REPAIRS TO BRICK WORK, JOINERY, PAINTING, PLUMBING WORK, PATHWAYS, HARD STANGING, WALL, DRAINS, FENCING, SEWAGE CLEANING AND OTHER MISC REPAIRS IN RR UNITS UNDER ZONE -I AND III AT DHARMUND AREA UNDER AGE (I) BHALRA

Amount

Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified.

Demolition of cement concrete in ground floors and paving not exceeding 15cm thickness (below or above ground level) un-reinforced, complete all as specified.

Demolition of reinforced cement concrete of any description in any position not otherwise specifically provided for (Reinforcement cut as required to facilitate demolition), complete all as specified.

Taking down cement plaster on brick or stone or concrete surfaces etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each, complete all as specified.

Taking down shutters of any description exc. 1 sqm and not exc. 2 Sqm each, complete all as specified.

Taking down, easing and adjusting shutters of any description, exceeding 1.00 Sqm and not exceeding 2.00 sqm each and re-fixing in the same or other opening, complete all as specified.

Material and labour for brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:6, complete all as specified.

All as per Srl item No. 09 here-in-before but except bricks.

Material and labour for stone walling of random rubble with best quality locally available harder stone such as granite, trap or basalt, brought upto courses, well bonded, bedded, solidly hearted and built in cement mortar 1:6, complete all as specified & directed.

All as per Srl item No. 11 above but except stone.

Extra over stone walling of granite, trap or basalt stone for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses with maximum depression on face from straight edge held against the dressed surface n exc 40mm, complete all as specified & directed.

Material and labour for raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortar 1:4, complete all as specified.

Material and labour for Hand packing (any thickness) using broken stone or boulders at back of walls over arches etc., and raising (or lowering) to the required level, complete all as specified.

Material and Labour for plain cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified.

Material and Labour for Extra for forming fair finished drain or channel 60cm inner girth in cement concrete using extra cement including necessary form work complete all as specified.

Supply and fixing of 1.25mm thick pressed steel frames with one shop coat of red oxide primer 105 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate, including cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in filling hollow of frame with plain cement concrete and hold fast after tearing of hollow portion of frame complete all as specified and directed.

Supply and fixing of 1.25mm thick pressed steel frames with one shop coat of red oxide primer 125 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate, including cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in filling hollow of frame with plain cement concrete and hold fast after tarring of hollow portion of frame complete all as specified and directed.

Supply and fixing of Factory made Glazed and skelton shutters 35mm thick of 2nd class hard wood rail & style open rebated and prepared to receive glass or wire gauze etc. shutters (without shash bars), size of members of shutters as specified in SSR Part-1, secton 8, clause 8.24(a) kiln seasoned and pressure treated all as specified.

Supply and fixing of Plain framed factory made 35mm thick shutter of 2nd class hard wood rail & style (two panel) with lock rail and panel of 9mm BWP commercial plywood or 12 mm veneered particle board with commercial veneering on both faces , the size of rail and style as per IS 1003 (Part-1) kiln seasoned and pressure treated, fitted to chowkats, complete all as specified.

Supply and fixing of 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified.

Supplying and fixing of factory made Solid PVC Door Frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S.Square tube, suppling & fixing in opening as per specification complete all as specified and as directed.

Supplying and fixing of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing all as specified and as directed.

Supply and fixing of 100mm long medium weight butt hinges, stainless steel with SS hinge pin and fixed, complete all as specified.

Supply and fixing of Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or excluded sections and fixing bolts and sliding bolts of excluded sections or cast aluminum alloy and fixed, 300mm long, complete all as specified.

Supply and fixing of 200mm long aluminium anodised, barrel tower bolt of extruded section and fixed, (ISI marked), complete all as specified.

Supply and fixing of 150mm long aluminium anodised, barrel tower bolt of extruded section and fixed, (ISI marked), complete all as specified.

Supply and fixing of 125mm long extruded aluminium alloy handle, fabricated type, anodised, (ISI marked), complete all as specified.

