Repair/Maintenance of External Water supply line all types of Pump sets and other allied works at Mil Stn Beas and Jandiala Guru under GE Kapurthala

Amount

Excavation in trenches in soft/loose soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for taking out and laying CI/GI pipe complete all as specified and directed by Engr-in-Charge.

Returing, filling in, including spreading, leveling watering and well ramming inlayers not exceeding 25 cms thick each layer complete all as specified and directed by Engr-in-Charge.

Removal of surplus spoil to a distance not exceeding 50 mtr away and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed by Engr-in-Charge.

Taking down old unserviceable GI/CI pipe 80 mm bore and supply, laying, jointing and testing new cast iron pipe 80 mm bore centrifugally cast class LA confirming to IS - 1536 spigot and socketed ends in any length laid in trenches complete all as specified and directed by Engr-in-Charge. (Note : Excavation, earth work, CI fitting and new run lead joint shall be measured and paid for separetely under appropriate item of Sch 'A')

All as per item No 4 above here in before but 100 mm bore, complete all as specified and directed by Engr-in-Charge.

All as per item No 4 above here in before but DI (K-7)100 mm bore, complete all as specified and directed by Engr-in-Charge.

All as per item No 4 above here in before but 150 mm bore, complete all as specified and directed by Engr-in-Charge.

All as per item No 4 above here in before but DI (K-7) 150 mm bore, complete all as specified and directed by Engr-in-Charge.

M&L for disconnecting electric connection and pipe connection and taking out submersible pump & motor of capacity 12.5 to 17.5 HP from bore well and taking to workshop for repair and removal of burnt winding wire from motor and rewinding with new PVC insulated copper winding wire for submersible motor of same guage and weight to existing including replacement of, Motor bush, thrust plate coupling complete with key and alignment of motor stater's slote reassembnling the motor with pump and lowering it into bore well making it functional and testing complete all as specified and directed by Engr-in-Charge.

All as per item 9 above here in before but capacity 25 to 30 HP, complete all as specified and directed by Engr-in-Charge.

All as per item 9 above here in before but capacity 35 to 45 HP of turbine motor pump including replacerment of ball bearings, complete all as specified and directed by Engr-in-Charge.

All as per item 9 above here in before but capacity 100 HP of turbine motor pump including replacerment of ball bearings, complete all as specified and directed by Engr-in-Charge.

M&L for disconnecting submersible pump from electric motor and taking it to work shop for repair/replacment of unserviceable part of submersible pump capacity 12.5 to 17.5 HP such as gun metal bush impeller assembly remetaling/ turning to shaft, locking key and MS nuts & bolts of existing size and reassembling the pump with motor and making it functional complete all as specified and directed by Engr-in-Charge.

All as per item 13 above here in before but capacity 25 to 30 HP, complete all as specified and directed by Engr-in-Charge.

All as per item No 13 here in before but for submersible pump for capacity 35 HP to 45 HP, complete all as specified and directed by Engr-in-Charge.

All as per item No 13 here in before but for submersible pump for capacity 100 HP, complete all as specified and directed by Engr-in-Charge.

S&F Submersible pump set, Electric driven having dischage 1000 LPM at 84 mtr head including suitable capacity of electric motor not less than 45 HP suitable for operation of 415 volts 50 C/S AC supply complete all as specified and directed by Engr-in-Charge.

S&F Submersible pump set, Electric driven having dischage 1000 LPM at 84 mtr head including suitable capacity of electric motor not less than 15 HP suitable for operation of 415 volts 50 C/S AC supply complete all as specified and directed by Engr-in-Charge.

M&L for repairs & servicing of centrifugal pump & Motor sets 100 HP (Make : BATLIBOI), electric driven Squirrel cage induction motor 3 phase 415 V AC 50 HZ,opening & cleaning inside of 100 HP motor stator, varnishing and drying, re-winding and duly replacing the following worn out parts of pump and re-erecting, testing & commissioning complete all as specified and directed by Engr-in-Charge. (a) Bearings (b) coupling bolts (c) coupling rubber bush (d) split casing gaskets (e)shaft sleeves (f) replacing the air cocks grease nipple etc (g) painting the pump & Motor with one coat synthetic enamel grey colour paint (Fire Pump House No 1 & 2).

