BMSICL/Infra/09/2026 GR-01 Construction of 50 Bedded Integrated Ayush Hospital, Darbhanga

Internal B'Wall (Bung)

Earth work in excavation over areas (exceeding 30 cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m; disposal earth to be levelled and neatly dressed.

All kinds of soil

All kinds of soil

Depth not exceeding 1.5 m.

Depth exceeding 1.5 m but not exceeding 3 m

All kinds of soil

Beyond 30cm girth upto and including 60 cm girth

Beyond 60 cm girth upto and including 120 cm girth

Beyond 120 cm girth upto and including 240 cm girth

Above 240 cm girth

Compacting original ground supporting sub-grade Loosening of the ground upto a level of 500 mm below the sub -grade level, watered graded and compacted in layers to meet requirement of table 300-2 for sub grade construction.

Construction of subgrade and Earthen Shoulders Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2

Rolling with Vibratory Roller

450 mm dia piles

500 mm dia piles

600 mm dia piles

Making 25 cm (10") dia bore up to 4 mtr depth below ground with hand auger of approved quality in ordinary soil (vide classification of soil item A) true to plumb and without eccentri city in any stage of operation and disposal of the -excavated earth up to 50 mtr, Lead in eluding all lifts , all complete as per approved design and direction of E/l

63 CM (25) UNDER -REAM Making 63 cm (25) dia under ream at required with hand auger of approved quality in ordinary soil (vide classification of soil ifem - A) true to plumb and without iccentri city in my stage of opration and disposal of the excavated earth up to 50 mts lead in eluding all lifts , all complete as per approved design and direction of (E/l)

1:3:6 (1 Cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

1:3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

Foundations, footings, bases of columns, pile caps etc., for mass concrete.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Shelves (Cast in situ)

Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc. (in OHWT, Lift , Basement wall)

Columns, Pillars, Piers, Abutments, Post and struts

Stairs, (excluding landings) except spiral staircases.

Chimneys and shafts

Wheather shade, Chajja, corbels etc., including edges.

Edges of slabs and breaks in floors and walls :

Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards

Extra for shuttering in circular work (20% of respective centering and shuttering items)

Foundation

Walls

Roofs

Chimneys & shafts

TMT -500- 8mm dia .

TMT -500-10 mm dia.

TMT -500-12 mm dia.

TMT -500 -16 mm dia.

TMT -500 -20 mm dia.

TMT -500 -25 mm dia.

TMT -500 -32 mm dia.

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete

All work upto plinth level

Walls, columns, pillars, posts and struts

Beams, plinth beams, girder, bressumers, cantilevers, Suspended floors, lintels, roofs and staircase including spiral staircase, shelves etc.

Extra for R.C.C work above floor V level for each four floors or part thereof.

Add or deduct for providing richer or leaner mixes respectively at all floor levels.

Providing M-25 grade R.C.C. instead of M-20 grade R.C.C.

Providing M-30 grade R.C.C. instead of M-20 grade R.C.C.

Providing M-35 grade R.C.C. instead of M-25 grade R.C.C.

Brick work with bricks of class designation 100A in foundations and plinth in :

Cement mortar 1:6 (1 cement: 6 coarse sand )

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :(Weight-2.6kg,230mmx110mmx70mm)

Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work

Half brick Masonary Cement mortar 1.:4 (1 cement: 4 coarse sand ) - 125 mm th Brick work

Extra tor Brick work in superstructure above plinth level upto floor V cum

Extra for providing and placing in position 2 Nos, 6 mm dia , MS bars at every third course of half brick masonry (with F. P. S. bricks)

30 mm thick pre laminated PVC door shutters

Sliding windows

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Casement window

For fixed portion

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Door cum window

For fixed portion

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Sliding Doors (Top hung)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

With float glass panes of 5.50 mm thickness

In stringers, treads landings etc. of stair cases including use of required plates wherever required all complete.

In gratings, frames, guard bar, ladders, railings, bracket. gates & similar works.

Steel windows

fixed to steel windows by welding

fixed to openings/wooden frames with rawl plugs screws etc

Light shade using white cement

Orinary any Cement without any pigment

Light shade using white cement

Ordinary cement without any pigment

White Marble- Rajnagar plain white marble 18mm thick above 0.10 sqm upto 0.20 sqm

Black Zebra marble

Udaipur green marble

Pink Marble-

40 mm thick rough chisel dressed stone flooring over 20 mm (average) thick base including pointing with C.M 1:2 (1 cement :2 stone dust) with an admixture of pigment to match the shade of the stone with base 1:1:1 (1 lime : 1surkhi : coarse sand or 1:5 (1 cement : 5 coarse sand)

Red sand stone

white sand stone

1:4 (1 cement : 4 coarse sand)

1:6 (1 cement : 6 coarse sand)

1:4(1 cement: 4 coarse sand )

1:6 (1 cement: 6 coarse sand)

1:3 (1 cement : 3 coarse sand)

1:4 (1 cement : 4 coarse sand)

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams / litre, of approved brand and manufacture, including applying

Two coats

With ready mixed red oxide zinc chromate yellow primer of approved brand and manufacture on steel galvanized iron/steel works

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats whereever required to achieve even shade and colour

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.

With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams / litre

With ready mixed red oxide zinc chromate on steel iron works having VOC content less than 250 grams / litre

Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/litre, of approved brand required to achieve even shade and colour

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade :

New work (Two or more costs applied @ 1.43 ltr. / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm)

Providing and applying two coats of fire retardentpaint FR 881 un thined on cleaned wood/ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendation's of manufacturer to make the surface fire retardant.

Demolishing cement concrete including disposal of material within 50 metre lead:

Demolishing R.C.C. work including stacking of steel bars and disposal of unserviceable material withing 50 metres lead:

1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.

IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.

IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area.

IVth course of 400 micron thick PVC sheet (overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

With average thickness of 120mm and minimum thickness at Khurra as 65 mm.

3 mm thick

Providing and laying roof insulation with 40 mm thick impervious sparayed, closed cell free Rigid Polyurethane foam over deck insulation conforming to IS - 12432 Pt. III (density of foam being 40-45 kg /cum), over a coat of polyurethane primer applied @ 6-8 sqm per litre, laying 400 G polythene sheet ovre PUF spray and providing a wearing coourse of 40 mm thick cement screed 1:2: 4(1cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) in chequered rough finish, in panels of 2.5m 2.5m and embedding with 24 G wire netting and sealing the joints with polymerized mastic , all complete as per direction of Engineer-in-Charge.

Providing plinth protection 750 mm wide consisting of 12 mm thick cement plaster 1;6 with neat cement punning over 75 mm thick P.C.C. (1:3 :6) over brick flat soling over 75 mm thick local sand filling all complete

Providing & Fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately)

Coupler 110 mm

Band 110 mm bend

Shoe plain 110m Shoe

Along external wall where the apron is not provided using chemical imulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete.

Along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand ) to match the existing floor.

Providing high impact Polypropylene reinforced cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required.

Providing and fixing fibre cement high impact polypropylene reinforced roofing accessories in all colours with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers or with self drilling fastener and EPDM washer etc. complete:

Providing and fixing ridges and hips in non -asbestos fibre cement high impact polypropylene reinforced roofing with suitable fixing accessories or self drilling fastener and EPDM washer etc. complete.

Granular Sub-Base with Coarse Graded Material (Table:-400-2) Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor graded on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 (GSB grading-I Material)

Wet Mix Macadam Providing, Laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub-base/ base course on well prepared surface and compacting with vibratory roller to achieve the desired density. with vibratory roller

Prime Coat Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base (over WMM) including clearing of road surface and spraying primer at the rate of 0.60 kg / sqm using mechanical means.

Tack Coat Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous / granular surface cleaned with mechanical broom. (Providing Tack Coat on bituminous surface on full width of crust)

Bituminous Macadam Providing and laying bituminous macadam with 100-120 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction. For grading II (19mm nominal size)

Semi-Dense Bituminous Concrete Providing and laying Semi-Dense Bituminous Concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5% of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 508 complete in all respects (Providing and laying 25mm SDBC over full Crust width)For grading II(10mm nominal size)

Retro-Reflectorised Traffic Signs : -- Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC : 67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5mm thick supported on a mild steel angle iron post 75mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing

60cm x 45 cm rectangular

Direction and place Identification Signs upto 0.9 sqm Size Board : -- Providing and erecting direction and place identification retro-reflectorised sign as per IRC : 67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45x45x60 cm, below ground level as per approved drawing

Overhead Signs : -- Providing and erecting overhead signs with a corrosion resistant 2mm thick aluminium alloy sheet reflectorised with high intensity retro-reflective sheeting of encapsulated lense type with vertical and lateral clearance given in clause 802.20 and 802.30 and installed as per clause 802.70 over a designed support system of aluminium alloy or galvanised steel trestles and trusses of sections and type as per structural design requirements and approved plans

Painting Lines, Dashes, Arrows etc on Roads in Two Coats on New Work: -- Paintng lines, dashes, arrows etc on roads in two coats on new work with ready mixed road marking paint conforming to IS : 164 on bituminous surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control. Over 10 cm in width

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1cement : 3 coarse sand) including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required complete etc. as per direction of Engineer-in-Charge (lenght of finished kerb edging shall be measured for payment). Precast C.C. kerb stone shall be aproved by Engineer-in-Charge)

Painting Two Coats on New Concrete Surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces)

Providing and fixing at or near ground level factory made RCC pavement slab of M-30 grade of size 450x450x50 mm, including reinforcement with 6mm dia M.S. bars 4 nos. on each side, including setting in position in footpath to the required level and line over a bed of 20 mm average thick cement mortar 1:5 (1 cement : 5 coarse sand) having joints with same cement mortar and making gooves etc. complete as per direction of Engineer-in-charge.

Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design / shape laid in required colour and pattern over and including 50mm thick compacted bed of course sand, filling the joints with coarse and etc. all complete as per the direction of Engineer-in-Charge.

Plain / Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications.

Plastering with cement mortar 1:3 on brick work in sub -structure as per Technical Specifications

Local Sand Filing : -- Sand Filling in Foundation Trenches as per Drawing & Technical Specification

Earth work in excavation in foundation : -- Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and back filling with approved material. Foundation(Ordinary soil, Manual Means - upto 3 m depths)

Local Sand Filing : -- Sand Filling in Foundation Trenches as per Drawing & Technical Specification

Brick masonary in 1:3 cement mortar : -- Brick Masonry Work in Cement Mortar 1:3 in Foundation complete excluding Pointing and plastering, as per Drawing and Technical Specifications. (With fly ash bricks)

Plastering with cement mortar 1:3 on brick work in sub -structure as per Technical Specifications

Boundary pillar (Reinforced cement concrete M15 grade boundary pillars of standard design as perIRC:25-1967, fixed in position including finishing and lettering but excluding painting)

Construction of Median Construction of subgrade and Earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No.300-2)

Holes 1.2 m dia. and 1.2 m deep.

Holes 60 cm dia. and 60 cm deep.

Supplying and stacking of hard stone (for stone pitching) 22.5 cm thick at site

Dry stone pitching 22.5 cm thick laid in coursed and required profile with hammer dressed stones having no side less than 15cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete. (Payment for Stone to be made separately)

Kitchen sink with drain board

Kitchen sink without drain board

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing toilet paper holder :

Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.

100mm dia

75mm dia

For 100mm dia pipe

For 75mm dia pipe

32mm dia nominal bore market rate

50mm dia nominal bore market rate

15 mm dia nominal bore market rate

25 mm dia nominal bore market rate

15 mm nominal outer dia pipes

20mm nominal outer dia pipes

15mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40mm dia nominal bore

50mm dia nominal bore

External work

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

50mm dia nominal bore

65mm dia nominal bore

80mm dia nominal bore

15mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40mm dia nominal bore

50mm dia nominal bore

65mm dia nominal bore

80mm dia nominal bore

25mm dia nominal bore

65mm dia nominal bore

80mm dia nominal bore

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

100 mm nominal bore

150 mm nominal bore

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

20 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50mm nominal bore

65mm nominal bore

80mm nominal bore

With common burnt clay F.P.S.(non modular) bricks of class designation 100 A

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks ofclass designation 7.5

80 mm dia

100 mm dia

80 mm dia nominal bore

100 mm dia nominal bore

150 mm dia nominal bore

100 mm dia Ductile Iron Class K-7 pipes

150 mm dia Ductile Iron Class K-7 pipes

200 mm dia Ductile Iron Class K-7 pipes

100 mm dia Ductile Iron Class K-7 pipes

150 mm dia Ductile Iron Class K-7 pipes

All kind of soil

Pipes, cables etc, exceeding 300mm dia but not exceeding 600 mm dia

All kind of soil

All kind of soil

100 mm diameter

150 mm diameter

200 mm diameter

250 mm diameter

300 mm diameter

Providing and laying cement concrete 1:5:10 ( 1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) alround stoneware/RCC pipes including in bed for pipes to be laid in trenches as per standard details.

