gr,1st 2nd floor)

DISEL GENERATOR (DG)

Supplying installation, testing and commissioning of silent type DG sets, AMF panel, bus ducting/ cables from DG sets to essential panel, synchronizing panel where required, DG set enclosure room sound insulation/ventilation/smoke exhaust as required, earthing of DG set system, control cabling, fuel tank/piping, DG set exhaust piping/ exhaust chimney as per CPCB norms, civil works connected with DG sets including foundation as required

UNINTERRUPTED POWER SUPPLY (UPS)

Supplying, installation, testing and commissioning of online 3 phase UPS system with 60 minutes back up including batteries, interconnecting cables, battery racks etc.

EARTHING

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/coke and salt) as required.

Charcole

25mm×05mm flat

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/coke and salt) as required.

Charcole

Supplying and laying 6 SWG G.I. wire at 0.50 Meter below ground level for conductor earth electrode, including connection/termination with Gl thimble etc. as required.

Supply and installation of rubber mats 12mm thick of size 2000mm×1000m×12mm thick electrical tested with test certificate.

Medicine with three years expiry date to be fixied in electrical control panel.

Supply and fixing of CO2 fire extingusisher with mounting clamps with pressure test certificate.

Supply and fixing of fire buckets with angular fabricated stand to fix 4 buckets in each stand for electrical fire protection as per standards of electrical inspectorate.

LIGHTENNG PROTECTION

Supply of Australian make PP-Stormking ESE-60 Early Streamer Emission type Advanced ESE terminal. It should be made up of SS 316L material and works on dual trust design. ESE terminal should comprised of separate electrically isolated dual SS 316L panels surrounding an SS Central Finial. ESE terminal should anticipate advanced triggering of min. 60 µs. ESE terminal central finial should be made from solid SS rod and its length should be min. 85mm above surrounding panels. ESE terminal SS 316L is low carbon steel which exhibit better corrosion resistance and are stronger at elevated temperatures performance. For isolation of terminal Delrin Adapter should be provided at bottom of terminal which should give higher dielectric strength. ESE terminal should be tested in European accredited test laboratory after 2011 as per revised NFC 17-102:2011 standard. Terminal should be tested for impulse current withstand test in CPRI for 40 kA. Terminal should be non electronic and does not require any external power supply.

Model: ESE-60 SS terminal.

Supporting Mast SS: The mounting pole used to support the lightning air terminal shall either be a supporting mast or Free standing mast at a ideal height of 5 mtr. above to be area protected or as per required level of protection. If any height restrictions are there then min height should be 2 mtr but radius of protection will change according to height. The mounting pole and supports shall be securely fixed with brackets and guy wires where required to withstand maximum locally recorded wind velocity. Mounting Pole shall be non corrosive and made up of medium class SS pipe of 2" dia having base plate at bottom for securely fixing mast on rooftop. Also PVC insulated metallic wire rope should be used for guying purpose. The down conductor shall pass through the centre of the pole for the entire length of the pole and it will be out at bottom of the pole. All the mounting accessories should be non-corrosive and made up of SS. Model: Supporting Guyed Mast: 5 mtr. x 2" dia with base plate, guying kit and mounting accessories

Supply of 70sq.mm cross section down conductor of single core flexible Copper cable made of min.990Nos copper strands of 3mm dia and having PVC insulation of min. 3mm thickness and overall dia of 16mm. It should be fixed using SS/GI saddles & fixtures every 0.5mtr. Model: Single core flexible Cu. Cable 70Sq.mm with SS saddles.

MODEL-MES CBR -17.2X3

Supply of 250Micron Copper Bonded Earth Rod 3Mtr long ×17.2 mm dia. CPRI Certified made up of high tensile low carbon steel with copper bonding of 99.9% electrolytic copper. Electrode should be tested in CPRI for 25KA short circuit current. Both the ends of electrode should be threaded and suitable for threaded Ground Rod Clamp .Ground rod clamp should be made up of brass. (MES-GFC ground Filling compound will be provided in 25 kgs Bags.)

Lightning Strike Recorder (L.S.R.): Supply of Australian make L.S.R. It should be non electronic& non- resettable type having 7 digits display &enclosed in an IP-67 enclosure with minimum sensitivity of 1000A & maximum capacity of 220KA tested on 8/20 micro second wave from as per IEC 60-1: 1989. It should be non electronic type and does not require external power supply for working. Supplier should do on site testing of LSR, where impulse generate should be used to show working of LSR. After impulse current passing through LSR it should change the counter reading. Model: LSR.

Supply and installation of UPVC Earthling Chamber with cover

Installation charges Installation cost of total lightning protection system * Mounting Lightning terminal on the Mast. * Fixing the Mast on the top of roof. * Lying the down conductor from the terminal to earth point. * Clipping of cable in the building wall. * Making 2 Nos. of 10 ft. earth installation. * Pouring of Chemicals with Earthing pipe into the hole. * Lying of cable to connect the earth pit.

CCTV SYSTEMS

Supply, installation, testing & commissioning of 4 MP IP Dome Camera. Image Sensor 1/3"CMOS, Fixed focal lens, IR Distance 30m, Video Compression S+265/H.265/H.264B/H.264M/H.264H, Audio Compression G.711A/G.711U, Image PAL:25fps(1920×1080, 1280×720, 704×576, 640×480), 3D DNR Yes, 1*RJ-45,10/100 Mbps self-adaptive Ethernet port, POE 802.3af,MAX 6W.

Supply, installation, testing & commissioning of 4 MP IP Bullet Camera. Image Sensor 1/3"CMOS, Fixed focal lens, IR Distance 30m, Video Compression S+265/H.265/H.264B/H.264M/H.264H, Audio Compression G.711A/G.711U, Image PAL:25fps(1920×1080, 1280×720, 704×576, 640×480), 3D DNR Yes, 1*RJ-45,10/100 Mbps self-adaptive Ethernet port, POE 802.3af,MAX 6W.

Supply, installation, testing & commissioning of 32 Ch. NVR 1 Sata. S+265/H.265/H.264 video formats, Connectable to the third-party network cameras, 1×HDMI and 1×VGA simultaneous outputs, 4 SATA interface, up to 8TB or higher, 1×RJ45 self-adaptive 10/100/1000 Mbps network interface.

Supplying, Installation, Testing and Commissioning of following 42" size LED display (LED monitor) industrial grade with 3840x2160 resolution or better, USB playback, bluetooth and miracast connectivity, 4X HDMI 2.0, DP 1.2, HDR 10/10+, brightness: 500-nits or better, Video wall mode should be available, contrast ratio: 1200:1, OPS slot, viewing angle (H/V): 170°/ 170°, response time less than 12ms, Display control shall be on monitor screen and programmable with remote (remote shall be supplied with system), Key Board, Optical Mouse, etc. as required.