Supply and fixing of Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm, complete all as specifed.

Supply and fixing of Mild Steel, 300mm, ordinary rat tail rod pattern springs including roller and roller plate fixed with screw or necessary welding to pressed steel door frame, complete all as specified.

Supply and fixing of stainless steel wire cloth 0.36 nominal dia of wire and average width of aparture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified.

Supply and fixing in repair stainless steel wire cloth 0.36 nominal dia of wire and average width of aparture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified.

Supply and fixing of 3 mm thick sheet glass, ordinary quality & glazing with oil putty around the glass in square n exc 0.5 sq.m in each pane, complete all as specified and as directed.

Supply and fixing of Steel windows with side hung shutters including box type hinges with steel handle 100mm long, made of Z section and steel peg stay, complete with glazing bars, dovetailed or welded including one shop coat of red oxide zinc crome primer and two numbers MS tower bolt of 100 mm long, complete all as specified & directed.

Supply and fixing in repair 20mm outer dia stainless steel decorative curtain rod of thickness 20 guage with stainless steel brackets near to ends with stainless steel finials with adopter for 20mm dia curtain rod at both ends, complete all as specified.

Taking up or down steel water tubing and connections 15mm bore including cleaning for refixing or removing to store complete all as specified and directed.

Supply and fixing of 15mm dia GI steel water tubing, medium grade ISI marked, with and incl all fittings such as bends, elbows, tees, short pieces, diminishing pieces, union etc complete to walls and ceilings or laid in floors complete all as specified.

Taking up or down steel water tubing and connections 20mm bore including cleaning for refixing or removing to store complete all as specified and directed.

Supply and fixing of 20mm dia GI steel water tubing, medium grade ISI marked, with and incl all fittings such as bends, elbows, tees, short pieces, diminishing pieces, union etc complete to walls and ceilings or laid in floors complete all as specified.

Fixing only 20mm GI tubing in new or old position, any grade, to walls and ceilings or laying in floors including necessary fittings & fixtures etc complete all as specified and directed.

Supply and fixing of Rotational moulded polythene water storage tank, white coloured, tripple layer cylindrical vertical with closed top 500 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug and PTMT ball valve 20mm (Minimum weight 210gms), high pressure with polyethelyne float and fly nuts including taking down old complete all as specified and directed.

Supply and fixing of Rotational moulded polythene water storage tank, white coloured, tripple layer cylindrical vertical with closed top 1000 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug and PTMT ball valve 20mm (Minimum weight 210gms), high pressure with polyethelyne float and fly nuts including taking down old complete all as specified and directed.

Supply and fixing of Stop valves, cast copper alloy, 20mm bore, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., fixed in repair, complete all as specifed

Supply and fixing of stop valves, 15mm bore, fancy type, chromium plated with long shank and cup (concealed type), cast copper alloy, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., fixed in repair, complete all as specifed.

Supply and fixing of 15mm bore Bib taps long body (ISI marked) of cast copper alloy chromium plated, fancy type, screwed down, high presure, screwed both ends for iron pipe or for brass ferrule, fixed in repairs complete all as specified and directed.

Supply and fixing of Angle valve/Stop valve of cast copper alloy chromium plated (ISI marked), fancy type, screwed down high pressure, screwed both ends for iron pipe or for unions 15 mm bore, fixed in repairs complete all as specified and directed.

Supply and fixing of Pillar tap cast copper alloy with capstan head, fancy type, chromium plated (ISI marked), screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed shank and fly nuts screwed for iron pipe complete for 15mm bore pipe, fixed in repairs all as specified & directed.

Supply and fixing of shower rose brass chromium plated 200x200mm size with flexible brass arm 450-550mm long for 5mm bore pipe, fixed in repairs, complete all as specified and directed.

Supply and fixing of soap dish cantabile-clea (material SS finish, glossy) fixed to plugs with chromium plated brass screws and wooden/plastic cleats, fixed in repairs, complete all as specified.