100 mm diameter

150 mm diameter

200 mm diameter

250 mm diameter

200 mm diameter

250 mm diameter

300 mm diameter

180x150 mm size P type

150mm dia RCC pipe

300mm dia RCC Pipe

450mm dia RCC Pipe

500 mm dia RCC Pipe

600 mm dia RCC Pipe

700 mm dia RCC Pipe

800 mm dia RCC Pipe

900 mm dia RCC Pipe

1100 mm dia RCC Pipe

1200 mm dia RCC Pipe

With comman burnt clay F.P.S. (non modular) bricks of class designation 7.5 (For Storm water)

With sewer bricks conforming to IS : 4885 (For Sewer)

With comman burnt clay F.P.S. (non modular) bricks of class designation 7.5

With sewer bricks conforming to IS : 4885

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming to IS : 4885

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming IS : 4885

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming to IS : 4885

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming IS : 4885

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

With Sewer bricks conforming to IS : 4885

With common burnt clay F.P.S. (non modular) bricks of class designation 100A

With Sewer bricks conforming IS : 4885

For pipes 100 to 250 mm diameter

With comman burnt clay F.P.S. (non modular) Bricks of class designation 7.5

300 mm dia.

400 mm dia.

100 mm nominal size dia.

200 mm nominal size dia.

100 mm nominal size dia.

200 mm nominal size dia.

100 mm nominal size dia.

200 mm nominal size dia.

All types of soil.

Metre

200 mm nominal size dia having minimum wall thickness 5.40 mm

200 mm nominal size dia.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing stiff pendent with 100 mm long, 20 mm dia X 1.6 mm thick steel conduit, aluminium cast back plate and brass holder complete, including wiring the down rod with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and paint

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required.

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

Supplying and making straight through cable jointing with heat shrinkable jointing kit complete with all accessories including ferrules suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

Item code

Extra for sliding door Gear for Top hung sliding doors

Specificaiton : providing & fixing structural Glazing (NCL Seccolor System) fabricated from cold roll formed sections made of prepainted (Base steel as per IS 513 'D' quality galvanized as per IS 277 with zinc of 120 gm/sqmtr.) with total coated thickness of 0.8 mm for verticals and total coated thickness of 0.6 mm thick G.I. sections are to be used as stiffners inside the PPS section mm for horizontals. The glass holding section made of 304 grade stainless steel of 0.6 as per the design requirement. Design calculations are to be made to suit wind pressure as given in IS 875 coated sections should be with primer coat of epoxy primer of 5-7 micron thick, finish painted with apolyster paint of 12-16 mycrons thick and backs coated with alkyd backer of 5-7 mycron. The section are to be of 33x 58 mm for vertical and horizontal, and section for reinforcement should be of 31x55 mm G.I. glass holding section should be of 37.5 x 37 x .8 mm for top and bottom grids in between should be of 37.5x18x.8 mm.

Preparation of surface by cleaning with the steel wire brush etc.

fixing 12.5 mm / 75 mm PVC Nozel in whole surface @ 1 Nozel per metre and grouting by compressure grouting machine.

After 24 hours, applying 1st coat water proofing chemical (Tecforce Part I & II or Epoxy Hardener) in whole surface.

After 24 hours of the 1st coat, applying 2nd coat. Applying chemicals :

Providing well burnt brick bats or Jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1:10) all complete as per building specification and direction of E/I.

Plantation of trees & Shrubs/ creeps.

Layout of all the buildings road etc in MLA & MLC Parisar by total station and periphery.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.

Providing & Fixing CP brass central hole wash basin mixer (table mounted) without popup waste with 450mm long braided hoses & brass nuts casted spout complete including cutting and making good wherever required.

Providing & Fixing CP Brass 115mm long Shower Arm with wall flange and pressure adjustable Shower Rose complete with all accessories as required and making good the walls wherever required.

Providing and fixing cast brass Clean Out plug with suitable insert keys for opening, male threaded joint with G.I. socket lead caulked to soil pipe/waste pipe of C.I. and C.I.(LA) pipe as required complete

Providing and fixing spun cast iron soil, waste and vent pipe including all fittings (plain or door) e.g. bends, junction, cowls, offsets, access pieces, jointing with refined pig lead of 25 mm deep drip seal joints including cutting chase or holes in walls and floors and making good where required.

150mm dia

Providing and fixing G.I floor drain consisting of 100 x 50mm G.I elbow, complete as per instructions.

Providing and fixing 125 mm dia, 1 mm thick Stainless steel grating with frame for floor traps or drains of required pattern including cutting and making good the floors complete.

Providing and fixing 100mm dia G.I. inlet fitting consisting of 100mm dia main G.I pipe with multiple G.I. sockets (Inlets) of required diameter welded to it (as per site requirement) and fixing the same to C.I trap and setting in cement concrete, complete as per instructions of the Engineer in charge.

Providing, fixing, testing & commisioning of uPVC pipes, conforming to IS 4985 class 3 (6 kg/cm2) including injection moulded fittings, jointing with solvent cement, cutting and making good the floors and walls and jointing to trap/waste pipe complete of outer dia.

Providing and fixing thermal insulation tubing for hot water pipes (exposed/chases/burried locations), over pipes of following nominal bores and thickness including all required accessories, protection as per manufacturer's recommendations, complete in al respect.

Providing and fixing mechanical motorised valve with float type sensors with control panel and sensors to open valve when water level is low in tanks and to close when water level is high in water tanks complete.

Providing, fixing , testing & commissioning of motorised butterfly valve (with by pass line) with float type sensors suitable for 240 volts with working pressure rating of not less than 5 kg/cm2 with control panel and sensors to open valve when water level is low in tanks and to close when water level is high in water tanks including necessary cables, conduits, upto junction box, pipe, butter fly / ball valves etc., complete.

40 mm dia

Providing and fixing mechanical motorised valve with float type sensors with control panel and sensors to open valve when water level is low in tanks and to close when water level is high in water tanks complete.

SOLAR WATER HEATING SYSTEM 200 LPD. FOR TYPE- BC

Solar Flat Plate collector of Type "B" having collector area should be min. 2 Sq, Mtr. (Collectror should be BIS & MNRE approved)

Solar hot water storage tank capacity of 200 liter made up of SS-304L insulated 55 mm puf insulation covered with pre- coated GI sheet.

Inter-connected of collectors & heat exchanger through hose pipe, hose pipe have withstand temprature capacity upto 80 degree C.

Temprature dial type from 0 to 100 degree C.

Electric heater 2 KW (ISI mark) with thermostate.

Ball Valve size 20/25/32 NB or as per vendor shop drawing.

NRV size 20/25/32 NB or as per vendor shop drawing.

CI Y-Strainer 20/25/32 NB or as per vendor shop drawing.

Civil work for grouting of the system.

Supply, Installation, Testing & Commissioning of 750 LPD ETC based Solar water heating System comprising of min 90 numbers of evacuated tubes, internal piping, insulated hot water storage tank, valves on inlet & outlet, Y strainer, temperature gauge. Details of each item mentioned below:

Solar collectors industrial Type of 70 tubes each as per tube details given below:- - Outer diameter: 47 mm (+/-1mm) - Inner Diameter: 37 mm (+/-1mm) - Wall thickness: 1.5 mm (+/-0.2mm) - Bend Degree: 4/1000 - Vacuum Degree: 5x10-3 Pa - Heal loss coefficient (K value): <0.90 Watt/ M2 0C 550 nos.

Supply, Installation, Testing & Commissioning Solar hot water storage tank capacity of 750 liter made up of SS-304L thickness 2mm with 100 mm glass wool insulation covered with chicken mesh and 22 SWG aluminum cladding.

Supply, Installation, Testing & Commissioning Inter-connected G.I. B-Class system piping size 32, 25 & 20 mm with fittings, insulated with 50 mm glasswool/rockwool insulation covered with chicken mesh & 26SWG Aluminum cladding to connect the collectors with hot water storage tank.

Supply, Installation & testing Temperature Gauge.

Supply, Installation & testing Ball Valve size 32 NB.

Supply, Installation & testing NRV size 32 NB.

Supply, Installation & testing CI Y-Strainer 32 NB.

M.S. angle stand for cold water tank to maintain 6Ft. Height.

Supply, Installation, Testing & Commissioning Monoblock Pump of 1/2 H.P. to feed cold water to 'Solar Cold Water Tank' from 'Overhead Storage Tank'

Automatic Control System to maintain water level in 'Solar Cold Water Tank'

Civil work for grouting of the system

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W/RCC. Pipes including bed concrete as per standard design:

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 4.5m, but not exceeding 6.0m.

Extra for providing & fixing 600 x 600 mm B 125 DI recessed type cover with frame, load rating as per EN124 : CDR - 1001, fixed in cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering shuttering all complete.

Deduction for SFRC Cover and frame (heavy duty HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592

Pipes, cables etc, exceeding 600mm dia but not exceeding 1000 mm dia.

Pipes, cables etc, exceeding 1000mm dia but not exceeding 1500 mm dia.

450 mm diameter

500 mm diameter

600 mm diameter

700 mm diameter

800 mm diameter

900 mm diameter

1100 mm diameter

1200 mm diameter

1400 mm diameter

1600 mm diameter

1400 mm dia RCC Pipe

1500 mm dia RCC Pipe

Supply,Installation, testing & Commissioning of suitable capacity and type of submersible pump set capable to discharge 20,000 ltrs. per hour of clean filtered water from a 250 mm x 150 mm deep tubewell at a total head of 30 meter, complete with control panel,24 metres of suitable size G.I. column pipe, bend, gate valve nipple supporting clamp, 30 metres of neoprene cable etc. complete as required.

SEWAGE TREATMENT PLANT ( 70 KLD) (MLA)

Control Panel for Sewage Treatment Plant

In-Line, multisage, centrifugal pumps with CI casing, SS-304 impeller and SS-316 shaft, CI base & head TEFC motor (with mechanical seal)

Variable Frequency Drive, External Pump mounted or wall mounted microprocessor PID controller and frequency inverter integrated in a single body or as separate components with pressure sensor transmitter minimum two lined LCD display, diodes to indicate pump ready, pump running and fault and capable to communicate with other controllers protocall through RS485 port. System should be capable to compensate for frictional losses at lower flows. All alarms should be displayed in the controller. System should be equiped with dry running protection

Complete (Skid mounted/wall mounted/floor mounted) electrical control panel comprising of all accessories such as PLCs, pressure switches, pressure transducers, control wiring and any other necessary imports etc. (list to be provided by the vendor)

Composite FRP pressure tank (with LDPE single piece jointless inner shell) fitted with precharged interchangeable bladder made of EPU suitable for direct contact with drinking water with necessary flanges, gaskets, base and inlet/outlet nozzle etc., nozzle with air/gas charging valve at top, safety valve, pressure gauge etc., The vessel shall be designed for operating pressure 7.5 kg/cm2, test pressure 12 kg/cm2 Capacity 750 Ltrs.

Set of accessories such as pressure switches, pressure transducers, inter connecting power and control cabling etc. complete

Accessories like pressure gauge, MS base frame (Synthetic enamel painted over a coat of primer)

Power box equipped with fuses or isolators or circuit breakers as required.

Capacity: 220 LPM (Each)

Cut out pressure : 5.0 kg/cm2

Cut in pressure : 4.0 kg/cm2

Mover : Electric Motor

HP - 5.0 (Approx.) or as required.

Quantity : 2 Nos. (1 W + 1 SB)

Capacity: 230 LPM (Each)

Cut out pressure : 5.0 kg/cm2

Cut in pressure : 4.0 kg/cm2

Mover : Electric Motor

HP - 5.0 (Approx.) or as required.

Quantity : 2 Nos. (1 W + 1 SB)

Complete piping 100mm dia common delivery upto 5m as per enclosed tentative layout. (The pipe should be preferably CI LA/heavy duty G.I) -- 1 Set

80mm dia sluice valve.- 2 Nos

80 mm dia reflux valve.- 2 Nos

Necessary cables from pump set to control panel (position of panel marked in enclosed layout in plant room).- 1 Set

Electrical switch panel having all necessary accessories & safety devices of standard specifications. (Panels with sump pumps near each sump as per site conditions). - 1 No.

Automatic built-up water level controller with necessary length of cable upto control panel.

150mm dia

100mm dia

80mm dia

65mm dia

50mm dia

40mm dia

150mm dia

100mm dia

80mm dia

65mm dia

50mm dia

150mm dia

100mm dia

80mm dia

65mm dia

50mm dia

150mm dia

100mm dia

80mm dia

65mm dia

65mm dia nominal bore.

80mm dia nominal bore.

100mm dia nominal bore.

150mm dia nominal bore.

40mm dia

50mm dia

50mm nominal bore

65mm nominal bore

80mm nominal bore

100mm nominal bore

150mm nominal bore

Panel - A

One incoming main isolation MCCB of required rating.

Fully taped aluminum bus bar of required capacity in a separate bus bar chamber.

Isolation switch units with MCCB of required rating, for all Hydro-pneumatic pump control panels, each unit as per details below

Fully automatic DOL/STAR DELTA starter with push button and ON/OFF indicating lights for each unit for following requirements:

Rotary switches for auto/manual ON/OFF operations for each unit.

