Civil Maintenance including carpentry and PH works

Amount

Resizing & Refixing existing wooden doors for smooth operation. 1. Existing wooden shutter doors shall make floor touch free (to increase bottom clearance) by plane or cutting as approved manner. 2. If need, replacing existing bottom beading patti with new one, minimum 12 mm thick ( wooden beading if replaced wiil be measured under relevant Item) 3.The job is involved of dismantling/ taking out existing door shutter, un-screwing of hinges, after plane/fixing wooden beading, re-positioning the door shutter, re-fixing of door closer, handles if any etc. compete as directed by EIC. 4.Providing & fixing necessary wooden screws as required manner in position. 5.Adjustements of hinges if required. (Hinges if required replacing shall measured in relevant item) 6.Measurements: Each shutter of size of 1000 mm x 2100 mm shall be measured as one job.

Resizing of existing aluminium door shutter. 1. Existing aluminium framed swing doors shall make floor touch free (to increase bottom clearance) by resizing. 2. The job is involved of dismantling existing shutter totally including accessories/fittings; cutting of aluminium section as required; reassembling.3. Existing damaged/not reusable aluminium sections shall be replaced with new ones and the same will be measured under concerned items on weight basis. 4. Providing and fixing of s.s. tie rods having suitable nutt/bolts system at both ends of shutter if need. 5. Reshaping and re-fixing of existing board panel/glass sheets as required; 6. Re-erecting and repositioning the shutter as earlier. 7. Re-fixing of all fittings such as pull/push handle; hydraulic door closer; hinges; locking arrangement; tower bolts; 8. Replacing the existing damaged rubber gasket lining and aluminium clips with new ones 9. The contractor shall be provided the sundry materials such as rubber gaskets; screws, ms tie rods, Pivot top piece etc and no extra payment will be made for these. 10. If glass panels are broken during handling, the contractor shall replace the same at no extra cost. 11. Supply, inserting and fixing of hard wooden blocks of 150mm length in hinges, floor spring & door closer area of aluminium sections 11. Measurements: Each shutter up to size of 1000 mm x 2100 mm will be measured as one job

35 mm thick flush door Providing and fixing 35 mm thick flush door shutters conforming to IS : 2202 non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with internal teak wood lipping 25mm wide and fixing with 4 Nos of 125 mm long Stainless steel Hinges with S.S. wood screws complete.

Wooden moulded beading Providing and fixing 50 X 20 mm wooden moulded beading, using 2nd class teak wood to door, window and louver frames with iron screws, plugs and priming coat on unexposed surface complete.

Edge lipping with wooden battens Providing edge lipping with 2nd class teak wood battens 40x12 mm minimum depth on all edges of new Commercial flush door shutters. and replace edge lipping as required for existing old wooden shutters for repair works.

LOUVERED OPENING Providing & fixing LOUVERED OPENING of required size in door shutters including making the opening, providing & fixing teak wood louver blades with necessary teak wood frame work, beading & applying one coat of approved wood primer etc. complete.

Fixing /Replacing the damaged mesh Providing, Fixing /Replacing the damaged mesh of existing/ new doors louvers up to 0.3 Sqm with new aluminium mesh of 1.6mm thick of approved pattern & design in all type of doors including providing and fixing 25x12 mm second class teak wood beading on both side of shutters, screws, nails etc... complete and disposal of old scrap at designated point for further disposal as directed by EIC.

Vision panel Providing & Fixing / replacing vision panel not exceeding 0.1 sqm in all type of flush door including fixing 4 mm Clear Glass with necessary teak wood/ Aluminium/ms Beadings complete all as per specifications and asdirected by EIC. (Including cost of glass)

Providing and fixing IS:12817 marked stainless steel butt hinges of size 125 x 64 x 2.5 mm (heavy weight)" of approved make with suitable stainless steel screws etc. Complete as directed by Engineer-in-charge.

Providing and fixing stainless steel tower bolts of size 300 X 12 mm of approved make with necessary screws etc. all as per specifications and as per drawings.

