ADDN/ALTERNATION TO CERTAIN OTM ACCN AND SPECIAL REPAIR TO OTM BUILDING NO T-96, T-57, T-70 AND T-79 OF 157 INF BN TA AT MIL STN BD BARI UNDER GE KALUCHAK

Amount

Dismantling of AC corrugated sheets of any thickness as in roofs including ridge complete all as specified and as directed.

Dismantling timber scantlings 40 sq cm and over in section, in any position complete all as specified and as directed.

Demolition of brick /stone masonry built in cement nortar of any description complete all as specified and as directed.

Taking down cement plaster on bricks or stone wall/ decayed surfaces of concrete from roof projectiokn or RCC Chajjas etc. including racking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

Dismantling floor,hearth or wall tilling,cement mortar bedding(but including backing) , terrazzo toping complete all as specified and as directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/slabs/blankets any thickness complete all as specified and as directed.

Dismantling framed trusses including purlin not exceeding 10 m span complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exceeding 1.5 Sqm & not exceeding 4 Sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 1 sqm and not exceeding 2 sqm each and refixing in same opening after repair complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) not exceeding 1.50 Sqm each complete all as specified and as directed.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness complete all as specified and as directed.

Demolition of reinforced cement concrete, shelves, chajjas, slabs and similar work carefully and matching to adjoining disturbed surfaces complete all as specified and as directed.

Demolition of cement concrete in and paving (un reinforced) exc. 15 cm. thickness, below or above ground level, including removal of waste from defence land and dumping at a place as specified by civil authorities complete all as specified and as directed.

Dismantling wrought iron or mild steel as chanel work of any description not otherwise complete all as specified and as directed.

Dismantling cast iron or reinforced concrete drain pipes of 75/100mm bore, fixed with walls and taking out of trenches, if required complete all as specified and as directed.

Taking up or down 15 mm steel tubing and connections including clearing for refixing or removal to store complete all as specified and as directed.

Taking up or down 20 mm steel tubing and connections including clearing for refixing or removal to store complete all as specified and as directed.

Cement concrete (1:2:4) type B1using 20 mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and as directed.

PCC 1:3:6 type C - 1 (using 20 mm graded crushed stone aggregate) as in back filling of chowkats and bed blocks for hold fasts etc complete all as specified and as directed.

Providing cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate ) in roof padding, roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

RCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and colums, in floors, roofs, landing balconies, canopies, deck slabs, chajja and in shelves and the like, complete all as specified and as directed.

Cement concrete type D-2 1:4:8 (40mm graded crushed stone aggregate) in foundations, filling and mass concrete in sub base complete all as specified and as directed.

Hard core, of broken bricks broken to gauge n exc 63mm for laying sub base of thickness 150mm complete all as specified and as directed.

Brickwork with sub class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed.

Brick work with sub class ‘B’ bricks ,straight or curved on plan exc 6 m mean radius and built in cement mortar 1:6 complete , but except bricks , i.e using serviceable bricks obtained from demolition complete all as specified and directed

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup ports, overhangs, etc also splays between floors and beams etc complete all as specified and as directed.

2nd class hard wood 35mm thick factory made Plain framed panelled shutters(any number of panels) with lock rail and panel of 9mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces the size of rail and stile as per IS; 1003 (Part-I) Kiln seasoned and chemically pressure treated supply and fitted to chowkats complete all as specified and as directed.

2nd Class hard wood 35mm thick factory made glazed and skelton shutters open rebated and prepared to receive glass , gauze,etc (without sash bars) edges of framing plain , chamfered or rounded. Fitted with cut and mitred beads for securing wiremesh supplied and fitted to chowkats complete all as specified and directed.

Factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed.

Factory made solid panel PVC door/cup board shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, suippling and fixing in the frame at site as per specification in SSR Part-I. complete all as specified and as directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (both type) 300mm longh, and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Aluminium anodised 150mm long barrel tower bolt of extruded section and fixing complete all as specified and as directed.