M&L for repairs and servicing of Jocky pump & Motor Set (Make : Crompton Greaves)electric driven Squirrel cage induction motor 3 phase 415 V AC 50HZ opening & cleaning inside of 15 HP motor stator varnishing and drying ,re-winding and duly replacing the following worn out parts of pump and re -erecting, testing and commissioning complete all as specified and directed by Engr-in-Charge. (a) Bearings (b)coupling bolts (c) coupling rubber bush (d)split casing gaskets (e)shaft sleeves (f) replacing the air cocks grease nipple etc (g) painting the pump & Motor with one coat synthetic enamel grey colour paint. (Fire Pump House No1 & 2).

Repair/Replacment of unserviceable part of submersible pump capacity 25 to 30 HP such as gun metal bush impeller assembly remetaling/turning to shaft, locking key and MS nuts & bolts of existing size and reassembling the pump with motor and making it functional, complete all as specified and directed by Engr-in-Charge.

All as per item No 21 here in before but for submersible pump for capacity 35 HP to 40 HP, complete all as specified and directed by Engr-in-Charge.

All as per item No 21 here in before but for submersible pump for capacity 10 HP to 20 HP, complete all as specified and directed by Engr-in-Charge.

All as per item No 21 here in before but turbine pump of capacity 45 to 100 HP, complete all as specified and directed by Engr-in-Charge.

S&F Submersible pump set, Electric driven having dischage 1000 LPM at 84 mtr head including suitable capacity of electric motor not less than 30 HP suitable for operation of 415 volts 50 C/S AC supply, complete all as specified and directed by Engr-in-Charge.

S&F PVC insulated submersible cable 03 core 1100 Volt AC supply stranded copper conductor of size 10 sqmm in replacement of old unsv cable, complete all as specified and directed by Engr-in-Charge.

S&F PVC insulated submersible cable 03 core 1100 Volt AC supply stranded copper conductor of size 16 sqmm in replacement of old unsv cable, complete all as specified and directed by Engr-in-Charge.

M&L fo painting of Over head Rising main and delivery line of two colour code, Rising main blue colour and delivery line black colour with Arrow mark for mention rising and distribution line, complete all as specified and directed by Engr-in-Charge. Note:- Complete pipe line of one Over head tank with Sluice valves are count one unit.

S&F in replacement of old unsv water level indicator devies electronic type including PVC copper cable 0.5 Sqm of 10 core and water sincer 07 No with copper PVC cable as required as per site complete all as specified and directed by Engr-in-Charge.

S&F in replacement cast iron fitting such as bends, tapers (any type, radius & angle) tapers any type,(straight, bend, increasing,decreasing or double socket etc.) Tee pieces single branch. "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs tee pieces, single branch for spigot and socket and flanged pipe up to 150 mm bore complete all as specified and directed by Engr-in-Charge.

S&F in replacment cast iron sluice valve 80 mm bore with flanged ends with Gun metal spindle, CI gate with brass ring and iron wheel handle with jointing material such as nuts /bolts washers and rubber insertion sheet etc including taking out old unsv sluice valve complete all as specified and directed by Engr-in-Charge.

All as per srl item No 31 here in before but 100 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per srl item No 31 above here in before but 150 mm bore, complete all as specified and directed by Engr-in-Charge.

S&F in replacement unserviceable fully automatic star delta starter in sheet steel enclousure type ML-2 FASD 3 phase 440 volt 50 Hz of capacity 35 HP, complete all as specified and directed by Engr-in-Charge.

M&L for replacment existing cast iron double air release valve of size 80 mm bore replacment of worn out bolts, nuts gaskets if any complete all as specified and directed by Engr-in-Charge.

