Special repairs to Bldg No. P-39, Provn of 04 x toilet block and 03 x bathroom and Provn of 50 x WHB at

M&L for brick work with sub class 'B' bricks using old size bricks (half brick thick) straight or curved on plan exc 6m mean radious built in CM 1:4 all as specified.

M&L for Reinforced cement concrete (Nominal mix) M-25 (20mm graded aggregate) Type-B1 as in Foundation including rafts ,plinth beams , footings for column etc

M&L for Use and waste of form work to sides and soffits of roof beams & lintels over 1.50 m clear span complete all as specified

S&F factory made 2nd class, hard wood, 35mm thick glazed and skeleton shutters, open rebated and prepared to received glass, gauge, etc ( without sash bars) edges of framing plain, chambered or rounded, fitted with cut and mitred beads for securing glass , etc but divided into squares with plain chamfered or rounded mirted and rebated sash bars any numbers sizes of members of shutters as specified and directed by Engineer-in -Charge

S &F factory made 2nd class hard wood Plain, framed, panelled shutters 35 mm thick (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new steel surfaces of any description over 10cm girth or width not otherwise described and applying two coat of synthetic enamel paint over red oxide primer all as specified and directed by Engineer-in-Charge.

M/L for glazed ceramic coloured tiles in vertical surface 450 x350 x 7mm thick set and jointed in neat cement slurry pointed in white or colour cement to match the colour,with 10 mm thick cement screed bed (1:4) complete all as specifed and directed by Eng-In-Charge.

w plastered surfaces of walls and applying two coats of oil bound distermper over a coat birla white putty complete all as specified and directed by Engr-in-Charge

M&L for water proofing treatment to sunken floors of kitchen, toilets, laboratories,bath and WC's etc shall be as under:-

(i) Application of Two component acrylic modified cementitious coating. (a) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement litance, existing coatings and achieve a gripping profile that is clean, dry and free from litanceand any other form of surface contamination. the installation instructions in manufacturer's published literature should be strictly compiled with, including but not limited to the following:- (b) Chipping out any visible cracks in ' V- Groove' pattern as applicable. Special attention on this part cleaning of cracks and then filling those cracks with SIKA latex SBR 100 putyy/ Dr Fixit 302 SBR latex/ perma latex SBR / FOSROC Nitibond SBR latex/ Asian Paints latex as required. Final cleaning of surface with power grinder, wire brush, hair brush and vaccum pressure if required. (c) Dampen all surfaces immediately ahead of application of Acrylic modified cemetitious coating of Sika Top seal - 107/brush Bond FOSROC/ Dr Fixit/ STP/ CICO. (d) While the surface is still damp from saturation (SSD), apply one coat of acrylic modified cementitious coating of Sika Top seal- 107/ Brush bond FOSROC/ Dr fixit / STP/ CICO of viscosity as per manufacturer's instructions. (e) Apply glass fabric sheet of Sika Fab 1 / FOSROC/ Dr Fixit/ STP while the first coat is wet. (f) Once touch dry apply second coat of Acrylic modified cementitious coating of Sika Top Seal- 107/ Brush bond FOSROC/ Dr FiXit/ STP/ CICO of viscosity as per manufacturer's instructions on the entire area. (g) Second coat shall be applied after 6-8 hrs of application of previous coat and in the direction right angle to the previous coat. (h) The waterproofing coating should be taken to a height minimu 300mm above the finished floor level on the vertical surface. (j) It is essential to cure acrylic modified cementitious coating immediately after application ( minimum 6-8 hrs drying) for a minimum of 3 to 54 days to ensure full cement hydration and to minimize cracking.

