SPECIAL REPAIRS TO BUILDING NO T-42 OR LIVING AT 71 ARTY BDE UNDER GE MISAMARI

Amount

Demolition of cement concrete (unreinforced) of any description in ground floor and pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling of Asbestos cement (corrugated ted, semi corrugated, etc.)/galvalume/fibre glass/CGI sheets in roof coverings complete all as specified and directed.

Dismantling of wall and ceiling board or insulation boards/slabs/blanckets/any thickness including cover fillets complete all as specified and directed.

Demolition of Brickwork build in cement mortar including all quoins, arches, pillars etc, of any descriptions, complete all as specified and directed.

Dismantling of boarding ,any description ,fixed in any position with nails etc complete all as specified and directed.

Dismantling of timber scantling 40 sqcm and over in section in any position unframed work complete all as specified and directed.

Dismantling of timber fillet, rails, posts, rafters, purlins etc under 40 sqcm and over in section in any position unframed work complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) area not exceeding 1.50 sqm each including iron mongeries complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) area exceeding 1.5 sqm but not exceeding 4.00 sqm each including iron mongeries complete all as specified and directed.

Taking down shutters of any description not exc1 sqm including iron mongries complete all as specified and directed.

Taking down shutters of any description exceeding 1sqm and not exceeding 2 sqm each including iron mongries complete all as specified and directed.

Refixing the shutters of any description in same opening exceeding 1sqm and not exceeding 2 sqm each complete all as specified and directed.

Taking down cement plaster on brick, concrete block wall or stone walls, etc., including raking out joints,hacking for key,scrubbing down with water etc compleate all as specified and directed.

Taking down cement plaster on lathing (other than wire-netting), without removing lathing (one side only measured in cases where both sides are plastered) complete all as specified and directed.

Supply and fix GI frame with powder coated work for seamless ceiling compresing premeter channel 0.55 mm thick with two unequal flange of 20 and 30 mm and web of 27 mm fixed to surroundings walls with GI wire 4.0 mm dia complete with suspenders complete all as specified and directed.

Supply and fix Non-Asbestos fibre cement building boards prepainted 4.00 mm thick, fixed to existing GI snap grid on ceiling complete all as specified and directed.

Material and labour for Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 completed all as specified and directed .

Material and labour for 15 mm thick rendering internal fair faces brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for 15 mm thick rendering in CM (1:4 ) on brick or concrete surface finished even and smooth without using extra cement mixed with water proofing compound @3% by weight of cement or as per manufactures instructions on internal wall surfaces of manholes/septic tanks etc. (Note: WPC shall be measured and paid separately under relevant item of Schedule 'A')

Supply only integral water proofing compound, conforming to IS-2465-1975 and as approved, complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Hacking out old broken glass (any thickness, size quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

Supply and fix factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc but divided into squares, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads etc for secuering glass excecter size of members of shutter as specified in SSR part-I, Sec -8 clause 8.20 (a) complete all as specified and directed.

Supply and fix factory made 30 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc but divided into squares, edges framing plain, chamfered or rounded, fitted with cut and mitred beads etc for secuering glass excecter size of members of shutter as specified in SSR part-I, Sec -8 clause 8.20 (a) complete all as specified and directed.

Supply and fix Flush shutters 30 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to wooden chowkats, complete all as specified and directed.

Supply and fix 2nd class hard wood plain solid straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. (Species :TitaChampa/Bonsum/Hollok or equivelent).

Supply and fix 100mm size mild steel butt hinges medium weight cold rolled and fixed complete all as specified and directed. Make :- Crown/Nulite/Mepro/Argent/Classic/Elite or equivalent ISI Marked fitting to be used.

Supply and fix 75 mm size mild steel butt hinges medium weight cold rolled and fixed complete all as specified and directed. Make :- Crown/Nulite/Mepro/Argent/Classic/Elite or equivalent ISI Marked fitting to be used.

Supply and fix 50 mm size mild steel butt hinges medium weight cold rolled and fixed complete all as specified and directed. Make :- Crown/Nulite/Mepro/Argent/Classic/Elite or equivalent ISI Marked fitting to be used.

Material and labour for second class hard wood scantlings wrought in framed work fixed with nails complete all as specified and directed.