Aluminium handles cast type anodised 150mm complete all as specified and as directed.

Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel springs, fixed in floor with over all length of cover plate 150mm complete all as specified and as directed.

Helical door spring complete all as specified and as directed.

150mm floor door stopper of aluminium alloy body tongue anodized with hard drawn steel spring fixed in repairs complete all as specified and as directed.

Butt hinges, medium weight, cold rolled mild steel, welded to steel frame work of 100mm size complete all as specified and as directed.

125mm size aluminium handle fabricated type anodized all as specified and as directed.

Mild steel 300 mm, ordinary rat tail rod pattern door springs including roller and roller plate and fixed to steel door frame complete all as specified and as directed.

Steel locking bolts wuth mild steel electo galvanised plate and bright bolt not less than 10 mm dia, 100 mm size complete all as specified and as directed.

40 mm wide flaps Continuous (piano) hinges , mild steel bright finish or electrogalvanised as in cup boards, kitchen cabinat , etc complete all as specified and as directed.

Ball catches with 8mm dia steel ball, and brass body and stricking plate inccluding letting complete all as specified and as directed.

Fancy type drapery rod powder coated 20 mm dia fixed to bracket and dom type corner ends fixed in repairs complete all as specified and as directed.

MS Brackets powder coated for holding curtain rods fixed with screws to walls as approved by complete all as specified and as directed.

Fibre fancy dome type corner ends fixed to curtain rods 20mm dia complete all as specified and as directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with 2nd class soft wooden beadings complete all as specified and as directed.

Refixing Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) complete all as specified and as directed.

Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410 W (gde E-250) complete all as specified and as directed.

Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe 410 W (gde E-250) complete all as specified and as directed.

Plates (plain or chequered) chennels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachement conforming to Fe 410 W (gde E-250) complete all as specified and as directed.

Mild steel purpose made bolts of diameter of neck exceeding 12 mm but not exceeding 20 mm with hexagonal or square head on one end and screwed the other or screwed both ends, each screwed ends to be fitted with washers and one hexagonal or square nut not exceeding 30 cm long complete all as specified and as directed.

Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, keys , hinges lock, lock strike plate etc.made out of 1.25mm thick MS sheet including one shop coat of red oxide zinc chrome primer etc complete all as specified and directed .

TMT bars 10mm dia and over cut to length, bent to shape required including cranking and bending spirally or hopping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.90mm dia) or securing with clips complete all as specified and as directed.

All as per decription Srl item No 53 here-in-before but 5 to 10 mm dia as in stirrups, spacer etc complete all as specified and as directed.

Box type steel windows comprising of tubular frame and shutters made out of 1.25mm thick MS steel tube, factory made, with double side shutters wire gauged shutter and glass glazed shutter (wire and glass panes shall be measured and paid separately) with side hung shutters with steel handle and steel peg stay dovetailed or welded including 2 Nos tower bolts 150 mm long for each leaf and 8mm square bar grills at spacing as shown on drg welded to F1 frame work, including other fittings, hinges, handles tarred hold fasts PCC blocks etc all as shown on Drawing No CEPZ/TD-354/09 sheet 1/3 to 3/3 including taking down old steel window of any size complete all as specified and directed.

Steel ventilator with top hung shutter including hinges , steel peg stay including taking down old steel ventilator of any size complete all as specified and as directed.

Aluminium anodized powder coated frame of size 124.60mm x 44.45mm made out of 1.60mm thick aluminium section, powder coated, fixed to floor wall with plugs and screws complete all as specified and as directed.

Aluminium anodised powder coated window/ventilator shutter, section of size 44.45 x 44.45mm made out of 1.6mm thick aluminium sheet/section including necessary jointing cleats, glazing clips, rubber packing, suitable handle 1 No's in each shutter, tower bolt, hinges 110mm long, anodised aluminium snap beading screws, complete all as specified and as directed. Note : Sheet glass to be fitted will be measured and paid separately.