(k) A protection plaster ( 12-15 mm thick) in CM 1:3 admixed with appropriate integral water proofing compound has to be applied on the walls. (l) Providing and applying a protection screed of 50 mm thick 1:4 cement sand mortar admixed with Sika plastocrtete over the applied water proofing coating on horizontal surfaces. Admixutre for item( k&l) above : Sika Plastocrete Plus/ FOSROC/ Dr Fixit/ STP/ CICO confirming to IS 2645 (m) All the corners and joints should be pretreated with elastic waterproofing sealing tape with a woven bonding mesh on each surface and an elastic expansions zone in the centre of make Sika Seal Tape S/FOSROC/Dr Fixit/STP. (n) The membrane has to be protected in accordance with the manufacturer's recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer's recommendations. (o) waterproofing treatment has to be carried out through applicators authorised.(ii) All the joints of pipesand traps within sunken portion shall be selaed properly by Epoxy sealant. (iii) All CI traps in sunken slabs to be enclosed with PCC 1:1.5:3 (min 15cm) all - round. (iv) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40 mm stone aggregate) complete all as specified. (v) Providing drainage spout pipe GI 40mm dia bore light grade upto outside of outer wall ( Approx 450mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed. (vi) Providing 25mm thick cement concrete 1:2:4 type B-0 using 12.5 mm grade stone aggregate as in flooring for laying floor finish all as specified. Note :- Item (iv),(v) & (vi) above shall be measured and paid seprately.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt in 250mm complete all as specified and directed.

M&L for preparation of new wooden surface exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S & F steel window 1.25mm thick Box type ( primer coated) ERW hollow P section of size 60mm x 25mm single rebated comprises glazed Skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T- Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC ( 1:3:6) type C-1 Four Nos for each window) including following fitting welded to frame shutter: (a) Handles of Z Sec 20mm x 100mm long (b) stopper – 01 No per leaf (c) Cleat 55mm long of hollow square 15mm x 20mmx63mm welded to hinges – 01 No per leaf (d) Mild steel Pintal hinges of size 75mmx75mmx12mm-02 Nos per leaf (e) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawings. Note: Glass and painting shall be measured and paid separately under appropriate item (ii) Irrespective of whatever shown on drgs, MS gills shall be of 12mm dia MS square bar and paid separately. complete all as specified and directed.

S&F steel window 1.25mm thick Box type ( primer coated) ERW hollow P section of size 60mm x 25mm single rebated comprises gauged Skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T- Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC ( 1:3:6) type C-1 Four Nos for each window) including following fitting welded to frame shutter: (a) Mild Steel Hold Fast,150mm long of 12mm Square bar made to shape – 04 Nos per window (b) Handles of Z Sec 20mm x 100mm long (c) stopper – 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mmx63mm welded to hinges – 01 No per leaf (e) Mild steel Pintal hinges of size 75mmx75mmx12mm-02 Nos per leaf (f) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawings. Note: Wire mesh and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed.

S&F 3.00 mm thick Plain sheet glass, one side sheet glass is groundor obscured or frosted in squares n exc 0.5 sqm each pane and glazing with metal beads all as specified all as specified and directed by Eng-in-Charge

S/F 300mm MS ordinary rat rail rod pattern helical springs including roller and roller plate complete all as speicified complete all as specified and directed.

Taking down GI tubing & connection 15mm dia laid in floor / trenches or fixed to walls complete all as directed by Engineer-in-Charge.

S&F High density polyethylene pipes(H

DPE) ,15mm dia, of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Eng-In-Charge.

Taking down GI tubing & connection 20mm dia laid in floor / trenches or fixed to walls complete all as directed by Engineer-in-Charge.

S&F High density polyethylene pipes(HDPE) ,20mm dia, of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Eng-In-Charge.

S&F CP Glass corner shelf (set of three) including CP railing, radius 300mm fixed in repairs complete all as specified and directed by Eng-In-Charge.

S&F kitchen sink with drain board made of stainless steel 1mm thick sheet with plugs, washers and wastes including bedding in cement mortar including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F utensil rack stainless steel of size 750x600x250 mm fixed on walls with screws complete all as specified and directed by Eng-In-Charge

S&F in repair 25mm MS curtain rail powder coated with fixing brackets, stops, roller etc complete all as specified and directed by Eng-In-Charge

Cutting chases pinning in brick/stone/blocks masonary in making good to facings where required and pointing in CM (1:3) to ends or eges of steps, cills, sun shades, shelves, lintel etc and cutting chases for concealed water tubing or etc and making good complete all as specified and directed.

Taking down eaves gutters and rainwater pipes including all fittings as specified and directed.

Dismantling of cast iron pipe any diameter jointed with cement mortar or lead incl all fittings from wall or floors as specified and directed.

S&F 75 mm PVC (SWR) pipes in repair single socketed in any length with rubber ring joints fixed to walls complete all as directed by Engineer-in-Charge.

S&F 110 mm PVC (SWR) pipes in repair single socketed in any length with rubber ring joints fixed to walls complete all as directed by Engineer-in-Charge.