Repair to existing valve pits of internal dimensions 90cm x 90 cm x 90 cm making good disturbed/dismantled brick work in cement mortar (1:4) plastering surfaces in CM 1:6, 15mm thick and PCC coping in cement concrete 1:2:4 type B-1 and providing MS cover in replacement made out of MS sheet 3 mm thick duly welded to MS angle iron frame 35x35x5mm including frame work as per existing size with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge. (a) M&L for brick work using sub class 'B' (old size bricks) in CM 1:4 (b) M&L for rendering 15 mm thick in CM 1:4 finishing even and fair (c) M&L for PCC 1:2:4 type B-0 (using cum 12.5 mm graded stone aggregate ) as in coping (d) M&L for any type of mild steel work such as frame sheet 3 mm thick including welding (e) M&L for painting two coats of synthetic enamel paint over a coat of red oxide primer to untreated steel surface & prep of surface.

All as per srl item No 36 above here in before but size 75 x 75 x 75 cms, complete all as specified and directed by Engr-in-Charge.

M&L for cleaning & flushing of RCC over head reservoir of capacity 25000 gallons at 60 feet staging removing of silt and sludge etc deposited inside the tank and cleaning of entire internal surfaces of tank with bleaching powder incl flushing with water, writing the capacity of tank and date of cleaning with black and white paint, size of text complete all as specified and directed by Engr-in-Charge.

All as per srl item item No 38 here in before but reservoir of capacity 4000 gallons at 14 feet staging, complete all as specified and directed by Engr-in-Charge.

M&L for cleaning & flushing of Static water tank cuboid/circular in shape of capacity 50000 gallons and the depth of 5 feet , and removing of silt and sludge etc deposited inside the tank and cleaning of entire internal surfaces of tank with bleaching powder incl flushing with water, writing the capacity of tank and date of cleaning with black and white paint, size of text complete all as specified and directed by Engr-in-Charge.

All as per item No 40 here in before but SWT of capacity 15000 gallons and the depth of 4.5 feet, complete all as specified and directed by Engr-in-Charge.

S&F phase sequancer corrector with phase loss corrector system working on 415 Volt, 50 Hz, On/Off coil (switch) current capacity 18A, working voltage 12/24 Volt, Cut of voltage (Low) 330-370 (Adjustable), cut of voltage (High) 440-540 Voltage (Adjustable), Phase reversal System, Single phasing protection system, Time delay to start system 150 sec and Off switching time (two stop the system) for 10 HP submersible pump etc complete all as specified and directed by Engr-in-Charge.

All as per item No 42 here in before but current Capacity 32A, 25 HP, complete all as specified and directed by Engr-in-Charge.

All as per item No 42 here in before but current Capacity 40A 30 HP, complete all as specified and directed by Engr-in-Charge.

All as per item No 42 here in before but cuurent Capacity 50A 40 HP, complete all as specified and directed by Engr-in-Charge.

Taking down old unsv bleching dozing pump along with all accessories and Supply and install connecing. Testing and commissioning of High Pressuure single Head adjustable "DECLIBAC" Dosing system Model No VST 1005 and VST 1006 of the following specification. Adjustble High Pressure 5 Kg/Sq. cm. power input 230V, 50 Hz, 40 SPM 1/30 fractional Horsepower, Max output 10 Ltr with mandatory accessories like lead Tubing, connecting ferrules, check valves, etc complete all as specified and directed by Engr-in-Charge. (A) Preparation tank Model No VST 1005 of net capacity 100 Ltr, FRP dosing tank dia 650 x net Height 375 + conical 300. Gross height with stand 1000 mm consisting of : (i) Water inlet line (ii) Outlet with stainer (iii) Drain (iv) overflow (v) conical bottom for sludge depositing (vi) Pot hole with cover (vii) level gauge (viii) Agitator 120 watt 900 RPM single phase flange mounted motor with plastic shaft and impeller. (B) Service Tank Model No VST 1006 dia 480 x height 575 net capacity 100 Ltr consisting of (i) water inlet line (ii) Dosing pump inlet arrangement (iii) Drain (iv) Overflow (v) Level Gauge (vi) inspection port (vii) Agitator 120 watt 900 RPM Single Phase flange mounted moto with plastic shaft and impeller (ix) provision of mounting Pump on Lid/wall.

S&F battery 12 volts 180AH, complete all as specified and directed by Engr-in-Charge.