Aluminum anodized powder coated grill fixed in windows complete all as specified and as directed. Note : Thickness and type of grill shall be approved by GE.

0.80 mm thick plain , galvanised , mild steel sheeting , in ridges, hips, valley gutters, drip and straight flashing ( length and girth as fixed ) of class -3, complete all as specified and as directed.

Prepainted galvalume aluminium zinc coating G.I based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPa as in roof covering /cladding to wall, fixed with self taping screws complete all as specified and as directed.

Prepainted galvalume aluminium zinc coating G.I based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPa as in roof covering /cladding to wall, fixed with self taping screws as in ridge covering complete all as specified and as directed.

Suspended false ceiling system using 4mm thick high pressure steam cured fibre cement pre-primed textured varient E-board (classic), ISI marked, conforming to IS:14982-2000 over and including GI snap grid frame work for false ceiling, grid size 605 x 605 mm with GI angle of size 24x24mm, main runner ‘T’ of size 24x38mm, secondary runner ‘T’ of size 24x28mm with 6mm GI wire with butterfly clips for leveling, fastners, supports, plugs to walls/joists etc all as per manufacturer’s Instructions, including making holes, cutting chasis and making good existing walls in cement mortar 1:3 or PCC 1:2:4 type B1, complete all as specified and as directed. Note : All steel members shall be hot dipped galvanised with zinc coating not less than 120 gm/sqm.

Suspended false ceiling system using E grid suspended ceiling grid system Grid size 600mm x 600mm with and including G.I frame work of main runners 38mm x 24 mm , cross tee 28mm x 24mm and wall angle 24mm x 24mm hot diped galvanised steel with zinc coating not less than 120 gm/ sqm using 4mm thick high pressure steam cured fibre cement pre primed textured variant E board classic ISI marked IS-14862-2000 to be placed in grid of E grid suspended ceiling grid system duly suspended by 6 mm dia gi bar hangers from existing purlins to roof with butterfly clips complete all as specified and as directed.

Glass fibre reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent). Base coat: Berger HS Latex plus (or equivalent) Consumption base coat: 0.3 kg/m2 Reinforcement: Glass fiber Second and Third coat: Latex sheild 2K (or equivalent) Consumption top coat: 3 kg/m2 System requirements: density: 2.00 kg/ltr; compressive strength: 0.5 N/mm2. • Wall penetration through the RCC slab must be sealed using Berger HS RepirO(or equivalent). • Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus(or equivalent) modified mortar with a bonding coat of Berger HS Latexplus(or equivalent) modified cement slurry upto 5ft. • All depressions, unevenness, surface honeycombing shall be repaired using Berger HS Latex plus(or equivalent) modified polymer mortar with a bonding coat of Berger HS latex plus(or equivalent)modified cement slurry. Including cleaning of RCC surface to remove dust, loose particles, etc with compressed air or any other suitable technique depending on site conditions, grinding any sharp edges, etc

Complete removal of the existing roof treatment, any type viz. tarfelt or membrane surface or roof tiles etc. including grubbing up of tree roots and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water all loose dirt/dust and applying the following Roof Treatment complete all as directed :- component liquid ,solvent free ,cold applied , water-proofing membrane that is highly elastic and UV resistant with 10 years Warranty .ASTM D 6083-97a Waterproofing and heat reflecting system having following key performance properties: 1.UV resistant ,prevent yellowing and weathering 2.Highly elastic upto 350% and crack bridging 3.Excellent adhesion on porous and non-porous substrates 4. Tensile Strength >10 N/mm2 with GeoTextile fleece 5. Soler Reflective Index (SRI) more then 109-111 ASTM E1980-11 System: First coat:Providing and applying primer over the prepared surface with HS PU roofkoat Primer(or equivalent) Coverage: 0.2kg/m2(with 50% dilution of water) Reinforcement: Geotextile 40 gsm Second coat:Home sheildroofkoat(or equivalent) Consumption: 0.5 kg/m2. Third coat: HS PU roofkoat(or equivalent) Consumption : 0.8 kg/m2. System buildup-1.5kg/sqm with geotextile of 40gsm For accessible roof, tiles with screed/ adhesive may be fixed thereafter.

