PROVN OF CERTAIN SANCTIONED WORKS UNDER AGE B/R-II

Amount

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in any type of soil, complete all as specified & directed.

Excavation in trenches n. exc 1.50 m wide and n.exc 1.50m in depth for foundation and getting out in any type of soil, complete all as specified and directed.

Excavation over areas not exc. 1.5m deep in any type of soil and getting out, complete all as specified and as directed.

Excavation over areas exc. 1.5m deep and n. exc 3m deep in any type of soil and getting out, complete all as specified and as directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25cm, complete all as specified.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified.

Removing excavated material exc 250mtr but n.exc 500 mtr and depositing where directed.

M&L sand filling in floors or paving incl leveling watering and consolidation complete all as specified

Spreading & leveling in layers n.exc. 25cm thick, well ramming including watering as required

M&L Sand cushioning to underground cables complete all as specified in clause 19.75 of SSR Part-I laid before and after laying of cable, complete all as specified.

Hardcore of guage exc 63mm,Broken Stones or Boulders deposited, spread & leveled in layers n exc. 15 cm thick, watered & rammed to a true surface.

M&L PCC 1:4:8 (nominal mix), type D-2, using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete, complete all as specified & directed.

Precast cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate) set in cement mortar 1:4 as in slab, etc complete all as specified and directed.

M&L PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate in roof kerbs or mud stops, rounded or chamfered on edges, benching on chajjas , surface finished even and smooth without using extra cement complete all as specified & directed.

M&L Cement concrete type B-1 (1:2:4) (20 mm graded crushed stone aggregate) as in coping, bed plates and the like including weathering, slightly roundered or chamfered angles and throating, as directed including necessary form work and finishing complete all as specified.

M&L Cement concrete type C-1 (1:3:6) (20 mm graded crushed stone aggregate) for kerb stone etc all as specified.

Extra for forming fair finished drain or channel 30cm inner grith in cement concrete, using extra cement, including forms, moulds, mitred/stop ends etc complete all as specified and directed.

M&L concrete bed to drain pipes incl forming cadles in cement concrete 1:3:6 type C2 for 200 mm dia pipe complete all as specified and directed.

M&L PCC 1:4:8 type B1 using (20mm graded crushed aggregate) as in subbase and in foundation concrete complete all as spd and directed.

M&L Reinforced cement concrete M-25 ( Design mix) as in foundations including rafts, footings, foundations beams, plinth beams, bases for columns and basement slabs etc complete all as specified and directed.

M&L Reinforced cement concrete M-25 ( Design mix) as in columns, pillars, piers, posts and struts etc complete all as specified and directed.

M&L for reinforced cement concrete M-25 as in lintel beams, roof beams etc complete all as specified and directed.

M&L Reinforced cement concrete M-25 ( Design mix) as in Slabs supported on walls, beams and columns in floors roofs, landings, balconies, canopies, deck slabs, chajjas and in shelves all as specified and directed.

Reinforcement cement concrete M-25 ( Design mix) as in Chajja complete all as specified and directed.

RCC 1:2:4 type B1 (20mm graded aggregate) as in wall, retaining wall, basement wall, ballast wall and the like any thickness above topof footing including attached pilaster and buttresses etc complete all as specified and directed.

M&L Brick work with fly ash bricks old size, straight or curved on plan exc 6 mtr mean radius built in CM (1:6) all as spd and directed.

Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:4, complete all as specified.

M&L for brick work with sub class 'B' bricks old size straight or curved on plan to any radius in half brick thick built in cement mortar 1:4 all as specified.

M&L Brickwork with fly ash bricks, old size straight or curved on plan to any radius in half brick thick walls built in CM (1:4) and as directed.

M&L cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc,; and cutting chases for concealed water tubing or concealed conduit wiring etc., and making good, cutting not exc. 10cm girth in brick/stone walls, complete all as specified.

M&L for 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces, The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated fitted to chowkats all as specified and directed.

Soild PVC door frame wood grain color coated of size 50mm x 47mm made out of 5mm wood grain colour PVC sheet reinforced with MS Sqaure tube , supply and fixing in opening as per specification & drawing complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frames shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom railon either side and as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification & drawing complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, including flat rough finished surafaces of concrete complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns, and stanchions, square, rectangular or polygonal in shape, including flat rough finished surafaces of concrete complete all as specified and directed.