Supply, Installation, Testing & Commissioning of Central Control Station consisting of the following accessories, PC i7 Intel Processor, 2.93 Ghtz or better, 8GB RAM (Expandable), 1TB HDD, 2GB NVIDIA graphic card, CD/DVD R/RW Drive & 32" inch TFT colour monitor, laser printer, cordless key board, mouse, Windows 10 operating system, etc. all complete

SITC of - 24 Port Network Switch. Network Switch shall be PoE 1G network switch having support for protocols such as ARP, DHCP, RSTP etc, & provide cybersecurity features to attain network security & reliability, having upto 4 SFP port for fibre connectivity with all necessary accessories such as network rack, patch panels, patch chords etc. as per requirement.

Supply, Laying, Testing & Commissioning of following Signal & communication cable, CAT 6A FRLS Cable.

Supply, installation, testing & commissioning of Cat 6A 24-port loaded Jack Panel / PATCH PANEL

Supply, installation, testing & commissioning of PATCH CORD SWITCH END FOR CAMERA 1 MTR

Supply, installation, testing & commissioning of PATCH CORD CAMERA END 2MTR

Supply, installation, testing & commissioning of 32U loaded Rack

Accessories such as including clips, mounts, tags, required camera brackets etc. complete as per direction of Engineer in charge

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes conforming to IS:15778, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.(Make: ASTRAL /SUPREME/ORIPLAST OR EQUIVALENT. )

15 mm CPVC SDR 11 pipes

20 mm CPVC SDR 11 pipes

25 mm CPVC SDR 11 pipes

32 mm CPVC SDR 11 pipes

Providing all materials, labour, T&P for laying/ fixing of following dia UPVC pipes Sch-80 as per ASTM-D-1785/2004 including fixing of required size UPVC fittings like bend, Tee, elbow, offsets etc. and the same fixed on wall or floor with holder bat clamps screw etc. as per specification and direction of Engineer-in-charge.(Make: ASTRAL /SUPREME/ORIPLAST OR EQUIVALENT. ).

25 mm UPVC sch 80 pipes

32 mm UPVC sch 80 pipes

40 mm UPVC sch 80 pipes

50 mm UPVC sch 80 pipes

Providing all materials, labour, T&P for laying/fixing of following dia UPVC pipes as per IS-4985 with ISI mark including fixing of required size UPVC fittings like,bend,Tee,elbow,offsets,etc. and the same fixed on wall or floor with holder bat clamps screw in all floors or laying in trenches including excavation of earth work in all kinds of soil & backfilling the trenches as per specification & testing the joints with required water presure etc. as per specification and direction of Engineer-in-charge.(Make: ASTRAL /SUPREME/ORIPLAST OR EQUIVALENT. ).

50mmP.V.C.S.W.R.Pipe 6kg/cm2

Supplying all labour T & P for Cutting grooves through the wall or floor for taking PVC pipes and mending good the damages etc.all complete.

Wall & floor cutting

Supplying all labour T & P for Cutting holes through the brick or laterite, masonarry wall for taking sand cast iron (SCI) pipes or A.C pipes and manding good the damages etc.all complete.

For 15mm to 50mm dia pipe to pass in 125mm to 250mm thick wall

For 75mm to 150mm dia pipe to pass in 250mm thick wall

Supplying all materials, labour, T&P and cutting hole in R.C.C floors, roofs, etc upto 19 cm thick for passing G.I. Pipes / P.V.C pipes and fittings etc and repairing the holes after insertion of pipes etc with cement concrete (1:2:4 ) including finishing complete so as to make it leak proof as per direction of the Engineer-in-charge.

Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR Type B soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing,Excluding earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer-In-Charge.(Make: ASTRAL /SUPREME/ORIPLAST OR EQUIVALENT. )Rain Water Pipe .

110mm U.P.V.C.S.W.R.Pipe 6kg/cm2 .

110mm U.P.V.C.S.W.R. Door bend

110mm U.P.V.C.S.W.R.45 degree bend

110mm U.P.V.C.S.W.R. plain bend

110mm U.P.V.C.S.W.R. Door Tee

110mm U. P.V.C. Clip/Clamp

110 mm U. P.V.C.S.W.R. cowl

Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR Type B soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing,Excluding earthwork in excavation in all kinds of soil and refilling of trenches , Sewer ,waste water &stack line pipe from bathroom & toilet etc. as per specification and direction of Engineer-in-charge. .(Make: ASTRAL /SUPREME/ORIPLAST OR EQUIVALENT. )

110mm U.P.V.C.S.W.R.Pipe 6kg/cm2

75mm U.P.V.C.S.W.R.Pipe 6kg/cm2

110mm U.P.V.C.S.W.R. plain bend

110mm U.P.V.C.S.W.R. Door bend

110mm U.P.V.C.S.W.R. DoorTee

110mm U.P.V.C.S.W.R. plain Y Tee

110mm U.P.V.C.S.W.R. coupler

110mm U.P.V.C.S.W.R.45 degree bend

110mm U.P.V.C.S.W.R. P -trap

110mm U. P.V.C. Clip/Clamp

110mm U.P.V.C.S.W.R. Off set bend

110mm U.P.V.C.S.W.R. plain Tee

110mm U.P.V.C.S.W.R. cowel

110mmx 75mmx25mm U. P.V.C.S.W.R. Multi -trap

110x75mm U.P.V.C.S.W.R. reducer socket

110mm U.P.V.C.S.W.R. Door Y Tee

75mm U.P.V.C.S.W.R. plain bend

75mm U.P.V.C.S.W.R.45 degree bend

75mm U.P.V.C.S.W.R. plain Y Tee

Supplying, fitting and fixing of following types CP other fittings of approved make and quality confirming to relevant IS specifications with leak proof threaded joints including the cost of all materials, cost of labour, conveyance, taxes, loading, unloading, T&P, etc, all complete as per the direction of Engineer-in-Charge.

15mm dia C P brass 2 Way bib cock with wall flange

15 mm CP brass Angular Stop Cock

Hand shower (Health Faucet) with 8mm dia 1.00 mtr long flexible Tube & wall hook with NRV.

15mm dia C.P. brass Piller cock Auto Closing System

Auto Closing Concealed Urinal Flush Valve With wall Flange.

C P.Robe Hook

Waste Coupling 32mm size Full Thread with 130mm height.

Soap Dish (Polycarbonate)

Toilet Paper Roll Holder with Shelf.

Pillar Cock with Extended Lever Handle ,For PH Toilet.

Soap Dispenser,0.8L Capacity,ABS finish White/Smoked

C P Bottle TRAP 32 mm size with 250mm& 190mm Long wall Connection Pipes &Wall Flange.