75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection etc, finishing surface even and fair without using extra cement including making joints with bitumastic filling in proportion of bitumen and sand 1:3 by weight complete all as specified and as directed. (Note : The concrete shall be laid at a stretch not exceeding 3.0 m in length and every turning/ corners.

Glazed ceramic coloured tiles of size300x450x7 mm thick as in vertical surfaces such as skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed.

Non Skid joint free ceramic tiles 300 x 300 x 7 to 8 mm thick in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 complete all as specified and as directed.

Non - skid ceramic coloured jointless tile 400mm x 400mm x 7mm thick as in floors laid over and including 15 mm thick screed bed or bedding layer of cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles complete, complete all as specified and as directed.

Non - skid ceramic coloured jointless tiles 400mm x 400mm x 7 mm thick on vertical surfaces such as skirting /dado etc bedded & jointed in neat cement slurry over and including 10 mm thick backing coat of cement mortar 1:4 and pointed in white or coloured cement to match the colour of tiles complete, all as specified and directed.

Glazed/anti-skid vitrified dark shade tiles 10mm thick (square/rectangular polished area of each tiles n.exc 0.36 sqm regular use as in floor set and jointed in neat cement slurry and pointed in coloured cement to match the shade over and including 15 mm thick screed bed in cement mortar 1 :4 complete all as specified and as directed.

Glazed/anti-skid vitrified dark shade tiles 10mm thick (square/rectangular polished area of each tiles not exceeding 0.36 sqm regular use as in vertical surface set and jointed in neat cement slurry and pointed in coloured cement to match the shade fixed over 10 mm thick screed in cement mortar 1:4 as per manufacturer instructions complete all as specified and as directed.

Black granite of 18 to 20mm thick (Table rubbed and polished) as in cooking platforms and the like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shed of makrana doogri stone complete all as specified and as directed.

Machine cut kota stone slab in steps 18-22 mm thick over cement screed bed laid and jointed cement screed bed laidand jointed with grey cemant slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for floor/ tread of staircase over and including15mm thick screed bed in cement mortar 1:6 after roughening surface of old concrete floor by picking sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg og cement per sqm complete all as specified and as directed.

All as per decription Srl item No 75 but on vertical faces of walls as in skirting and dados including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and as directed.

25 mm thick PCC 1:3:6 type C-1, (using 20mm graded crushed stone aggregate) as in sub-base finished even and fair complete all as specified and as directed.

25mm thick PCC (1:2:4) type B1 with 20mm graded aggregate for laying floor tiles complete all as specified and as directed.

Rendering 15 mm thick on fair faces as per manufacture instruction of brick/concrete surfaces in cement plaster 1:4, by using liquid water proofing compound , finished even and smooth without using extra cement, complete all as specified and as directed.

Rendering 10mm thick in cement plaster 1:6 on fair faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 5 mm thick on concrete surfaces of ceilings in cm 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound, complete all as specified and as directed.

Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 with water proofing compound tobe finished even and smooth without using extra cement complete all as specified and as directed.

Taking down cement plaster and decayed concrete of any description, upto triple storey of building, from roof projection, chajjas etc and making good the decayed portion with cement mortar 1:3 mixed with water proofing compound or mixed with WPC or PCC 1:2:4 type B-0 (using 12.5mm graded aggregate) including necessary form work where ever required and finally finishing the surface with 15 mm thick cement plaster in CM 1:3 and applying two coats of white wash/colour wash/cement base paint/exterior emulsion paint to match the existing surface /finish, complete all as specified and as directed.