Formwork to sides and soffits of floor and roof beams, beams haunching, girders, bressummers, lintels and cantilever, shelves including supports over hangs etc rough finished surfaces of concrete ( flat ) complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs & similar items including edges rough finished surfaces of concrete ( flat ) complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar works, flat rough finished surafaces of concrete; not exceeding 200mm thick (horizontal or sloping) complete all as specified and as directed.

Formwork to faces of wall retaining walls, abutments,parapets and staircase railing and similar work including attached pillasters, buttresses etc vertical of to batter.

Formwork to edges of concrete flats, treads, , breaks in floors, openings in concrete walls, floors & roofs & sides of RCC/PCC bands in walls, horizontal or sloping, & similar work exc 20cm wide rough finished surfaces of concrete.

Formwork to edges of concrete flats, treads, , breaks in floors, window cills, concrete railings, openings in concrete walls, floors & roofs n exc 20cm wide & & sides of RCC/PCC bands in walls, horizontal or sloping, & similar work exc 10cm but exc 20cm wide rough finished surfaces of concrete.

M&L Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

S & F TMT bars 6mm to 8 mm dia and below cut to length bent to shape required, incl cranking , bending spirally for hoping for columns , hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

M&L Mild steel TMT bars 6 to 10mm dia ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, (as in stirrups) hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-310-O or Fe-410-O all as specified & directed.

S&F 100 mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts complete all as specified and directed.

S&F for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed complete all as specified and directed.

S&F 150 mm size aluminium alloy handles, febricated type extruded section, ISI marked complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in floor Overall length of cover plate 150mm

S & F Peg set of Six powder coated fixed with chromium plated brass screws and wooden and plastic cleats ( min wt 190 gms)

M&L Box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick M S sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire cloth and glass panes only shall be measured and paid seperately) with side hung shutters with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 150 mm long for each leaf and 10 mm square bar grills at spacing as shown on drg welded to FI frame work, including other fittings, hinges, handles, tarred hold fasts, PCC blocks etc all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F pressed steel frame made out of MS sheet 1.25mm thick of size 105x60 mm for doors/windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling of concrete 1:3:6 type C-0 (12.50 mm graded crushed stone aggregate) back of chowkhats and including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete.

M&L Steel rolling shutters ( thickness of laths 1mm thick ), with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete but gear operated type with bevel gear box and crank handle etc

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel 0.50 mm thk of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw as in roof complete all as spd .

S&F Prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridge /cladding to wall, fixed with self tapping screws as specified.

False ceiling of 9.5mm thick gypsum tiles (600x600mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or crack) fixed using T grid/Cross-T/Wall angle/level clip & suspenders of standard galvanised sections in a grid size of 600x600mm of manufacturer M/s Saint Gobain or equivalent of Armstong/Everest including taking down existing ceiling board & grid work etc of any type/pattern complete.

S&F steel work in tubular trusses and purlins including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St.-240, complete all as specified.

Erection and fixing only steel work in tubular trusses and purlins including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St.-240, complete all as specified.

S & F for Mild steel bolts , purpose made with hexagonal or square head one end and screwed the other, or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut exc 30 cm long diameter on neck in exc 12 but n.exc 20mm complete all as specified and directed.

M& L steel iron base plate plugs, bolts, and screws of Fe 410-W(Gde-E-250 Quality -A) complete all as specified and directed.

Bands, straps, supports or stays for rainwater, ventilating pipe, including bolts if required hooks (stay) heavy, for large gates; hook and pintle hinges : large hasps and staples; chains hand made sliding bolts clamps; hold fasts;wall tie hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters;knee piece inserts; two way and three way straps, plate washers and similar small article conforming to Fe-290 Gde E-165.

M&L 60 mm thick M-35 grade machine pressed precast concrete interlocking paver block any shape and size conforming to IS-15658-2006, with grey cement and no pigment, all as specified and as directed.

M&L for Cement concrete 1:3:6 type C-1 (using 20mm graded agg) as in plinth protection, 75 mm thick and finished even and smooth without using extra cement all as spd and directed.

Roughening surfaces of old concrete floor by picking,sweeping clean and washing down with water to remove dust etc and brusing neat cement slurry with 3.00 kg per sqm all as spd & directed.