Providing and fixing stainless steel tower bolts of size 200 X 12 mm with necessary screws etc.all as per specifications and as per drawings.

Providing and fixing stainless steel tower bolts of size 150 X 12 mm of approved make with necessary screws etc.all as per specifications and as per drawings.

Providing and fixing 6 Lever Mortice Lock of approved make suitable for aluminium sections.

Mortise latch Providing and fixing brass mortise latch and lock of approved make with 6 levers and a pair of lever Brass handles with necessary screws etc complete suitable for fixing in wooden / steel/ FRP/ doors as per specifications .

Universal hydraulic door closer Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer of approved make with necessary accessories and screws etc. in wooden doors / steel doors with necessary bolts & nuts complete as per specifications and as directed by the Engineer-in-charge.

Heavy duty door closer Providing supply and fixing Door Closer TS 71- DORMA- Std Arm.with necessary accessories and screws etc…. As per manufactures instruction, specifications and as directed by EIC.

Sliding back door closer Design, fabricating and fixing sliding back door closers for aluiminium framed door, clear opening of door-850mm, extension length maximum 1800 mm having speed adjustable, operating without battery or electricity including providing and fixing necessary fittings for sliding door shutter etc complete as directed by EIC and as per clause-25 of specifications.

S S Door handles Providing and fixing pair of S S Door handles- 22mm dia 250 mm long- KICH- 316 grade in Steel Doors/ wooden Doors including screws / bolts etc. all as per drawings and specifications complete.Sample shall be get approved by the Engineer-in-charge. ( Pair means 2 Nos, 1 set)

Offset type S S Door handles Providing and fixing pair of offset type S S Door handles- 22 mm dia 250 mm long suitable for aluminium doors including screws / bolts etc. all as per drawings and specifications complete.Sample shall be get approved by the Engineer-in-charge. ( Pair means 2 Nos, 1 set). sample shall got approved by EIC, before purchase of this item.

Aluminium Composite Metal Panel Designing, providing and fixing of 4 mm thick approved make and shade Aluminium Composite Metal Panel of approved make cladding at different locations including soffits of over-hangs but excluding aluminium frame work with grids filled in with weather silicon sealant as per the drawings. The ACM panel composition shall be of 0.5 mm thick PVDF coated aluminium sheet + 3 mm thick low density polyethelene virgin resin core + 0.5 mm thick polyester (PVDF) coated Aluminium sheet all complete as per approved shop drawings and specification (Aluminium frame work will be paid under reelevant item)

Aluminium grill Providng and fixing Aluminium Grill 10 mm thick "DECO GRILLE" make Model No. DG- 202 in natural Silver anodising of min 15 Micronswith a opening size of 60mm x 45mm and Minimum weight of 4.12 Kg/ Sq.M including providing anfd fixing Suitable 'F' / 'H' section outer frame and mullion fixing with screws complete all as per specifications and as directed at site by the Engineer-in-charge .Aluminium alloy shall be of 6063-T6 with yield strength of minimum 6.5 kg/ sq.mm. Item also includes providing Aluminium Grill 10 mm thick with colour anodised by the manufacturer (Champagne, black, Bronze, Gold colours) complete all as per specifications and as directed at site by the Engineer-in-charge

Colour anodised Aluminium sections Providing and fixing colour anodised Aluminium sections (Minimum anodizing thickness of 15 micron & colour shade as per approval of EIC) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealent etc. (fittings glazing and panelling shall be paid for separately)

Roller wheels Providing and fixing approved quality stain less steel body roller wheels of approved make for sliding shutters.

Star locks Providing and fixing approved quality and shape star locks cum handle of approved make for aluminium sliding shutters.

Stainless steel adjustable friction windows stays Providing and fixing stainless steel (SS 304 Grade) adjustable friction windows stays of size 710 X 19 mm of approved quality with necessary stainless steel screws to the side hung windows as per specifications and as directed by the Engineer-in-charge.