15mm dia Bib cock with wall flange

20mm Concealed Stop cock with wall flange

15mmCP brass Bathtub Spout with wall flange

20mmx600mm C P brass towel rail

Sink Cock with Regular Swinging Spout( Wall mounted Model) with wall flange for Kitchen sink.

Over Head Shower of 120mm round shape single flow(Face Plate Stainless Steel & ABS bodyin chrome finish) with rubit cleaning system &Shower Arm 190mm Long with flange(Jaquar ) Cat No.OHS -1663&SHA-4839(1525/-+1100/-)

Paper Towel Dispenser Capacity:-400-600C/Z towels,Material:AISI 304 Stainless Steel finish:Satin,

Supplying, fitting and fixing of following types fittings of approved make and quality confirming to relevant IS specifications with leak proof threaded joints including the cost of all materials, cost of labour, conveyance, taxes, loading, unloading, T&P, etc, all complete as per the direction of Engineer-in-Charge.

15mmx25mm longCP Extention piece

15mm PVC Connection Pipe

125mm CP grating

15mm C.P. Flange

Supplying all materials labour T & P fitting & fixing of white glazed vitreous china ware porcelain counter basin approved make including all jointing materials and cost,taxes,conveyance etc all complete as per P.H. specification and direction of Engg-in-charge. Make JAQUAR/HINDWARE/PARRYWARE OR EQUIVALENT

Porcelain Under Counter Basin Size : 485x370x205mm

Porcelain Counter Top Basin Size: 425x340x175mm

Supplying all materials labour T & P fitting & fixing of white glazed vitreous china ware porcelainWall Hung Basin & Half pedestal of approved make including all jointing materials and cost, taxes, conveyance etc all complete as per P.H. specification and direction of Engg-in-charge. Make JAQUAR/HINDWARE/PARRYWARE OR EQUIVALENT

Wall Hung Porcelain Basin Size : 620x480x185mm & Half Pedestal.

Supplying all materials, labour, T&P and fixing the following vitreous china Wash Down Water Closet (European type W.C. pan) with integral 'p' trap to the floor with wooden plug and chromium plated pedestal screws including jointing the trap with soil pipe in cement mortar (1:1) fixing plastic seat and cover for wash down water closet with chromium plated brass hinges and rubber buffers including polishing etc all complete as per specification and direction of the Engineer-In-Charge. Make JAQUAR/HINDWARE/PARRYWARE OR EQUIVALENT.

Rimless Back to Wall WC with UF Soft Close Slim SeatCover, Hinges,Fixing Accessories and Accessories Set.Size:360x575x410mm,P trap-180mm

Supplying all materials, labour, T&P and fixing vitreous china water closet, squatting pan (Indian type W.C pan/Orissa pattern squatting pan) duly embedded in cement concrete (1:4:8) using 4cm size hard granite metal including , fixing 100mm dia 'p' or 's' trap (with/without 50mm dia horn) for water colset squatting pan including jointing the trap with pan in cement mortar (1:1) cutting the floor and mending good the damages etc all complete as per specification and direction of the Engineer-In-Charge. Make JAQUAR/HINDWARE/PARRYWARE OR EQIVALENT

Orissa PanSize:440x590x250mm.

Supplying all materials, labour, T&P and fixing Flat back large pattern urinal including connecting the urinal with 50mm dia pvc waste pipe, including cutting holes in walls land making good the damages with supply of wooden plugs, screws and cement etc all complete as per specification and direction of the Engineer in charge. Make: JAQUAR / HINDWARE / PARRYWARE OR EQUIVALENT

Urinal (Back Inlet) with Fixing Accessories,Size:385x325x635mm.

Supplying all materials, labour, T&P and fixing Sensor Conceaied type Flushing Valve for Standing Urinal Complet Set , including cutting holes in walls land making good the damages with supply of wooden plugs, screws and cement etc all complete as per specification and direction of the Engineer in charge. Make JAQUAR/HINDWARE/PARRYWARE OR EQUIVALENT.

Sensor Concealed Type Flushing Valve for Western Commode Complete Set with Provision for Mannual Operation Also(Battery Operated).

Suplying all materials, labour. T&P for fitting and fixing Single piece Slim Concealed Cistern with Floor Mounting Frame,Instalation Kit and "S" type Drain Pipe Connection Set(Excluding Flush Control Plate) with all fitting, fixtures etc. complete in all respect including cost, conveyance and taxes of all materials etc. complete as per specification and as per direction of Engineer-in-charge.In EWC. Make JAQUAR /HINDWARE / PARRYWARE OR EQUIVALENT.

Suplying all materials, labour. T&P for fitting and fixing Single piece Concealed Cistern Body (Front or Top Actuation) with Instalation Kit, Flush Pipe ( Excluding Flush Control Plate) with all fitting, fixtures etc. complete in all respect including cost, conveyance and taxes of all materials etc. complete as per specification and as per direction of Engineer-in-charge.In Orissa Pan Make JAQUAR /HINDWARE / PARRYWARE OR EQUIVALENT.

Supplying all materials, labour, T&P and fixing Flush Control Plate, including cost, conveyance, taxes of all materials complete as per specification and direction of E.I.C. Make JAQUAR /HINDWARE / PARRYWARE OR EQUIVALENT.

Flush Control Plate,

Supplying all materials, labour, T&P and fixing standard sized Shower mixer with provision for connection to overhead shower only of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification complete as per direction of Engineer-in-charge.Make JAQUAR/ROCA/GROHE/KOHLER OR EQUIVALENT

Aquamax Concealed body of Single Liver Shower Mixture with 3-Way diverter with exposed part

Providing and fixing 5"x5" size Square type stainless steel floor clean out Cover with Seal for floor /nahani trap etc complete as per specification and direction of the Engineer in charge.

Providing all materials, labour, T&P for fixing of Bevelled edge mirror mounted on 6mm thick AC back sheet & CP cup screw with PVC wall plugs in all floor including cost, conveyance, taxes of all materials complete as per specification and direction of E.I.C.

Mirror (600x450mm) of 6mm thick

Mirror (600x600mm) of 6mm thick.

Fixing of Following size Brass / Gun metal ball Valve confirming to IS : 781-1995 of of approved make as per specification complete as per direction of Engineer-in-charge.( Make: SHAKTI /ZOLOTO/VENUS or Equivalent)

25mm dia Brass / Gun meta ball Valve

32mm dia Brass / Gun meta ball Valve

40mm dia Brass / Gun meta ball Valve

50mm dia Brass / Gun meta ball Valve

Fixing Rotational moulded polyethylene double layer cylendrical vertical water tank storage of required capacity conforming to IS : 12701--1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc, including hoisting upto a height of 5 metres above ground level and placing the tank to the required position etc all complete as per specification and direction of the Engineer in charge. make: Sintex/Astral/Ashribad or Equivalant.