M & L screed bed or bedding layers of mortars 15 mm thick in CM 1:4 for laying floor finishes.

M&L for 100 mm thk PCC 1:4:8 type D-2 as in subbase to flooring.

M&L 40mm thick PCC 1:2:4 type B-1(20 mm graded aggregate) in sub base,sub floors, floors and paving complete all as specified and directed.

M&L 20mm thick cement plaster in cement mortar 1:4 on concrete surface finished even and smooth using WPC liquid of make Dr. Fixit or STP as per manufacturer instruction @ 0.200 ltr in 50 Kg of cement (liquid water proofing compound shall be measured and paid separately ) complete all as specified and as directed .

M&L APP modified roof treatment over existing non-accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning existing surface properly. (b) Applying oil bound bitumen primer @ 0.30 liter/Sqm manufacture by the same agency as that of APP with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying not less than 3.6mm thick APP modified water proofing membrane weighing not less than 3.60 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Laying of membrane. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Top of membrane shall be provide with solar reflective bituminous aluminum paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane.

Supply only liquid water proofing compound.

M&L Cement concrete type C-1, 1:3:6 (using 20mm graded crushed stone aggregate) as in plinth protection 75mm thick laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight complete all as specified and as directed.

M&L for 100 mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring complete all as specified and as directed.

M&L 25 mm thick PCC ,type B-1(using 20mm graded crushed stone aggregate) as in flooring cmplete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed (joint free) in neat cement slurry and pointed in coloured cement laid over 15mm thick screed bed in CM (1:4) all as spd and directed.

M&L glazed ceramic coloured tiles in vertical surface 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match incl rendering 10mm thick in CM (1:4) and finished rough, complete all as spd & directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc over 15mm thick screed bed in CM 1:4, set and jointed (joint free) in neat cement slurry and pointed in coloured cement including dismantling of existing floor, hearth or wall tiling including cement mortar bedding all as spd & directed.

M&L for 10mm thick plaster in cement mortar 1:3 in fascia / edging / ceiling of Chajjas, roof projections, manholes, drinage, etc finished even and smooth without using extra cement mixed with water proofing compound. (Note: WPC shall be measured and paid seperately)

M&L Rendering 10mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

M&L Rendering 15mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:4) finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 05 mm thick cement plaster on faces of brick work or concrete surfaces in cement mortar (1:3) as in ceiling finished even and fair without using extra cement all as specified and directed.

Preparation of new plastered surfaces of wall and applying three coats of white wash, complete all as specified.

Preparation of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified.

Preparation of new plastered surface of external wall and chajjas and making the surface smooth with sand paper and priming the surface with alkali resistance primer paint for external surface, and applying two coat of cement base paint including curing complete all as specified & directed.

M&L two coats of distemper oil emulsion over a coat of primer after application average 2mm thick wall putty including preparation of new surfaces complete all as specified and directed.

M&L two coats of distemper oil emulsion over a coat of primer after application average 2mm thick wall putty including preparation of old surfaces complete all as specified and directed.

M&L two coats of synthetic enamel paint on old steel surfaces of any description, n.exc 10 Cms in width or girth, including preparation of surfaces, complete all as specified and directed.

M&L Preparation of new steel sufaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved shade over one coat of red oxide primer not otherwise described including rubbing out and cleaning rust on new steel surfaces Complete all as specified and as directed .

M&L two coats of synthetic enamel paint on new or untreated wooden surfaces of any description, not otherwise described over 10 cms width or girth including preparation and a coat of pink primer, complete all as specified.

M&L 3 mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead / glazing pins in squares size n.exc 0.5 sqm in each pane all as specified and directed.

S&F 15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc all as specified.

S&F 20mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc all as specified.

Stop valve concealed cast copper alloy (ISI Markd) fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure with capstan head screwed both ends for iron pipe 15mm bore dia, complete all as specified and directed.

S&F 15 mm size gun metal globe or gate valves with iron wheel head, screwed both endsfor iron pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butter fly handles screwed down screwed for iron pipe .

S&F 20 mm size gun metal globe or gate valves with iron wheel head, screwed both endsfor iron pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butter fly handles screwed down screwed for iron pipe .

Angular Stop valve cast copper alloy (ISI Marked) fancy type, chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe 15mm bore dia, complete all as specified and directed.