FRP door shutters Providing and fixing FRP door shutters flush door / panelled type with plain colour or wooden veneer finish of approved make, design & colour. made out of 1.5 mm thick FRP skin moulded over wooden frame work of 40 mm wide and required thickness wooden styles and minimum 100 mm wide lock rails and wooden blocks for door stoppers, tower bolts, baby latch, aldrop, handles etc. wherever required and core filled with Polyurethane Foam and fixing with 4 Nos 100 mm (ISI marked) stainless steel hinges with S.S. wood screws 35 mm thick panelled door type of approved colours including the cost of 100 mm ISI marked heavy quality stainless steel butt hinges with necessary screws.

Magnetic catcher Providing and fixing heavy duty magnetic catcher triple strip vertical type 40 mm of approved quality in cupboard / ward robe/FRP shutters, including fixing with necessary screws etc. complete .

Silicon sealent. Filling the gap between aluminium frame & adjacent RCC / Brick work / Stone work Joints by providing weather silicon sealant ( M/s Dow Corning or approved equilent for the specified purpose ) over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete Up to 5 mm depth and 5 mm width.

Clear float glass Providing and fixing glazing With clear float glass panes of 6.00 mm thickness in aluminium / wooden doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item)

Frosted glass Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item) With frosted glass panes of 6.00 mm thickness

Double action hydraulic floor spring Providing and fixing double action hydraulic floor spring of approved brand and manufacturer (conforming to relevant Indian Standard) for doors including cost of cutting floors as required, embedding in floors and cover plates with M.S pivot and single piece of M.S sheet outer box with slide plate etc. complete as per directions of Engineer-in-charge with brass cover plate

DORMA floor spring Providing and replacing existing double action hydraulic floor spring 'DORMA' make of specified Model No. BTS75 / 84/80 / 65 with top Pivots etc. or approved equivalent brand and manufacturer for wooden doors. including cost of cutting floors as required, embedding in floors and cover plates with Dorma make pivot and outer box with slide plate etc. complete as per directions of Engineer-in-Charge with stainless steel cover plate as approved by the Engineer -in-Charge.

Servicing of rolling shutters Servicing of the following type of rolling shutters of all sizes up to maximum size of 6m x 7m including scaffolding, by dismantling for over-hauling of individual parts for repairing and refixing after repaires i.e top hood shaft cage, shaft case, shaft brackets, springs, main curtain with lathe or mid bar type grills, wicket gate, side guides bottom rails, gear units, bearings, electric motors,starters and thoroughly cleaning all the components, adjusting the tensioning springs, if required overhauling or repairing shaft and gear units, re-conditioning end clips, re-aligning curtain ends, reconditioning dents if any, on the surface bottom rail and side guides, repairing the starter, inspecting, taking out and replacing the damaged or defective components (replacement of parts at extra rate is given under relevant item), ensuring proper locking arrangements from both side and out side including all welding, drilling, straightening , grinding, scaffolding, ladders, tools, tackles, with all consumables, such as lubricants, kerosene, grease etc. and shall hardware such as nuts, bolts, rivets, screws, washers, keys, etc. making good any damages to civil works,cleaning, oiling, greasing and demonstrating proper functioning of the shutters after each service such as nuts, bolts, rivets, screws, washers, keys, etc. and necessary scaffolding etc. all complete as per direction of Engineer-in-charge at site. a) Electrically operated type with lathes or grilled curtain, Mechanical Gear operated and Pull & Push type rolling shutters ( All types of Rolling Shutters) Note:1) Measurement will be done once only, for entire period of contract. 2) The measurement of Rolling shutters will be as per structural openings. 3) Rate includes fixing of rubber gasket min 6mm thick at bottom of rolling shutter on external shutters for prevent entry of reptiles.