Fixing Rotational moulded polyethylene double layer cylendrical vertical water tank storage of 5000 ltr capacity

Fixing Rotational moulded polyethylene double layer cylendrical vertical water tank storage of 2000 ltr capacity

Supply and fixing all materials, labour, T & P and providing Granite urinal partition Slab of size 500mm (W) X 1200 mm(H)etc all complete as per direction of the Engineer-In-Charge.

Providing all materials, labour, T&P for fitting and fixing of white glazed vitreous china water closet (European pattern) 'P' or 'S' type 660MMX350MM880MM SIZE with cistern & seat cover, wash hand basin of size 460mmx360mmX180MM SIZE with one pair basin bolt,waste Coupling, 2 nos. Hinge Rail & 4 nos. grab bars 692 mm long including supply of sutaible PVC wall plug and Brass screws etc. suitable for handicapped toilets in Ground floor etc. all complete including cost, taxes and conveyance as per specification all complete as per direction of Engineer-in-charge. Make JAQUAR /HINDWARE / PARRYWARE OR EQUIVALENT.

Supply all materials, labour, T&P and providing fitting & fixing (Aquaguard) pure Chill 80 PSS UV of size 750x570x1350 mm height with water storage capacity 120 liters along with 2 nos of fancets 1 for cold water and 1 for normal water including a flow of 1.5 ltr per minute etc. all complete as per approved drawing, specification and direction of the EIC.Make:-BLUESTAR/KENT/AQUA GUARD OR EQUIVALENT.

Supplying all materials, labour, T&P and fixing Squatting urinal including connecting the urinal with sewer pipe, including cutting holes in walls land making good the damages with supply of wooden plugs, screws and cement etc all complete as per specification and direction of the Engineer in charge. Make: JAQUAR / HINDWARE / PARRYWARE OR EQUIVALENT

Squatting Urinal with Fixing Accessories ,Size:450x350x100mm .

Providing all materials, labour, T&P for fitting and fixing of 3 lit 3kw instant type hot water geyser including all necessary nut, bolts , piping acceosories etc complete.Make-JAQUAR / CROMPTON /HAVELS /EQUIVALENT )

BORE WELL -Construction of 1 No production wells including scientific source finding through consolidated and unconsolidated rock with down the hammer drilling rig or combination rig with PVC pipe with all acessories

Labour for drilling a perfectly vertical bore hole of specified dia for a specified depth below ground level through consolidated and unconsolidated rock with down the hole hammer drilling rig or combination rig as required to suit the site condition as per the direction of the Engineer in charge including use of own rig with its accessories, tools and plant and consumables etc for lowering of 200mm/150mm dia G.I/P.V.C/M.S casing pipes for housing fitted with socket and with or without well screen as per the necessity for soft, medium, hard and boulder formation (G.I/ P.V.C/ M.S casing pipes if required to prevent collapse of overburden is to be provided by the contractor including lowering and withdrawing after completion of the tube well), 200mm dia to 400mm dia in overburden portion including packing of gravel supplied by the contractor for 400mm dia bore only

Labour for drilling of 200mm dia & 150mm dia bore from '0' mtr. to '100' mtr.

Lowering the following size of G.I/P.V.C/M.S housing pipes with or without slotted pipes as per the necessity from ground level up to 45.00m depth and fitted and fixed up in perfectly vertical position including cutting and threading of pipes and slotted pipes and supplying and fixing all jointing materials, tools and plant etc all complete and keeping the top of casing pipe threaded including plugging tube wells to prevent entry of foreign materials

Lowering of 200mm (8'') dia PVC plastic pipes Sch-80 as per ASTM-D-1785/2004 upto required depth.

Supplying polyvinyl chloride pipes as per ASTM-D-1785-89 having threads in accordance with DIN 2999 part-1/DIN-42225 part-II specification length of pipe (laying length) will be 3 mtrs. The pipes shall be supplied with both external and threaded with free socket. The pipe having external thread at one end i.e female and or belled end. The female end having internal thread is to be belled in order to accept the male end while jointing pipes with a bore threading shall be provided with a greave at the roof of the male thread accomodate flexible PVC/Rubber 'O' ring to make the joint water tight colour of the pipe shall be blue. The name of the manufacture along with batch No class of pipe shall be stranded legibly of each pipe length.

Cost of 200mm dia (Sch.80) PVC Casing Pipe.

Cleaning and developing the tube well with supply of compressor worked till clear and adequate discharge is obtained from the tube well including supply and use of all necessary equipment and labour as per direction of the Engineer in charge.

Supplying all materials, labour, T&P and providing sanitary sealing by cement concrete grouting of annular space around GI/PVC/MS housing pipe upto 5m below ground level (as per drawing) to plug the bore hole including cost of cement all complete as per direction of the Engineer in charge. Minimum one metre of casing pipe to be inserted in the bore into the rock at the bottom to ensure sanitary sealing .

Providing Pumping System for Bore Well.

Supplying all materials, labour, T&P and providing, fitting and fixing submersible pump with squirrel cage induction type submersible type submersible electric motor to run on 3 phase/1 phase line voltage ranging from 320 volt to 450 volt conforming to IS: 8034/89 with following specifications with suitable control panel, jointing with GI/PVC/HDPE pipes, electrification, testing, commissioning, trial running, conveyance of all materials to worksite, payment of taxes etc all complete as per specification and direction of the Engineer in charge. 3 H.P.@ 9821.62/HP (Provisional) Make:- CROMPTON/KRILOSKAR/TEXMO OR EQUIVALENT.

Control Panel (BCH/CROMPTON/C&S Anmol OR EQUIVALENT.)

HDPE Pipe

Cable

Tochan Rope(8mm)

Acessories(Clamp,Bore Cover,S/S Nipple,Bend,Socket ,etc.)

Plumber Charges.

Providing & Constructing UGR of 4.20m x2.00mX1.50m size(10000 ltrs.Capacity) including earth work in excavation, back filling,RCC Wall in C C (1:1.5;3) in four sides to make chamber, Plain Cement Concrete (1:3:6) 100mm thick in bottom of chamber with 40mmdown graded Crusher broken hard granite metal, inside 6mm thick cement plaster 12mm thick in CM 1:4 & neat cement punning , Top slab in RCC (1:1.5:3) 125mm thick with necessary centering & shuttering, TMT steel reinforcement 10 mm dia both way, SFRC manhole cover of size 600mmx600mm with frame, makingthe floor of chamber with necessary slope complete with all materials, labour, tools, plant, royalty, curing, etc. in all respects as per the direction of Engineer-in-charge.

Earthwork Excavation of the foundation pit in all kinds Soil. Earthwork Excavation of the foundation(1st depth up to 1.5mt.) Foundation -1x5.90mx3.70mx1.70m=37.11 Cum.