S&F Bib taps for 15 mm bore pipe, cast copper alloy fancy type chromium plated complete all as spd and directed.

S&F 15mm bore pillar cock fancy type, screwed down high pressure with or without letters hot or cold with long screwed shank and fly nuts screwed for iron pipe ISI marked complete all as specified & directed.

S& F CP Shower rose with or without swivel joints, any size,including fixing to steel pipe or union complete all as spd and directed.

S&F towel rail CP 600 mm long complete all as specified and directed.

S & F Vitreous china wash basin(Oval Shape), white flat back,size 550 x 400 mm including waste pipe , brackets and cutting for and pinning in ends of brackets or errecting stand and 32 mm dia PVC waste pipe including waste copling 32mm size full thread , all as spd and directed.

S&F Vitreous china wash down water closet pan (pedestal pattern), white, complete including supply and fixing to trap, Incl Supply and fixing of Plastic water closet seat, black, closed pattern with flat bottom, & cover & mild steel chromium plated or aluminized hinging devices.

S&F PVC flushing cistern 10 ltr capacity incl PVC connection inlet and and outlet connections,brackets,incl supply and fixing PVC flush pipe 32mm bore of polyethylene of low or high density complete including making necessary connections to water supply pipe line and jointing to WC all as specified and directed.

S&F Viterous china urinals, half stall type, incl CP coupling, waste pipe and all necessary fittings, complete incl providing and fixing plugs , bedding urinal against wall in CM 1:2 , securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F Jet Spray (with 1.50 mtr tube) fixed to EWC and Angular Stop Cock complete all as specified and directed.

M&L Rotational moulded polyethlene water storage tanks of capacity 1000 litres three layers (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete including 20mm dia ball brass valve high pressure with polythene float complete all as specified & directed.

Rotational moulded polyethlene water storage tanks of capacity 500 litres three layers (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete including 20mm dia ball brass valve high pressure with polythene float and dismantling of existing PVC tank of any capacity complete all as specified & directed.

S&F 100 mm bore sand cast iron soil waste and vent pipes ISI marked in any length with or without ears laid in floor with cement joints all as specified.

S&F 75 mm bore sand cast iron soil waste and vent pipes ISI marked in any length with or without ears laid in floor with cement joints all as specified.

S&F 75mm bore sand cast iron soil waste and vent pipes ISI marked in any length with or without ears fixed to walls with clamps and cement joints all as specified.

S&F 75mm dia CI bends (any radius) diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed .

S&F 75mm dia CI bends (any radius) diminishing pieces or tapers (larger bore measured).

S&F 100mm dia CI bends (any radius) diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed .

S&F Cast Iron Branch peices, Double (equal or unequal) ordinary or inverted (spigot or socket type), or with parrallel branches fitted with oval access doors of 100 mm bore dia complete , ISI Marked all as specified & directed.

S&F CI floor trap 75 mm with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 with CP grating with or without hole for waste pipe complete all as specified.

S&F cast iron cowl for 75 mm dia complete all as specified and as directed .

S&F Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof for 75 mm dia of pipe.

S&F cast iron Swan necks (or offsets) upto 152mm projection for 100 mm to 75 mm pipe complete all as specified and as directed .

Factory made RCC manhole cover with frame( for manhole iner opening 60 cm) complete all as spd and directed.

M&L 200 reinforced cement concrete pipes class NP2 with one collar per length of pipe complete all as specified and as directed.

Cutting into existing manholes for connecting new drains for ineternal dia of pipe 100mm dia and above, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required.

Construction of septic tank for 300 users (Brick construction with sub class 'B' bricks using old size bricks), earth work in any type of soil,Foundation in PCC1:2:4, Brick work in CM 1:4, RCC slab covers Incl RCC Precast manhole cover having 6 mm Plate embeded all around/ fibre reinforced cover with Angle Iron frame vent Shaft and Sludge chamber etc complete all as specified and shown on drawings No CEPZ/TD-013/13 Sheet 1/5 to 5/5 Dated 11.09.13.

