PROVN OF ONE COVERED SHED OF SIZE 15 X 15 WITH GALVANIZED SHEET AND SIDE BRICK WALL WITH 03 X WINDOW FOR OBSERVATION AT LPR KHAMARIA UNDER GE (P) NO 1 JABALPUR

Amount

Surface excavation in hard/ dense soil n.exe 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil

Excavation in trenches n exc 1.50 mtr wide and n exc 1.50 mtr depth for foundation etc and getting out in hard/dense soil complete all as specified & directed.

M & L PCC 1:4:8 type D2 using 40 mm graded stone aggregate foundation filling mass concrete.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering

M&L for hard core of gauge n exc 63mm deposited spread and leveled in layers n exc 15cm thick watered and rammed to a true surfaces of broken stone or boulder complete all as specified and directed.

S & F tor steel or TMT bar 10 mm dia and over cut to length bend to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including M.S wire ( annealed) not less than 0.9 mm dia

S & F TMT bars 5mm dia and over upto and incl 10mm dia , cut to length , bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including M.S wire ( annealed) not less than 0.9 mm dia as in stirrups, spacer and binders

M&L RCC M- 20 Nominal mix (1: 1 1/2:3) Type A2 (20mm graded aggregates) as in foundation, footing, foundation beam, plinth beam and base for column all as specified and directed.

M&L RCC M- 20 Nominal mix (1: 1 1/2:3) Type A2 (20mm graded aggregates) as in columns all as specified and directed.

M&L RCC M- 20 Nominal mix (1: 1 1/2:3) Type A2 (20mm graded aggregates) as in beams all as specified and directed.

Use & waste for flat formwork to sides of concrete foundations, footings, bases of columns raft and raft beams, sides and soffits if any of foundations and plinth beams and similar work, etc, rough finished surfaces of concrete etc all as specified and directed

M&L for form work to sides of pillars , posts struts, piers columns and stanchions, square, rectangular or polygonal rough finished surfaces of concrete etc all as specified and directed

M&L for flat formwork to sides and soffits of floor or roof beam hunchings, girders bresummers, lintels, cantilevers, shelves, including supports overhangs etc also splays between floors and beams etc, rough finished surfaces of concrete etc all as specified and directed

Returning, filling in incl spreading, leveling, watering and well ramming in layers n exc 25 cm complete all as specified & directed.

Removing excavated material to a distance n exc 50 mtr and depositing where directed at a level n exc 1.50 mtr above the starting point complete all as specified & directed.

M&L flyash modular Birck curved on plan exc 6 metre mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L plastering in CM (1:6) 10mm thick on brick masonry walls and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on brick/concrete surfaces fished even and smooth w/o using extra cement.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in path/plinth protection finished even and fair incl expansion joint at every 3.0m interval and every corner complete all as specified and directed.

M & L non skid ceramic coloured/designer tiles 7 to 8 mm thick (square rectangular ) area of each tile exc 0.11 sqm but nexc 0.18 sqm, in floors and 25 mm thick PCC type B-1 1:2:4 (20 mm graded aggregate) laid over & including 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white cement to match

S & F Solid WPC Single door frame of size 65mm x 100mm made out of 5mm Plain colour PVC sheet reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing

S&F Factory Made Solid WPC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board core supplying & fixing in frame at site as per specification & drawing

S&F precoated steel window Rolled formed GI Section ECO 4000 (Openable double rebate window) Providing and fixing of single rebate openable/fixed windows made of galvanized steel colour coated/powder coated (base steel as per IS 513 of “D" quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 microns, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 48 x 50 mm, centre mullion section 48 x 50 mm, shutter section 47 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consists rebate for glazed shutter with a 20 mm provision for guard bars/grills and the sections cut to length mitre joined with corner bracket, centre mullion fixed with mullion cap, handle, stay, 2 nos. SS( stainless steel) heavy duty pivot hinges per shutter and window fitted with 5mm thick plain float glass with EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing frames in concrete/masonry wall by means of self expanding screws, Including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. complete as per the direction of Engineer in Charge.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm with stainless steel wire staples

S&F in repair Curtain dropary 25 mm dia PVC Coating mild steel fancy type rod of fancy type including brass and brackets with curtain rings of approved quality etc complete.

S & F mild steel frame work such as grills, grating framed guard bar with ends of bars shouldered and / or riveted and similar work confirming to Fe-410-0 or Fe-310-0 complete all as specified and directed.

S & F figered glass, pin headed type in squares 3 mm thick not exc 0.50 Sqm in each panes and glazing with oil putty etc complete all as specified and directed.

S & F aluminum alloy anodised, sliding door bolts with hasp and staple, (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed 300mm long.

S & F aluminum anodised, barrel tower bolts of extruded section and fixed 150 mm long.

S & F extruded aluminum alloy handles, fabricated type, anodized 150 mm long.

S & F Butt hinges, medium weight, cold rolled mild steel and fixed 100 mm long.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm (Profiled) thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall of mangalore pattern design, fixed with self tapping screws as specified & directed

S&F Rolled mild steel sections as in main & cross beams, hip & jack rafters; purlins where connected to common rafters & running rails & guides for sliding doors; fixed with angle cleats or other connecting plates GDE Fe410-W (Gde-E-250)quality -A

S & F mild steel flat iron as in wind tie for roof including securing bolts.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrom primer, complete all as specified and directed.

M & L preparing plastered / unplastered new surfaces of walls and applying two coats of distemer over a 3mm thick putty specified and directed by Engr-in-Charge

M & L preparing plastered/ unplastered new surfaces of walls and applying two coats of cement base paint over alkali resistant primer complete all as specified and directed.