Panel type ammeter 100mm square. One for each motors with appropriate range.

Neon phases indicating lights on the incoming mains.

Single phase preventor for each motor.

CT Operated Relay

All internal wiring colour coded from incoming mains to various switchgear, starter, meter, indicating lamp and bus bar. All the cable entry to the panel shall be from the top.

Panel - B - TO BE INSTALLED IN STP

One incoming main isolation MCCB of required rating.

Fully taped aluminum bus bar of required capacity in a separate bus bar chamber.

Isolation switch units with MCCB of required rating, for all Hydro-pneumatic pump control panels, each unit as per details below

Fully automatic DOL/STAR DELTA starter with push button and ON/OFF indicating lights for each unit for following requirements:

Rotary switches for auto/manual ON/OFF operations for each unit.

Panel type ammeter 100mm square. One for each motors with appropriate range.

Neon phases indicating lights on the incoming mains.

Single phase preventor for each motor.

CT Operated Relay

All internal wiring colour coded from incoming mains to various switchgear, starter, meter, indicating lamp and bus bar. All the cable entry to the panel shall be from the top.

Electronic water level controller working on magnetic type sensing probes.

Electronic minimum 5-level indicator with magnetic type sensing probes.

Arrangement of alternate switching mechanism for operational and standby pumps.

For Water level indicators with following details:

Underground tanks

Overhead tanks

For water level controllers with electronic sensing probe complete in all respect for following functions.

Control cable 6 core 1.5 mm2

Control cable 2 core 1.5 mm2

Power cable 3 core 6 mm2

Power cable 3 core 10 mm2

Power cable 3 core 16 mm2

Power cable 3 core 25 mm2

Power cable 3 core 70 mm2

Power cable 3 core 95 mm2

300mm wide x 40 x 2 mm

150mm wide x 40 x 2 mm

65 mm dia.

50 mm dia.

40 mm dia.

80mm dia

100mm dia

40mm dia

50mm dia

65mm dia

Filter Feed Pumps (P-1)

Domestic Water Transfer Pumps to OHT (P-2)

Flushing Water Transfer Pumps to OHT (P-3)

Garden Irrigation Pumps (P-4)

(Solid handiling capacity 12mm)

For chlorination of raw water

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

50 mm dia.

65 mm dia

80 mm dia

100 mm dia

150 mm dia

50 mm dia.

65 mm dia

80 mm dia

100 mm dia

150 mm dia

50 mm dia.

65 mm dia

80 mm dia

100 mm dia

150 mm dia

50 mm dia.

65 mm dia

80 mm dia

100 mm dia

150 mm dia

100 mm dia

Electrical Control Panels

Supporting rigid steel frame work.

Cubicle type, 2 mm thick CRCA sheet steel enclosed

Complete with interconnections and distribution bus bars.

Proper bonding to earth

Painting/lettering on switches and control panels, the location they serve, providing on each panel its circuit diagram.

All panel shall have provision for the following :

Padlocking of panel doors.

Padlocking of MCCB's handles in 'OFF' position

Providing cable clamps/supports within panels cable alley.

TPN MCCB shall means 3 pole MCCB with separate neutral link of adequate size.

All MCB's shall be minimum 10KA breaking capacity.

The breaking capacity of MCCB's are mentioned panel wise. All MCCB's shall be provided with static releases and setting plugs.

All motor feeders MCCB's shall be of motor duty.

Rubber mats shall be provided in front of all panels and shall be provided at the back where they are accessible from the back as per IS 5424-1969

Control panels shall be painted with light grey paint shade No. 631 of IS - 5

Degree of protection for following type of distribution panel enclosure shall be as per IS 13947-1993

IP 42 for indoor panels

IP 55 for outdoor panels

All MCCB shall be provided with operating mechanism for door interlock.

Minimum bus bar cross section shall be required for following fault level.

50x6 mm Aluminum for 20KA. 1 Sec.

Current density of Aluminium shall be 1 Sq.mm for 1 amps fir rated current of bus bars.

GI flat earth bus shall be provided through out the length of each panel.

MCC for submersible drainage pumps and tubewells to be supplied by the pumps manufacturers for complete compatibility.

Panel No. 1 for water Supply Pumps in Plumbing Plant Room

250 amps TP/TPN MCCB with following accessories:

1 set Phase indicating light with toggle switches through 415, primary by 2amps MCB's.

Spare MCCB's for starters of the following capacity :

All MCCBs shall be of 35 KA breaking capacity and suitable for motor duty application.

Electrical Control Panels

Supporting rigid steel frame work.

Cubicle type, 2 mm thick CRCA sheet steel enclosed

Complete with interconnections and distribution bus bars.

Proper bonding to earth

Painting/lettering on switches and control panels, the location they serve, providing on each panel its circuit diagram.

All panel shall have provision for the following :

Padlocking of panel doors.

Padlocking of MCCB's handles in 'OFF' position

Providing cable clamps/supports within panels cable alley.

TPN MCCB shall means 3 pole MCCB with separate neutral link of adequate size.

All MCB's shall be minimum 10KA breaking capacity.

The breaking capacity of MCCB's are mentioned panel wise. All MCCB's shall be provided with static releases and setting plugs.

All motor feeders MCCB's shall be of motor duty.

Rubber mats shall be provided in front of all panels and shall be provided at the back where they are accessible from the back as per IS 5424-1969

Control panels shall be painted with light grey paint shade No. 631 of IS - 5

Degree of protection for following type of distribution panel enclosure shall be as per IS 13947-1993

IP 42 for indoor panels

IP 55 for outdoor panels

All MCCB shall be provided with operating mechanism for door interlock.

Minimum bus bar cross section shall be required for following fault level.

50x6 mm Aluminum for 20KA. 1 Sec.

Current density of Aluminium shall be 1 Sq.mm for 1 amps fir rated current of bus bars.

GI flat earth bus shall be provided through out the length of each panel.

MCC for submersible drainage pumps and tubewells to be supplied by the pumps manufacturers for complete compatibility.

Control cable for liquid level controllers. 2 core 2.5 mm2

Power cable 3 core 4 mm2

Power cable 3 core 6 mm2

Power cable 3 core 10 mm2

25 mm dia.

Low voltage liquid level controller with stainless steel probes and PVC shroud, wiring from connector box on top of sump to probes of required length with audible alarm to sound in the control room. (Number of probes as required for function of each controller).

Water level indicator with LED display. For all OHT & UGT and spares.

300 mm wide

150mm wide (for vertical drops)

SEWAGE TREATMENT PLANT ( 2 x 120 KLD)

Control Panel for Sewage Treatment Plant

Filter Feed Pumps (P-1)

Vertical, inline multistage centrifugal pumping set with stainless steel SS-304 stage casing and SS-304 impellers with stainless steel SS-316L shaft as per IEC standards and GJL250 cast iron suction & discharge casing, connected to TEFC ventilated induction motor of 2 pole, 2900rpm, suitable for 400/440 volts, 3 phase, 50 Hz AC supply.

Pressure vessel of non corrosive FRP composite construction lined with NSF and/or FDA listed material, like high density polyethylene with fully replaceable polyurethane. Air cell burst pressure of minimum of 5 times the vessel operating pressure and cycle tested for 2,50,000 cycles.

Pump mounted or panel mounted microprocessor PID controller and variable frequency drive (VFD) integrated in a single body or as separate components with pressure sensor transmitter minimum two lined LCD display, diodes to indicate pump ready, pump running and fault and capable to communicate with other controllers following MODBUS-RTU or BACNET Class-2 protocol through RS485 port. System should be capable to compensate for frictional losses at lower flows. All alarms should be displayed in the controller. System should be equipped with dry running protection.

Pressure switches sensor type fitted with micro switch and having maximum pressure and differential scale should confirming BS-6134 standards and IP55 protection class.

Ball valves to be used should be hot pressed brass OT-58 with stainless steel ball and PTFE seal and O-Ring. NRVs to be used should be with Springs and O-Ring arrangement.

Complete set including all necessary suction and delivery valves and accessories, with the system to be skid-mounted on a common base frame and the following shall be the working duty.

(Solid handiling capacity 12mm)

For chlorination of raw water

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

50 mm dia.

65 mm dia

80 mm dia

100 mm dia

150 mm dia

50 mm dia.

65 mm dia

80 mm dia

100 mm dia

150 mm dia

50 mm dia.

65 mm dia

80 mm dia

100 mm dia

150 mm dia

50 mm dia.

65 mm dia

80 mm dia

100 mm dia

150 mm dia

100 mm dia

Electrical Control Panels

Padlocking of panel doors.

Padlocking of MCCB's handles in 'OFF' position

IP 42 for indoor panels

IP 55 for outdoor panels

50x6 mm Aluminum for 20KA. 1 Sec.

Panel No. 1 for water Supply Pumps in Plumbing Plant Room

250 amps TP/TPN MCCB with following accessories:

1 set Phase indicating light with toggle switches through 415, primary by 2amps MCB's.

Spare MCCB's for starters of the following capacity :

All MCCBs shall be of 35 KA breaking capacity and suitable for motor duty application.

(Vendor should be responsible for operational of system as per requirement).

Water level indicator with LED display. For all OHT & UGT and spares.

Filter Feed Pumps (P-1)

Domestic Water Transfer Pumps to OHT (P-2)

Flushing Water Transfer Pumps to OHT (P-3)

Garden Irrigation Pumps (P-4)

(Solid handiling capacity 12mm)

For chlorination of raw water

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

50 mm dia.

65 mm dia

80 mm dia

100 mm dia

150 mm dia

50 mm dia.

65 mm dia

80 mm dia

100 mm dia

150 mm dia

50 mm dia.

65 mm dia

80 mm dia

100 mm dia

150 mm dia

50 mm dia.

65 mm dia

80 mm dia

100 mm dia

150 mm dia

100 mm dia

Electrical Control Panels

Supporting rigid steel frame work.

Cubicle type, 2 mm thick CRCA sheet steel enclosed

Complete with interconnections and distribution bus bars.

Proper bonding to earth

Painting/lettering on switches and control panels, the location they serve, providing on each panel its circuit diagram.

All panel shall have provision for the following :

Padlocking of panel doors.

Padlocking of MCCB's handles in 'OFF' position

Providing cable clamps/supports within panels cable alley.

TPN MCCB shall means 3 pole MCCB with separate neutral link of adequate size.

All MCB's shall be minimum 10KA breaking capacity.

The breaking capacity of MCCB's are mentioned panel wise. All MCCB's shall be provided with static releases and setting plugs.

All motor feeders MCCB's shall be of motor duty.

Rubber mats shall be provided in front of all panels and shall be provided at the back where they are accessible from the back as per IS 5424-1969

Control panels shall be painted with light grey paint shade No. 631 of IS - 5

Degree of protection for following type of distribution panel enclosure shall be as per IS 13947-1993

IP 42 for indoor panels

IP 55 for outdoor panels

All MCCB shall be provided with operating mechanism for door interlock.

Minimum bus bar cross section shall be required for following fault level.

50x6 mm Aluminum for 20KA. 1 Sec.

Current density of Aluminium shall be 1 Sq.mm for 1 amps fir rated current of bus bars.

GI flat earth bus shall be provided through out the length of each panel.

MCC for submersible drainage pumps and tubewells to be supplied by the pumps manufacturers for complete compatibility.

Panel No. 1 for water Supply Pumps in Plumbing Plant Room

250 amps TP/TPN MCCB with following accessories:

1 set Phase indicating light with toggle switches through 415, primary by 2amps MCB's.

Spare MCCB's for starters of the following capacity :

All MCCBs shall be of 35 KA breaking capacity and suitable for motor duty application.

(Vendor should be responsible for operational of system as per requirement).

Water level indicator with LED display. For all OHT & UGT and spares.

Primary point for 6/16 amps switched socket outlet with (2 x 4 sqmm +1 x 2.5 sqmm ) copper conductor.

Same as item above but secondary point looped with primary point with ( 2 x 2.5 sqmm +1 x 1.5 sqmm) copper conductor.

Primary point controlled by one MCB.

Same as item above but Secondary point. i.e. Points to be looped with Primary point.

3 Nos. 63 amps TPN MCCB's of 25 KA service breaking capacity.

2 Nos. 40 amps DP MCB of 10 KA service breaking capacity

2 Nos. 63 amps TPN MCCB's of 25 KA service breaking capacity.

1 No. 40 amps DP MCB of 10 KA service breaking capacity

2000 VA (30 minutes backup)

3000 VA (30 minutes backup)

1000 VA (30 minutes backup)

Design, Fabrication, supply & erection of totally enclosed wall mounted semi recessed Sheet Steel meter box having approximate dimensions 750mm x 650mm x 215mm as per Architect's G.A.Drawing incorporating (i) incoming 1 no 63Amps 30kA 4 pole MCCB, (ii) outgoing 2 nos 40A 4 pole MCB & 1no 32A DP MCB, complete with interconnections as required.

