REPAIR/MAINT OF ROADS, SIDE FURNITURE IN OFFRS MD ACCN, VIP BLDGS, MESSES AND OTM AREA AND PBOR MD ACCN, AJMER LINE AND LANCER LINE I AND II UNDER THE AREA OF AGE B/R-I UNDER GE (ARMY) NO. 1 JODHPUR

Amount

M&L for machine cut Jodhpur edge stone of size 300mm x 100mm and length not exceeding 450mm laid dry as in 100mm thick edging of road including necessary excavation and demolition complete all as specified and directed

M&L for repair to pot holes not exceeding 30mm depth not exceeding 1.00 Sqm each including sweeping free from dust and mud or water, scoring sunken surfaces in road, etc., cutting around edges to at least 30mm in depth, making good by applying tack coat using paving bitumen VG-10 grade @ 5 kg per 10 Sqm, putting in premix asphaltic semi-dense concrete using 5.5% binder content by weight of total mix, filled up to the top level of existing road, well rammed (including supply of bitumen, premix and chippings) and compacted with power roller complete all as specified and directed.

M&L for preparing black top surfaces of roads by brushing with wire brush for removing cracked mud etc, sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc and applying evenly a tack coat with paving bitumen VG-10 grade at the rate of 5.0Kg per 10Sqm complete all as directed and specified.

M&L for bituminous premix semi dense asphaltic concrete 30mm consolidated thickness with 5.50% binder content by weight of total mix using paving bitumen VG-40 grade, mixed in computerized hot mix plant, laying with mechanical paver, rolled and compacted to required camber or gradient using 8 to 12 ton power roller complete all as directed and specified. Note:- (i) The mix design shall be got done from approved lab and got approved from GE before commencement of work. (ii) In the event of variation in the mix design in the percentage of binder content on minus side, the difference in quantity of binder content will be adjusted through supply only rate of Rs 42/- per kg for paving bitumen VG-40. However no plus adjustment shall be applicable if excess quantity of binder is used/approved in the execution of work under in this item

Scarifying or picking gravelled, macadam or bituminous macadam surface in area not exceeding 400sqm, not exceeding 50mm deep and removing where directed by Engr-In-Charge complete all as specified and directed

M&L for preparing unsurfaced WBM surfaces of roads by brushing with wire brush for removing cracked mud etc., sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc., and applying evenly a tack coat with paving bitumen VG-10 grade at the rate of 10 Kg per 10Sqm complete all as specified and directed..

M&L 150mm thick (compacted thickness) WBM, in two layers of 75mm thick (Compacted thickness) with coarse aggregates of grading 2 (63 to 40mm size), spread, rolled 8 to 10 tonne power roller and compacted to required camber and gradient complete all as specified and directed. Note:- The unit rate quoted is for two layers of WBM (laid, rolled and compacted to 75mm thick each) measured as one unit.

M&L for laying premixed bituminous macadam with 4.5% (by weight of total mix) binder content using paving bitumen of VG-40 grade rolled and compacted to required gradient and camber (consolidated thickness 75mm or less) using power roller of 8 to 12 tonne capacity complete all as specified and as directed.

M&L for preparing bituminous road surfaces and marking/painting lines, dashes, arrows, letters etc. on roads, pavements and the like not exceeding 10cm wide, 2.5mm thick with retro reflective Thermoplastic road marking Paint of approved colour, all as per BS-3262-1989 specifications, with 8% glass beads laid in 160 degree centigrade by special applicator machine complete all as per manufacturer's instructions including removing old paint complete all as specified and as directed.

S&F in repairs Solar powered road stud (cat eyes) of size 125mmx 125mm x 20-25mm (60mm shank) of self illuminating flashing type having 3 Nos LEDs for Bi-directional studs (flashing and not flickering) visibility minimum 1000 mtrs flashing rate 65-75 times per min with detachable N1-MH battery of 1.2V to give back up of at least 3-4 days from fully charged condition and it should be attached just before fixing and should not be accessible once installed, made of robust aluminium die-cast housing with embossed edges for protection against bullock cart iron wheels, having reflector strip in addition to LEDs stud from biome anchor water proof IP65 as per IS 12063-1987 category 2 tested toper from satisfactorily for minimum 100 hrs. under rapid Thermal cycling tests as per IEC 1215 between -40 to +80 degrees centigrade, weighting min 700 grams fixed as per manufactures instructions etc. including taking out old unserviceable one complete all as specified and directed.

S&F in repairs Cat eye, solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA stripes reflector of model No DA 972.0 fixed with and including MS studs of suitable size as per manufactures instructions complete all as specified and directed

S&F in repair 900mm dia reflective safety traffic mirror for road and side walk of stainless steel face. 0.90mm thick large radius of curvature for minimum distance distraction orange powder coated steel back and hood orange vinyl extrusion with 75mm clamp brackets for pole mounting complete all as specified and directed.

S&F metal tubular delineator made out of ABS round body fitted with 2 Nos of 65mm dia highly reflective reflectors made of PMMA and mounted on 45'50mm dia MS Pipe medium weight of 600mm height, duly powdered coated and thermoplastic elastomer 3 bands of green, red and yellow reflector, radium tape of 25mm wide strips with anti theft metal net for reflector protection, including embedded in PCC 1:2:4, type B1 using 20mm graded stone aggregate foundation of size 150 x 150 x 300mm complete all as specified and directed

S&F metal tubular solar delineator made out of ABS round body fitted with 2 Nos of 65mm dia highly reflective reflectors made of PMMA and mounted on 45'50mm dia MS Pipe medium weight of 600mm height, duly powdered coated and thermoplastic elastomer 3 bands of green, red and yellow reflector, radium tape of 25mm wide strips with anti theft metal net for reflector protection, including embedded in PCC 1:2:4, type B1 using 20mm graded stone aggregate foundation of size 150 x 150 x 300mm complete all as specified and directed

M&L for Moorum filling, laying, spread, including watering, rolling and consolidated to required gradient as in berms not exceeding 150mm thick complete all as specified and directed

S&F of stainless steel sign board with PVC/acrylic sheet of size 600mmx900mm, at the minimum height of 2.10mtr stainless steel posts of suitable dia including all writing aero sign etc., complete all as specified and as directed

ABHOG INFRASTRUCTURE PRIVATE LIMITED