Fixing Only for second class hard wood scantlings wrought in framed work fixed with nails complete all as specified and directed.

Supply and fix 2nd class hard wood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n exc 200 cu. cm each

Material and labour for 2nd class hard wood plain fillets, square, rectangular or triangular in section exc. 13 sqcm but n.exc 25 sqcm, clean sawn secured with nails or brads complete all as specified and directed

Supply and fix 2nd class hardwood 20 mm as in boarding plained one side fixed with nails in any situation and butt joint, etc complete all as specified and directed.

Supply and fix Mild steel barrel tower blots 150 mm long , stove enamelled black, with bright bolt and fixed complete all as specified and directed. Make :- Crown/Nulite/Mepro/Argent/Classic/Elite or equivalent ISI Marked fitting to be used.

Supply and fix Mild steel barrel tower blots 200 mm long , stove enamelled black, with bright bolt and fixed complete all as specified and directed. Make :- Crown/Nulite/Mepro/Argent/Classic/Elite or equivalent ISI Marked fitting to be used.

Supply and fixing for 300 mm mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts turn on bolt plate two on staple plate and fixed complete all as specified and directed. Make :- Crown/Nulite/Mepro/Argent/Classic/Elite or equivalent ISI Marked fitting to be used.

Supply and fixing 100mm size Mild steel pressed handles ,oval type,stove enamelled black complete all as specified and directed. Make :- Crown/Nulite/Mepro/Argent/Classic/Elite or equivalent ISI Marked fitting to be used.

Supply and fixing 150mm size Mild steel pressed handles ,oval type,stove enamelled black complete all as specified and directed. Make :- Crown/Nulite/Mepro/Argent/Classic/Elite or equivalent ISI Marked fitting to be used.

Supply and fixing 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply and fix Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with MS wire staple etc complete all as specified and directed.

Supply and fix in repair Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm etc complete all as specified and directed.

Supply and fix 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5 Sq.m in each pane including oil putty and bedding complete fitting complete all as specified and directed. Make :- Saint Gobin/Modi float/Triveni float glass/hindustan pilkington or equivalent ISI Marked

Material and labour for 75mm thick PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in path/plinth protection/hard standing complete all as specified and directed.

Material and labour for 15 mm thick screed bed in cement mortar 1:6 for laying floor tiles complete all as specified and directed.

Material and labour for 10mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finished rough to receive tiles as in skirting, dados etc complete all as specified and directed

Material and labour for durastone heavy duty tiles of size 300x300x10 mm thick as in footpath set and joited in neat cement slurry and pointed in grey cement complete all as specified and directed

Material and labour for preparing surfaces of wood and wood based mateinals, backs of chowkats etc, area tarred exceeding 0.1sqm but not exceeding 0.5sqm each with tar or coal tar black paint complete all as specified and directed.

Supply and fix for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

Supply and fix for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

Material and labour for 6 mm thick plywood grade BWR type BB fixed with nails to timber frame work etc complete all as specified and directed. Make :- Kitply/Mysore chip board/Century plywood/ Green Ply/Unipac,yamuna ngr /Duroboard, sharda plywood or equivelent to ISI Markd.

Supply and fix Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates of grade Fe-410 W (gde-E-250) Quality A complete all as specified and directed.

Fixing only Rolled sections as in purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed

Supply and fix mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm and n exc 10 cm long and dia of neck 12 mm complete all as specified and directed.

Supply and fix wire netting 0.9 mm dia and 12 mm mesh lathing to wood or metal studding post etc in walls.

Material and labour for 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone agg as in floors complete all as specified and directed.

Material and labour for Non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified and directed. Make :- Somany/Kajaria/Orient/Johnson/Nitco/Sunheart/Sunsine Tiles co pvt ltd or equivelent.

Material and labour for glazed ceramic coloured tiles of size (200x100mm) 6 x 7mm thick on vertical surfaces such as in skirting, dados set and jointed in neat cement slurry and pointed in coloured cement to match. Make :- Somany/Kajaria/Orient/Johnson/Nitco/Sunheart/Sunsine Tiles co pvt ltd or equivelent.

Supply and fix bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; will ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe410-0 or Fe 310-0 complete all as specified and directed.