M&L for point wiring with 1.5 Sq mm, FRLSH, PVC insulated, single core, unsheathed, multi stranded 1100 volts grade, copper conductor cable drawn through concealed conduit and including concealed PVC rigid non metalic conduit of size 19 mm, on ceiling/wall, with and including continuous 1.5 Sqmm, FRLSH, PVC insulated single core multi stranded copper conductor cable earth continuity conductor connected to common earth and earth dolly and including sunk metal sheet enclosure rectangular terminal boxes of suitable size and white cover plates suitable for mounting modular switches, sockets etc and making good the disturbed surfaces with cement sand mortar 1:3 to match with the existing surfaces all as specified and directed for one light Point/fan point controlled by one switch.

All as per item 39 above in before but with one 3 pin, 5 amps, socket outlet on the same board.

All as per item No. 40 here in before but with one 3 pin, 5 amps socket outlet on independent board.

Description same all as per item No 39 here in above but with 1100 Volts grade copper stranded conductor FRLSH cable of size 2.5 Sqmm main & with 2.5 Sqmm earth multi-strand copper conductor cable as earth wire for 3 pin switch socket outlet 15 Amp on Independent board complete all as specified & directed by Engineer-in-Charge.

S&F in replacement of modular switch 6-10 Amps one module 230 volts AC as per existing model/make complete all as specified and as directed

S&F in replacement of modular socket, 6A -2/3 pin combined 2 module, 230 volts AC as per existing model/make complete all as specified and as directed.

S&F in replacement of modular switch 16 Amps one module 230 volts AC as per existing model/make complete all as specified and as directed

S&F in replacement of modular socket, 6/16A -2/3 pin combined 2 module, 230 volts AC as per existing model/make complete all as specified and as directed .

S&F Ceiling rose surface type 65x50 mm three terminals of polycarbonate body complete all as specified & directed.

Supply and fixing Single phase ceiling fan 1200 mm permanent magnet brushless DC Motor 230 v 50 Hz single phase 26-30watt rated current 0.16 amp,pf 0.98 370/360 rpm air delivery 220m3 rated service value 629m3/min/watt no of blades three type of blade leaf 1.05 mm thick aluminium sheet remote control radio frequency 5 speed +off timer option speed regulation class of insulation two nos bearings including connecting wire,electronic regulator complete with all as required and directed at site by eng in charge Make : Bajaj/havells.

Supply & Fixing Smart bright Batten Series, LED luminaire using LEDs 22 watt, natural white, 2200 Lumen, THD max 10 % ,CRI min 80 % with diffuser which ensures uniform distribution and comfort batten series features latest LEDs and delivers consistent light output with wide voltage protection range, stable color start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall and ceiling mounting using brackets (supplied along with The Luminaire has been tested as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl), report has established conformity of the product(s) to the requirements of the Standard/Specification Make : Philips Cat part BN 021 LED 22S4000 PSU GR SI or equivalent.

Supply and Fixing Sheet metal enclosure for DBs when MCBs to be Used, 4 way, SPN, double door type, 240 Volt with 200 amps rated busbar complete all as directed.(Note : MCBs will be Measured separately)Make:Legrand or equivalent

S&F in replacement MCB Single Pole and Neutral 240Volt, upto 40 Amps,10KA breaking capacity complete all as specified & directed.Make: Legrand cat no :4086 18 or eq in SEIMENS /General Electrical

S&F in replacement MCB Single Pole 240Volt, upto 40Amps,10KA breaking capacity complete all as specified & directed..Make: Legrand cat no :4086 90/92/93/94/95/96 or eq in SEIMENS /General Electrical

Supply , laying and testing cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 2 core 10 Sqmm complete all as specified and directed by Engineer in charge

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth , for foundation, etc or for shafts, wells, cesspits, manholes, pier holes,etc. n exc 10sqm on plan and n exc 1.5m in depth and getting out in any type of soil

M/L for Returning , filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

M/L for Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed.

Supply,laying & fixing double wall corrugated (DWC) pipes made of high density polythyline (HDPE) with all accessories i.e. all type of joints,Sockets,Elbows,bends and End caps etc.. all as specified and directed by Engr in Charge.of size 50 mm outer dia and 38 mm inner dia of Make : -Telerex/Tirupati or E-in-C approved Make

M/L for GI Tubes,of size 40 mm dia light grade, galvanised, with all fitting , laid in trenches for protection of cable in road /drain crossing complete all as specified and as directed.

.Earthing complete for various equipments with galvanised steel earth plate electrode 600 x 600 x 6mm thick directly burried in the ground (earth pit not less than 2.25 metre deep below ground level) with top edge of earth plate not less than 1.5 m below the ground level, connected to G.I wire 4 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, GI pipe 20mm bore light grade for protection of earthing strip, PCC chamber 1:4:8, type C-1 using 20mm graded stone aggregate, internal surface of concrete chamber plastered with 12mm thick plaster in CM 1:4, funnel with wire gauge of 22 gauge ( 0.63) 8 mesh per linear inch, 50mm thick cover of RCC 1:2:4, type B-1, using 20mm graded stone aggregate, reinforced with 8mm TMT bar at 100mm center to center both ways and charcoal dust and common salt all as shown in electrical plate No. 3 of MES SSR Part-I and as specified including excavation and earth work and connecting the earthing to an earthing test point as specified and testing on completion all as directed.

Schedule of credit amount of Rs. 0.00 to be deducted during AOC

m/s R K SETHI

M/S. HONEY CONSTRUCTIONS