Preparation of newly plastered surface by finishing the undulated surface with cement putty and applying two coat of weather proof paint (Apex) after application of one coat of primer complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil emulsion distemper over a coat of chalk whiting with 1 to 2 mm thick wall care putty complete all as specified and as directed.

Two coats synthetic enamel paint over a coat of red oxide primer on new steel surfaces over 10 cm width or girth complete all as specified and as directed.

Preparation of old painted steel surface of any description, over 10 cm in width or girth not other wise described, and applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of old distempered surfaces and applying one coat of oil emulsion distemper on walls complete all as specified and as directed.

Preparation of old treated surfaces and applying two coat of weather coat on walls over one coat of primer complete all as specified and as directed.

Preparation of new plaster surfaces of ceiling and applying three coats of white wash on ceiling, complete all as specified and as directed.

Preparation of old ,plastered or unplastered surfaces including brooming down or steel wire brushing,scrapping down smokesoot,moulds,moss and efflorescent salts and trading oil greasy spots, and applying one coats of cement base paint on walls complete all as specified and as directed.

Preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and as directed.

Sheet glass 3mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm each pane complete all as specified and as directed.

5mm thick tinted glass as in aluminium door and window with aluminium hollow beading/glazing clip size 19mm x 17mm made out of 0.70mm thick hollow section weighing not less than 0.97 Kgs/RM including rubber gasket, complete all as specified and directed.

3mm thick figured glass, pin head and glazing with oil putty in square not exc 0.5 Sqm in each pane complete all as specified and as directed.

Steel tubing medium grade galvanised of 20mm bore with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

Steel tubing medium grade galvanised of 15 mm bore with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

Bib taps 15mm dia cast copper alloy fancy type chromium plated, screwed down for iron pipe or for brass ferrule fixed in repair complete all as specified and as directed.

Angle valve 15 mm fancy type, chromium plated cast copper alloy, screwed down for iron pipe ,fixed in repairs complete complete all as specified and as directed.

Fancy type Brass CP wash hand basin mixer for mixing hot & cold water, screwed down, high pressure screwed both ends for 15 mm bore iron pipe or for unions fixed in repairs complete all as specified and as directed.

Shower rose of C.P. with swival joint of size 125mm for fixing 15mm pipe including fixing to steel pipe or union fixed in repairs complete all as specified and as directed.

PVC connections 15mm dia & 600mm long with PTMT nuts fixed in repairs complete all as specified and as directed.

PVC connections 15mm dia & 450 mm long with PTMT nuts fixed in repairs complete all as specified and as directed.

Sheet glass shelf assembly consisting of 5,5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed in repairs complete all as specified and as directed.

PTMT grating doom 100mm dia with hole for waste pipe fixed in repairs complete all as specified and as directed.

CP brass hot & cold 15mm dia wall mixture with provision for overhead shower with 115 mm long bend pipe on upper sie connecting legs & wall flanges for mixing hot & cold water fixed in repairs complete all as specified and as directed.

CP Health faucet 8 mm dia for EWC 1.20 mtr long flexible pipe with two steel check nuts Cat part No ALD-573 Make Jaguar, fixed in repair complete all as specified and as directed.

Vitreous china wash down water closet (pedestal pattern) coloured complete, including connection to drain pipe and to flushing pipe antisyphonage pipe etc, including seat cover fixed in repair, complete all as specified and as directed.

Low level flushing cidtern PVC valveles ,syphonic action type flushing cistern white with inlet valve,float and handle including bracket etc fixed in repairs complete all as specified and as directed.

600x450mm PVC cabinet mirror of superior quality fixed in repairs complete all as specified and as directed.

Vitreous china wash basin with full pedestal white flat back size 560x430x195 mm including complete fixing accessores Cat Part No CNS-WHT-811, CNS-WHT-811 fixed in repairs complete all as specified and as directed.

Vitreous china wash hand basin table top type fixed on counter including CP waste coupling & waste pipe complete all as specified and as directed.