Rolling shutters Supplying and fixing Rolling shutters of approved make as per ISI standards made out of required size of MS lathes 18 gauge interlocked together throughout entire length and jointed together at the end by end locks mounted on specially designed pipes shaft with brackets, side guides and arrangements for inside & outside locking with push and pull operation complete including the cost of providing and fixing necessary springs of required size and M. S top cover of required thickness for rolling shutters

Rolling shutters gear operated type with handles including top hood 0.90 mm thick

Extra over the cost of rolling shutters for providing wicket gate of specified size in the M.S rolling shutters including fixing with fixing arrangements, hinges, locking arrangements, frames etc. all as per standard specifications and as directed by the Engineer-in-chargecomplete.

Motorization of Existing and new rolling shutter Extra over the cost of rolling shutters for providing and fixing motorized arrangements for new rolling shutters. Item also includes cost of coversion of existing rolling shutters by changing its shaft alongwith suitable fittings nad accessories as suited to motorization work. motorization includes ( with remote & manual operation) including designing, control panels, limit switches,required wiring and cables from panel to motor and required size of shaft etc of approved make all as per standard specifications including commisioning and testing complete as directed by the Engineer-in-charge.(only power supply point will be provided)

For rolling shutters up to 15.00 sq.m opening area.

Providing, Supplying and replacing in position wherever required the following parts after removing the damaged old part carefully including all labour, taxes, duties, scaffolding, transport, welding, drilling, grinding, tools, tackles etc. and with applying one coat of primer wherever required, including transporting the dismantled M.S/ metal scrap and depositing at Trombay stores as directed by the Engineer-in-charge at site. Up to 5.00 M Height

G.I .lathe sections 75mm wide & 18g thick

M. S. bottom rails (pressed type 10G with locking arrangement, handles, etc. in both ends and sides.

Providing, supplying , fabricating and assembling Shaft asembly for Rolling shutters using Heavy M.S. Pipes, springs & ring pully complete including erection.

Providing, supplying and fixing M.S. guide channals with supports for existing rolling shutters complete including erection.

Providing, supplying and fixing Springs in Rolling shutter Shaft including necessary bolt& nuts complete including erection. For rolling shutter up to 5.00 metres height

Providing, supplying and fixing dead locks in rolling shutters necessary bolt & nuts complete including erection.

Providing, supplying and fixing gear box complete set with gear wheel, handle etc full assembly complete including erection.

Providing, supplying and fixing Side Brackets for Rolling Shutters Complete including erection.

Granite work Providing and fixing Minimum 17 mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut Granite of Jet Black colour for kitchen platforms, vanitiy counters, wash basin counters, door frames, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edges to give high gloss finish etc. complete at all levels. Note: cost moulding and polishing of granite edges as per required by EIC is included in the item.

Kotah stone flooring. Providing and laying minimum 25 mm thick uniform shade Kotah stone flooring over 20 mm thick (Avearge) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing in minimum three levels to obtain mirror polish complete with base cement mortar 1:4 (Using Coarse sand) all as per specifications, patterns and drawings complete.

Cleaning of Nahani / floor trap Opening of nahani trap and removing nahani trap jalli and cleaning the complete trap system and refixing the same with white cement etc. and as directed by Engineer in charge.

Cleaning of bottle traps Opening of bottle trap from its joint and cleaning the complete trap system and refitting,refixing same to sinks,wash basins etc. and as directed by EIC ( Note:- If bottle trap is found in unused condition it will be supplied by department at free of cost).

Removal of chokages in EWC/IWC/AIWC. Cleaning and removal chokages of sewarage wastes,muck,frozen sewage cakes etc. from EWC/IWC/AIWC manually, including cost of labour, tools like choke remover, trooly of sewage muck for disposal of designated place, all complete in all respect and as directed.