Earthwork Excavation of the foundation(2nd depth from 1.5mt.to 3.0mt.) Foundation -1x5.10mx4.20mx1.0m=21.42 Cum.

100 mm thick Sand Filling well watered and rammed. Foundation-1x5.30mx3.10mx0.10m=1.64 Cum.

100 mm thick Plain Cement Concrete (1:3:6) Using 40mm CBHG Metal Foundation-1x5.30mx3.10mx0.10m=1.64 Cum.

RCC with Cement Concrete (1:1.5 :3) using 12mm Size crusher broken granite chips including hoisting &laying,all complet.( Foundation, RCCwall &cover slab) Foundation-1x5.00mx2.80mx0.15m=2.10Cum. RCC Wall-1x2(4.60+2.40)mx(0.25+0.15)m/2x1.50m=4.20Cum Roof Slab-1x4.50mx2.30mx0.125m=1.29Cum.

Providing Centring &Shuttering for RCC Foundation&Plinth band . PCC-1x2(5.30m+3.10m)x0.10m=1.68Sqmt. RCC-1x2(5.00m+2.80m)x0.15m=2.34Sqmt.

Providing Centring &Shuttering for RCC Wall &Fin RCC Wall (Outside)-1x2(4.60+2.40)mx1.50m=21.00Cum. RCC Wall (Inside)-1x2(4.20+2.00)mx1.50m=18.60Cum.

Providing Centring &Shuttering for RCC Roof Slab. Roof Slab-1x4.20mx2.00m=8.40Sqmtr. 1x2(4.50m+2.30m)x0.125m=1.70Sqmtr.

Supplying HYSD Steel Reinforcement and cutting ,bending, binding,tying the grill including all the cost and as per direction of Engineer-in-charge.(@1Quintal/cum of RCC Work)

Filling Foundation & Plinth with excavated earth including watering. 37.11-(1.64+1.64+14.90)=22.21 Cum.

Disposal of surplus/ excavated materials by mechanical means within 5km. Lead away from the site including cost of all labour , T&P complete as per the direction of the Engineer-in-charge. 37.11-22.21=14.90Cum.

6 mm thick Cement Plaster in CM (1:4) to RCC surface finished smooth including closed deep chipping & slurry treatment and neat Cement Punning to inside surface of UGR. RCC Wall (Inside)-1x2(4.20+2.00)mx1.50m=18.60 Sqmtr. Bottom Floor-1x4.20mx2.00m=8.40Sqmtr.

Supplying ,Fitting & Fixing of SFR Polypropylene Foot Step iron inside UGR.

Cost towards Factory made Precast RCC Cover Slab(two piece ) of outer size 350mmx700mm of 90 mm thick with Factory made Precast RCC Frame of outer size 915mmx915mm of 150mm thick with grove cutting suitable to hold Cover Slab.(Rs.4000/- +15%+1%)

Supply all materials, labour, T&P and providing fitting & fixing Centrifugal Monoblock Pump set in cluding all fittings to lift water from UGR to Overhead Storage Tank .1 HP or Required size. ( Provisional ) Make:- CROMPTON/KRILOSKAR/TEXMO OR EQUIVALENT.

Supplying all materials, labour, T & P and constructing Gully trap chamber of inside size 300mmx300mmx450mm with 300mm x 300mm size SFRC cover with frame and embaded in concret ,100mm foundation concrete (1:4:8) using 40mm size h.g. metal on bed aound trap over 100mm Sand filling , Fly Ash brickwork in CM (1:5) with Fly Ash bricks having crushing strength not less than75kg/cm2 in P&F,benching & chanelling in CC (1:2:4) mix using 12mm size h.g. chips and inside 12mm thick cement plastering (1:3) finished with neat cement punning, cement plastering (1:3) to outside wall surface including fixing 110mm size PVC gully trap, 150mm x150mm C.I gratig, earth work in excavation in all kinds of soil and refilling the cavity around the chamber including watering etc. all complete as per aproved drawing, specification and direction of Engineer-in-charge.

Supplying all materials, labour, T & P and constructing Inspection chamber of the following inside size with CC (1:4:8) mix using 40mm size h.g. metal on bed over 100mm Sand filling, Fly Ash brickwork in CM (1:5) with Fly Ash bricks having crushing strength not less than75kg/cm2 in P&F , moulding and shaping the channel inside and benching with CC (1:2:4) using 12mm size h.g. chips, 12mm thick cement plastering (1:3) finished with Cement punning to inside , cement Plastering (1:3) to outside , R.C.C. cover slab in (1:1.5:3) using 12mm size h.g. chips with SFRC Circular(Heavy Duty)man hole cover with Frame embaded in concrete , earth work in excavation in all kinds of soil and refilling the cavity around the chamber including watering ,curing, conveyance of all materials to worksite , payment of royality , taxes etc. all complete as per aproved drawing , specification and direction of Engineer-in-charge. Inside size 750mm x750mm x450mm.

Supplying all materials, labour, T&P and constructing Circular RCC MHChamber of size 1.20 mtr dia x 0.90 mtr depth including cost of SFRC Man Hole Cover embaded in concret , cement concrete (1:3:6) using 40 mm size HG metal on bed over 100mm Sand filling , ,RCC cover slab in (1:2:4) mix using 12 mm size H.G chip moulding and shaping the channel inside and benching with CC (1:2:4) mix using 12 mm size H.G chips, 12 mm thick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside ,200mmthick RCC Foundation, 200mm Thick RCC Wall&150mmthick RCC cover slab in (1:1.5:3) mix using 12 mm size H.G chips ,6mm thick cement plaster1:4 including Cement punning toinside RCC Wall,12mm thick Cement Plaster to outside RCC wall, fitting & fixing of S.F.R. poly popylene foot step iron, Earth work in all kinds of soil and refilling the cavity around the camber including watering, curing, conveyance of all materials to worksite payment of royalty, taxes etc. all completed as per approved drawing, specification and direction of Engineer-in-charge.

Inside size 1200mmx900mm

Addl depth of 0.10m upto 1.50m depth(0.10mtr.=1no.)

Providing all materials, labour, T&P and laying of Centrifugally cast (spun) RCC non pressure pipes of class NP3 with socket & spigot ends confirming to IS-458 with ISI mark in standard lengths suitable for push on joints including lowering the pipes in to trenches to required depth below G.L, with proper allignment & gradient, testing, commissioning, de-watering (if required) including rubber gasket as per IS-5382/1985 with ISI mark with all taxes & duties etc. all complete as per specification & direction of EIC including Providing and laying in trench cement concrete ( 1:3:6 ) with 40mm size hard granite metal in the following type of bedding and hunching for RCC NP3 Spigot socket concrete pipes of the following internal diameter including curing complete as per specification & direction of E-i-c.