Gun metal gate valve iron wheel head screwed both ends for iron pipe of 20 mm bore complete all as specified and as directed.

CP Single Towel Rail 600 mm long complete all as specified and as directed.

Soap dish complete all as specified and as directed.

Fancy type chromium plated shower rose with swivel joints, 50 mm dia including fixing to steel pipe or union fixed in repairs complete all as specified and as directed.

Vitrous china urinal bowl type (flat black or corner wall type ) complete including providing and fixing plugs bedding urinal against wall in cement mortar 1.2 securing urinals to plugs with and incl 60 mm long brass screw pointing around urinal back in cement complete all as specified and as directed.

PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall including fixing clamps complete all as specified and as directed.

PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints fixed to wall including fixing clamps complete all as specified and as directed.

PVC (SWR) bends any radius 75mm bore complete all as specified and as directed.

PVC (SWR) junction single (single T) equal or unequal 75mm bore complete all as specified and as directed.

PVC (SWR) bends any radius 110mm bore complete all as specified and as directed.

PVC (SWR) junction single (single T) equal or unequal 110mm bore complete all as specified and as directed.

Vitreous china water closet Orissa pattern long pan size 580x440mm with trap front or back inlet and integral foot rest complete fixed in repair including lime concrete bedding and connection to drain or outgoing pipe and to flushing pipe and anti siphon pipe complete all as specified and as directed.

Pillar taps 15mm bors cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed to iron pipe & fixedcomplete all as specified and as directed.

20mm dia High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in as spout pipes to pour out rsidual water out from the treated area complete all as specified and as directed.

Taking down old unsv copper/aluminium point wiring concealed / batten (light, fan, socket or power) complete, including fixture and fittings such as switches,sockets, ceiling roses,bell push,bell electric,lamp holder,bulk head fitting, pendants, regulators, sockets, light fitting and any type switch board wooden/iron,round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

Taking down distribution boards/wooden board ,switch fuse units,steel enclosures for MCB of any type and removing from site complete all as specified and as directed.

Taking down existing unserviceable submain wiring any size and making good the disturbed surface complete all as specified and as directed.

Taking down existing Ceiling fan and deposited in MES store yard complete all as specified and directed.unserviceable submain wiring any size and making good the disturbed surface complete all as specified and as directed.

Point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 Sqmm copper conductor flexible FRLSH insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall , plastering after concealing conduit , including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc and including making good the disturbed surface as per existing complete all as specified and as directed.

All as per description Srl item No 133 above but for 5 Amp socket outlet on same board complete all as specified and as directed.

All as per description Srl item No 133 above but for socket outlet on independent board complete all as specified and as directed.

All as per description Srl item No 133 above but for One light point controlled by two 2 way switches, with cable 1.5 Sqmm complete all as specified and as directed.

All as per description Srl item No 133 above but for 15 Amp socket outlet independent controlled by 15 Amp switch with 2.5 Sqmm copper conductor multistrand cable pvc insulated FRLS and unsheathed cable in and including PVC rigid concealed conduit 20/25 mm dia and unsteathed copper conductor multistrand cable 2.5 Sqmm as earth wire FRLS pvc insulated in green color complete all as specified and as directed.

Modular switch 1 way 6A,1 module , 240 volts ISI marked complete all as specified and as directed.

Modular Socket, 6A - 5 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

Modular switch 2 way 6A,1 module , 240 volts ISI marked complete all as specified and as directed.

Modular switch 1 way 16A, 1 module , 240 volts ISI marked complete all as specified and as directed.

Modular Socket 6A/16A - 6 pin combined 2 module, , 240 volts ISI marked complete all as specified and as directed.

Replacement of Switch piano flush type single pole, one way 5 Amp , complete all as specified and as directed.

Replacement of Switch socket out let combination universal type, 2 in 1, 2 and 3 pin 5 Amp, piano flush type, 240 volts, complete all as specified and as directed.