Cleaning secondary traps, Sewage inspection/ Storm water chambers. Cleaning and removal of sewage/drainage wastes, muck etc. from horizontal, inclined & vertical C.I./PVC/lines of all dia. ( burried/ exposed) ,secondary traps, Sewage inspection chambers, manhole chamber and all other drainage/ sewage disposal facilities from centralised chambers including all the external sewage / drainage lines of PRAFPUL building and its surrounding premises including all the sewage / drainage lines around pumpimg sump mechanically/ manually as desired and directed by department including cost of labour,tools,tackles,plants, machines,transportation all complete in all respect and as directed by Engineer in charge. Note. :- Water shall be supplied free of cost & the contractor has to make their own arrangements for the hose, pumps etc. for the flushing of all the chambers, open drains and coonecting sewage / rain water pipe lines to the chambers including trolly for disposal of garbage.

URINAL MAT Supplying and laying refresh Urinal screen mat of standard size for urinal pan of M/s ARNI make or approved etc complete as per specification. Note: 1 set=10pc

C.P. brass TOWEL RAIL/Hook Providing and fixing C.P brass towel rail of approved make 600 mm long or Hook of approved size and pattern complete fixed to walls with 30 mm CP brass screws with concealed fitting arrangement all as directed by the Engineer-in-charge.

C.P. brass Urinal spreader Providing and fixing 15 mm C.P brass urinal spreader size with 1/2" BSP thread and shapes, weighing not less than 60 gm of approved make and type.

Urinal flush cock Providing and fixing Brass 15 mm C.P presstomatic series auto shut urinal flush cock of approved make and quality and providing and fixng necessary piping arrangement for connecting to outlet system of above item.

SS grating 150 mm sqaure with frame Providing and fixing heavy quality stainless steel / C.P brass grating of approved equvalent make as specified for floor traps / nahani traps all as directed by the Engineer-in-charge

Mirror Providing and fixing 6 mm thick mirrors of size 600 x 450 mm of approved make with bevelled edges complete with 6 mm thick asbestos sheet back ground fixed to walls with C.P. brass screws and concealed washers complete. all as per specifications and as directed by the Engineer-in-charge .

Soap Dispenser Providing & fixing approved type heavy duty Euronics Liquid soap Dispenser-ES-04 with S.S brackets, cap etc. fixed to wall with C.P. brass screws, & screwed on to wooden rawl plugs etc. complete.

C.P. brass / copper inlet connection Providing and fixing CP brass / copper inlet connection pipes heavy quality suitable for hot and cold including CP brass unions and nuts 15 mm dia 600 mm long

C.P.brass pillar/Bib cock elbow operated Providing and fixing Heavy Quality C.P Brass Pillar/Bib cock ELBOW operated of "Jaquar " make and type as per specifications and as directed by the Project Engineer (Samples to be got approved by the Project Engineer)

Automatic Sensor Tap for wash basin Providing and fixing Heavy Quality C.P Brass Pillar Automatic Sensor Tap of "Euronics " make and type model ET01B as per specifications and as directed by the Project Engineer (Samples to be got approved by the Project Engineer)

Automatic Sensor Tap for wash sink Providing and fixing Heavy Quality C.P Brass Pillar Automatic Sensor Tap for wash sink of "Euronics " make and type model ET12L as per specifications and as directed by the Project Engineer (Samples to be got approved by the Project Engineer)

CP Brass Bottle trap Providing and fixing heavy quality CP brass bottle trap 31 / 32 mm of (Jaquar or Plato or approved equivalent make) single piece moulded with height of 270mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal,of Jaquar make for wash basins / urinal etc all as per specifications and directed by the Engineer in charge.

C.P. brass BIB cock Providing and fixing C.P brass bib cock of heavy quality of specified / approved make as per specifications and as directed by the Engineer-in-charge 15 mm dia bib cock of approved type and make .

2 in 1 bib cock and Angle cock Providing and fixing 15 mm C.P brass 2 in 1 bib cock and Angle cock combination of Heavy Quality of approved make as per specifications and as directed by the Engineer-in-charge

Pillar cock Providing and fixing 15 mm C.P brass pillar cock of heavy Quality of approved make and specied type as per specifications and as directed by the Engineer-in-charge.