Design, Fabrication, supply & erection of totally enclosed wall mounted semi recessed Sheet Steel meter box having approximate dimensions 750mm x 650mm x 215mm as per Architect's G.A.Drawing incorporating (i) incoming 1 no 63Amps 30kA 4 pole MCCB, (ii) outgoing 2 nos 40A 4 pole MCB & 1no 32A DP MCB, suitable space for installation of a 3phase 4 wire direct acting energy meter complete with interconnections as required.

1200 mm sweep A.C.ceiling fan complete with double ball bearing fan motor, blades, canopies and standard down rod as required.( Havells/ SS 390)

1 x 36Watts semi decorative Patty (Philips cat. No. MIROLTA Slim 36W HF or similar equivalent reputed make)

Supplying of following electric ceiling fan (capacitor type ) complete with down rod, canopies, hanging shackle, blades and speed regulator suitable for use on 230/240 volts.

Supply of bulk head fitting of coast Al. body suitably painted white inside ang grey out side, complete with heat resisitant type glass shade qesket, BC 1 amp holder suitable for 100 watt incardencant 1 amp & wire guard with locking arrengement etc.

250 mm dia.A.C. exhaust fan (Havells Model No.Ventil Air DX) or approved equivalent

36 watts fluorescent Tube

300 mm dia.A.C. exhaust fan (Havells Model No.Ventil Air DS-metal type) or approved equivalent

400 mm sweep A.C. wall fan

Decorative Wall Bracket suitable for 23W CFL Lamp (Havells Model : ARISTO Code: LHJE01106499) or equivalent approved make.

Decorative Ceiling light (Havells CROWN Cat no. LHDC74122670) complete with electronic ballast suitable for 22 watts circular fluorescent lamp, complete with lamp.

18W CFL Lamp (Philips)

SUPPLY OF EQUIPMENT

11 KV SWITCHGEAR COMPARTMENT

11 KV/433V TRANSFORMER COMPARTMENT

LT/CAPACITOR COMPARTMENT

3.5 x 300 sq. mm

3.5 x 240 sq. mm

3.5 x 185 sq. mm

3.5 x 150 sq. mm

3.5 x 120 sq. mm

3.5 x 95 sq. mm

3.5 x 70 sq. mm

3.5 x 35 sq. mm

4 x 25 sq. mm

3.5 x 35 sq. mm (Normal feeder pillar to plot)

4 x 25 sq. mm (DG feeder pillar to plot)

11 KV, 3C x 240 Sq. mm XLPE Aluminium cable.

LED 60 W Aesthetic Design street light fixture in high pressure die cast aluminium body with anti corrosion resistant glass cover with gasket to make it IP65. (Make: Legero Cat. No. Ledra-LOD 890)

4 x 6 sq. mm.

The DG set in sound attenuated enclosure shall be mounted on a fabricated rigid common base frame with resilient anti-vibration mountings including associated foundation/masonary work to provide 90% vibration isolation efficiency. The DG Set shall include all accessories, fittings, instruments etc complete as per specifications and as required. DG set design temp. will be 50 deg C. Fuel tank will be located inside Sound proof Enclosure.

Engine with all auxiliaries coupled with Alternator complete with AVR & accessories

Starting Battery, Battery cable, engine driven battery charging , alternator, including stand-alone mains powered battery float charger complete with relays, controls and indicators

The extended exhaust piping of 125 mm to collect & expel exhaust gases from engine cylinders, for the DG set, including turbo chargers, flexible connectors, 50 mm thick rock wool lagging with chicken mesh and 24 gauge aluminium cladding, elbows, horizontal / vertical pipe supports, thimble with spray shield / rain cap etc., as per standards / CPCB norms.

Acoustic housing suitable for thermal and noise level insulation as per relvevant code of practices. It shall be ensured that dB level as per relevant class shall be 75 dB at a distance of 1m from the equipment.

250 MM (NB) MS ERW pipe

200 MM (NB) MS ERW pipe

125 MM (NB) MS ERW pipe

Insulation of silencer (750 KVA)

Insulation of silencer (500 KVA)

Insulation of silencer (250 KVA)

Insulation of silencer (200 KVA)

DG PANEL-1

Supply, installation, testing & commissioning of single headed, Stainless Steel ISI marked oblique pattern hydrant landing valve with 80 mm dia flanged inlet and 63 mm dia instantaneous type female outlet complete with plastic cap and GI chain, twist release type plug and all accessories as per IS:5290-1983 (Type 'A').

Providing, fixing and testing of First-Aid fire hose reels wall mounting swinging type, fitted with of heavy duty mild steel construction with CI brackets, 25 mm dia. ball valve and 20 mm dia. x 36m long high pressure Hose Reel tubing as per IS:12585 with stainless steel shut-off nozzle having 5 mm dia. orifice. The hose reel shall strictly confirm to IS:884-1985.

Providing and placing in proper position controlled percolating (CP) Hose ISI marked (IS:8423) 63 mm dia x 15 m long complete with instantaneous type Stainless Steel 63 mm dia, ISI marked male & female couplings (IS:903) bound and riveted to hose pipe with copper rivets and 1.5 mm copper wire.

Providing and placing in proper position Non-percolating flexible hose (RRL type-'A') ISI marked (IS:636) 63 mm dia x 15 m long complete with instantaneous type stainless steel 63 mm dia. IS marked male and female couplings (IS:903) bound and riveted to hose pipe with copper rivets and 1.5 mm copper wire.

Providing and placing in proper position Stainless Steel 63mm dia short size branch pipes with 20 mm dia nozzles with 63mm instantaneous coupling ISI marked (IS:903).

Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete.

Providing and fixing fully glazed MS fully welded construction double leaf door shutter for fire hydrant station fabricated from MS 50x50x6 mm angle iron frame, fixed to wall and hinged MS 40x40x5 mm angle iron door shutter with required MS sash bars for glazing complete with locking arrangements, stove enamelled fire red finish with 'FIRE HYDRANT' written in front.

Approximate size 2100x1200x600 mm.

Providing and fixing Weather proof hose cabinets for yard hydrant fabricated from 16 g MS sheet with full glass door and locking arrangement, suitable to accommodate one hydrant valve, 2 nos.15m long hose, 1 No branch pipe and one fireman's axe. The cabinet shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required. (Approx 0.75mx0.6 mx 0.25 m).

Providing and fixing stainless steel fire brigade connection consisting of 63 mm dia instantaneous type male coupling with built-in check valves and 150 mm dia. flanged outlet complete with bolts, nuts and rubber insertions as required as per IS:904-1983.

Four way

Providing and fixing Stainless Steel Fire brigade suction hose coupling (Draw-out Connection) with nut for female coupling as per IS:902-1974 complete with 100 mm dia. GI suction pipe and 100 mm dia. 1 No. CI foot valve flanged (to be connected to static water tank).

Providing and fixing MS cabinet (to enclose above Draw-out/Fire brigade inlet connections) fabricated from 16g sheet with full front glass door and locking arrangement duly painted with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade and suitably mounted on a raised masonry platform as required (Approx.0.6 m x 0.6 m x 0.45 m).

Providing and fixing pressure gauges with isolation cocks and chrome plated copper pipes as hydrant station to read pressure from 0-20 kg/cm2 complete and of dial dia 150 mm

Providing and fixing Air cushion tank (air-vessel) 250 mm dia.x1.0 m high with dished top, made of minimum 6 mm thick MS pipe/plate complete with 25 mm dia. brass air valve (ball valve, pressure gauge type), 25 mm dia brass stop cock, nipple, tees, B46 elbow, pipe and all accessories as required including fixing brackets.

Supply, installation, testing & commissioning of mild steel pipe (IS:1239 Part-I) heavy class including cutting, threading, welding etc. bends, elbows reducers, clamps, hangers etc. including cutting holes in brick or RCC walls/slabs and making good the same complete including the cost of structural work for supports fabricated from standard sections of required sizes and thickness e.g. MS rods, angles channels, slotted angle, etc., cutting to sizes, drilling welding fixing to insert plates, including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade including all steel work. Note : Pipes upto 40 mm dia shall be threaded joints, above 40mm shall be welded joints.

100 mm dia

50 mm dia

Supply, installation, testing & commissioning of mild steel black pipe (IS:1239/IS:3589) heavy class including cutting, screwing, welding etc. complete with fitting viz. tees elbow, bends, flanges, reducers etc. including providing anti-corrosive treatment (coating and wrapping) with 4 mm thick tape and holiday test check as per IS:10221, 50mm sand filling around the pipe complete as required. Note : Pipes upto 40 mm dia shall be threaded joints, above 40mm shall be welded joints.

Supply, installation, testing & commissioning of Slim seal wafer type non-return valves (PN 16) complete with matching flanges, rubber insertion, nuts, bolts and washer etc. of following sizes.

150 mm dia

Supply, installation, testing & commissioning of Slim seal butterfly valves B 190 class (PN 16) complete with matching flanges, rubber insertion, nuts, bolts and washer etc. of following sizes.

15 mm dia. quartzoid bulb type GM sprinkler head suitable to operate at 680C (UL/FM/LOC listed/approved)

Providing and fixing 450x450x150 mm MS cabinet having full glass front door and locking arrangement with suitable shelves for keeping 40 spare sprinklers of pendent type & 15 spare sprinklers of side wall type sprinklers operating of 680C corresponding spanner of each type properly fixed in the cabinet painting with enamel paint of approved make and shade to the approval of engineer.

Providing, fixing, testing and commissiong of Slim seal butterfly valves B190 class (PN 16) complete with matching flanges rubber insertion, nuts, bolts and washer etc. of following sizes

Providing, fixing, testing and commissiong of electrically operated flow indicating switches with threaded connection for a minimum flow of 90 lpm for indicating water flow in sprinkler branch line on each floor including wiring from FS to panel with necessary junction box installed in accessible place.

On 150mm dia line

Providing, fixing, testing & commissioning of annunciater Panel for flow control switches, providing Audio/visual Indication of actuation of Automatic sprinkler system for each zone complete as per specifications. The panel should have interface for connection to complete controlled building management system. The panel should have :

10 zones (8 working and 2 spare)

Providing, fixing and testing CI 150 mm dia. isolation control valve assembly comprising of vertical wet alarm valve, including the cost of 150 mm dia butterfly valve, hydraulic alarm motor & gong, 15 mm dia. test valve, 50 mm dia. drain valve and all necessary trimming connections including 2 nos. pressure gauges as per manufacturer's catalogue (UL/FM/LPC/TAC listed/approved).

Providing, fixing, jointing and testing of mild steel black pipe (IS: 1239 Part-1) heavy class including cutting, welding/ screwing etc. and providing all fittings viz. flanges, bends, tees, elbow, reducers etc. including the cost of structural work for supports fabricated from standard sections (of required size and thickness) e.g. MS rods, angles channels, slotted angle, etc., cutting to sizes, drilling welding fixing to insert plates, including painting over a coat of primer, cutting holes and chases in brick or RCC walls/slabs and making good the same to the approval of engineer/consultant complete including painting with one coat of primer and two or more coats of enamel paint of approved make and shade including steel work. Note : Pipes upto 40 mm dia shall be threaded joints, above 40mm shall be welded joints.

Providing and fixing MS conduit of 16 SWG ISI marked (15:9537-1981, Part-11) complete with all fittings viz. tees, bends, junction boxes, clamps/supports etc. To be concealed in slabs/brick work as required or surface laid. (Exact quantities will be measured as per site conditions)

Providing and laying in MS conduit FRLS insulated ISI marked copper control cable in existing conduit (IS:694) from individual flow switches from basement ceiling to annunciation panel installed in fire control room including sleeves cable clips, supports for horizontal runs etc. complete of size (Exact quantities will be measured as per site conditions).

Providing and fixing 25 mm dia inspecting & testing assembly with gunmetal isolation valve, gunmetal sight glass, bypass valve & connected to drain line complete (excluding the cost of drain pipe).

SUPPLY, ERECTION, TESTING & COMMISSIONING OF Electric driven fire (Terrace) pump of capacity 900 LPM 55 mtr. Head with 15 H.P. TEFC motor at 2900 r.p.m. complete with coupling, coupling guard, base plate, anti vibration pad, foundation etc. (1 Working + 1 Stand by)

SUPPLY, ERECTION, TESTING & COMMISSIONING OF Cubical type floor mounted fire pumps i.e. Electric terrace pumps (Fire) control Panel fabricated from 16 Swg MS sheet duly painted with stove enameled finish of approved shade as per given in specification..

Providing and fixing Pressure gauge with isolation cock suitable with ‘U’ tube for maximum pressure of 7 Kg/cm2. (0-14 Kg./cm2; dial size:100 mm dia.)

Providing and fixing PVC insulated armoured cable 11 Kv grade aluminium conductor on surface as required

Providing, fixing, jointing and testing of mild steel black pipe (IS: 1239 Part-1) heavy class including cutting, welding/ screwing etc. and providing all fittings viz. flanges, bends, tees, elbow, reducers etc. including the cost of structural work for supports fabricated from standard sections (of required size and thickness) e.g. MS rods, angles channels, slotted angle, etc., cutting to sizes, drilling welding fixing to insert plates, including painting over a coat of primer, cutting holes and chases in brick or RCC walls/slabs and making good the same to the approval of engineer/consultant complete including painting with one coat of primer and two or more coats of enamel paint of approved make and shade including steel work. Note : Pipes upto and 40 mm dia shall be threaded joints, 50mm and above shall be welded joints.