Supply and fixing of Vitreous Chinaware squatting pan, orissa pattern size 580mm x 440mm with integral foot rests, white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, including provision of cement concrete, making connections to trap and to flush pipe etc. and making good to floors, fixed in repairs, complete all as specified.

Supply and fixing of Vitreous China wash down water closet (Pedestal pattern), white with ‘P’ or ‘S’ trap, fixing with screws of suitable size, plastic seat cover, white closed pattern with flat bottom and cover, complete all as specified, making connections to trap and to flush pipe, fixing flushing cistern etc. and making good to floors, fixed in repairs, complete all as specified.

Supply and fixing in repair CP brass hand shower (Health faucet) with 8mm dia, 1.25 metre long flexible tube chrome finish & wall hook including making connections and fixed in position, complete all as specified and directed.

Supply and fixing of CP brass towel ring 20mm dia, fancy type, superior quality, fixed with and including chromium plated screws and wooden/plastic cleats, fixed in repair, complete all as specified.

Supply and fixing of centre hole CP brass basin mixer without popup waste system with 450mm long braided hoses cast copper alloy for iron pipe 15m bore, screwed for iron pipe and fixed in repair, complete all as specified and directed.

Supply and fixing of push button type dual flush type PVC valve less syphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and push button including brackets and 32mm dia PVC flush pipe for low level cistern all joints fixed in repairs complete all as specified and directed.

Supply and fixing of Vitreous china Wash hand basin, oval shape counter sunk, white, size 550x400mm including vitreous china pedestal and cast iron brackets, cutting for and pinning in ends of brackets or erecting stand etc. including brass chromium plated waste coupling with long screwed shank and fly nuts, PVC flexible waste pipe of bore 32mm, fixed in repair, complete all as specified and directed.

Supply and fixing of Viterous China urinal, half stall type, white (minimum) with grating and union for discharge pipe, complete including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement including 32mm bore PVC waste pipe, fixed in repairs, complete all as specified.

Supply and fixing of 32mm dia, low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc., fixed in repairs complete all as specified.

Supply and fixing of CP brass tubular towel rail, 20mm dia, D type, 60cm long between flanges, fixed in repairs, complete all as specified and directed.

Supply and fixing of PVC connection 15mm size with brass nuts on both ends of length 450mm, fixed in repairs complete all as specified.

Supply and fixing of PVC (SWR) floor trap of 75mm dia of outlet, plain with grating including jointing with solvent cement, fixed in repair, complete all as specified.

Supply and fixing of PVC grating 150x150mm square (hinges pattern and with or without hole), complete all as specified.

Dismantling of old/broken cast iron pipes of any dia from existing lines fixed to wall with clamps or taking out of trenches, complete all as specified and directed. Note: Rate Quoted demeed to be including for excavation required for taking out of pipe from tranches.

Supply and fixing of PVC (SWR) 110mm dia any length single socketed with rubber ring joint, trenches or floor and fixed to walls, fixed in repair, complete all as specified and directed.

Supply and fixing of 110mm bore PVC (SWR) bends any radius with or without excess door, complete all as specified.

Supply and fixing of PVC (SWR) 75mm bore vent cowl, complete all as specified.

Supply and fixing of PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint, laid in trenches or floor and fixed to walls, fixed in repair, complete all as specified and directed.

Supply and fixing of 75mm bore PVC (SWR) bends any radius with or without excess door, complete all as specified.

Material and Labour for jointless non skid ceramic coloured tiles 7 to 8mm thick (Square/Rectangular) area exceeding 0.18 sqm but not exceeding 0.36 sqm in floors set and jointed in neat cement slurry over 15mm thick screed bed in CM (1:6) jointed in neat cement slurry and pointed in coloured cement including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles from site and rubbish off the premises, complete all as specified and directed.

Material and Labour for jointless non skid ceramic coloured tiles 7 to 8mm thick (Square/Rectangular) area exceeding 0.18 sqm but not exceeding 0.36 sqm in skirting/dado etc set and jointed in neat cement slurry over 10mm thick screed bed in CM (1:4) jointed in neat cement slurry and pointed in coloured cement including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles from site and rubbish off the premises, complete all as specified and directed.