Angle cock Providing and fixing C.P brass Angle cock of heavy quality of specified / approved make, for wash basin inlet / flush cistern etc. as per specifications and as directed by the Engineer-in-charge 15 mm n.b CP brass Angle cock of approved make

PVC inlet connection Providing and fixing PVC inlet connection pipes heavy quality suitable for hot and cold including CP brass unions and nuts 15 mm dia 600 mm long

Repairing of bibs tap/pillar tap/stop cock etc. Repairing of bibs tap/pillar tap/stop cock etc. by changing with the spindle, new washers etc. as per site requirement & directed by Engineer-In-Charge.

Supplying / fixing new sanitary fittings. Removing existing, damaged non workable sanitary fittings/ water supply fitting & replacing with new approved fittings as per site requirement & directed by Engineer-In-Charge.

Flush handles for slimeline or champion make & of required type.

Washers of flushing system of E.W.C.

Replacing inner fittings for flushing water for slimeline or champion make & of required type Flush tank

C P Brass health faucet Providing and fixing Heavy Quality C.P Brass Health Faucet with 1.50 metres flexible hose (Hand Shower) of "Jaquar" make with haevy CB brass wall brackets or approved equivalent make and type as per specifications and as directed by the Project Engineer (Samples to be got approved by the Project Engineer)

C.P. brass waste coupling Providing and fixing Heavy Quality C.P .Brass waste coupling of following dia for wash basin and sink, of approved make, size and quality all as directed complete with C.P Brass Waste coupling 32 mm Dia and minimum 79 mm length Half threaded or Full threaded as per requirement.

Wash basin Providing and fixing viterious China wash basin of approved make and colour with C.I. brackets, 15 m C.P. brass pillar tap of approved make,15 mm x 600mm long PVC Inlet connection, 32 mm heavy quality C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-charge White vitreous China wash basin size 630 x4 450 mm and equivalent sizes with single 15 mm C.P. brass pillar tap

Flushing cistern Providing and fixing PVC low level / high level flushing cistern 10 litre capacity of approved make in white colour with flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures etc. complete as per specifications and as directed by the Engineer-in-charge.

Plastic seat with lid Providing and fixing solid plastic seat of approved colour suitable to existing EWC with lid including CP brass / SS bolts, screws etc. for pedestal type W.C. pan complete as per specifications and as directed by the Engineer-in-charge

CPVC pipes for drainage Providing and fixing Chlorinated PVC (CPVC) pipes having thermal stability for hot & cold water supply (as ASTM Standard 2846 & SDR - 11 Grade) including all CPVC Plain & Brass threaded fittings, fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with CPVC Solvent cement & testing the joints complete all as per specifications, drawings and as directed by the Project Engineer 50 mm outer dia CPVC pipe (External) / open

Gate Valves Providing & fixing in position heavy pattern screw down gun metal gate valve with handles and wheels of approved make including testing for 10Kg/cm2 pressure with clean and potable water with a minimum testing duration of two hours etc.as per specification and as directed by the Engineer-in-charge

M.S.Galvanised pipes Providing , Laying , jointing, fixing and testing Heavy quality (C-Class) Galvanised Iron pipes and ISI marked fittings like, tees, elbows, bends, unions, nipples,reducers etc. as required for the work, including testing the pipes and fittings for 10.00 Kg / Sq.Cm hydralic pressure with a minimum period of two hours duration with clean water, including cutting , threading, jointing with hemp yarn, white lead, jointing Teflon tape, exposed / concealed by chasing walls and making good by filling with concrete 1:3:6, complete all as per specifications and drawings, including two coats of anti corrosive bitumastic paint for all concealed lines / two coats of synthetic enamel paint for all exposed lines all as directed by the Engineer-in-charge. Pipes with exclusive use of TATA make C-Class pipes.