M&L for replacement on load change over rotary type 4 pole 415 volt 200 Amp, complete all as specified and directed by Engr-in-Charge.

Supply only orthotolidine reagenet for chlorine test in 500 ml bottle, complete all as specified and directed by Engr-in-Charge.

Supply only Calcium based granuler disinfect suitable for treatment drinking water in 45 kg plastic drum complete all as specified and directed by Engr-in-Charge.

S&F aviation light LED type fixed on the top of OHT of any height including necessary fixing accessories complete all as specified and directed by Engr-in-Charge.

S&F CI double flanged Non -return valve (150mm dia bore), class 'B', High pressure PN 1.6, including bolts, nuts, washer and rubber packing complete all as specified and directed by Engr-in-Charge.

All as per item No 52 above here in before but 100 mm bore dia, complete all as specified and directed by Engr-in-Charge.

Material labour and services for taking sample water in sterlised bottles from various borewells for Analysis of water for the following parameters and obtaining sample test report from Govt Recognized Laboratories: (i) Physio Chemical Analysis of Water ( Colour , odour , pH Total solids, Dissolved Solids, Permanent hardness, temporary Hardness, Ammonia feree and salinbe, Ammonia Albuminoidal, Nitrites, Nitreates, Oxygen absorption at 15 Min, Iron , Fluoride) (ii) Microbiological Analysis ( Totral Choliforms , Eschirrchea Coli) Note : 1. A certificate of approval / certification of Lab by Goivt Of India / State Govt shall be submitted by the contractor to the deptt. 2. Sample shall be submitted to the Labortory within 24 Hrs of collection of sample.

Supply of Chlorine test kit with coloured ample complete with all testing fitments and OT solution in Rexene finish Box, complete all as specified and directed by Engr-in-Charge.

Taking down old u/s star delta starter Panel and Supply , install, testing and commissioning of fully automatic star delta starter Panel with all accessories in sheet steel enclosuer, 3 phase 440 volt, 50 Hz ,suitable for 25 HP submersible motor including incoming /outgoing cable connections and fixing arrangment, mounting on floor with suitable size of angle iron frame and legs complete all as specified and directed by Engr-in-Charge.

S&F GI coloumn pipe 100mm dia heavy duty 'C' class with flanged ends drill 3 meter including joining to exising main pipe line complete all as specified and directed by Engr-in-Charge. Note:- The cost of nuts bolts washers packing materials and pressure gauge shall be deemed to include in unit rate quoted by the contractor.

M&L for lead joint suitable for CI pipe 80 mm bore complete for laying of new pipe line including rectification of leakage pipe line on daily, complete all as specified and directed by Engr-in-Charge.

M&L for lead joint suitable for CI pipe 100 mm bore complete for laying of new pipe line including rectification of leakage pipe line on daily complete all as specified and directed by Engr-in-Charge.

M&L for lead joint suitable for CI pipe 150 mm bore complete for laying of new pipe line including rectification of leakage pipe line on daily, complete all as specified and directed by Engr-in-Charge.

Developing the borewell for six hours with air compressor machine of capacity 250 PSI and 550 Cfm till clear water is obtain from the borewell and all the blocked stainers are opened up to depth of 300 feet and again relowering the pump set along with column pipe, complete all as specified and directed by Engr-in-Charge.

Lowering of submersible pump set with column pipe of 100 mm dia, 3 mtr long-12 Nos with required T&P and man power, complete all as specified and directed by Engr-in-Charge.

Supply and filling pea gravel of size 3 to 10 mm to a packed thickness into the side of existing bore well (which is hollow space between casing pipe and true bore) complete all as specified and directed by Engr-in-Charge.

S&F Ammeter, Square type, 0-200 Amps, complete all as specified and directed by Engr-in-Charge.

All as per item No 64 above here in before but 0-100 Amps, complete all as specified and directed by Engr-in-Charge.

All as per item No 64 above here in before but 0-60 Amps, complete all as specified and directed by Engr-in-Charge.

S&F volt meter, Square type, 0-500 volts, complete all as specified and directed by Engr-in-Charge.