150mm dia pipe

200mm dia pipe

Earthwork in excavation in all types of soil for site leveling, foundation, pits, trenches and other civil works upto and including 1.5metre depth and stacking the soil upto a lead of 100 metre and including dewatering, removing slush, shoring and strutting (as required), complete as per specification and as directed by the Engineer-In-Charge. (For Laying of 150mm diaHume sewer pipes&110 mm UPVC Sewer Pipe) 150mm-1x35.00mtr.x1.0mtr.x1.5mtr=52.50Cum

110mm-1x30.00mtrx.0.60mtrx.0.90mtr=16.20 Cum.

Providing and laying in trench Cement Concrete(1:3:6) with12mm.size crusher brokn Granite metal for all round encasing 110mm OD UPVC SWRpipes and hunching 150mm internal dia RCC Humepipes including concrete for bedding and curing complete as per PH specification and drawing. 110mm OD UPVC SWRpipes(All round 0.30mx.30m ) 30.00mx.30mx.30m=2.70cum.- 0.29 cum.=2.41Cum. 150mm-1x35.00mtr.x1.0mtr.x1.5mtr=52.50Cum 150mm internal dia RCC Humepipes .Bellow Pipe Rectangular Portion 500mm wide,100mm thick&Cradaling 100mm thick Bedding-1x 35Mtr.x0.50Mtr.x0.200Mtr.=3.50Cum. Deduct Pipe- 1x35Mtr.x0.786 x0.5x0.04 =0.55Cum. Net Quantiy- 3.50cum.-0.55 cum=2.95 cum. Total Quantity- 2.41cum.+2.95 cum.=5.36 cum.

Rigid smooth centring and shuttering for R.C.C. works and dismantling then after casting including cost of materials,labour & T & P etc. all complete. R.C.C. Foundation, Plinth Band, Footings, Bases of Columns, Mass Concrete & Precast Slabs etc. in Ground Floor. 110 mmUPVC SWR Pipe- 2x30mx 0.30m=18.00 Sqm, 150 mmHume Pipe- 2x35mx0.200m=14.00 Sqmtr.

Filling Foundation & Plinth with excavated earth in trench after completion of laying of Pipe line including watering. Total Excavated Earth Qnty.- 68.70 Cum. Deduct Pipe &Bedding. Bedding - 2.95Cum.+2.41 Cum=5.36Cum. 150mm dia Hume pipe- 35mtr.x0.786x0.04=1.10 Cum. 110 mmUPVC SWR Pipe- 30mtr.x0.786x0.012=0.29 cum. Total deduction Qty.=6.75 cum. Net Filling Quantity; 68.70Cum.-6.75 Cum=61.95 Cum.

Providing & Constructing SEPTIC TANK of 8.70m x 2.10m X2.0m inner size including earth work in excavation, back filling,RCC Wall in C C (1:1.5;3) in all sides to make chamber, Plain Cement Concrete (1:3:6) 100mm thick in bottom of chamber with 40mmdown graded Crusher broken hard granite metal, inside 6mm thick cement plaster 12mm thick in CM 1:4 & neat cement punning , Top slab in RCC (1:1.5:3) 125mm thick with necessary centering & shuttering, TMT steel reinforcement 10 mm dia both way, SFRC Circular manhole cover(Heavy Duty ) with frame, makingthe floor of chamber with necessary slope complete with all materials, labour, tools, plant, royalty, curing, etc. in all respects as per the direction of Engineer-in-charge.

Earthwork Excavation of the foundation pit in all kinds Soil. Earthwork Excavation of the foundation(1st depth up to 1.5mt.) Foundation -1x10.50mx3.90mx1.50m=61.43Cum. Inlet Chamber:-1x.30mx.30mx0.50m=0.05Cum.

Earthwork Excavation of the foundation(2nd depth from 1.5mt.to 3.0mt.) Foundation -1x10.50mx3.90mx0.80m=32.76Cum. Foundation -1x6.60mx3.90mx0.30m=7.72Cum.

100 mm thick Sand Filling well watered and rammed. Septic Tank-1x10.50mx3.90mx0.10m=4.10Cum Inlet Chamber:-1x1.20mx1.40mx0.10m=0.17Cum. Out let Chamber:-1x2.90mx1.00mx0.10m=0..29Cum.

100 mm thick Plain Cement Concrete (1:3:6) Using 40mm CBHG Metal Septic Tank-1x9.90mx3.30mx0.10m=3.27Cum Inlet Chamber:-1x1.10mx1.30mx0.10m=0.14Cum. Out let Chamber:-1x2.70mx0.90mx0.10m=0.24Cum.

RCC with Cement Concrete (1:1.5 :3) using 12mm Size crusher broken granite chips including hoisting &laying,all complet.( Foundation, RCCwall &cover slab) Septic tank Base-1x9.70mx3.30mx0.15m=4.51Cum. Inlet Chamber base:-1x1.10mx1.00mx0.15m=0.17Cum. Out let Chamber Base:-1x2.50mx0.80mx0.15m=0.30Cum. InletSide Wall-1x2.90mx0.30mx2.60m=2.26Cum. Out Let Side Wall-1x2.90mx0.30mx1.70m=1.48Cum. Long Side Wall-2x9.50mx0.30mx2.30m=13.11Cum. Inlet Chamber Wall-1x2.90mx0.10mx0.30m=0.09Cum. Out Let Chamber Wall-1x3.70mx0.20mx0.30m=0.22Cum. Middle Wall-1x2.10mx0.15mx2.00m=0.63Cum. BaffleWall-1x2.10mx0.075mx0.60m=0.09Cum. Scum Wall-1x2.10mx0.075mx0.75m=0.12Cum. Septic tank Roof Slab-1x9.90mx2.50mx0.125m=3.09Cum. Inlet Chamber Cover Slab:-1x1.10mx1.00mx0.075m=0.08Cum. Total Qnty.-26.15 CUM. Deduction Opennings Man Hole-4x0.786x0.50mx0.50mx0.125m=0.10Cum. Wall Openning-2x0.30mx0.30mx0.15m=0.03Cum. Total Deduction Qnty.=0.13Cum. Net Qnty.26.15Cum.-0.13Cum=26.02Cum.

Providing Centring &Shuttering for RCC Foundation&Plinth band . Plain Cement Concret Septic tank Base-2x13.20mx0.10m=2.64Sqmt. Inlet Chamber base:-1x3.70mx0.10m=0.37Sqmt. Out let Chamber Base:-1x4.50mx0.10m=0.45Sqmt. RCC Base Septic tank Base-2x12.80mx0.15m=3.84Sqmt. Inlet Chamber base:-1x3.10mx0.15m=0.47Sqmt. Out let Chamber Base:-1x4.10mx0.15m=0.62Sqmt.

