SPECIAL REPAIR TO MAIN PUMP HOUSE AND CERTAIN OVERHEAD TANK UNDER ZONE B AREA UNDER AGE B/R-II OF GE (EAST) JABALPUR

Amount

SCHEDULE FOR "UNRESTRICTED AREA"

Dismantling of plain or corrugated steel sheeting any gauge ,thickness in roof coverings complete all as specified and directed.

Demolition of cement concrete (un reinforced) in ground floor and paving n.exc 15 cm thick below or above ground level complete all as specified and directed.

Demoliton of brick work built in CM including all quoins arches, pillars etc complete all as specified and directed.

M&L Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in CM (1:6) complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in foundation, sub base, filling and mass concrete complete all as specified and directed.

M&L RCC M-30 design mix as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M& L RCC M-30 design mix as in walls, retaining walls, basement walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work, vertical or to batter complete all as specified and directed.

Use and waste of formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and directed.

M&L RCC M-30 design mix as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

M&L Mild Steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking , bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild Steel TMT bars 8mm dia cut to length, bent to shape reqd including cranking bending, spirally for hooping for columns, hooking ends and binding with mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for 15 mm thick rendering in CM(1:4) on concrete surfaces of internal walls finished even and smooth without using extra cement mixed with water proofing compound @ 3 % by weight of cement or as per manufacturer instructions while the concrete is green complete all as specified and directed. Note : WPC shall be paid measured and paid separately.

Supply only water proofing compound complete all as specified and directed.

Taking down cement plaster of any description including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L rendering 15 mm thick in CM 1:4 on brick work or concrete wall surfaces finished even and smooth surfaces using without extra cement complete all as specified and directed.

M&L preparing the newly plastered or unplastered surfaces and applying two coats of cement based paint on walls complete all as specified and directed.

Dismantling structural steel work including doors, gates, wind ties but excluding framed truss etc complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-290 Gde E- 165 complete all as specified and directed.

S&F 1mm thick Mild steel plain black sheeting in wall cladding , covering to steel gates and similar works, cut to size,holes,punched, including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams , including bending or turning up mitred angles etc as required complete all as specified and directed.

Taking down chowkhats or frames n.exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

M&L Rolled Mild Steel section as in Rafter purline , using MS angle FI or hollow square section etc including cutting welding, nut, bolt, with angle cleats or other connecting plates conforming to Fe-410-00 (Gde-E-250 quality 'B') etc complete all as specified and directed.

S&F (Factory made) steel ventilators with top hung shutter including hinges steel peg stay complete all as specified and directed.

S&F steel windows with side hung shutters including projection type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.48 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks ,or galvanised wire complete all as specified and directed.

M&L Sheet glass ordinary quality and glazing with oil putty in square but exc. 0.5 sqm in each pane 3 mm thick complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F frame work such as grills, grating etc with ends of bars shouldered and or rivetted or forged into spikes, framed guard bars, barred iron doors,ladders etc and similar wks conforming to Fe-410-0 or Fe-310-0 complete all as specified and directed.

Dismantling stone slabs, floor or wall tiles including CM bedding and removing the rubbish to a distance n. exc 100m at low lying area complete all as specified and directed.

M&L Glazed ceramic coloured & designer tiles in vertical surfaces 350x250/450x350 7to 8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 thick rendering in CM (1:4) finished rough to receive tiles etc as per manufacturer instruction complete all as specified and directed.

S&F Rubber moulded casted Machine pressed precast concrete inter locking Paver Block any shape and size Conf. to IS:15658-2006 of 60mm thick M-35 grade with Grey cement and pigment over and including 25mm thick sand cushioning complete all as specified and directed.

S&F Precast( kerb stone) concrete block masonry of PCC (1:3:6) type C1 using 20mm graded aggregate and set in CM (1:6) complete (Machine pressed) to match the interlocking tile etc with and including necessary excavation, use & waste of form work for plain fair faces of concrete complete all as specified.

M&L 75mm thick cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as in floors/ plinth protection etc finished even and fair complete all as specified and directed.

M&L one coat of synthetic enamel paint on steel & iron surfaces of any description, not otherwise described over 10cm width or girth including preparation of old painted surface complete all as specified and directed.

M&L two coats of synthetic enamel paint over a coat of primer on steel and iron surfaces of any description, not otherwise described over 10cm width or girth including preparation of new steel surface complete all as specified and directed.