150mm dia

Providing and fixing CI double flanges suction strainer (PN 20) “Y” type including, nuts, bolts and 3mm thick rubber insertion complete.

150mm dia

200mm dia

Providing and fixing butterfly valves, wafer end type class PN 16 as per IS: 13095-1991 or BS: 5155, including necessary nuts, bolts, gaskets etc. complete (without gear box)

150mm dia nominal bore.

ISI marked (IS:15683) Portable fire extinguisher, of 4.5 kg capacity Carbon-dioxide type flat base including valve, discharge hose of not less than 10 mm dia 1m long & complete in all respects including initial fill with CO2 gas confirming to IS: 307-1966 filled to a filling ratio of not more than 0.667of not more than 0.667and wall suspension bracket.

ISI marked (IS:2878) Portable fire extinguisher, of 22.5 kg capacity Carbon-dioxide type flat base including valve, discharge hose of not less than 10 mm dia 1m long & complete in all respects including initial fill with CO2 gas confirming to IS: 307-1966 filled to a filling ratio of not more than 0.667of not more than 0.667and wall suspension bracket.

'ABC' stored pressure type Dry chemical powder (Mono-Ammonium Phosphate) fire extinguisher with fixing hangers, hose, brackets, screws to required size etc., complete as per IS:15683, 6.0 Kg.

ISI marked (IS:10204) Portable Fire Extinguisher, mechanical foam type capacity 50 ltrs with gun-metal cap and nozzle and complete respects in all respects including initial fill and wall suspension.

Supply, erection, testing and commission of lift travelling from Basement, ground floor to 5th floor, stopping at 7 floors and opening on one side only with/without attendant complete with light in lift shaft and lift pit, providing ladder in lift pit, providing necessary scaffolding required for erection of lifts and minor buildings work comprising of cutting holes and making good the same for the car, counter weight, brackets, call buttons and indicators and including painting of all steel items as required.

Total Amount Rs. Non Schedule Electrical

Total T.S. Amount

Pendent Sprinkler/Upright Sprinkler

Providing and fixing fully glazed MS fully welded construction double leaf door shutter for fire hydrant station fabricated from MS 50x50x6 mm angle iron frame, fixed to wall and hinged MS 40x40x5 mm angle iron door shutter with required MS sash bars for glazing complete with locking arrangements, stove enamelled fire red finish with 'FIRE HYDRANT' written in front.

Providing and fixing pressure gauges with isolation cocks and chrome plated copper pipes as hydrant station to read pressure from 0-25 kg/cm2 complete and of dial dia 150 mm.

Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete.

Supply, Installation, Testing & Commissioning of ISI marked (IS:15683) Portable fire extinguisher, of 4.5 kg capacity Carbon-dioxide type flat base including valve, discharge hose of not less than 10 mm dia 1m long & complete in all respects including initial fill with CO2 gas confirming to IS: 307-1966 filled to a filling ratio of not more than 0.667of not more than 0.667and wall suspension bracket.

Supply, Installation, Testing & Commissioning of 'ABC' stored pressure type Dry chemical powder (Mono-Ammonium Phosphate) fire extinguisher with fixing hangers, hose, brackets, screws to required size etc., complete as per IS:15683, 6.0 Kg.

Supply, Installation, Testing & Commissioning of ISI marked (IS:2878) trolly mounted fire extinguisher, of 22.5 kg capacity Carbon-dioxide type flat base including valve, discharge hose of not less than 10 mm dia 1m long & complete in all respects including initial fill with CO2 gas confirming to IS: 307-1966 filled to a filling ratio of not more than 0.667of not more than 0.667and wall suspension bracket.

Supply, Installation, Testing & Commissioning of ISI marked (IS:10204) trolly mounted Fire Extinguisher, mechanical foam type capacity 50 ltrs with gun-metal cap and nozzle and complete respects in all respects including initial fill and wall suspension.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :

20 mm cement plaster of mix ;

Extra for providing and mixing water proofing material in proportion recommended by the manufacturers: 20 mm cement plaster 1:4(1 cement: 4 sand)

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:

20 mm cement plaster of mix ;

Extra for providing and mixing water proofing material in proportion recommended by the manufacturers: 20 mm cement plaster 1:4(1 cement: 4 sand)

Providing ,supplying and fixing of 18mm thick BWP ply as certified by IS coad specifed of synthetic adhesive, by manufacturers,

S/F/Fixing of Baskets made of 201 grade S.S rod and with around 1%nickel and chrome plating.It has 7mm upper rod and6mm parallel rods and 2.9 mm base rods provided,in all types of baskets. Hetich, KAFF & Godrej

Supply fitting and fixing of approved ISI mark OPEC , DHC electrical chimeny of 90 cm 1200 cum / auto clean touch hood chemeny complete with including installation and insulation of chimeny pipe, nails , screws etc. fixing at site as per approved make and direction of E/I. KAFF, Glen , Faber & Hindware

Supply , Fabrication and installation of wardrob (size : 2175 mm x 2800 mm (H) 600 mm deep) in existing space of master bed room. The structure mode with 18 mm thick BWP Plywood with 1 mm thick Laminates finish on all exposed surface . All complete with fixtures / fittings (hinges , lock magnetic knob, channel, nails screw, etc. ) as per drawings and direction of E/I.

Providing and fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing bright finish brass butt hinges with necessary screw etc complete. (75x65x4mm (heavy type)

providing and fixing chromium plated brass handle with necessary etc.complete.

P&F special quality chrominum plated brass cupboard lock with six lever of approved qualityincluding necessary screws etc. complete.

P&F bright finish brass tower bolt(barrel type)with necessary screw etc complete.

Providing and fixing curtain rods Marvel vista or equivalent of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete:

Providing & Fixing wardrobe , door support , rod of doorset or equivalent make

Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with

Providing and fixing factory made uPVC white colour casement/ casement cum fixed glazed windows comprising of uPVC multichambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance

Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

Casement window single panel with S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 0.75 sqm.)

Providing and fixing factory made uPVC white colour casement/Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single /double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm).

Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.50 sqm)

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension,EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in- Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

Two track two panels sliding window made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Providing and fixing Pre -laminated medium density fibre board exterior grade (Grade-I) IS:14587:1998 marked, to frame, backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately).

Supplying and installation of 3- seater Sofa of model like Godrej Monarch or equivalent as per direction of EI

Supplying and installation of 1- seater Sofa of model like Godrej Monarch or equivalent as per direction of EI

Supplying and installation of Diwan of model like Godrej Adrina Singal Bed without understorage or equivalent as per directionb of EI.

Supplying and installtion of Centre tabel of model like GodrejAcura coffee tabel or equivaleant as per direction of EI.

Supplying and installation of Dinning tabel of model like Godrej Gloria Dinning tabel or equivalent as per direction of EI.

Supplying and installation of Dinner Chair of model like godrej Bruno Dinning Chair or equivalent as per direction of EI.

Supplying and installation of Executive Tabel of model like Godrej Model Enterprise 1350/ w/o CPU hanger or equivalent as per directon of EI.

Supplying and installation of Executive Chair / visitor chair of model like Godrej Bravo visiter Chair or equivalent as per direction of EI.

Supplying and installation of King size Bed of model like Godrej Adria or equivalent as per direction of EI .

Supplying and installation of King size Bed of model like Godrej Adrai or equivalent as per direction of EI.

Supplaying and installation of King Size bed of model like Godrej Adrina or equinalent as per direction of EI.

BED ROOM - 3

FAMILY LAUNGE

Supplying and installation of Centre Tabel of mode like Godrej Splenda Coffee tabel or equivalent as per direction of EI.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I.

Supplying planter box 450 x 450 x 450 mm high made of 19 mm thick BWP ply or equivalent with nessary teak wood beading finished with 1 mm thick laminate of approved colour and quality on all external surface and complete with lipping for MDF board, painted with one coat primer and 2 coats synthetic enamel paint of approved shade and brand payment to be made on the basis of actual plan area.

Providing, fittings & fixing vertical venetian blinds (of vista, mac make) to window made with aluminium slate or approved thickness, colour quality with all accessories including adjuster, hardworks complete with all labour and materials in all floors.Design and colour to be approved first by Engineer-in-Charge.

Providing and fixing 25 mm thick thick wood wall panelling of Armstrong Channelled wood works perforated panels of width 128mm, thickness of 15mm and length 2440 mm or as required by the Architect / approving engineer, made of a high density fibre board with minimum 830 kg / M3 density substrate with a laminated facing / wood veneer as per the approved shade / species & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a "Helmholtz" fluted perforation of 2 mm width and 14mm of visible panel each. The panels shall provide a fire reaction of Class of 1 as per Part 7 of BS 476. The edges of the panels shall be "tongue-and-grooved" to receive special clips for installation.

Providing & fixing of Aluminium Framed preliminated painted board complete wirth fixing of room no. / name plate / exit route in Hostel rooms & chambers of Institute block and hostel as per choice of client / E/I

Double Bed with storage & without Mattress (supplying and placing in position of Double beds (without Mattress) as per detail drawing construction of bed shall be knock down type in nature. Bed Head Board Made out of 18 mm thick commercial Plywood with laminate finish with PVC edge Banding. Bed box made out of 18 mm thick commercial Plywood with laminate Finish. MattressPanel Made out of 12 mm thick Ply with laminate . All exposed edges to be provided with 2.0 mm thick matching grain PVC lipping fixed with hot melt glue. The Product is BIFMA and FSC certified.

Side table - (size : 400L x 400W x 450Ht) Supplying and placing side table with drawer and shelve as per detail drawing. Made out of 18 mm thick commercial Ply with laminate. All exposed edges to be provided with 2.0 mm thick matching grain PVC Lipping fixed with hot melt glue. The product is BIFMA and FSC certified.

Centre Table (Over all demension : Width 600 x Length 1000 x Height 428 Glass thk 8 mm, TABLE MATERIALS : Glass of 08 mm thick tempered, Solid rubber wood legs and frame, MS sheet as bottom shelf PU coating to the rubber wood parts, clear glass)

Coffee / Lounge chair Supply and installation of Hardwood / rubberwood framed chair with fabric upholestry with provision of PU foam on sheet and back complete with melamine polish and all necessary hardware.

Dining Chair (COCO : Dining Chair STACKABLE CAFÉ CHAIR : Size : (L) 381 mm x (D) 419 mm x (H) 839 mm seat and Back in PVC moulded chair with SS 202 Grade frame round pipe colour Green, Black, Red, yellow, Blue, Brown, Orange, white)

T.V (32 " LED ) (3 years warranty , welcome video/screen, quick menu (2.0) Audio Playback, compatibility with AV control system

T.V (48 " LED ) Supply installation and testing commissioning of 48" LCD / Plasma T.V. of sony, L.G., Samsung or equivalent approved make with suitable Stablizer

Dressor (with storage & Mirror) Size : 1500 L x 475 W x 1500 Ht. Supplying and placing dresser with drawer and shelve as per detail drawing Made out of 18 mm thick commercial ply with laminate with PVC edge Banding. All exposed edges to be provided with 2.0 mm thick matching grain PVC lipping fixed with hot melt glue. The product is BIFMA and FSC certified.

Wooden Wardrob (size : 1200 L x 1975 H x 600 D) Making, supply and installation of Wooden Wardrob, 600mm deep, The sides, Top of B.W.P. lesard with 1.0 mm laminated finish. 12 mm thick B.W.P. Ply The front shutter with 19 mm thick B.W.P. Ply wood of century ply or equivalent with 1.0 mm thick. laminates movable roller, channel, recess knob Itallica Locks glass etc. shall be complete in all respect.

Sofa Set 2 seator 2 seator sofa for lounge seating of overall size 146 cm (W) x 92 cm (D) x 82 cm (H) & Seat Height 45 cm. 1) Seat Foam The seat is made of PU foam with Density 322 kg/cu mtr. Seat is upholstered with fabric or leatherette. 2) BACK FOAM - The back is made of PU foam with Density 282 kg/cu mtr. with two additional top layer of super soft foam of density 232 kg/cu mtr. upholstered with fabric or leatherette. 3) UNDERSTRUCTURE : Understructure is made up of 1.2 0.1 cm thick hot pressed plywood measured as per QA method described in OCP. QLTA-PL14-184 dia 4 mm zigzag spring assemly is mounted in understructure for support and additional cushioning purpose 4) LEG ASSEMBLY : It is a welded assembly made in stainless steel (grade SS 202) tube & plate.

Sofa (1 seator) Supply and installation of Leatherlite / Fabric over PU foam in sitting and back over M.S. / Hardwood frame, Upholestor armrest all bases to be of chromefinish or polished wood finish..

Dining Table (1200 x 750 x 760) -4 seator Supply, Fabrication & Installation of Dining table made of Wood veneer / Powder coated MS frame with 12mm thick glass top complete in all respect. as per drawing and direction of E.I.