S&F 110 mm PVC (SWR) bend with complete all as directed by Engineer-in-Charge.

S&F 110 PVC (SWR) junction single,(single T) equal or unequal complete all as directed by Engineer-in-Charge.

Dismantiling water tank PVC 500 Ltrs and removing from site

Dismantling of brick tiles or terracing tiles laid bedded and pointed in cement mortar in single layer on roofs as directed by Engr-in-Charge

Demolition of mud in roof any thickness including plastering & leeping removed as directed by Engr-in-Charge

M&L for rendering 10mm thick cement mortar 1:3 on concrete surface even and smooth with waterproofing compound as directed by Engr-in-Charge

Supply only integral water proofing compound.

Preparation of newly plastered surface making surface completely dry and applying a coat of bitumen primer @ 0.40 ltr/sqm and after drying of primer apply APP modified water proofing membrane with non woven polyster reinforcement 3mm thick superior multipolymericweighing not less than 3kg/sqm with properties of high penetration and centre core consisting of 90 micron high molecular high density polyethylene (MHHDPE) film consisting of five layers with a coat of hot blown bitumen 85/25 @ 1.20 kg/sqm under and over the APP membrane laid with torching application to the surface complete and sealing the side as well as end laps (overlaps should not be less than 10 cm) complete all as specified and directed.

M&L for 40mm thick brick tiles laid on 15mm screed bed in cement mortar 1:3 with jointing and pointing in cement mortar (1:3) mixed with 5% crude oil by weight of cement all as directed.

All as per item no 124 above but except brick tiles complete all as specified and directed by Engineer-in-charge.

Material and labour for 75 mm thick Cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) as in PCC padding over roof slab complete all complete all as specified and as directed by the Engineer-in-Charge.

M&L cement concrete Type B0 1:2:4 (12.5mm graded aggregate) in roof kerbs, rounded or chamfered edges complete all as specified and directed by Engineer-in-charge.

Earthwork in excavation by mechanical means (hydraulic excavator) means over areas ( exceeding 30cm in depth, 1.5m in width as well as 10sqm on plan) including getting out and didposal of excavtaed earth lead upto 1.5m, as directed by Engineer-in-Charge

M & L for Cutting into existing manhole for connecting new drains and making good for 200 mm bore pipe and rendering, cutting out existing benching and forming branch (1/2 or 3/4 section) channel in plain cement concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregates, surface finished even and smooth and reforming benching as reqd.

One light point controlled by one, one way switch

One fan point controlled by one, one way switch

One socket outlet 3 Pin, 5 Amp on independent board

One socket outlet 3 Pin, 5 Amp on same board.

Taking down aluminium point wiring for light, fan, bell socket, power socket etc complete including fittings and fixtures removing from site and making good disturbed surfaces of walls, floors, etc complete all as directed by Engr-in-Charge

M&L for point wiring complete with 1.5 Sqmm single core multistranded copper conductor PVC(FRLSH) insulated cable in PVC concealed conduit of size 19/20 mm (ISI Marked) including PVC accessories (concealed in wall and surface in ceiling complete including cutting chasing & making good to disturbed surface etc including pressed steel terminal boxes (sunk in wall) with 3 mm thick plastic laminated sheet top cover with 1.5 Sqmm insulated un-sheathed PVC insulated copper conductor common earth and connecting to earth dolly for :-

One bell point controlled by one bell push

One light point controlled by two 2 -way switches

Ditto all per item no 02 above but with 2x2.5 Sq mm single core, multi-stranded copper conductor for 15A socket point on Independent board.

Ditto all per item no 02 above but with 2x4.0 Sq mm single core, multi-stranded copper conductor for geyser point on Independent board.

S&F switch piano flush type single pole one way 5 Amp (ISI Marked)

S&F Bell push flush type single pole one way 5 Amp (ISI Marked)

S&F switch piano flush type single pole two way 5 Amp.

S&F switch piano flush type single pole one way 15 Amp (ISI Marked)

M&L for ceiling rose, surface Bakelite 65 x 17.50 mm of three terminals PVC/Polycarbonate,isolated body

S&F socket out let 2 in 1, 3 pin 5 Amp flush type (ISI Marked) Make - Schnider/Siemens/Havells

S&F socket out let 2 in 1, 3 pin 15 Amp flush type (ISI Marked ) Make - Schnider/Siemens/Havells

Taking down old unserviceable lamp holder and S&F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including LED lamp 09W.