M&L for Dewatering of existing water tank rest at ground cleaning the inside surface of the tank by scraping down wall & bottom surfaces using steel wire brushes to remove all deposition / fungus, other micro - organisms etc. Using light hammer & wire brushes, taking out and removing sediment loose dirt/mud sludge, vegetation and other foreign materials completely from the tank disposal of all the waste/ spoil to out of MD land at a place as specified by local bodies and washing repeatedly the inside surface of tank with water and washing with rebukes solution and clean water thoroughly complete all as specified and directed. Note : Tank capacity 1.00 Lakh Gallon

M&L Dewatering of existing over head water cleaning the inside surface of the tank by scraping down wall & bottom surface using steel wire brushes to remove all deposition / fungus, other micro - organisms etc. Using light hammer & wire brushes, taking out and removing sediment loose dirt/mud sludge, vegetation and other foreign materials completely from the tank disposal of all the waste/ spoil to out of MD land at a place as specified by local bodies and washing repeatedly the inside surface of tank with water and washing with rebukes solution and clean water thoroughly complete all as specified and directed. Note : Tank capacity 1.00 Lakh Gallon

M&L Dewatering of existing water tank rest at ground cleaning the inside surface of the tank by scraping down wall & bottom surface using steel wire brushes to remove all deposition / fungus, other micro - organisms etc. Using light hammer & wire brushes, taking out and removing sediment loose dirt/mud sludge, vegetation and other foreign materials completely from the tank disposal of all the waste/ spoil to out of MD land at a place as specified by local bodies and washing repeatedly the inside surface of tank with water and washing with rebukes solution and clean water thoroughly complete all as specified and directed. Note : Tank capacity 25000 Gallon

M&L Dewatering of existing over head water cleaning the inside surface of the tank by scraping down wall & bottom surface using steel wire brushes to remove all deposition / fungus, other micro - organisms etc. Using light hammer & wire brushes, taking out and removing sediment loose dirt/mud sludge, vegetation and other foreign materials completely from the tank disposal of all the waste/ spoil to out of MD land at a place as specified by local bodies and washing repeatedly the inside surface of tank with water and washing with rebukes solution and clean water thoroughly complete all as specified and directed. Note :Tank capacity 50000 Gallon

Dismantling / taking down old existing unserviceable cement plaster loose / unsound weaken cement conrete of any description and in any position from existiing external / internal surface of RCC OGT / sump / wall / roof / beams / columns / RCC, average depth 15 mm (at any staging) with power dirven of pneumatic chisel and disposal of unservicable material debries and rubbish outside MD land at a place as specified by local bodies including cutting of all edges, making square shoulders of the cavities, roughening the smooth surfaces, srapping out / removing corrosion all loose / scale / rust etc from the visible reinforcement by applying rust remover maxcure RR of Thermax Ltd or equivalent of Chemco system/Wbac chemicals and cleaning the steel reinforcement properly and then applying single component cementiotious corrosion inhibting primer for steel reinforcement Mucis PROTEZIONE FERRO NONO of Thermax Ltd or equivalent of Chemco systerm/ Webac chemicals on visible reiforcement surfaces to form a continuous fill not less than 1 mm thick all as specified and directed Note: Quoted rate shall be deemed to be inclusive of materials all labours, tools and plants, scaffolding and working upto hieght 25 mtr etc complete all as specified and directed. Note : Adoption of necessary safety arrangement like safety belts ropes, helmets netting etc which are required for safety of worker working at height exceeding 3 mtr shall be mandatory and deemed to be inclusive in quoted rates

Providing & laying of 25 mm thick Emaco S88 CT or equivalent fibre reinforced pre-packed Polymer Modified cementitous Mortar on the sound substrate and making the surface is original shape. Cure it for 3 days complete all as specified and directed.

M&L Pidifin 2K two component Acrylic polymer cementitious water proof elastomeric cement based coating food grade mix to form uniform slurry and apply with paint brush in two coat than laying second layer of fiber glass mesh cloth and first coat is green with overlap to joints of Fibre cloth should not be less than 10 cm, then finally apply third layer mix by brush to entire surface of container covering o.6-0.75sqm /lg at 1mm thickness in two coat depending on the level of substrate. Cure its for 3 days including necessary steel scaffolding steel platform and proper supporting by steel prop etc complete all as specified and directed Make : Pidilite Industries Ltd /Fosroc India Ltd /IWL India Ltd. Note : (a) Qoted rate shall be deemed to be inclusive of materials all labours. tools and plants scaffolding and working upto height 25mtr etc. BASF/T-Guard ANTC of make Thermax. (b) Adoption of necessary safety arrangement like safely belts ropes, helmets netting etc which are required for safety of works working at height exceeding 3 mtr shall be mandatory and deemed to be inclusive in quoted rates.