Material and Labour for jointless non skid ceramic coloured tiles 7 to 8mm thick (Square/Rectangular) area exceeding 0.11 sqm but not exceeding 0.18 sqm in floors set and jointed in neat cement slurry over 15mm thick screed bed in CM (1:6) jointed in neat cement slurry and pointed in coloured cement including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles from site and rubbish off the premises, complete all as specified and directed.

Material and Labour for Glazed ceramic coloured tiles in skirting/dado 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match required shade over 10 mm thick cement plaster in cement mortar 1:4 as backing coat rough finished surface including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles from site and rubbish off the premises, complete all as specified and directed.

Material and Labour for Vitrified light shade Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM (1:6) jointed in neat cement slurry and pointed in coloured cement including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles from site and rubbish off the premises, complete all as specified and directed.

Material and Labour for Vitrified light shade Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM (1:6) jointed in neat cement slurry and pointed in coloured cement including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles from site and rubbish off the premises, complete all as specified and directed.

Material and Labour for Granite (of any type) tiles 20mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting & polishing, laid over and including 15mm screed layer in cement mortar 1:4 and rounding/bull nose to expose edge of granite including demolition of stone slab and tiles of any description and thickness in floors, aprons etc laid and pointed in any mortar, complete all as specified & directed.

Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, size of each slab not be less than 55cmx55cm, including 75mm wide white marble border alround and rubbing and mirror polishing complete over and including 20mm thick screed bed in CM 1:6 including demolition of stone slab and tiles of any description and thickness in floors, aprons etc laid and pointed in any mortar, complete all as specified & directed.

Material and Labour for Kota stone slab 16mm thick in riser of steps, skirting, dado and pillar over and including 10 mm thick cement plaster in cement mortar 1:4 as backing coat rough finished surface, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing including demolition of stone slab and tiles of any description and thickness in floors, aprons etc laid and pointed in any mortar, complete all as specified & directed.

Material and Labour for 40mm thick plain cement concrete 1:2:4 type B-1 (20mm graded crushed aggregate) as in floors finished even and fair, complete all as specified and directed.

Material and Labour for chequered cement concrete tile 300mmx300x25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment as in floor including over 20mm screed bed in cement mortar 1:4, complete all as specified and directed.

Material & labour for 75mm thick plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base, complete all as specified and directed.

Material and labour for Rendering 10mm thick cement plaster on other than fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for Rendering 15mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:4) in two layers (5mm finishing layer over 10mm base layer) finished even and fair without using extra cement with WPC @ 200ml/bag of cement over finishing layer complete all as specified and directed.

Material and labour for 75 mm thick plain cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in plinth protection and laid in panels complete and finished the even & fair and providings joints through out the thickness of plinth protection filed with mastic filling comprising one part of 01 bitumen 85/25 grade and three part of sand by weight all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coat of oil bound distemper white or tinted over a coat of chalk whitening, complete all as specified and directed.

Material and labour for complete removal of existing treatment of wall surfaces and applying two coat of oil bound distemper white or tinted over a coat of chalk whitening, complete all as specified and directed.

Material and labour for preparing new surfaces (plastered or unplastered) of walls and applying two coats of cement base paint white or tinted including curing before and after paint, complete all as specified and as directed.

Material and labour for preparation of old decorated plastered surfaces of walls of any description washing down, rubbing down, brooming down with wire brush, scrapping down smoke, roots, moulds, moss and effloresnt salt and trading oil or greasy spots including taking down existing grass, vegetation, small trees and making good the disturbed surface with cemnet mortar 1:3 and applying one coats of cement base paint including curing before and after paint, complete all as specified and as directed.

Material and labour for preparation of new plastered surface of wall and applying three coats of white wash, complete all as specified and directed.

Material and labour for preparation of old plastered surface of wall and applying two coats of white wash, complete all as specified and directed.