Reception Table Main Table size : 1500L x 600 W x 1050 Ht. Side runner size 900 L x 450 W x 750 Ht. Supplying and placing in position of the Reception table work top made out of 18 mm thick commercial Plywood with Laminate Finish which shall be supported on side panels & Modesty panels. Side's panels and Modesty panel should be made from 18 mm thick commercial Plywood with laminated finish above table top 10 mm thick clear glass fixed with stud. supplying, and placing in position of storageas per photograph. The modular storage unit top shall be made from 18 mm thick commercial plywood with laminate finish and rest of the sides as well as shelves and shutter to be made up of 18 mm thick commercial plywood with laminate finish. All edges to be provided with 2 mm thick PVC lipping each unit to have openable shutters with locking provision. The product should be from BIFMA certified company . Complete as per image and specification under the guidance of Engineer in charge. Chairs KAPLAN.

Dining Table - Size : (1800 Lx 750 W x 750 Ht) - Supplying, and placing in position of Dining Table as per photograph table top shall be made up from 18mm thick commercial plywood with laminate finish and table top supported with leg made of CRCA of 1.2 mm thick of size 50mm x 50 mm with powder coating of 50 micron & horizontal connectors made of CRCA of 1.2mm thick of size 50mm x 50 mm with powder coating of 50 micron The working edges shall be provided with machine pressed 2 mm thick PVC edging using special hot melt glue at hot temperature. The product should be from BIFMA and FSC certified company. complete as per image, Durian make and specification under the guidance of Engineer in charge dinning chair.

Study Table (size :1200 x 1200 x 750) Supply, Fabrication and installation of rectangular table of size (1200 x 1200 x 750 H) with preliminated Particle board top over chrome base leg all complete as per drawing design and direction of E/I.

Circular Table (size :900 Dia) - Supply, Fabrication and installation of rectangular table of size (900 Dia x 750 H) with preliminated Particle board top over chrome base leg all complete as per drawing design and direction of E/I.

Study Chair /Breakfast chair Supply and installation of Telemate medium back chair with single point lock tilting mechanism castor and latherlite sheet over PU foam sheet complete on crome base

"Low Height Credenza- (900x600x900ht) RAGE/Credenza Providing 750mm high, 600m deep storages. Structure manufactured in 18mm thick both side pre laminated MDF boards for sides, top, bottom and internal shelves and 9mm thick for back as per approved shades,. All edges duly banded with 0.4mm PVC edge banding with hot melt glue and machine trimmed. Front shutters over lapping the carcass edges in 18mm thick high pressure laminate (HPL) post formed in half round profile with particle board substrate, back side also laminated. Short sides edge banded as above in approve shade. Concealed stainless steel hardware including metal dowels, spring loaded hinges, locks, handles, tower bolts, and other fixtures accurately fixed with necessary machines/drills/tools etc.. complete as per detailed drawings/as per direction of E/I " Low ht.credenza size 450mm deep X 750mm high

Electric Kettle Supplying of Electric kettle of reputed make (Philips, Milton or Equivalent ) as per client choice

Study Lamp / Bed side lamp Supply & fixing Study lamp of reputed make (Bajaj,Philips or Equivalent) as per shown in drawing and direction of E.I.

Water Purifier (Dual protection stainless steel tank, Mineral Booster- 2 -in 1 water solution, everfresh UV plus smart Display filter change & UV sterlizing indicators)

Room Heater (Wave style fins for better heating efficiency,PTC heating element with 400 w fan for faster heating. Powder coated fins for rust protection in build tip over switch.

Matress (Size 1950 x 1800 x 125) memory foam matters as per Bed size

Pillow (425 x 675) micro fibre

Blanket (2500 x 2250)

White spiral Bed sheet (2700 x 2700)

Geyser (Wave style fins for better heating efficiency, PTC heating element with 400 w fan for faster heating, powder coated fins for rust protection in build tip over switch

Microwave Oven ( Bigger capacity (42 Litre) smart invertor sleek and practical design, Easy clean, Stable tumtable ring cmpact size, smart diagnosis.

Total R.T.S. Amount

Gr-01, Construction of 50 Bedded Integrated Ayush Hospital ,Dist.-Darbhanga

BMSICL (A Govt. of Bihar Undertaking)

Group A (Schedule item ) – Rs 12,74,56,356.00 Group B (Non schedule item) – Rs 92,95,764.00 TOTAL(A+B) Rs.-13,67,52,120.00 (Rupees Thirteen Crore Sixty Seven Lakhs Fifty Two Thousands one Hundred twenty only.)

12 Months

in percentage above /Below/Atpar

Group A Tendered Rate comparison to B.O.Q.Amount in percentage (in Figure)

Group B (Item rate) total amount in Figure

Item code

Earth work in excavation over areas (exceeding 30 cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m; disposal earth to be levelled and neatly dressed.

Extra for every additional lift of 1.5 m or part thereof in :

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth : consolidating each deposited layer by ramming and watering lead.

Supplying and filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.

Extra for providing and mixing water proofing material in cement concrete work in the proportion recommended by the manufactures.

Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases of columns, pile caps etc., for mass concrete.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc. (in OHWT, Lift , Basement wall)

Columns, Pillars, Piers, Abutments, Post and struts

Stairs, (excluding landings) except spiral staircases.

Wheather shade, Chajja, corbels etc., including edges.

Edges of slabs and breaks in floors and walls :

metre

Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards

Reinforcement for RCC work including straightening. Cutting, bending, placing in position and binding all complete.

TMT -500- 8mm dia .

TMT -500-10 mm dia.

TMT -500-12 mm dia.

TMT -500 -16 mm dia.

TMT -500 -20 mm dia.

TMT -500 -25 mm dia.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work upto plinth level

All work above Plinth level upto floor V Level.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering and shuttering, finishing and reinforcement - All work upto plinth level.

Brick work with bricks of class designation 100A in foundations and plinth in :

Cement mortar 1:6 (1 cement: 6 coarse sand )

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in

Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work

Half brick Masonary with non modular fly ash bricks of class designation 10,conforming IS:12894,in superstructure above plinth and upto floor V level. Cement mortar 1.:3 (1 cement: 3 coarse sand )

Extra tor Brick work in superstructure above plinth level upto floor V cum

Half brick masonry with bricks of class designation 100A in foundations and plinth in :

Cement mortar 1:4 ( 1 cement: 4 coarse sand)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with nuts and screws etc.

Providing and fixing aluminium sliding tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with nuts and screws etc.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (Over all area of door shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs, and priming coat on unexposed surface etc. complete.

metre

Providing and fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C.doors) using synthetic rubber based adhesive.

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - incharge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per direction of Engineer-in- charge. The glass shall be clear, toughened, interlayered, non-wired fire resistant having 11 mm thickness of approved brand with 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 15 min of insulation (EI15) and having a sound reduction of ?37dB and LT of 86%. Glass shall be compliant to class 2(B)2 category of Impact Resistance as per EN 12600. The glass should be manufactured in UL & TUV audited Facility and including UL-EU Certification.The maximum glazing size cannot be more than 1100 mm x 2200 mm (w x h) or 2.42 sq mts in total area. The test report for the complete system (Glazed Door or Partition) will be considered valid only if it contains the stamp and signature of the authorized signatory from the glass manufacturer. (Actual glass size is to be measured at site for payments).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.50 mm all complete.

For fixed portion

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5.50 mm thickness

With float glass panes of 8 mm thickness(weight not less than 20 kg/sqm).

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

Providing and fixing 100 mm brass locks (best make of approved quality for aluminium doors including necessary cutting and making good etc. complete

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in Charge

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings, the aluminium quality as per grade 6063 T5 or T6 as per BS 1474, including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-charge. (The item includes cost of fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account)

Designing, fabricating , testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the buildings for all heights and all levels,including

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

Providing and fixing pressed steel door frame confirming IS code 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-Charge.

metre

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.).

Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying a priming coat of approved steel primer

Providing and fixing M.S. grills of requirement pattern in frames of windows etc. with M.S. flats, square or round bars etc.all complete

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/I.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such shades except white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Stone tile work for wall lining upto 10.0m height with special adhesive like araldite or equivalent over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand ) including pointing in-white cement with an admixture of pigment to match the stone shade.

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

Chequerred precast cement concrete tiles 22 mm thick with marbie chips of size 6 mm in footpath & coutyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning tec. Complete on 20 mm thick bed of cement mortar 1:4(1 cement:4 coarse sand)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of 1:1:1 (1 lime : 1 surkhi : 1 coarse sand) / 1:4 (1 cemnt : 4 coarse sand)

Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20mm(avearage) thick base of cement mortar 1:4(1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Cement concrete flooring 1:2:4 (1cement : 2 coarse : sand 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete.

12 mm cement plaster of mix

15 mm cement plaster on rough side of single or half brick wall of mix.

18 mm cement plaster in two coat under layer 12 mm thick cementplaster 1:5 (1 cement: 5 course sand) and a top layer 6mm thick cement plaster 1:3(1 cement: 3 coarse sand finiished rough with sponge

18 mm cement plaster in two coat under layer 12 mm thick cementplaster 1:5 (1 cement: 5 course sand) and a top layer 6mm thick cement plaster 1:3(1 cement: 3 coarse sand finiished rough with sponge

6 mm cement plaster to ceiling of mix :

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of cement primer of approved brand and manufacture on wall surface:

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade.

Applying priming coat:

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens,nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Neat Cement punning

Stone work (machine cut edge) for wall lining etc. (veneer work) over 12 mm thick bed of cement lime mortar 1:1:6 (1cement : 1 lime putty : 6 fine sand) including pointing in white cement mortar 1:2 (1 white cement: 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing by means of cramps which shall be paid for seperately)

Providing and fixing gun metal cramps of required shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 fine sand) including making the necessary chases.

Finishing walls with Acrylic Smooth exterior paint of required shade :

Extra for plastering exterior walls of height more than 10m form ground level for every additional height of 3 m or part there of

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed protions of W.C. kitchen and the like consisting of :

1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.

IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.

IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area.

IVth course of 400 micron thick PVC sheet (overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm

Providing and Laying APP (Atactic Polypropylene polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre /sqm by the same membrane manufacture of density at 250 C, 0.87-0.89 kg / litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The Vital physical and chemical parameters of the membrane shall be as under : Joint strength in logitudinal and transverse direction at 230 C as 650/ 450N / 5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 1500C. Cold flexibility shall be upto -20C when tested in accordance with ASTM, D-5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100%polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

With chlorpyriphos / Lindane E.C. 20% with 1% concentration.

With Chlorpyriphos/ Lindane E.C. 20% with 1% Concentration.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand ) to match the existing floor.

Providing well brunt brick bats or jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1:10) all complete as per building specification and direction of E/l.

With 20x20mm square bar

500 mm diameter C.I cover (medium duty) the weiht of he cover to be not less than 58 kg.

560 mm diameter C.I. over (heavy duty) the weight of the cover to be not less than 108 kg.

80 mm dia. Nominal bore

100 mm dia Sand cast iron S&S pipe as per IS : 1729

100 mm diameter Class I

80 mm diameter pipe

80 mm diameter pipe

80 mm dia. Nominal bore

Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor pilesmethod and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge.

Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ Sonic Echo Test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud, dust & chipping lean concrete lumps etc. and use of computerised equipment and high skill trained personal for conducting the test &submission of results, all complete as per direction of Engineer-incharge.

Excavating , supplying & filling of local earth (including royalty but excluding carriage cost) by mechanical transport upto lead of 3km also incliding ramming and watering of the earth in layers not exceeding 20cm in trenches , plinth ,sides of foundation etc. complete . if local earth is available at more than 3km lead the actual lead must be approved by compitent authority. cairriage of material will be paid seperately after deducting initial lead

Bricks (lead - 1 km kutcha + 7 km pucca)

Coarse sand (1+134KM from Kiul)

Stone Chips (357 KM from Pakur by Rail + 26 km By Road)

Local sand ( 1 km kutcha + 2 km pucca)

Cement P.S.C

Bricks

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required :

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50 cm deep and 1.8cm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4(1 cement: 2 coarse sand: 4 graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Providing and fixing Salem Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with CI brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :

Providing and fixing P.V.C. Waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. (WB & Urinal)

Providing and fixing toilet paper holder :

Providing and fixing uplasticised PVC connection pipe with brass ions :

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in-charge

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms.

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms.

Providing and fixing PTMT towel rail complete with brackets fixed wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Provding and fixing 600X450mm beveled edge mirror of superior glass complete with 6mm thick hard board ground fixed to wooden cieats with CP brass screws & washers complete.

Providing and fixing Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 soil, waste and vent pipes .

Metre

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. Sand cast iron S&S as per IS - 3989.

Providing and fixing plain bend of required degree Sand cast iron S&S as per IS - 3989.

Providing and fixing heel rest sanitary bend.

Providing and fixing double equal plain junction of required degree.

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

Providing and fixing single equal plain junction of required degree.

Providing and fixing single unequal plain junction of required degree :

Providing and fixing terminal guard.Sand cast iron S&S as per IS - 3989.