Replacement of Switch socket outlet combination universal type, 2 in 1, 3 pin 5 and 15 Amp, piano flush type, 240 volts, complete all as specified and as directed.

Bell push flush type piano 5 Amp complete all as specified and as directed.

Bell multi music ,230volts AC single pole complete all as specified and as directed.

Ceiling rose, 3 Phase/PVC/polycarbonate isolated body complete all as specified and as directed.

Fan regulator stepped electronic type suitable for AC, 240 Volts complete all as specified and as directed.

Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Self ballast LED retrofit Lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and as directed.

LED lights fitting 1x 20W, 220V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.95 , 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. (4' ft long ) with LED rod 20 watt, 230 Volts 50 Hz. complete all as specified and as directed.

LED light fitting 1x9W/1X10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Inverter LED lamp,6500K,900lm in white colour of 9 Wattbase cap B-22 with poly carbonate difusser and aluminium heat sink , complete all as specified and as directed.

Integral LED street light luminaire 60W LED 230 volts made of pressure die cast aluminium housing with high power LED’s lens & toughned glass IP-66 including GI 40mm mounting bracket fixed on wall with necessary clamps,nuts and bolts and making connection with PVC copper flexible cable 1.5sqmm complete all as specified and as directed.

LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistantcomplete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete withIP 65/66 protection complete all as specified and as directed.

Factory made epoxy powder coated Distribution board vertical TPN 6 ways (TPN MCB DB) with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cale management, top and bottom removable gland plates with Knockouts and suitable for one FP-MCCB 160/250 Amp as incomer and SP/TP MCBs outgoing fixed in repair complete all as specified and as directed.

Factory made epoxy powder coated Distribution board vertical TPN 4 ways (TPN MCB DB) with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cale management, top and bottom removable gland plates with Knockouts and suitable for one FP-MCCB 160/250 Amp as incomer and SP/TP MCBs outgoing fixed in repairs complete all as specified and as directed.

Replacement of distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and as directed. Note:- Distribution board and MCBs should be same make.

Replacement of distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 12 way 240 volts double door complete all as specified and as directed. Note:- Distribution board and MCBs should be same make.

Isolator 4 Pole, TPN 415 volts, 100 Amps rating with rupturring cap 16 KA, complete all as specified and as directed.

Replacement of Thermal magnetic release MCCB 4 pole 415 volt rapturing capacity 25 KA 0f size 63 amp complete all as specified and as directed.

Replacement of Thermal magnetic release MCCB 4 pole 415 volt rapturing capacity 16 KA 0f size 63 amp complete all as specified and as directed.

Supply and fix in replacement of MCB SPN-6-32 Amp, 240 volts 50Hz AC supply, complete all specified.

MCB single pole neutral 240 volts, 40 Amps, ,"B" series 10 KA complete all as specified and as directed.

MCB single pole neutral 240 volts, 63 Amps, ,"B" series 10 KA complete all as specified and as directed.

Replacement of 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB complete all as specified and as directed.

Sub main wiring with proper colour coding , insulated , unsheathed , multistranded ,copper conductor FRLS, cable of 4 run 10 Sqrmm for phase and neutral and one run of 6.0 Sqrmm for earth wire unsheathed , miltistranded , copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length incl taking down old wiring. complete all as specified and as directed. Note : Wiring shall be done in proper colour coding.

Sub main wiring with proper colour coding , insulated , unsheathed , multistranded ,copper conductor FRLS, cable of 2 run 6 Sqrmm for phase and neutral and one run of 6.0 Sqrmm for earth wire unsheathed , miltistranded , copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length incl taking down old wiring complete all as specified and as directed. Note : Wiring shall be done in proper colour coding.