Material and labour for preparation of plywood and wood based material over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. Make:- Berger Luxol HI Gloss/Borolac (J&N) /Nerolac/Asian paints Apcolite/Superlac (Shalimar)/Dulux or equivalent.

Material and labour for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed. Make:- Berger Luxol HI Gloss/Borolac (J&N) /Nerolac/Asian paints Apcolite/Superlac (Shalimar)/Dulux or equivalent.

Material and labour for preparation of plywood and wood based material not exc 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. Make:- Berger Luxol HI Gloss/Borolac (J&N) /Nerolac/Asian paints Apcolite/Superlac (Shalimar)/Dulux or equivalent.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer including chalk whitening etc complete all as specified and directed Make :-Snowcem/Asian guttu/Duracem/Acrocem/Ecocem/Rubicem (J&N) or equivelent.

Material and labour applying for two coat of cement based paint over a coat of chalk whiting on new plastered surfaces including preparation of new wall surface complete all as specified and directed.

Material and labour for preparation of old distempered surface of wall incl washing down and stoping of distempered surface and appliying one coat of distemper oil emulsion all as specified and directed Make :-Snowcem/Asian guttu/Duracem/Acrocem/Ecocem/Rubicem (J&N) or equivelent.

Material and labour for preparation of old treatment on external surfaces of walls and washing down with water to receive the surface and applying one coat of cement base paint (colour and tint as approved) on walls etc complete all as specified and directed.

Material and labour for applying two coats of synthetic enamel paint over a coat of red oxide primer to steel and iron surfaces of any description over 10 cm in width or girth not otherwise described including preparation of new steel surfaces complete all as specified and directed. Make:- Berger Luxol HI Gloss/Borolac (J&N) /Nerolac/Asian paints Apcolite/Superlac (Shalimar)/Dulux or equivalent.

Dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Material and labour for Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound, Grade `A' complete all as specified and directed.

Preparing surfaces of wood or wood based materials new or old of any description and girth not otherwise described and treated with two coats of creosote oil etc complete

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder,ceiling roses, regulators, switch socket outlet, bulk head fittings, tube light fittings etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed.

Taking down carefully by unscrewing from board/outlet boxes, fittings and fixture such as main switches & DBs of any size and any capacity and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed.

Taking down sub main wiring/service cable of any type and any size and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed.

Taking down UG cable of any type and any size and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed.

Material and Labour for Point wiring with 1.50 sq mm (nominal area), two single core PVC insulated unsheathed , 1100 volts grade, multi-stranded copper conductor FRLS Grade, in and including PVC casing capping with accessories with teak wood boxes and 3 mm thick plastic laminated sheet top cover size with all fittings and accessories including MS pressed steel terminal boxes of 1.22 mm thick of suitable size duly painted with red oxide metal primer for housing/mounting brackets switches,sockets etc, including PVC insulated unsheathed single core multi-stranded copper conductor FRLS Grade cable of size 1.5 sq mm green in colour as earth continuity conductor connected to common earth dolly for one light/point controlled by one way switch complete all as specified and directed.

All as per item No 75 here-in-before but for one ceiling fan/Exhaust fan point controlled by one switch.

All as per item No 75 here-in-before but for one 3 Pin 5 Amp switch outlet controled by one switch on the same board complete all as specified and directed

All as per item No 75 here-in-before but for one 5 Amp socket outlet three pin controled by one switch on independent board complete all as specified and directed

All as per item No 75 here-in-before but for 3 pin 15 Amps socket outlet independant board drawn from DB and including PVC insulated multi stranded copper conductor 2.5 sqmm 1100 volts FRLS grade and earth continuity wire 1.5 sqmm PVC insulated copper wire (Green) FRLS grade including PVC casing and capping complete all as specified and directed..

Supply and fix switch piano flush type single pole one way 5 Amp 240 volts complete all as specified and directed

Supply and fix switch socket combination 2 in 1 , 3 pin 5 Amps flush type 240 volts complete all as specified and directed .

Supply and fix switch socket combination multipurpose 2/3 pin , 5 Amps flush type 240 volts complete all as specified and directed .

Supply and fix switch socket combination multipurpose 5/15 A flush type, 2 in 1, 240 volts complete all as specified and directed.

Supply and fix ceiling rose surface bakelite 65 x 50 mm two to three terminals AC 230 volts complete all as specified and directed.