Providing and application of 10mm thick plaster in CM of (1:4) cement:sand plaster admixed with inegral water proofing compound Rheomac 707 @ 1000ml per bag of cement over the inside / out side of dome area all in complete including bonding coat of Polyalk EP and cement slury to the plaster area or as per the direction complete all as specified and directed.

Providing and application of primer and two coats of non-algai, non fugai, anti corbonation and hygienic coating of SUNEXT -8 MAKE OF Sunanda sp. Coating Ltd to entire interior area of tank as per instruction of Engineer in Charge, including additional scaffolding/ plateform, steel prop etc. to full height of tank complete all as specified and directed.

M&L repair to cracks and damaged existing surfaces of RCC OHT / column / beam etc(Approx height 4 to 25 M from groiund level) by structural strengthening using epoxy injection grouting treatment to voids and honey combed areq where nozzels fixed with low viscous non shrink. high strength epoxy grout concessive complete all as specified and directed. Make : Pidilite Industry/ Fosroc India Ltd /IWL india Ltd or equivalent. Notes : (a) Fixing of 12mm aluminium pacers/ GI nozzles in zig-zag gashion not more than 30-50 cm c/c on RCC surfaces on all directions as required after drilling holes in concrete. fixing GI nozzles with fast setting mortar and covering with renderoc plug . The size of holes shall be 12 mm dia and 75 mm in depth. (b) Epoxy injection grouting concessive 1315 of BASF in equivalent @ 150-200ml in each hole through pressure gun / pump at 5 to 7 kg /cm2 after mixing design and hardner to the extent till refuse to accept further grout complete. (c) Cutting and flushing of nozzles with surface after completing grouting and sealing the nozzles with CM (1:1) and preparing the surface to match with the existing surfaces all as directed. (d) Quoted rate shall deemed to be inclusive of materials all labours, tools and plants, scaffolding and working upto height 25 mtr etc. (e) Adoption of necessary safety arrangement like safely belts ropes, helmets netting etc which are required for safety of works working at height exceeding 3 mtr shall be mandatory and deemed to be inclusive in quoted rates.

Excavating in trenches, n exc 1.5m wide & n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan & getting out in soft/loose soil complete all as specified and directed.

M&L moorum / red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled & rammed including watering complete all as specified and directed.

M&L RCC M-25 design mix using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L RCC M-25 design mix using 20 mm graded stone aggregate as in walls, retaining walls, basement walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

M&L 15 mm thick rendering CM(1:4) on concrete surfaces of internal walls finished even and smooth without using extra cement using water proofing compound @ 3 % by weight of cement or as per manufacturer instructions while the concrete is green complete all as specified and directed. Note : WPC shall be measured and paid separately .

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping srew complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping srew complete all as specified and directed.

M&L providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

M&L Forming 12 mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘B’ complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for RCC M-25 as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Use and waste of formwork to sides of pillars,posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L Mild steel TMT bars 8 mm dia to 10mm dia as in stirrups , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Excavating in post holes (or similar holes) in hard/dense soil each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed

M&L cement concrete 1:3:6 using 40mm graded stone aggregate as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed

M&L cement concrete 1:4:8, type D2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed

Supply only chain link MS galvanisd fencing, any size or type complete all as specified and directed. Note : Weight of chain link shall be assesed by BOO conveyed by GE.

Fixing only chain link fencing of mesh size 75x75mm including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed

S&F mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting,welding etc., and similar work conforming to Fe- 290 Gde E-165 complete all as specified and directed

S&F mild steel bolt machine made with hexagonal or square heads at one end and screwed the other or screwed both ends each screwed and to be fitted with washers and one hexagonal or square but length of bolt exc 5 cms but n.exc 10cm long dia shall be of 5 to 10mm dia complete all as specified and directed

M&L mild steel round bars 10mm dia and over, cut to length, bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (Annealed) not less than 0.9mm dia conforming to Gde E-250 or Gde E 165 complete all as specified and directed

M&L cement concrete 1:4:8 type D2 by using 40mm graded stone aggregate as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed

M&L Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note : (a) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid separately (b) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M&L Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed Note: Stainless steel butt hinges and necessary S S screws shall be measured and paid separately.