Providing and fixing collar.Sand cast iron S&S as per IS - 3989.

Providing lead caulked joints to sand cast iron/ centrifugally cast (spun) iron pipes and fittings of diameter :

Providing and fixing MS Stay clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter.

Providing and fixing M.S. cap 100 mm dia and M.S. socket 100 mm dia

Providing and fixing trap of self cleansing design with screwed down or hinged with or without vent arm complete, including cost of cutting and making good the walls and floors.

Painting sand cast iron/ centrifugally cast (spun) soil, waste, vent pipes and fittings with paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work.

Metre

Providing and fixing on wall face unplastidsed - PVC (working pressure 4 kg per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Metre

Providing, fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised - Rigid PVC rain water pipes conforming to IS ; 13592 Type A including jointing with seal ring conforming to IS ; 5382 leaving 10 mm gap for thermal expansion.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50 x 50 x 50 mm hard wood plugs, screwed with M.S screws of required length, including cutting brick work and fixing in cement mortar 1:4( 1 cement: 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Metre

Metre

Metre

Metre

Metre

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.

Metre

Metre

Metre

Metre

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

Metre

Metre

Metre

Metre

Metre

Metre

80 mm dia nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :

Metre

Metre

Metre

Metre

Metre

Metre

Metre

Providing and fixing gun metal gate valve with C.I. wheel of approved quality.

20 mm Nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

Providing and fixing PTMT grating of approved quality and colour.

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing CP Brass shower rose with 15 or 20 mm inlet

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

Cutting holes up to 15 x 15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , including finishing complete so as to make it leak proof.

DRAINAGE

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50m:

Metre

Providing, laying and jointing glazed stoneware pipes class SP-1 'A' with stiff mixture of cement mortar in the proportion of 1:1(1 cement: 1 fine sand) including testing of joints etc. complete.

Metre

Providing and laying cement concrete 1:5:10( 1 cement: 5 coarse sand:10 graded stone aggregate 40mm nominal size) all-round S.W pipes including bed concrete as per standard design.

Metre

Providing and fixing square mouth SW gully trap grade A complete with CI grating brick masonry chamber with water tight CI cover with frame of 300X300mm size(inside) the wt. of cover to be not less than4.50kg. And frame to not less than 2.70 kg. as/standard design

Providing and laying non -pressure NP2 class R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 including testing of joints etc.

Constructing brick masonry manhole in cement mortar 1:4(1 cement: 4 coarse sand) R.C.C top slab with 1:2:4 mix (1 cement:2 coarse sand: 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 coarse sand:8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand:4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design:

Extra for depth for manholes

Metre

Constructing brick masonry chamber for underground C.I inspection chamber and bends with 75 class designation bricks in cement mortr 1:4( 1 cement: 4 coarse sand) C.I cover with frame (light duty) 455x610mm internal dimensions, total weight of cover with frame to be not less than 38 kg(weight of cover 23 kg and weight of frame 15 kg) R.C.C top slab ith 1:2:4 mix ( 1 cement: 2 coarse sand:4 graded stone aggregate 20mm nominal size) foundtion concrete 1:5:10( 1 cement: 5 fine sand:10 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Extra for depth beyond 45cm of brick masonry chamber:

Metre

Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with brick of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

DRAINAGE FOR RAIN WATER

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50m:

Metre

Providing and laying non -pressure NP2 class R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 including testing of joints etc.

Constructing brick masonry manhole in cement mortar 1:4(1 cement: 4 coarse sand) R.C.C top slab with 1:2:4 mix (1 cement:2 coarse sand: 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 coarse sand:8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand:4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design:

Extra for depth for manholes

Metre

Constructing brick masonry chamber for underground C.I inspection chamber and bends with 75 class designation bricks in cement mortr 1:4( 1 cement: 4 coarse sand) C.I cover with frame (light duty) 455x610mm internal dimensions, total weight of cover with frame to be not less than 38 kg(weight of cover 23 kg and weight of frame 15 kg) R.C.C top slab ith 1:2:4 mix ( 1 cement: 2 coarse sand:4 graded stone aggregate 20mm nominal size) foundtion concrete 1:5:10( 1 cement: 5 fine sand:10 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Extra for depth beyond 45cm of brick masonry chamber:

Metre

Constructing brick masonry circular type manhole 1.2 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

Metre

Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS : 10910 on12mm dia steel bar conforming to IS :1786 having minimum cross section as 23mm x 25mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protrude legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) complete as per design.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

Metre

Metre

Metre

Metre

Metre

Metre

Metre

Metre

Metre

Metre

Metre

Metre

Metre

Providing and fixing gun metal gate valve with C.I. wheel of approved quality.

Providing and fixing G.I. union in G.I.pipe including cutting and threading the pipe and making long screws etc.

Providing & fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc.(the tail pieces if required will be paid separately)

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

Constructing masonry chamber 60x60x75 cms inside, in brick work in cement mortar, 1 : 4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter ,160 mm bottom diameter and 180 mm deep (inside) with chained lid and rcc top slab 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation foundation concrete 1:5:10 mix (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :

Boring/drilling bore well of required dia for casing/strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level.

Boring/drilling bore well of required dia for casing/strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS:12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

Metre

Gravels packing in tubewell construction in accordance with IS 4097 including providing graval fine/medium/coarse,in required grading & sizes as per actual requirement,all complete as per direction of Engineer-in charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by V notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing & fixing suitable size threaded mild steel cap or spot welded plate to the top of borewell housing/ casing pipe ,removable as per requirement,all complete for borewell of,

Providing & fixing MS clamp of required dia to the top of housing/casing pipe of,removable as pe tubewell as per IS;2800(part-I), including necessary bolts & nuts of required size complete

Providing & fixing Bail plug/ bottom plug of required dia to the bottom of pipe assembly as per IS;2800(part-I),

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed heavy class Steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed Steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed Steel conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed Steel conduit alongwith 2 Nos 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed Steel conduit as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos.3 pin 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc. as required. for UPS Power

Supplying and fixing suitable size GI box with rnodular plate and cover in front on surface or in recess, including providing and fixing 3 nos. 5 pin 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc. as required. for UPS Power

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 amps “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing stepped fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing of modular Blanking plate on the existing modular plate & switch box excluding modular plate etc. as reqd.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

Supply and fixing following modular switch/socket on the existing modular plate and cover plate & switch box including connections but excluding modular plate etc. as required.

Data Socket Outlet RJ -45 suitable for CAT 6

Supplying and fixing following size/modules, GI box along with modular base and cover plate for modular switches in recess etc as required.

Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface/ recessed PVC conduit as required.

Supplying and drawing co-axial W cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required.

Supplying and fixing following way, Horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, single pole and neutral, prewired, sheet steel, MCB distribution board, 240 volts, on surface/recess, complete with loose wire box ,terminal blocks, duly prewired with Suitable size FR PVC insulated Copper conductor upto terminal blocks, tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing complete etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc.as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supptying and fixing following rating, 24Al4L5 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required'

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing recess mounted downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing 70112 watt LED type Bulk-head luminaire with minimum efficacy 100 lm/w in comprising of pressure die cast housing, acrylic diffuser,lP 65 protection and complete u.,ith integrated electronic driver etc directly on wall/ceiling including connections with 1.5 sq. mm FRLS PVC insulated copper conductor cable etc as required.

Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 270 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required.

Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required.

Bell push

Providing and fixing of lightning conductor finial, made of 25 mm dia 300mm long, G.I. tube, having single prong at top, with 85mm dia 6mm thick G.I. base plate i ncluding holes etc. complete as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Jointing copper /G.I. tape (with another copper/ GI tape, base of the finial or any other metallie object) by riveting /nut bolting/sweating and soldering etc as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Online UPS- Input supply: Single Phase, Output supply: Single Phase Online double conversion true sine wave Uninterrupted hot swapable (allow for the replacement or addition of battery modules without shutting down the entire system) modular Power Supply (UPS) system with N+1 modules (N denotes total number of moduels requird for rated capacity) with 30 minute backup.

Ten Loop Panel.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed temperature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supply and fixing fabricated Feeder pillar of cubical construction, floor mounted type, fabricated out of 14 SWG CRCA sheet, compartmentalised with hinged doors, dust and manufactures. (But without RYB LED lamp, ammeter, vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator, with 40mm X 40mm X 5mm angle iron stand and complete in all respect etc and must be CPRI approved panel voltmeter, inter-connection copper conductor cable/solid

630 A, 50 KA, FP MCCB

630 A, 50 KA, FP MCCB

400 Amp 50 KA FP 415 volt MCCB.

200 Amp 36 KA FP 415 volt MCCB.

100 Amp 25 KA FP 415 volt MCCB.

40 A to 63 A rating, TPN MCB, "C" curve, 10 KA breaking ca pacity

50 mm X 5 mm copper strip (2.30 Kg/mtr)

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

Supply and fixing of fabricated Electrical control panel of cubical construction, floor/wall mounted type, fabricated out of 16 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator and complete in all respect etc and panel manufactures must be approved by CPRI. (But without RYB inicator, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears etc.)

400 Amp 50 KA FP 415V MCCB. (Incomer)

160A 4 Pole MCCB, 36 KA,

100A 4 Pole MCCB, 30 KA, For LIFT

40 A to 63 A TPN MCB 415 Volt, (Power & Light DB)

6/32 Amp SPN MCB 240 Volt

50 mm X 5 mm copper strip (2.30 Kg/mtr)

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

Providing and fixing MV danger notice plate of 200mm x 150 mm made of mild steel at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side etc as required.

Supply and fixing of fabricated Electrical control panel of cubical construction, floor/wall mounted type, fabricated out of 16 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator and complete in all respect etc and panel manufactures must be approved by CPRI. (But without RYB inicator, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears etc.)

160A 4 Pole MCCB, 36 KA,

50 mm X 5 mm copper strip (2.30 Kg/mtr)

40 A to 63 A TPN MCB 415 Volt, 10KA (Power & Light DB)

6/32 Amp SPN MCB 240 Volt

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

Supply and fixing fabricated Feeder pillar of cubical construction, floor mounted type, fabricated out of 14 SWG CRCA sheet, compartmentalised with hinged doors, dust and manufactures. (But without RYB LED lamp, ammeter, vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator, with 40mm X 40mm X 5mm angle iron stand and complete in all respect etc and must be CPRI approved panel voltmeter, inter-connection copper conductor cable/solid

1 No. of 100 Amp 4P MCCB of 30 KA thermal over load and magnetic short circuit release and matching contactor and 24 hrs timer for street light controls.

Supplying, installation, testing and commissioning of Astronomical time switch capable of following output in feeder pollars / Lighting DB's for automatic switching ON & OFF of strret lights at sun set & sun rise of twilight (Auto ON, Auto OFF, Auto) with manual override facility with 12124 hour display format with suitable battery and indication for relay status i/c programming at site complete as requii-ed.

50 mm X 5 mm copper strip (2.30 Kg/mtr)

32A rating, TPN MCB, "C" curve, 10 KA breaking ca pacity

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

Providing and fixing MV danger notice plate of 200mmX150mm made of mild steel at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side etc as required.

Supply and fixing of fabricated Electrical control panel of cubical construction, floor/wall mounted type, fabricated out of 16 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator and complete in all respect etc and panel manufactures must be approved by CPRI. (But without RYB inicator, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears etc.) LIFT PANEL - (in Lift Machine Room)

100A 4 Pole MCCB, 30 KA

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

50 mm X 5 mm copper strip (2.30 Kg/mtr)

63A 4 Pole MCB's of 10 KA service breaking capacity.

2 Nos. 40 amps DP MCB of 10 KA service breaking capacity

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. (For Street light Feeder pillar, DP Structure, & fire panel etc)

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. (For Transformer, DG, Main feeder, Building panel)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. (For Transformer & DG Neutral & LIFT & UPS)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Supplying and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.l. pipe from earth electrode including connecion with copper thimble excavation and refilling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. (For Street light pole to pole etc)

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required.

Supply and erection of 7 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 155 mm, made of 3 mm thick sheet along with base plate of size 260 X 260 X 16 mm , small door opening for junction box mounting with MCB & connector, cement concrete of 1:3:6 including excavation, refilling and suitable size foundation bolts with template and all complete job as required. (but without pole collar)

Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

Supplying & embedding of following dia G.I. pipe (medium class) in pole collor / foundation (during casting ) for cable entry including bending the pipe to the required shape complete etc. as required.

Supplying and fixing post top / gate light (width 250/300 mm) made up of high grade unbreakable polycarbonate material suitable for upto 20 watt LED lamp including connections and earthing the body etc as required. ( But without lamp)

20 watt LED lamp

Providing and making steel pole collar with cement concrete 1:3:6 (1 cement:3 coarse sand:6 stone aggregate 20 mm) of specified size and shapeincluding form work, plastering if required, curing etc. as required. (volume of pole/pipe not to be deducted)

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power H.T. cable with aluminium conductor for working voltage upto 11 KV as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

Supply of following sizes and core of PVC/XLPE insulated PVC sheathed heavy duty, aluminium conductor armoured under ground cable of graded 1.1 KV for working voltage upto 1100 volts conforming to ISI 1554 (Part-I) of 1964 with upto date amendment as detailed below.