Supply and fix ceiling fan regulator step type, flush type heavy duty suitable to work on 230 volts AC supply complete all as specified and directed.

Supply and fix lamp holder, insulated body, with back plate for angular batten fittings with one PVC block of size 75mmX75mm for mounting the fitting including 10 watt LED lamp cat no LHLDERHEMD8X010 MAKE HAVELLS or equivalent in Bajaj or Crompton complete all as specified and directed.

Supply and fix sheet metal enclosures for DBs (Double door type) when MCB TPN 4 way with 200 Amps rated bus bar single pole and neutral fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection complete all as specified and directed.

Supply and fix sheet metal enclosures for DBs (Double door type) when MCBs to be used 240 volts 8 way with 200 Amps rated bus bar single pole and neutral fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection complete all as specified and directed.

Supply and fix MCB four pole 40/63 Amp 415 volts, confirm to IS /IEC 60898 breaking capacity of 10 KA, C - curve complete all as specified and directed. Make :- L&T cat No BB40630C or equivalent Havells/Bajaj/Crompton

Supply and fix MCB Double pole 32 Amp 240/415 volts, confirm to IS /IEC 60898 breaking capacity of 10 KA, C-curve complete all as specified and directed. Make :- L&T cat No BB20320C or equivalent of Havells/Legrand

Supply and fix MCB SP 6-32 Amp 240 volts,50 HZ , confirm to IS /IEC 60898 breaking capacity of 10 KA, C-curve complete all as specified and directed. Make :- L&T cat No BB10320C or equivalent Havells/Legrand

Supply and fix wall mounted LED 18 watts, box type (decorative) light fitting, 230 volt with extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver connector block etc with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from celling rose to fitting including LED tube 4' x 18 watts complete all as directed by Engineer-in-Charge. Make :- Havells, Cat part No LHLDCLXEUL83018, LHFYBPNIA1W022 or equivalent in Bajaj & Crompton.

Supply and fix Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic drive of capacity 25 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complet all as directed by Engineer-in- Charge. Make Havells, Cat No LHETBXU7PA6S025, Bajaj & Crompton.

Supply and fix sub main wiring with two single runs of single core 6 Sqmm PVC insulated and unsheathed cable with multi stranded copper conductor FRLS grade on surface or recessed or drawn in PVC casing capping along with 4.00 Sqmm single core copper conductor multi stranded cable as earth continuity conductor complete all as specified and as directed. (Note: One run of PVC casing capping ,one run of 4 sqmm earth wire and 2 Run of 6 sqmm cable shall be measured as one run.)

Taking down ceiling fan of any sweep, keeping with safe custody and hanging/fixed in repair the same with replacement of UNSV PVC insulated PVC sheathed 3 corte multistandard copper conductor cable of size 23/0.193 from ceiling rose to fan terminal conductor complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for foundation and getting out in soft/loose soil complete all as specified and directed.

Returning,filling in including spreading leveling watering and well ramming in layers not exceeding 25 cm thick, in hard/dense soil complete all as specified and directed.

Removal of surplus soil to a distance not exceeding 50 Metre and depositing where directed at a level not exceeding 1.5 Metre above the starting point complete all as specified and directed..

Supply and spread fine dry river sand for cable cushioning in trenches complete all as specified and directed. (Note:- Sand shall be measured and paid puneshed thickness)

Supplying and laying well brunt brick,locally available best quality (Sub class 'B' bricks) laid in trenches perpendicular to UG cable protections complete all as specified and directed

Supplying, laying, testing and commissioning LT UG Cable of size 4 Core 16 Sqmm laid in trences/floor/on wall/service connection PVC insulated, sheathing and armd 1100 volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary lugs after cutting to required length complete all as specified and directed

Supply and fix GI tubing 40 mm dia ' Light grade', in trench or on wall for the protection of UG cable complete all as specified and directed. Make :- Jindal/TATA/Prakash Surya/Swastik/Appolo/BST/Kalinga/Goodluck or equivelent.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron. Earth strip protected by GI pipe 15 mm bore(medium grade) and connected to main switch board or main control board as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm C/C with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete all as directed by Engineer In Charge.

MS Awash Ghosh and Brothers

M/S Mahabir Traders

Sunrise Enterprise

M/S Himalayan Trading Co