GE 874/EWS-22/2021-22

Amount

Steel Furniture

Welding to steel frames of furniture articles such as chair CB steel with arms, chair CB steel without arms, chair verandah, table office clerk steel. Table office officers steel. Form with/without back, steel almirah, Locker Bed side steel, table dining ORs, charpoy D/B steel ply top etc, includes fixing of parts in proper position by preparing the old welded surfaces. Welding shall be done through gas welding n.exc 16 gauge length of welding exc 25mm to 30mm and Minimum width 6mm to 9mm in each point complete all as directed. Note : Total length 25mm to 30mm and width 6 mm to 9 mm will be counted as one point e.g. if there are five points of 5 mm long and 5mm to 6 mm wide each, it will be counted as one point). (Ref Dreg No. FD-75, 165, 256, 84, 1031, 1029, 1032, 77, 1008, , 69(M), CESZ/415)

REPAIR TO FORM WITH BACK AND FORM WITHOUT BACK (Ref Drg No. FD-77(M)/ FD-78(M) ) (a) Supply and fixing of well seasoned sheesham wood plank in single pieces free from knots and cracks size 1800x255x25mm and fixing the same with 09 Nos of GI Nuts and bolts as shown in drg duly French polished the wooden surface including preparation of surface all as directed by the Engineer in charge.

(b) Decription all as per srl item No 2(a) above by size 1800x150x19mm suitable for back, fixing with 02 each GI nuts and bolts on each side as shown on drg.

(c) Replacement of worn out MS conduit size 25 mm, 16 gauge made to shape as per drawing including welding and painting with two coat of synthetic enamel paint OG/Black over a coat of red oxide primer and preparation of surfcae complete as directed.

(d) S&F of rubber shoe best quality approved by Engr-in-Charge and GE to leg of Form with back and w/o back

REPAIR TO BOX KIT STEEL (FD -98(M)): Supply and fixing of the following components to box kit steel as per drg and as directed after removing the old one including welding complete where repaired. (a) Hasp and staple safety type 100mm long.

(b) MS butt hinges medium weight cold rolled of 75mm long.

(c) MS Handle 100mm long.

REPAIR TO CHAIR TUBULAR STEEL WITH AND WITHOUT ARMS (FD-75(M)) (a) S&F MS flat size 20mmx3mm thick 500mm long to chair CB steel with arms 02 Nos to each chair under seat joining both ends in each chair duly painted with synthetic enameled OG paint after applying two coat of primer all as directed by the Engr-in-charge

(b)Description All as per srl item No 4(a) above but size 420mm long to chair CB steel without arms.

(c) S&F of sheesham wood seat frame suitable for chair CB steel tubular with arms duly painted with two coats of synthetic enamel black paint over a coat of primer, woven with 2mm wide cane plastic half round and 3mm wide border shall be provided all around in true Godrej pattern.all as directed.

(d) Description All as per srl item No 4 (c) above but suitable for chair CB steel tubular without arms.

(e) S&F of sheesham wood back frame suitable for chair CB steel tubular with arms duly painted with two coats of synthetic enamel black paint over a coat of primer, woven with 2mm wide cane plastic half round and 3mm wide border shall be provided all around in true Godrej pattern all as directed.

(f) Description all as per srl item No 4(e) above but suitable for chair CB steel tubular without arms.

(g) S&F of arms to chair CB steel with arms made out of well seasoned sheesham wood duly painted with two coats of synthetic enamel black paint over a coat of primer complete all as directed.

(h) S&F of rubber shoe best quality approved by Engr-in-Charge and GE to leg of Chair Tubular Steel

REPAIR TO ALMIRAH STEEL LARGE/MEDIUM/SMALL WITH SHELVES AND ALMIRAH STEEL WITH MIRROR (DOUBLE SHUTTER) & LOCKER BED SIDE STEEL (FD-67(M)/FD-1031/FD-1032/FD-257/FD-CESZ-SK-415/05 and FD-1029) (a) Removing unserviceable shelves almirah large steel and providing new shelves made out of PBI sheet, 1mm thick cold rolled duly spray painted with synthetic enamel OG paint over a coat of red oxide primer after preparation of surface and fixing the same with MS clamps, nuts and bolts as shown on drg.

(b) All as per srl item No 5(a) above but for almirah small/medium steel.

(c) Removing of unserviceable locks, S&F of New GI Locks with brass lever of approved quality ISI marked having three ways device and double keys all as specified and directed

(d) S&F in replacement lock plate made of 3mm thick MS plate as per trade pattern all as directed

(e) S&F CP steel handle and to make the locking device in proper function as specified and shown on drg.

(f) S&F of legs (foot rest) of 18 gauge MS sheet wherever required to almirah large steel including welding as per drg after removing the old one and painted with two coats of synthetic enameled paint OG Colour over a coat of primer, all as directed.

(g) description all as per srl item No 5(f) above but to almirah medium/small steel.

(h) Description all as per srl item No 5(e) above but to almirah medium/small steel.

(j) Removing unserviceable moving rod of almirah large steel and supply and fixing new moving rod 8mm dia of required length as per drg including making it functional and applying two coat spray sythetic enamel paint OG Colour over a coat of primer, all as directed.

(k) Description all as per srl item No 5(h) above but suitable for almirah medium/small steel.

(l) Description all as per srl item No 5(h) above but suitable for almirah steel double shutter with mirror

(m) S&F Hasp and staple safety type 75x40x3mm thick to locker bedside steel.

(n) S&F MS butt hinges medium weight cold rolled of 75mm long to Almirah large/Small/medium/Locker bed side steel/Almirah double shutter with Mirror.

(o) S&F CP Handle 100mm long to Locker Bedside Steel.