15 mm dia G.I pipe Exclusive TATA Make

20 mm dia G.I pipe Exclusive TATA Make

25 mm n/b G.I pipe Exclusive TATA Make

40 mm dia G.I pipe

50 mm dia G.I pipe

80 mm dia G.I pipe

Rectify the pipe leakage Labour charges only for rectify the pipe leakage by fixing temporary clamps including preperation of clamps and gaskets for water lines in false ceilings / walls / service ducts, under ground services etc.. & joining the line by welding / threading etc... as per site requirement there after in G.I pipelines up to 100mm dia in RLG building.

Connection of distribution branch Making connection of distribution branch with G.I main of 25 to 40 mm/50 to 80 mm nominal bore by providing and fixing tee including cutting and threading the pipes etc. complete as per specifications and as directed by the Engineer-in-charge

G.I main of 25 to 40 mm nominal bore

G.I main of 50 to 80 mm nominal bore

Brass ball cock Providing and fixing brass ball cock (TECHNO make) or approved Equivalent heavy quality of following sizes with arm rod and Plastic Ball floats complete as per specifications and as directed by the Engineer-In-Charge.

15 mm Brass Ball Cock with PVC Ball Techno Make

25 mm Brass Ball Cock with PVC Ball Techno Make

15 mm thick internal plastering Providing 15 mm thick plastering using Ready mix internal plastering compound of approved make for internal faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning, scaffolding complete all as per specifications and as directed at site by the Engineer-in-charge

Structural repairs Providing structural repairs in old damaged concrete structures / surfaces with approved Polymer with following operations 1) Removal of loose/Spalled or damaged concrete by chipping and cleaning the concrete surface and reinforcement steel with wire brush and with water 2) Cleaning the re bars with Acetone for complete rust removal and washing with water to make the surface clean. 3) Applying protective coat / bond coat using polymer and cement in the proportion of 1; 1.5 (1 part of polymer and 1.5 parts of cement in synthetic enamal paint like consistancy with brush 4) Reinstate the area with polymer modified mortar in layers of maximum 20 mm with the proportion of Cement 50 Kg : washed and dried river sand 87.50 kg ; silica sand 37.50 Kg. mixed with 10 litres of Polymer (or 1 Kg cement : 1.75 kg washed and dried river sand ; 0.75 Kg silica sand : 200 ml polymer) 5) If thickness of repair exceeds 20mm , after every 20 mm thick repair, bond coat as per 2 above to be applied and further thick of repair to be continued for each layer. This work is inclusive of all materials, labour, complete all as directed at site using approved polymer suitable for structural repair shall be used) Note: Scaffolding will be paid separately under relevant item

Anchor Fastners Providing and Fixing Anchor Fastner of approved make including drilling in concrete as per requirement for fixing Eps or other structures all as specified by the manufacturer complete all as per specifications and drawings.

HST STUD Type M-20 X 170 mm Long

HST STUD Type M-12 X 145 mm Long

HST STUD Type M-10 X 130 mm Long

Structural repairing of foundation Structural repairing of foundations using following methods; 1. Cleaning the worn out portions of the RCC foundation with wire brush. 2. Cleaning the reinforcements properly with wire brush and applying a coat of Nitozinc Primer or equivalent to protect the reinforcements. 3.Drilling holes of 12mm dia and fixing shear connectors of 8mm or 10mm dia with Hilti Chemical anchors at a spacing of 150mm c/c. 4.Placing formwork in place in position so as to get a cover of minimum 50mm in the concrete. 5.Applying a polymer bond coat to the existing cleaned substrate and placing micro concrete (Rendroc RG(L) mixed with 6mm down aggregates or equivalent as per manufacturer’s specifications. 6. Curing the repaired area for a minimum of 7 days.