M&L Construction of Soakage well 3.60 m dia and 4.50 m deep below (Brick construction with sub class 'B' bricks using old size bricks) inlet pipe level (depth from ground level to below the inlet pipe 45 cm) , earth work in any type of soil , foundation in PCC 1:3:6 , wells of Honey combed and Solid in M-25 Concrete, Incl Intercepting Chamber , screen Chamber Brick work in cement mortar , RCC cover slab in M-25/ filling with brick bats, complete all as specified and shown on drawings No CEPZ/TD-013/13 Sheet 1/5 to 5/5 Dated 11.09.13.

Taking down chowkhats of frames exc 1.50 sqm but n. exc 4.0 sqm with shutters (without taking off shutters from the frames) all as spd.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc) sheets in roof coverings

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc .

Dismantling structural steel work in tubular purlins including doors, gates but excluding framed trusses etc complete all as specified.

Taking down cement plaster on brick walls or stone walls any descrition etc including raking out joints, hacking for key, scrubbing down with water etc all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n. exc. 15cm thickness (below or above ground level) all as specified and as directed.

Taking down point wiring with aluminium/ copper conductor for light points/ light socket/ power socket on teakwood batten with clips including taking down switches, sockets, light fitting any type, holders, (batten type and pendent), ceiling rose, wooden boards, shades any type, main switches, distribution boards, any capacity and making good dismantled surfaces, complete all as specified.

M&L point wiring with 1.5 sqmm multi stranded copper conductor 1100 volts. grade FRLS PVC insulated unsheathed cable with proper colour coding drawn in including PVC concealed conduit /existing conduit of appropriate size but not less than 20mm dia with all accessories and FRLS PVC insulated 1.5 Sqmm multi standard unsheathed copper wire for continues earth, with inner, outer frame plates including metal flush shunken boxes with zinc oxide plated suitable size for mounting switches, sockets, fan regulators etc connecting earth dolley with PVC unsheathed flexiblke copper conductor green in color and making good to the disturbed surface of wall/floor and matching with existing specifications for the One light /fan/bell point controlled by one switch.

All as per Srl item No 133 above but one 3 pin socket outlet 5 Amps on independent board with separate switch 6 Amp one way.

All as per Srl item No 133 above but one 3 pin socket outlet 5 Amps on same board with separate switch 6 Amp one way.

All as per item No 133 above but with 2.5 sqmm multi stranded copper conductor 1100 volts grade FRLS PVC insulated sheathed cable with FRLS PVC 2.5 Sqmm multi standard insulated unsheathed copper wire for continues earth on independent board.

All as per item No 133 above but with 4 sqmm multi stranded copper conductor 1100 volts grade FRLS PVC insulated sheathed cable with FRLS PVC 4 Sqmm multi standard insulated unsheathed copper wire for continues earth on independent board.

Supply and Fixing the switch piano type flush button single pole 5 Amp , front operated.

Supply and Fixing socket outlet 2 in 1, 5 and 5 Amps combimed pin 15 Amp.

Supply and Fixing socket outlet 2 in 1, 5 and15 Amps combimed pin 15 Amp.

Supply and Fixing the switch piano type flush button single pole 15 Amp , front operated.

S&F ceiling rose PVC/polycarbonate, isolated body surface Bakelite 65mm dia three terminals.

S & F Lamp holder,PVC/polycarbonate type with back plate suitable for batten fittings, including 14W LED Lamp complete all as specified and directed.

Supply and fixing the bulk head light fitting LED type 10 watt complete with lamp and having IP-65protection and fixing on wall/ceiling complete with all accessories and including connecting up with ceiling rose by using PVC insulated and overall sheathed flexible copper conductor cable 3 core 0.50 Sq mm.

S & F in replacement LED batten alongwith LED T8 tubular lamp 20W Linear LED T8 tubular lamp with extruded aluminium/pc body and PC diffuser and inbuilt driver, 230 volts wall mounted complete with all accesssories internally pre wired and including connecting up with three core twisted flexible copper conductor cable of suitable size including taking down old unsv tubelight fitting any type.

S & F mirror light 07 watt LED type with all accessories including inbuilt lamp connecting electrically to ceiling rose using cord flexible 3core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm all as required.

S & F sheet metal enclosure with plug socket and MCB 20A SP and making connection with sub main wire with suitable size of thimbles including Cutting chases of suitable size on existing wall and making connection to the submain wire and making good to disturb surface of wall/floor with cement mortar and finishes to match existing surface including testing on connected load complete all as specified and directed.