Sub main wiring with two single core PVC insulated (unsheathed) multi strand copper conductor FRLS cable of size 6 Sqmm and one single core PVC insulated (unsheathed) solid copper conductor FRLS cable of size 4 Sqmm as in continuous earth wire drawn into and including concealed PVC conduit medium grade 25mm dia ISI marked complete with fittings and fixings accessories complete and including cutting chases pinning in making good to facing and pointing in using cement moter 1:3 and making good disturbed surface complete all as specified and as directed.

Testing water heater storage type(Geyser)single phase 230V,50Hz ,5 star energy saving high density PUF insulation tank made of heavy duty magnesium anode rod with steel core to protect enamelled tank from rust & corrosion ,vertical installation type, 25 Litre capacity,2000Watt rated power,incoloy 800 glass coated heating element,tank coating of feroglas powder,tank made of ultra thick super cold rolled steel plates,rated pressure 0.8MPa,IPX4 protection consist of safety valves,thermal cut off, thermostat including connecting up fixed to walls by drilling of holes ,grouting of bolts of suitable size with nuts etc and making good disturbed surface complete all as specified and as directed.

Exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers including taking down old one and deposited to MES Store.Making holes for 300 mm exhaust fan of suitable shape & size into or through brick walls including plastering for making good to the original surfaces of any description disturbed including painting /distemper matching with the existing colour including taking down old one and deposited to MES Store complete all as specified and as directed. Note : The rates includes for making good to the original surfaces of any description disturbed including painting /distemper matching with the existing colour

Ceiling fans complete with blades, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Excavation in trenches n exc 1.5m wide and n exc 1.5m deep and making good Bottom surface for laying / removing of cable all as specified and directe in hard dense soil complete all as specified and as directed.

Returning filling in excavated soil in trenches, watering and well ramming in layers not exceeding 25cm complete all as specified and as directed.

Remove of excavated surplus soil to distance not exc 50m and depositing where directed at a level not exceeding 1.5m beyond starting point, complete all as specified and as directed.

Sand filling in cushioning bed of cable and consolidation complete all as specified and as directed.

Common burnt clay building sub class `B' bricks, laid over sand Cushioning laid at right angle along with cable, complete all as specified and as directed.

Supplying, laying and testing cable XLPE Insulated screened PVC bedded galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor 1100 V grade cross sectional area 50 Sqmm,3.5 core in and incl taking out old one complete all as specified and as directed.

Cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 3.5 Core, including glands, lugs, nut, bolts, washers as required at site, testing complete all as specified and as directed.

Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing complete all as specified and as directed.

Cutting existing steel tubing 15 mm bore for alterations or additions (Each cut measured) complete all as specified and as directed.

Screwing existing steel tubing 15mm for alterations or additions complete all as specified and as directed..

Dismentaling and taking out rusted/corroded pipe line off sizes 20/25/50mm bore from trenches/PCC. Note Exc and earth work will be measured and paid seperately under respective items complete all as specified and as directed.

Cutting existing 80/100/150 mm GI pipe and inserting GI Tee of size 100x100x50 mm for tapping including necessary earth work and making flange for connection of new 50 mm of GI pipe including complete all as specified and as directed.

GI tubing tight graded including all accessories for encasing cables for mechanical protection, laid under plinth/floors/path culverts with complete accessories such as bends/sockets/reducers/saddles incl necessary threading/drilling works all as specified and directed of sizes (MS work will be measured under separate item in schedule) 40 mm complete all as specified and as directed.

Replacement of tubing GI "medium grade" with all fittings laid in floor or trenches including taking out old UNSV pipe of size 50 mm dia complete all as specified and as directed.

Replacement of tubing GI "medium grade" with all fittings laid in floor or trenches including taking out old UNSV pipe of size 25 mm dia complete all as specified and as directed.

Replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 50 mm bore complete all as specified and as directed.

Replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 25 mm bore complete all as specified and as directed.

M/S Vishwakarma Builders (BID ID -3307701)

GENESIS INDIA (BID ID -3308558)

M/s Anand Prakash (BID ID -3308254)