Laying of one number insulated and PVC sheathed power cable of 1.1 KV grade of following size direct in ground including excavations, sand cushioning protective covering and refilling the trench etc. as required.

Laying and fixing of one number PVC insulated and PVC sheathed aluminium conductor cable of1.1 KV grade of following size on surface etc. as required.

Laying of one number PVC insulated and PVC sheathed aluminium conductor cable of1.1 KV grade of following size in the existing RCC/ HUME/METAL pipe etc. as required.

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as reguired.

Supplying, Installation, Testing & Commissioning of ‘Silent Type Diesel Generating set as per CPCB IV + or better norms along with having Prime Power Rating of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor, including testing at factory and site with fuel, load for test and other necessary arrangements Complete as per CPWD specifications, should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location, rating plate as per relevant IS Code etc. and consisting of the followings:

Supply, installation, testing and commissioning of following capacity (continuous loading) BEE 3 Star rated (Corresponding Level as per BIS amended upto date of receipt of tender) , 11/0.433 KV step down, 3 Phase, 50 Hz, Dyn 11 vector group, ONAN (Oil Natural Air Natural) copper wound transformer (Electrolytic grade 99.9% pure copper, Core made of first grade Cold Rolled Grain Oriented (CRGO) Core grade MOH or better, suitable for out door/indoor applications with Offload Tap Changer/ On Load Tap Changer (OLTC) ( below 500 KVA offload and above 500 KVA On Load Tap Changer) on HV side having AVR relay and Remote Tap Changer Control (RTCC) for automatic sensing of incoming voltage, automatic operation of OLTC and facility for remote and manual operation of OLTC HV side in range of +5% to -15% in steps of 2.5%, having cable end boxes on HV side suitable for 3x300 sq.mm XLPE cable of 11 KV grade, including bus trunking arrangement on LV side including supplying and laying of copper conductor multicore control cable from transformer to HT breaker/panel for safety tripping, complete with all accessories and safety provisions as per relevant IS Code including first filling of filtered dehydrated oil, i/c

or explosion vent above 200 kVA; k) One filter valve on the upper side of the tank (for transformers above 200 kVA); l) Unidirectional flat rollers (for transformers above 200 kVA); m) Inspection hole (for transformers above 200 kVA); n) HV side neutral grounding strip (where one of the HV bushing terminal is connected to earth); o) Buchholz relay for transformers above 800 kVA. p) Arcing horns or suitable rating lightning arrestors for HT side – 3 Nos. q) Bird guard; r) Oil temperature indicator and winding temperature indicators for transformers above 200 kVA with suitable tripping mechanism above permissible limit s) Jacking pads (for transformer above 1 600 kVA); t) Additional Neutral separately brought out on bushing for earthing. u) Magnetic oil level gauge (for transformer above 1600 kVA) with low oil level alarm contact; v) Non return valve (for conducting pressure test); w) Pressure relief device or explosion vent x). Monogram Plate y) Inspection cover z). Detachable type radiators with top and bottom shutoff valve. aa) Oil Conservator with Oil level indicator, minimum level marking and drain plug for all transformers of capacity 50 KVA and above. bb) Necessary hardware, clamps, lugs etc. for termination on HV/MV etc. for all transformers.

Total

Supplying, Installation, Testing & Commissioning of following capacity passenger cum bed lift Machine room less (MRL) Bed lift with regenerative drive as per CPWD General Specification for Electrical Works (Part-III Lift & Escalator) 2003, BIS Codes, NBC 2016 as amended upto date having provision for barrier free access as per Harmonised Guidelines & Standards for Universal Accessibility in India - 2021 of MoHUA, serving different floors in the lift shaft as per detailed specifications enclosed and as under including all other equipment and accessories complete as required :-

(xv) The lift doors shall have a vision panel to enable persons with hearing impairment to signal for help or assistance in the event of an emergency. (xvi) An appropriate technological support be provided (Through emergency messaging |services or alarms etc.) to respond to the emergency requirements of person with hearing impairment or deafness. (xvii) In case of failure of ARD or other electronic devices, a provision of manual rescue be provided.

FIRE PUMPS - ELECTRICAL

a) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump)

b) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520.

c) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325.

c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

(d) Suitable cement concrete foundation duly plastered with anti vibration pads.

FIRE PUMPS - DIESEL

a) Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Drive Pump)Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

b) Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio ndications, painted with post office red colour etc. as required.

c) M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required.Suitable cement concrete foundation duly plastered and with anti vibration pads.

Supply, installation, testing, trial run and commissioning of hydrants all complete as required and as approved

Fire Hose Cabinet

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following asrequired.

20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585

20 mm nominal internal dia gun metal globe valve & nozzle.

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

Providing and fixing up to floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc. including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required centering, shuttering and finishing smooth with 6mm thick cement plaster 1:3 (1 Cement : 3 fine sand) on exposed surfaces complete.

Constructing masonary chamber 90 x 90 x100 cm. inside with 75 class designation brickwork in cement mortar 1:5 ( 1 cement : 5 fine sand) for sluice valve with CI surface box 100 mm top dia. 180 mm bottom dia. And 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1 :5 :10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size and inside plastering with 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design with FPS bricks

Providing and fixing C.I. double acting air valves of approved quality with bolts, nuts, rubber insertions etc. complete ( The tail pieces, tapers etc. if reqd. will be paid separately)

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

Providing, installation, testing and commissioning of stainless steel Ystrainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts,gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with oaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS:1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : (Above Ground)

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases,strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves,MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, ompartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm x 5 mm. G.I. strip in 40 mm dia. G.I. Pipe from earth electrode, including connection with GI nut, bolt, spring, washer excavation and re-filling etc as required.

Providing & fixing 25mm x 5mm G.I. strip on surface or in recess for connections etc. as required.

Providing and Fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing alongwith existing surface/ recessed conduit/ submain wiring/ cable as required.

Supplying, fabricating and installing following size of perforated painted with powder coating M.S. cable trays,with perforation not more than 17.5%, in covenient section, joined with connectors, suspended from the ceiling with MS suspenders including bolts & nuts, painting suspenders etc. as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Supplying of all materials and making terminations of 1.1 KV grade aluminium multicore cables of the following sizes. The work includes cable glanding using brass plated double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/ thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals.

Control Cabling (PVC insulated and PVC sheathed, armoured, Copper Conductor of 1.1 KV grade on existing cable trays).

Supplying , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180- 260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 0C. Min 5 year OriginalEquipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electrotechnical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient temperature).

Item code

Providing and Fixing 2 mm thick homogeneous vinyl flooring in rolls with Weight ≤ 2750 g / m2, abrasion value according to EN 660.2 ≤ 2.0 mm3, group T, binder content type I, class load 34/43, residual indentation ≤ 0.03mm. Fire classification Bfl-s1. TVOC after 28 days <10 ppm / m3 according to ISO 16000-6. REACH compliant.ISO717-2 Weighted improvement of impact sound inslation is 4db.It should be non directional in design . Evercare surface treatment to make it highly resistant to strong chemical used in the healthcare industry like Betadine ,antibacterial gel,eioson oil etc

Providing and Fixing 1.0mm homogeneous vinyl wall covering. Roll width of 2 m. Fire classification Bs2-D0. PUR Protect surface treatment. Easy welding. 100% recyclable. REACH compliant and 100% recyclable

Providing, fixing, testing & commissioning of Submersible pumping set (Willo submersible pump , cat no.- WBWP4L PRATHAK 30/09/65) 3 phase, 09 stage with pannel bord , cabel etc. All complete

Submersible Tubewell Pump

Supplying, Installation, testing and commissioning of following sizes of telephone distribution board in M.S. hinged type box duly painted complete with Krone type tag block etc. including terminations of cable as required.

SITC of Nurse Call Station, with LCD display, the central console with the necessary display all buttons, housed in a dust and water protected cabinet with view panel, having at least the following features: Electronic digital bed number annunciation displays, Speaker for audible voice alert. Periodic reminder chimes. iscernable emergency audio alert, distinctive display for normal call, emergency and nurse presence. Single acknowledgement buttons for calls from all beds. Main Supply input 230V+/-15%, 50 Hz. System power supply: 12V DC or less. Plug in type PCB's for easy service & replacement, under desk terminal box for ease of access & maintenance. Brass screw erminals only- for all incoming line wires. Body & chasis fabricated from epoxypolyster powder coated aluminum etc as required complete in all respect.

10 Beds Module

SITC of Patient Hand Module consisting of recessed 1 nos. call buttons for calling nurse, call status indicators with 3 color LED lamps including 2.5 mtrs flexible spring cord.

SITC of Door Indicator modules with high luminosity call status indicators with 3 colors LED lamps for corridor wide visibility, complete as per specification( outside of ward/doctors room)

Carbon dioxide (CO2) type fire extinguisher (conforming to IS 2878) with cylinders fully charged of capacity 4.5 Kg.) mounted on wall hooks.

Dry chemical powder type fire extinguisher of 6 kg capacity as per IS 2171 mounted on wall hooks

SITC of G.I. buckets of 5 Nos. 9.5 litres capacity painted with red oxide paint and written with White paint 'Fire' and mounted on free standing stand as required including filling with dry sand.

SITC of First aid box as approved by St. John Ambulance Brigade/Indian Red Cross conforming to IS : 2217-1963.

SITC of shock treatment chart in Hindi and English duly mounted on a wooden frame with glass

Rubber mat 914.4 mm. wide and 12 mm. thick to withstand 11 KV dielectric strength as per IS 5424 - 1969.

Rubber gloves of 11 KV grade as per IS 4770-68.

Capacity 4.5 kg

Capacity 6 Kg.

Capacity 50 Lit.

22.5 Kg. CO2 Fire Extinguisher

Mani fold- Oxygen Manifold 8 + 8 cylinder banks complete with NRV, tail Pipes, Middle frame, Bottom Frame with CE marked,

Automatic Control Panel for Oxygen- 4 bar line pressure, 1000lpm as per as per Medical Device Directives

Emergency Oxygen Manifold- 02 + 02 Cylinder Emergency Manifold with complete regulator, NRV, tail pipes, Middle frame & Bottom frame,

Oxygen Flowmeter with humidifier Bottle, CE Marked,

Oxygen Gas outlets

Oxygen H.P. Rubber tube white color,

2+2 cylinder banks of Nitrous Oxide manifold complete with NRV, tail pipes, Middle frame & Bottom frame with CE marked,

Automatic Control Panel for N2O- 4 bar line pressure, 500 lpm as per as per Medical Device Directives (93/42/EEC)

Emergency N2O Manifold- 1X2 Cylinder Emergency Manifold with complete regulator, NRV, tail pipes, Middle frame & Bottom frame,

N2O Gas outlets (Imported)

N2O H.P. Rubber Tube Blue color, ,

Duplex Air Compressor- @ 8.5 bar pressure, 10 HP, two oil free reciprocating / Screw compressors One running and one standby, including Electrical work and civil work required for foundation.

Duplex Dryer & Filtration System as per specifications

Air Receiver tank of 1500 Ltr

MA-4 Gas outlets (Imported)

SA-7 Gas outlets (Imported)

MA-4 H.P. Rubber Tube Black color ,

Duplex Vacuum Pump- Air Cooled Reciprocating Pump having capacity of 60 CFM, 2 Nos. Vacuum Pumps One running and one standby including Electrical work and civil work required for foundation.

Duplex Bacterial Filtration as per HTM standards, one working and one standby

Vacuum Receiver Tank 1500 Ltr.

Vacuum outlets

Ward suction Unit with 600 ml Jar,

Theatre Suction Unit with 2nos. Jar of 2000 ml each,

Vacuum H.P antistatic tube yellow color,

Master Alarm,

Area line pressure alarm-4 Gases

Area line pressure alarm-3 Gases

Area line pressure alarm-2 Gases

3 gases

2 gases

12 mm (OD) x 0.7 mm Thickness

15 mm (OD) X 0.9 mm Thickness

22 mm (OD) X 0.9 mm Thickness

28 mm (OD) X 0.9 mm Thickness

42 mm (OD) X 1.2 mm Thickness

54 mm (OD) X 1.2 mm Thickness

Supplying and Installing Bed Head Panel of required length and width with Provision For Gas outlet as per requirement schedule.

Operation Suite - 5.5TR/1600CFM

24 Gauge 0.63 mm

Corded remote controller for AHU/Cassette/Hi Static Ductable

Cordless Remote Controller for Hi Wall

Description

Work to be done

Work done value

Description

Work to be done

Work done value

Description

Reason for Increasing of Cost

Amount As per TS

S.O.R. No.

L/Sand filling

kota flooring

one B/F soling

B/W Khoa

12mm(1:3)plaster

12mm(1:6)plaster

6mm(1:4)celling plaster

cutting length

kg/cum

cutting length

kg/cum

cutting length

kg/cum

cutting length

kg/cum

cutting length

kg/cum