Material and labour for preparation of new or previously untreated steel and iron surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified.

Material and labour for preparation of old painted surface of steel and iron surfaces of any description, over 10cm width or girth and applying one coats of synthetic enamel paint, complete all as specified.

Material and labour for preparation of new or previously untreated wood surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified.

Material and labour for preparation of old painted surface of wood of any description not otherwiae described over 10cm width or girth and applying one coats of synthetic enamel paint, complete all as specified.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering or in ridges, hips, valley gutter and similar work, complete all as specified.

Dismantling timber scantling 40 Sqcm and over in section, in any position (unframed work), complete all as specified.

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified.

Material and labour for PCC 1:2:4, type B-1, using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified.

Material and labour for rolled mild steel work in roof trusses (framed) trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-290(Gde E-165), complete all as specified & directed.

Supply and fixing of Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified.

Supply and fixing of Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified.

Supply and fixing of 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap at least 150mm end lap, fixed with galvanized L-type or J- type or cranked hook bolts in lieu of screw of sheet, 8mm dia with bitumen and G.I limpet washers filled with white lead, in roofs, walls etc. with grade of zinc coating 275, complete all as specified.

Supply and fixing of 0.63mm thick galvanised, plain mild steel sheeting in ridges, hips, valley gutter, drip and straight flashing with grade of zinc coating 275, complete all as specified.

Dismantling of wall and ceiling boards (fibre, pulb, insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets, complete all as specified and directed.

Supply and fixing of 4 mm thick non asbestos fiber cement plain building boards in false ceiling on and incl aluminium snap grid work 605 x 605 mm with using 36.5mm x 23.5 mm x 1.5 mm thick main tee, 23.5 x 23.5mm x 1.28 mm cross tee and 25x25x1.5mm angles fixed to perimeter of wall including necessary supporting hanger with 4 mm dia GI wire and J bolts washer nuts for securing frame work to ceiling suspended @ 120 cm c/c both ways, complete all as specified and directed.

Supply and fixing of PVC wall panelling made up of PVC hollow panels 25/30cm in width and 10mm thickness interlocking pattern of approved shade and design fixed to wall or ceiling all as specified and directed.

Supply and fixing of 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed.

Material and labour for mild steel TMT bars 10mm dia and over cut to length, bent to shape, required including cranking, bending, spirally for hopping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Material and labour for use & waste of form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete, complete all as specified & directed.

Material and labour for taking down existing aluminium door/window and refixing to the same opening after repairing, easing and adjusting including replacement of damaged hinges, brass mortice lock, sheet glass, door closer, Elco panel, floor spring, rubber neoprene packing, aluminium beading, glazing clips and SS screws complete all as specified and directed. Note: Mortice lock, sheet glass, hydraulic door closer, floor spring and composit panel to be measured and paid seperately under respective items as supply only.

Supply and fixing of powder coating of any colour (thickness or powder coating not less than 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified complete all as specified and directed.

Supply and fixing of powder coating of any colour (thickness or powder coating not less than 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified, complete all as specified.

Supply and fixing of powder coating of any colour (thickness or powder coating not less than 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

Supply only Door closure hydraulically regulated designation No. 1 universal type of aluminium (die cast) body, suitable for door shutters of 750mm in width and of weight between 35 Kilogam, complete all as specified and as directed.

Supply only sheet glass ordinary quality, 4.8mm thick, fitted with aluminium snap bedding and rubber gasket in aluminium doors/windows exceeding 0.50 Sqm in each pane, complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from from metal frame including punching or drilling out old glazing pins/spring clips and providing & fixing new ones exc 1.5 sqm, complete all as specified.

Supply only Aluminium mortice lock, 4 lever, vertical type, size 100 mm, complete in all respect as specified.

Supply only Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specified.

Supply only 4mm thick aluminium composite panel for fixing to aluminium shutter and the like square with aluminium beading/gaskets, complete all as specified.

SAHIL PROCH (BID ID -3157132)