M&L for bell ding dong type, AC 230 Volts, single pole (ISI Marked)

Taking down Ceiling/exhaust fan ceiling cable end, dismantling blades and removing fan and Each blades to E/M store yard complete all as directed

S&F in replacement ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep, Min air delivery 210 CMM, service value 6.00 BEE with brushless direct current motor (BLDC) complete all as specified and directed. Note: (1) Rate for trasportaion to deposit at E/M storeyard to ceiling fan deemed to be incuded in this rate. Make : Orient electric automiser, Crompton Energion HS 1200, Havells efficiencia.

S&F Exhaust fans of 230 Volt 300 mm sweep copper wound bouble ball bearing heavy duty motor, metal blade with lovour complete including M&L for providing/cutting the round hole of required size in wall finishing the same supply and grounting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 23/.0076 copper c

able rubber insulated from ceiling rose to exhaust fan motor and writing MES No. with black synthetic enamel paint 2.0 cm high complete all as specirfied and directed.

S&F Exhaust fans of 230 Volt 250 mm sweep copper wound bouble ball bearing heavy duty motor, metal blade with lovour complete including M&L for providing/cutting the round hole of required size in wall finishing the same supply and grounting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 23/.0076 copper cable rubber insulated from ceiling rose to exhaust fan motor and writing MES No. with black synthetic enamel paint 2.0 cm high complete all as specirfied and directed.

Taking down energy meter of any capacity including connection and refixing the same after new wiring complete all as directed.

Supply, installation, testing and commissioning of 20 watt 4 feet long LED Batten housing made of extruded alluminium with milky white diffuser and inbuilt electronic driver system lumen output should be less than 2000 lumen with a CCT of 6000 K, power factor should be greater than 0.9 with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 all as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt, 220 volt AC decorative type with driver, holders,including LED lamp connecting up with three core flexible copper conductor of suitable size complete all as specified and directed.

Supply and fix LED Bldg security light fitting 35 W housing made out of die cast aluminum alloy with toughened glass, IP 65/66 protection having clamp for mounting on wall working on 240 V AC 50 Hz, 20 watts including fixed on wall with 02 Nos MS clamps and bracket made of 40 mm dia light grade GI pipe bend to shape. complete all as specified and as directed. Make : Wipro/Havells/Bajaj.

S&F LED decorative wall Lights 16/20 W 230 V complete all as directed at site. Make: Philips : Grace Wall light/ Philips/Crompton

M&L in replacement for sub main wiring with two runs of single core PVC insulated(FRLSH), unsheathed copper condutor, multi stranded cable of size 6.00 Sqmm 1100 volts grade drawn PVC concealed conduit of size 19/20 mm (ISI marked) including PVC accessories complete with one run of 6.00 Sqmm single core copper conductor multi-stranded PVC insulated(FRLSH), unsheathed cable as earth wire continuity conductor including cutting, chasing and making good to disturbed surface etc. complete all as specified and directed by Engineer-in-Charge. Note : Three run of 6.00 Sqmm cable and one run of PVC Conduit shall be measured & paid as one unit.)

Supply & fixing in replacement and Testing TP & N Vertical load line (VTPN) 4 way 415 Volts 50 Hz indoor type double door sheet metal enclosure IP-43 DB's IK-09 flush mounted with 250 Amp Copper busbar for each phase with two neutral bar & two earthbar and cable ties for cable management including Provision of MCCB 40 Amps,ICs=100%ICu, 16KA four pole as in comer including connecting terminal strip complete and SP MCBs as out going etc complete pre wired with suitable size copper conductor. The DB's shall hold type test certificate (CPRI) as per IEC 61439-3 complete all as specified and directed by Eng-in-charge including taking out old unserviceable DB and removing from site. (Note :- MCB/ MCCB shall be measured and paid separately)

Supply and fix Sheet steel factory made, powder coated MCB DB with bus bar 200Amps. Neutral link, Earth bar, double door SPN 8 way 230 volts all as directed. Make- Indoasian/Legrand/Havells

S & F Single pole and neutral enclosure with a two pin and earth with single pole MCB 20 Amp. Make :Havells/L&T/Legrand.

S&F MCB Single pole 240 volts 6-32 Amps, 10KA, B-series, Make - Havells/L&T, Legrand