Providing Centring &Shuttering for RCC Wall &Fin OUT SIDE InletSide Wall-1x2.70mx2.60m=7.02Sqmt. Out Let Side Wall-1x2.70mx1.70m=4.59 Sqmt. Long Side Wall-2x9.30mx2.30m=42.78 Sqmt. Inlet Chamber Wall-1x3.10mx0.30m=0.93 Sqmt. Out Let Chamber Wall-1x4.30mx0.30m=1.29 Sqmt. INSIDE InletSide Wall-1x2.10mx2.60m=5.46Sqmt. Long Side Wall-2x5.70mx2.30m=26.22Sqmt. Middle Wall-1x2.10mx2.00m=8.40 Sqmt. 2nd Compartment Wall-1x9.90mx2.00m=19.80Sqmt.. Inlet Chamber :-1x3.60mx0.30m=1.08Sqmt. Out let Chamber :-2x0.60mx0.30m=0.36Sqmt. BaffleWall-1x2.10mx1.28m=2.69 Sqmt. Scum Wall-1x2.10mx1.58m=3.32 Sqmt.

Providing Centring &Shuttering for RCC Roof Slab. Septic tank Roof Slab-1x9.90mx2.50m=24.75Sqmt. Septic tank Roof Slab Side-1x24.80mx0.125m=3.10Sqmt.

Supplying HYSD Steel Reinforcement and cutting ,bending, binding,tying the grill including all the cost and as per direction of Engineer-in-charge.(@1Quintal/cum of RCC Work)

Filling Foundation & Plinth with excavated earth including watering. 101.96 Cum.-(4.56+3.65+57.75)Cum =36.00Cum.

Disposal of surplus/ excavated materials by mechanical means within 5km. Lead away from the site including cost of all labour , T&P complete as per the direction of the Engineer-in-charge. 101.96 Cum.-36.00 Cum.=65.96 Cum.

6 mm thick Cement Plaster in CM (1:4) to RCC surface finished smooth including closed deep chipping & slurry treatment and neat Cement Punning to inside surface of Septic Tank. Septic tank Floor-1x5.70mx2.10m=11.97Sqmt. Septic tank wall-1x15.60mx2.30m=35.88Sqmt. Septic tank wall-1x2.85mx2.10m=5.99Sqmt. Septic tank wall-1x2.90mx2.00m=19.80Sqmt. BaffleWall-1x2.10mx1.35m=2.84 Sqmt. Scum Wall-1x2.10mx1.65m=3.47 Sqmt. Inlet Chamber :-1x3.60mx0.30m=1.08Sqmt. Out let Chamber Floor :-1x2.10mx0.80m=1.68Sqmt. Out let Chamber wall :-2x1.0mx0.30m=0.60Sqmt.

Supplying ,Fitting & Fixing of SFR Polypropylene Foot Step iron inside UGR.

Supplying fitting & fixing ofCircular SFRC Man hole cover with frame (Heavy duty)

Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR Type B soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing,Excluding earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer-In-Charge.(Make: ASTRAL /SUPREME/ORIPLAST OR EQUIVALENT. )Vent Pipe (4Nos.)

110mm U.P.V.C.S.W.R.Pipe 6kg/cm2 .

110 mm U. P.V.C.S.W.R. cowl

110mm U.P.V.C.S.W.R. plain Bend

Providing & Constructing SOAK PIT of 1.20m dia x1.50m deep size including earth work in excavation, back filling,Using 50mm thickRCC Well ring with nominal reinforcement in C C (1:1.5;3) using 12mm size CBHG Chips to make chamber, and filling with BRICK KHOA 50mm to 100mm size up to 1.20Mtr. depth ,filling Cavity arround the pit with excavated materials complete with all materials, labour, tools, plant, royalty, curing, etc. in all respects as per the direction of Engineer-in-charge.

Supply all materials, labour, T&P and providing fitting & fixing Pressure Booster Pump set in cluding Hydropneumatic Tank,Pressure Switch,Pressure Gauge, Y-Strainer etc. all fittings to Provide reqired water pressure to Toilet/Bath room from Overhead Storage Tank .1 HP Capacity . ( Provisional ) Make:- CROMPTON/KRILOSKAR/TEXMO OR EQUIVALENT.

Supplying, installing, testing and commissioning of 1000 litres per hour Reverse Osmosis (RO) based Water Treatment Plant, complete in all respects, suitable for continuous operation, including design, manufacture, erection, interconnections, testing and commissioning to meet specified treated water quality Training of operating personnel etc. complete as per direction of Engineer in charge. The scope (1 Lot) comprises supply of a complete water treatment package including one Multi Grade Sand Filter, one Iron Removal Filter and one Activated Carbon Filter, each fabricated in SS 304 pressure vessels of size 16" × 65" with 3 mm shell thickness and designed for a maximum service flow of 4000 LPH. The MGSF shall be charged with pebbles, gravels, sand and anthracite with a total media quantity of 350 kg, the IRF shall be loaded with 100 litres of ISR resin, and the ACF shall contain pebbles, gravels and 100 kg activated carbon having iodine value ≥ 900; all filters shall be supplied complete with inlet/outlet manifolds, valves, fittings, piping and backwash arrangements with a minimum backwash duration of 20 minutes. The system shall also include one antiscalant chemical dosing package consisting of a 100-litre FRP chemical tank, metering pump of 0–5 LPH capacity, and complete accessories with mounting arrangement. Further, a packaged RO system of 1000 LPH capacity shall be provided on SS 304 skid, equipped with one 8" × 40" TFC/CPA membrane from approved makes such as DuPont Dow Water Solutions, Hydranautics or Hydramem, suitable for maximum feed TDS of 2500 ppm, and driven by a 2 HP multistage centrifugal high-pressure pump of make Lubi Pumps, KSB Limited or CRI Pumps. Complete interconnecting piping between raw water tank, pretreatment units, RO skid, UV system and treated water tank shall be executed in SS 304/UPVC as required, inclusive of all valves, fittings, supports and clamps, resulting in a fully integrated and operational treatment system.

FIRE FIGHTING , FIRE ALARM & PA SYSTEM

(a)Supplying, installation, testing and commissioning of electric driven terrace 10 HP pump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal as required. (c) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-12615: 2018. (d) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (e) Suitable cement concrete foundation duly plastered and with anti vibration pads. 900 lpm at 35 m Head (10 HP pump)

(a)Cost of Horizontal type, multistage, centrifugal, split casing pump with bronze impeller, stainless steel shaft,mechanical seal at a flow of 900 lpm at 35 m Head conforming to IS 1520. (b) Cost of SQ cage induction motor, TEFC, synchronous speed of 1500 RPM, having class-'F' insulation and protection class IP 55 as per IS-325. (c) Cost of MS base plate coupling, coupling guard,foundation bolts and anti vibration pads.