S&F precoated steel window Rolled framed GI Section ECO 4000 (Openable double rebate window) Providing and fixing of single rebate openable/fixed windows made of galvanized steel colour coated/powder coated (base steel as per IS 513 of “D" quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 microns, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 48 x 50 mm, centre mullion section 48 x 50 mm, shutter section 47 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consists rebate for glazed shutter with a 20 mm provision for guard bars/grills and the sections cut to length mitre joined with corner bracket, centre mullion fixed with mullion cap, handle, stay, 2 nos. SS( stainless steel) heavy duty pivot hinges per shutter and window fitted with 5mm thick plain float glass with EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing frames in concrete/masonry wall by means of self expanding screws, Including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. complete all as specified and directed

S&F Aluminium handles 150mm size, cast type, anodised complete all as specified and directed

S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section complete all as specified and directed

M&L Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.in hard and dense soil complete all as specified and directed

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed

Note : Quoted rate should deemed to be be included of required scafolding for any height etc.

SCHEDULE FOR "RESTRICTED AREA"

Dismantling of asbestos cement (corrugated, semi corrugated etc ) sheets in roof coverings complete all as specified and directed

Dismantling timber scantling (framed work ) 40 sq.cm and over in section, in any position etc complete all as specified and directed

M&L Rolled Mild Steel section as in Rafter purline , using MS angle FI or hollow square section etc including cutting welding, nut, bolt, with angle cleats or other connecting plates conforming to Fe-410-00 (Gde-E-250 quality 'B') etc complete all as specified and directed

S&F Rolled mild steel section roof trusses (framed), trussed purlins crane gantries, rails & fastenings & heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. GDE Fe410-0 or Fe 310-O complete all as specified and directed

M&L one coat of synthetic enamel paint on steel & iron surfaces of any description, not otherwise described over 10cm width or girth including preparation of old painted surface complete all as specified and directed.

M&L two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise described over 10cm width or girth including preparation of new steel surface complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping srew complete all as specified and directed

S&F pre-painted galvalume aluminum zinc coating GI based plain sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping srew complete all as specified and directed

Taking down chowkhat with shutter but exc 1.5 sqm but n.exc 4.0 sqm each complete all as specified and directed

Taking down Chowkats or frames exc 1.5 sq. m but n exc 4 sq m each with shutters (without taking off shutters from the frames) complete all as specified and directed

M&L Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed Note :- (a) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid separately. (b) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M&L Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed Note: Stainless steel butt hinges and necessary S S screws shall be measured and paid separately

S&F precoated steel window Rolled framed GI Section ECO 4000 (Openable double rebate window) Providing and fixing of single rebate openable/fixed windows made of galvanized steel colour coated/powder coated (base steel as per IS 513 of “D" quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 microns, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 48 x 50 mm, centre mullion section 48 x 50 mm, shutter section 47 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consists rebate for glazed shutter with a 20 mm provision for guard bars/grills and the sections cut to length mitre joined with corner bracket, centre mullion fixed with mullion cap, handle, stay, 2 nos. SS( stainless steel) heavy duty pivot hinges per shutter and window fitted with 5mm thick plain float glass with EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing frames in concrete/masonry wall by means of self expanding screws, Including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. complete all as specified and directed

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm with stainless steel wire staples complete all as specified and directed

S&F Aluminium handles 150mm size, cast type, anodised complete all as specified and directed

S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section complete all as specified and directed

Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed complete all as specified and directed

S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed

M&L for 75mm thick cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as in floors/ plinth protection etc finished even and fair complete all as specified and directed

Demolition of cement concrete (un reinforced) in ground floor and paving n. exc 15 cm thick below or above ground level complete all as specified and directed

Note : Quoted rate should deemed to be be included of required scafolding for any height etc.

Schedule of credit amount of Rs. 31570.00 to be deducted during AOC.

RAVINDRA ELECTRICAL (BID ID -3342931)

SHIVA ENTERPRISES (BID ID -3343195)

R R VISHWAKARMA CONSTRUCTION CO (BID ID -3341613)

TRISHLA CONSTRUCTIONS (BID ID -3343328)

Hemant Associate (BID ID -3341344)

deepak kumar vishwakarma (BID ID -3340371)

Shri kamal traders (BID ID -3340699)