Fixing 8/10mm shear connectors for RCC member Drilling holes of 12mm dia and fixing shear connectors of 8mm or 10mm dia with Hilti Chemical anchors at a spacing of 150mm c/c for Structural repairing of foundations

Micro concreting Providing SFMC Micro concrete for strengthening of structural members including mixing, pouring, curing as per manufacturer specifications and as directed by the Engineer-in-charge Using SFMC with 50% Quartz aggregate by weight (Only SFMC consumed alone will be measured for payment)

Sealing the Expansion Joints Providing, supplying and sealing the Expansion Joints with elastomeric Polyurethane sealant (PU) sealant suitable for RCC Construction Joints of 'Hyperseal Expert 200' of M/S. ALCHEMICA construction Chemicals make or approved equivalent by removing the expansion joint sealent and cleaning the suface neatly, placing the backer rod wherever required in case of displacement or non-existing and filling elastomeric Polyurethane sealant (PU) up to 25 mm deep to the lines and levels complete all as per manufacturers specifications and as directed by the project engineer. 40 mm wide expansion Joints

50 mm thick cement concrete flooring Providing and laying 50 mm thick cement concrete flooring with concrete hardner topping under layer 38 mm thick cement concrete 1:2:4 and top layer 12 mm thick wearing surface with metallic floor hardner, cement being mixed with metallic floor hardner of approved quality and make in the ratio of 4:1 (4 cement and 1 metallic floor hardner) by weight and this cement hardner compound mixed with 6 mm down graded stone aggregate in the ratio of 1:2 by volume including providing and fixing 25 X 3 mm aluminium strip,This includes cost of cement slurry, finishing to the required finishing and cleaning neatly while handing over the areas etc. complete as per specifications and drawings.

Stainless Steel Work Providing and fixing hand rails/ SS drain gutter along with grating for fixing in floors using 304 grade Stainless Steel pipes of approved size and make and quality by welding, mirror / matt polishing, fixing at site etc. for balcony railing & staircases railing/ flooring work drains including special sections as per drawings, specifications. complete as directed by the Engineer-in-charge

Supply of suitable skilled and unskilled manpower Supply of suitable skilled and unskilled manpower with set of hand tools / drilling / cutting machines for miscellaneous jobs like carpentry maintenance, plumbing and masonry jobs. NOTE: Suitable manpower shall be deployed for the job assigned with safety gears as & whenever required. Man power shall be deployed as per requirement, including holidays & late working if required.

Supply of highly skilled Carpenter / plumber / mason.

Unskilled labours.

Dismantling old plaster Dismantling old plaster /pointing/ skirting carefully , raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 100 m lead

Removing wash basin. Removing hand wash basin carefully alongwith bottle trap ,stop cock, pillar tap,brackets & PVC connections carefully & stacking the the same as directed in Civil Maint.Stores of BARC Hospital .

Demolishing C.C / R.C.C works Demolishing C.C / R.C.C works by mechanical means and stock piling at designated locations carefully with out damaging adjacent structures and disposal of dismantled materials up to a lead of 100 m, stacking serviceable and unserviceable materials separately including cutting reinforcement bars all as directed at site.

Dismantling brick work Dismantling brick work in Cement mortar carefully without damaging adjacent structures including stacking of materials and dispoal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge

Dismantling doors, windows Dismantling doors, windows and clear storey openings (steel / wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100 m lead (full windows)

Area 3.00 Sq.M and below

Area beyond 3.00 Sq.M

Dismantling tile work Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 100 m lead For thickness of tiles above 10 mm and up to 25 mm

Dismantling Aluminium work Dismantling Aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplaus material and stacking of serviceable materials within 100 m lead as directed by the Engineer-in-charge

Dismantling waterline pipes Dismantling G.I pipes/ PVC pipes of all diameter external work including excavation and refilling trenches after taking out pipes manually / by mechanical means including stacking of pipes within 100 m lead as per direction of Engineer-in-charge

Dismantling of C.I pipes Dismantling the following dia of C.I pipes including excavation, taking out the pipes manually / by mechanical means, breaking lead caulked joints, melting of lead, making into blocks including stacking of pipes within a lead of 200 m as per direction of Engineer-in-charge75 mm Dia to 200 mm Dia C. I pipe

Dismantling flushing cistern Dismantling flushing cistern of any size including stacking of useful materials near the site and disposal of unserviceable materials within 100 m lead

M/S A.M CONSTRUCTIONS