Supply, Erection of emergency Start / Stop Push Button station weather proof type for Booster pump panel at terrace level. The panel also shall compatible for auto start and manual stop for pumpset set on pressure loss basis.(Star delta)

3C x 10 sq.mm

2C x 1.5 sq.mm

Supply & Making end Termination with brass compression gland and aluminium lugs for PVC insulated and PVC sheathed cable of 1.1 kv grade (without cost of Cable)

3C x 10 sqmm

2C x 1.5 sq.mm

Supplying and installation following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers MS/GI SuspenderSupplying and installation following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers MS/GI Suspenders i/c base of suitable size MS/GI angle, bolts & nuts, painting suspenders, fastener etc as required.s i/c base of suitable size MS/GI angle,bolts & nuts, painting suspenders, fastener etc as required.

100 mm width X 50 mm depth X 1.6

Supply,Installation,Testing & Commissioning of Pressure gauge of 0-16 Kgf/sq.cm. range with cut-off bronze ball valves of suitable size with all accessories as per direction of Engineer-in-charge.

Supply,Installation,Testing & Commissioning of Pressure Switch with cut-off bronze ball valves with integral strainer & flare nut (mixed ends) of suitable size with all accessories as per direction of Engineer-in-charge.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 1239/Class -II of IS: 3589 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

100 mm dia

80 mm dia

25 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required

100 mm dia each butterfly valve

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 100 mm dia each non return valve valve

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 100 mm dia

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. Cost of 250mm dia air vessel withr release valve and 25mm dia gunmetalvalve for drainage.

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required . Single headed Gunmetal

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required. RRL Hose with male female gunmetal coupling

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. (a) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 (b) 20 mm nominal internal dia gun metal globe valve & nozzle. (c) Drum and brackets for fixing the equipmets on wall. (d) Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. swinging type hose reel complete with 19mm x 30m Thermolplastic hose Hose reel drum

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903,suitable for instantaneous connection to interconnect hose pipe coupling as required. gunmetel short branch pipe

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: two way gunmetal FBC connection

FIRE EXTINGUISHER

Providing ,fixing , testing and commissioning of Portable Carbon-di-oxide Gas Type Fire Extinguisher 4.5 Kgs, squeeze Grip,Controllable discharge mechanism with nozzle, bend, Hose and wall mounting bracket etc.The Can is made of Seamless Clinger and External Coating done by Spray Painting.The thickness shall not less than 4.5 mm made of Sheet metal.The Fire Extinguishers shall be ISI Approved as per IS 15683:2006.Vendor shall consider the suitable signages along with the extinguishers.

Providing ,fixing , testing and commissioning of Portable ABC powder type fire extinguisher 6 Kg capacity containing Mono Ammonium Phosphate Powder 50, Stored Pressure Type, fitted with Discharge hose, brackets etc., .The Internal Coating of Can shall be Epoxy Powder coating and External painted with Epoxy Polyester Powder coating.The thickness shall not less than 1.6 mm made of Sheet metal.The Fire Extinguishers shall be ISI Approved as per IS 15683:2006.Vendor shall consider the suitable signages along with the extinguishers.

Providing ,fixing , testing and commissioning of Portable K type fire extinguisher 9 Lt Capacity, Stored Pressure Type with Pressure Gauge, hose and brackets etc .The discharge Range shall be minimum of 6 mtrs.The Internal Coating of Can shall be Epoxy Powder coating and External painted with Epoxy Polyester Powder coating .The thickness shall not less than 2mm made of Sheet metal.The Fire Extinguishers shall be ISI Approved as per IS 15683:2006.Vendor shall consider the suitable signages along with the extinguishers.

Providing ,fixing , testing and commissioning of Fire buckets round bottom type enamel painted, white inside & Red out side and Letter "FIRE" in black out side and handle with mounting bracket.The buckets hall be filled with sand.

Providing ,fixing , testing and commissioning of Fire bucket stand fabricated by MS angles to install 2 Nos. of buckets.

SIGNAGES

Providing ,fixing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC Non-reflective self adhesive vinyle painted foam board, complete with mirror fasteners.

A sign shall read “IN CASE OF FIRE, USE STAIRS UNLESS INSTRUCTED OTHERWISE”. The lettering shall be at least 12.5 mm block letters in red and white background. Such lettering shall be properly spaced to provide good legibility. The sign shall be at least 250 mm x 300 mm, where the diagram is also incorporated in it and 62.5 mm x 250 mm where the diagram is omitted. In the latter case, the diagram sign shall be at least 200 mm x 300 mm. The sign shall be located directly above a call-button and squarely attached to the wall or partition. The top of the sign shall not be above 2 m from the floor level.

Fire exit signage at Each stairway and each elevator back shall be identified by an alphabetical letter. A sign indicating the letter of identification shall be posted and maintained at each elevator landing and on the side of the stairway door from which egress is to be made.The lettering on the sign shall be at least 75 mm high, of bold type and of contrasting colour from the background

A sign shall be posted and maintained within each stair enclosure on every floor, indicating the number of the floors.The numerals shall be of bold type and at least 75 mm high. The numerals and background shall be in contrasting colors. The sign shall be securely attached to the stair side of the door.

Stair Re-entry Signs sign shall be posted and maintained on each floor within each stairway and on the occupancy side of the stairway where required, indicating whether re-entry is provided into the building and the floor where such re-entry is provided.The lettering and numerals of the signs shall be at least 12.5 mm high of bold type. The lettering and background shall be of contrasting colours and the signs shall be securely attached approximately 1.5 m above the floor level.

PA SYSTEM

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP4 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following

FIRE ALARM

Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required. Heat Detectors of electronic Rate of Rise cum fixed tempreature (Dual Thermistor) type with mounting base complete with all connection etc.

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required. Smoke Detector with built in LED, mounting base complete with all connection etc.

Supplying, installation, testing & commissioning of manual call box of ABS type in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required. Manual call boxes of ABS Type in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in A.B.S. box with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. Fire alarm sounders (electronic) with facility to make announcement, mounted in A.B.S. Box with hinged cover plate & suitable for operation with amplifier i/c line matching ttransformer etc

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 4 Zone fire alarm control panel as per IS: 2189 with backlit LCD Display

Supplying, installation, testing & commissioning of addressable fire control module complete as required. Cost of control module

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required. Response indicator on surface/recessed MS Box having two LED's metallic covers complete with all connections etc.

Supplying, installation, testing & commissioning of fault isolator complete with base as required. Cost of fault isolator complete with base

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS/HFFR outer sheath complete as required. Cost of Fire alarm armoured FRLS cable 2 x 1.5 sqmm

Please Enable Macros to View BoQ information