Supply only gland packing of size 10 mm to 16mm, complete all as specified and directed by Engr-in-Charge.

M&L for replacment of pressure gauge 0-100 PSI, dial type fixed on pumping line in various pumps, complete all as specified and directed by Engr-in-Charge.

Supply, install, testing and commissioning of Star Delta starter panel capacity 45 HP panel size 90cm x 60cm x 40cm enclosures cubical weather and vermin proof totally enclosed made out of 2mm thick CRCA sheet machine pressed of suitble size to operate on 3 Phase 4 wire system 415 Volts, 50 HZ double door with front openable with locking arrangement incl inner shutters for mounting switch gear etc, bottom Gland plate with sufficient numbers of circular cable entery holes, including PCC work, prewired complete duly powder coated with comprising of the following:-

Taking down existing old unsv LT panel & Supply, install, testing and commissioning of LT distribution panel, CPRI approved, weather/vermin proof, made out of 3 mm thick CRCA sheet, factory assembled cubicle pattern modular and compartmentalized construction, outdoor type, with front and backside hinged double door with locking arrangement, floor mounted free standing type, duly powder coated, 3 phase and neutral 630 amps current carrying capacity aluminium bus bar with epoxy insulated coating with colour code and insulated support with aluminium earth bus of size 25x3mm with terminal switch, cable galleries, inter connecting bus bar connection/linkage, complete with the following switch gears and mounting the panel board on ground with PCC (1:2:4) type B-1 using 20mm graded stone aggregate bedding upto a height of 45 cm above gorund level, complete all as specified and directed by Engr-in-Charge and comprising the following :- (a) MCCB 4 Pole, 415 V, Adjustable type, 400 Amps with breaking capacity 36 KA- 01 No (In Coming). (b) MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 36 KA- 02 No (out Going) (c) MCCB 4 Pole, 415 V, Adjustable type, 200 Amps with breaking capacity 36 KA- 02 Nos ( Out going) (d) MCCB 4 Pole, 415 V,Adjustable type, 100 Amps with breaking capacity 36 KA- 04 ( Out going) (e) Digital Volt Meter 0-500V - 01 No. (f) Digital Ampere Meter 0-500 A with 3 Nos of CTs. (g) Indicator LED type

Taking down existing old unsv Star Delta starter panel & Supply, install, testing and commissioning of Star Delta starter panel, (not less than 180cmx150cmx40cm), CPRI approved, weather/vermin proof, made out of 2 mm thick CRCA sheet, factory assembled cubical pattern modular and compartmentalized construction, outdoor type, with front and backside hinged double door with locking arrangement, floor mounted free standing type, duly powder coated, 3 phase & neutral 400 Amps current carrying capacity aluminium bus bar with epoxy insulated coating with colour code and insulated support with aluminium earth bus of size 25x3mm with terminal switch, cable galleries, inter connecting bus bar connection/linkage,prewired complete and mounting the panel board on ground with PCC (1:2:4) type B-1 using 20mm graded stone aggregate bedding upto a height of 45 cm above gorund level, complete all as specified and directed by Engr-in-Charge & comprising the following :- (i) Coper bus bar 400 Amps capacitor of suitable length insulated heavy heat shrinkable sleeves etc -04 No. (ii) MCCB 250 Amps FP, 415 Volt 35 KA adjustable thermal & adjustable magnetic stting Ics = 100% Icu -01 No (incommer) (iii) Star Delta Starter suitable for 100 HP motor, enclosures cubical of suitable size to operate on 3 Phase 4 wire system 415 Volts, 50 HZ, with sufficient numbers of circular cable entery holes, prewired -02 Nos, and with each Star Delta Starter comprising of , MCCB 200 Amps 3P, 415 Volt 35 KA adjustable thermal & adjustable magnetic stting Ics = 100% Icu -01 No, Power contractor 3 pole 200 Amp (AC 3 duty) AC control different level of power and control contacts, inbuilt 1 No+1 NC auxillary contacts -03 Nos, Thermal overload relay suitable for 100 HP motor, 3 Ph, 415V-01 No

SUNRISE ENGINEERS AND CONTRACTOR