Supply and Fixing exhaust fan AC single phase 230/240 volts of size 380mm sweep with loure of metalic body with grouting with nut bolts and making the suitable hole suitable for 380mm sweep exhaust fan by breaking the existing wall and making the plastering and matching with existing surface / specification and all as specified and directed.

Supply and Fixing exhaust fan AC single phase 230/240 volts of size 300mm sweep with loure of metalic body with grouting with nut bolts and making the suitable hole suitable for 300mm sweep exhaust fan by breaking the existing wall and making the plastering and matching with existing surface / specification and all as specified and directed.

S&F double door MCB DB made out of 18SWG CRCA steel sheets, Phosphates powder coated with copper bus bar, Earth stud, Din Rail, Polyamide Terminal Blocks for incoming and outgoing circuits, inbuilt loose wire box, Ground terminal blocks, duly pre-wired with thimble flame retardant copper conductors and poly layer for protection SP 240 volts 200 Amps rated bus bar 4 way double door open able complete, including taking out old unsv MCB DB any size/type.

S&F 6 to 32 A SP MCB single pole 240 V 10 KA .

S&F 32 Amp SPN MCB single pole 240 V 10 KA .

M&L for earthing complete with galvanised steel earth plate electrode size 600x600x6.0mm thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below ground levels with top edge of the earth plate not less than 1.5 mtr below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanised earth lead wire 4.0 mm dia means of bolts, nuts, check nuts and washers of galvanised steel and GI pipe light grade 20mm dia bore for watering funnel with wire mesh. CI cover with frame, PCC chamber pit with PCC 1:3:6 type C-2 excavation and earth work all as shown in electrical plate No 3 connected to earthing test point all as specified or indicated including testing on completion.

Supply and Install the electric water heater storage type 25 Ltr capacity 5 Star rated of ABS body vertical type glass lined of inner tank and heating element and having the wall mounting arrangement,thermostate,indicators and thermally insulated stainless steel tank of glass lined inside the tank and heating element with complete connection of water & testing and all as specified and directed.

M&L for tube , light grade galvanised with all fittings laid in trenches/through wall / under road or floor of 40 mm bore complete all as specified and as directed.

Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm, drilled and screwed including 3 nos. 8mm dia 25mm long hex head screw, complete all as specified.

Supply and fix Copper rod 12.5mm diameter and 2.5 metres length complete all as specified.

S & F FRLS PVC insulated Unsheathed single core heavy duty 10 Sqmm copper conductor in and including PVC casing and caping, fixed to surface with clamping arrangement on one side to calmp copper rod of 12.5mm dia and fixing other side to test point complete all as specified.

PVC insulated, armoured, heavy duty duty LT electric cable with stranded aluminium conductor rating 1100 volts grade of size 16 Sqmm 2 core laid in trenches or passing through fixed to walls including flexible pipe of suitable size with clamping arrangement or through GI pipe under floor/Road including dismantling existing service cable of any size complete all as specified. (Earth work, brick protection and sand cushioning shall be measured and paid for separately).

PVC insulated, armoured, heavy duty duty LT electric cable with stranded aluminium conductor rating 1100 volts grade of size 16 Sqmm 2 core laid in trenches or passing through fixed to walls including flexible pipe of suitable size with clamping arrangement or through GI pipe under floor/Road including dismantling existing service cable of any size complete all as specified. (Earth work, brick protection and sand cushioning shall be measured and paid for separately).

PVC insulated, armoured, heavy duty duty LT electric cable with stranded aluminium conductor rating 1100 volts grade of size 10 Sqmm 2 core laid in trenches or passing through pipes/ducts or fixed to walls/poles complete all as specified. (Earth work, brick protection and sand cushioning shall be measured and paid for separately).

S & F star rated ceiling fan of size 1200mm sweep with fan regulator, 230 volts (single phase) including provisioning of three core flexiable copper cord of size 23/0.0076 of required length from ceiling rose or connector to ceiling fan for connection, complete all as specified & directed.

S & F Fan regulator modular step type suitable for 1200/1400mm sweep ceiling fan hum free, 100W- 2 module including necessary connections complete all as spd and directed.

M & L for well burned bricks , laid flat ( old size) sub class B designation 75 for cable protection copmplete all as specifed and directed.

abrol enterprises

M/S INDIAN ELECTRICAL

M/S J N TRADERS