(p) S & F New Looking Mirror Size 560mmx 300xx5mm thick suitable for Double door shutter steel Almirah. Make-Modiguard confirming to IS-2835 complete as shown on drg.

REPAIR TO TABLE DINING Ors (FD-165) (a) S&F new table top made out of MDF board commercial type ISI marked 18mm thick duly covered with aluminium sheet 22 gauge of required size and painting complete as shown on drg after removing the old one, all as directed.

(b) Replacement of worn out conduit MS size 25 mm 16 gauge wherever required and as directed including welding complete all as directed

(c) S&F of rubber shoe best quality approved by GE to leg of Table Dining OR

REPAIR TO TABLE OFFICE OFFICER STEEL: FD-1003/FD-84(M) (a) S&F new drawer of table office officer steel made out of 20 gauge MS sheet duly painted including two coats of synthetic enamel paint over a coat of primer after removing the old one all as shown on drg and as directed.

(b) S&F top of size 6'x3' made out of 18/19mm thick Prelaminated particle board as approved after removing the old one. PVC beading shall be provided all around all as directed by Engr-in-charge.

(c) S&F brass locks suitable for drawers of table office officer steel after removing the old one of approved quality. Make: Godrej, Seema, Victory or Manoj.

(d) Replacement of worn out conduit MS size 25 mm 16 gauge wherever required and as directed including welding complete.

(e) S&F of rubber shoe best quality approved by GE to leg of Table Office Officers Steel

(f) S&F of rubber/plastic drawer handle of best quality approved by Engr incharge/GE to Table Office Officers Steel

REPAIR TO TABLE OFFICE CLERK STEEL: FD-1004/84(M) : (a) S&F of new drawer of table office clerk steel made out of 20 gauge MS sheet including a coat of primer after removing the old one all as shown on drg and as directed after removing the old one.

(b) S&F top of size 4'x2' made out of 18/19mm thick Prelaminated Particle board as approved after removing the old one. PVC beading shall be provided all around all as directed by Engr - in -charge.

(c) S&F brass locks (ISI marked) suitable for drawers of table office ckerks steel after removing the old one of approved quality all as directed

(d) Replacement of worn out conduit MS size 25 mm 16 gauge wherever required and as directed including welding complete.

(e) S&F of rubber shoe best quality approved by GE to leg of Table Office Clerk Steel

(f) S&F of rubber/plastic drawer handle of best quality approved by Engr incharge/GE to Table Office Clerk Steel

REPAIR TO CHARPOY GI PIPE WITH NYLON NEWAR AND CHARPOY GI PIPE WITH PLYTOP (FD-220) (a) Replacement of unserviceable long rail by supplying new 32mm dia medium grade GI Pipe of 1980mm length duly threaded, conforming to IS-1239 part-I 1990.

(b) Replacement of unserviceable short rails made to shape and size from long rails obtained from 9 (a) above. (Note : Each long rail retrieved from 9(a) will be convered into two short rails and remaining scrap will be contractor's property)

(c) Replacement of unserviceable legs made to shape and size from short rails obtained from 9 (b) above. (Note : Each short rail retrieved from 10(b) will be convered into two legs and remaining scrap will be contractor's property)

(d) Replacing of UNSV check nuts 6mm thick after removing the old one.

(e) Replacement off UNSV/cracked 32mm dia 3 way GI elbow ISI marked duly approved

(f) Removing old unserviceable nylon newar of charpoy GI pipe, tightening of complete charpoy and provision of 12mm thick BWR plywood in one piece of approved brand on top of size 1980mm x 915mm fixed with 10 Nos 75mm x 5mm GI Nut & bolt with suitable washer through the GI Pipe of Charpoy by providing one MS flat size 25mmx900mmx5mm thick on the long rils duly black painted over a coat of red oxide to suport the ply as directed by the Engineer-in-charge

(g) Removing old unserviceable Plywood of charpoy GI pipe with plytop , tightening of complete charpoy and provision of 12mm thick BWR plywood in one piece of size 1980mm x 915mm fixed with 10 Nos 75mm x 5mm GI Nut & bolt with suitable washer through the GI Pipe of Charpoy by providing one MS flat size 25mmx900mmx5mm thick on the long rails duly black painted over a coat of red oxide to suport the ply as directed by the Engineer-in-charge of approved brand

REPAIR TO CHARPOY DOUBLE BUNK STEEL PLY TOP (FD No- CESZ/SK-47/05) (a) Replacement of unserviceable plywood size 1830x915x12mm one piece BWR grade as approved

PAINTING TO STEEL FURNITURE Spray Painting of complete area both externally and internally with two coats of synthetic enamel OG/Black/white/any other colour of paint of approved quality as directed by Engr-in-charge by removing dust/derusting, preparation of surface by applying putty wherever required to the following steel furniture items. Primer shall be provided before painting at places where denting/welding has been carried out. (a) Steel structure of form with back (FD-77)

(b) Steel Structure of form without back (FD-77).

(c) Box kit steel (FD-98(M)).

(d) Chair CB steel with arms (FD-75(M)).

(d) Chair CB steel without arms. (FD-75(M)).

(f) Almirah large steel with shelves (FD-351, 1031).

(g) Almirah small/medium steel with shelves (FD-350, 1032).

(h) Almirah steel double shutter with Mirror. (Drg CESZ-415).

(j) Locker Bed side steel. (FD-1029).

(k) Table Dining OR (FD-165).

(l) Table Office Officer Steel (FD-84, 1003).

(m) Table Office Clerk Steel (FD-84, 1003).

M/S SS SHAH WALI & CO

HAYAT TRADING CORPORATION

M/S ABDUL AHAD SHAH

Bidder Name

M/S ABDUL AHAD SHAH

HAYAT TRADING CORPORATION

M/S SS SHAH WALI & CO

M/S MIR AND CO