ADDN ALTN AND SPECIAL REPAIR OF 10 BLOCKS (40 QTRS) P TYPE AND 05 BLOCK (40 QTRS) H TYPE AT SHANKAR VIHAR UNDER GE (SOUTH), DELHI CANTT-10

Amount

M & L for Providing and injecting chemical chlorpyrifos emulsifiable concentrate for Post Constructional Anti termite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M & L for Anti termite Treatment of soil under existing floors using chemical chlorpyrifos emulsifiable concentrate @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of reinforcement to facilitate demolition (Balcony Parapet wall) complete all as specified and directed.

M&L for reinforced cement concrete (Design mix) M-25 (20 mm graded stone aggregate) as in fins, fascias,slab, louvres, parapets, and railings exc 60 cm in height, newels, balustrade, and the like complete all as specified and directed.

S&F TMT bars 10 mm dia & over as in reinforcement of columns, beams, RCC, slabs, chajjas, lintels etc cut to length bent to shape required including cranking, bending, spirally hoping for columns, hooking ends and welding the new reinforcement with old steel bars complete all as specified and directed.

S&F 8mm dia TMT bars, cut to length bent to shape required including cranking bending spirally for hoping for columns, chajjas to parapets etc hooking ends and binding with mild steel wire not less than 0.90mm dia complete all as specified and directed.

M&L for Formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, etc.; vertical or to better, fair finishes. complete all as specified and directed.

M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, slab, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

M&L for 50 mm thick (avg) guniting in patches on to the required area on RCC parapets walls, columns, beams, stairs, lintels, sunshades, roofing slab etc. of all sizes and shapes at all heights from existing ground floor and all locations with cement and sand mortar 1:3 (1 cement : 3 sand) under 2 to 2.8 Kg/Cm2 pressure after removing the damaged loose spalt concrete portions by chipping, removal of dust and applying one coat of rust convertor kp-100 or equivalent grade over reinforcement wherever necessary providing and tying in position with 75mm x 75mm, square size with 2.946mm dia mild steel wire welded mesh over treated surface ready to receive grouts, curing for 10 days etc, complete operation all as directed including labour charges hire for all tools and plant machineries cost of consumables, scaffolding all types of protective equipments, plant floors, pipelines, vessels, materials etc complete all as specified and directed. Note:(i) After placing the additional reinforcement all concrete surfaces shall be thoroughly scrubbed with brushes, washed with water and allow to dry. To this surface apply chemistic polycrete admixture at the rate not less than 2% by weight of cement or as per manufacture’s instructions. (ii) When polymix coating is in tackey condition guniting is to be done with polycrete admixture at the rate not less than 2% by weight of cement or as per manufacturer’s instruction. Polycrete admixture shall be procured from Chemical Adhesive Pvt Ltd Co or their authorized deale or equivalent. (iii) Cost of the above aspects shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account.

M&L Brick work with sub class "B" bricks , straight or curved on plan exc 6 m mean radius built in CM (1:6),(up to two story Bldg) complete all as specified and directed.

M&L Brick work with sub class "B" bricks , straight or curved on in half brick thick wall built in CM (1:4),(up to two story bldgs) complete all as specified and directed.

Dismantling of brick tiles (laid flat or on edge) on roof surface.laid bedded and pointed in any mortar complete all as specified and directed.

M & L for Demolition of mud in roof, any thickness, including plastering and leeping upto two storey bldg incl necessary scaffolding arrangement complete all as specified and directed(whether full thickness removed or only a part there of) and removing from cantonment area complete all as specified and directed.

M&L for Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in roof pedding , finished even and smooth without using extra cement ,including cleaning the concrete surface by steel wire brushes, up to three stories bldgs, complete all as specified and directed. .

M&L Cement plaster 10 mm thick CM 1:4 with and including water proofing comopound on roof to make surface at level after cleaning PCC surface with water complete all as specified and directed.

M & L for APP polymeric water proofing membrane minimum 3 mm thick and wieghing not less than 3.0 Kg per Sqm , black finish reinforced with non woven polyester matt with a thermo fasable finish laid over bitumen primer @ 0.5Kg/Sqm by torching application with a propane or a butrane gas torch with an overlap of 100mm at the sides and 150 mm at the ends, as per manufacturers instructions complete all as specified and directed

M&L for plain cement concrete tiles with grey cement and no pigment as in roof tiles of size 250 mm x250mm x 20 to22 mm thick laid over 20 mm thick bedding in cement mortar (1:6) and gap between tiles not exceeding 8 mm , grouted up to full thickness of tile with cement mortar (1:3) Mixed with water proofing compound complete all as specified and directed.

M&L for cement concrete type B-1, 1:2:4 (20 mm graded stone aggregate) as in copings, window cills, kerb stone for foot path and similar items with plain fair finishing including chamfers, weathering, throating etc and set in CM 1:4 complete joints to match complete all as specified and directed.

M & L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered and hold fast on edge including necessary form work complete all as specified and directed.

Demolition of stone slab and tiles of any description or thickness on cooking platform, floors, aprons, skirting etc laid bedded and pointed in any morter complete all as specified and directed

M & L for Granite (of any type) work, 18-20 mm thk (table rubbed and polished) in steps, jambs, pillars, cooking platforms, skirtings with necessary hole for gas pipe where ever required and likes on cement mortar bedding of 20mm thick in CM 1:6 including pointing in white cement using marble dust with admixture of pigment to match including rounded edges with shade of granite complete all as specified and directed.

M & L for Machine cut 18-20 mm thick Kota stone mirror polished slab flooring as in treads of staircase over cement screed base 15 mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed.

M & L for Kota stone slab 18-20 mm thick mirror polished in riser of steps, skirting, dado and pillar, including rendering 10mm in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed.

M&L for Udaipur green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, and like including including 20mm thick screed bed in CM 1:6 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for Glazed Ceramic coloured tiles in vertical surface 450X300X7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and including 10mm thick backing coat of CM (1:4), complete all as specified and directed

M&L for Vitrified Ceramic tiles double charged (light shade/ Dark shade), 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15 mm thick in CM 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles double charged (light shade) 10 mm thick (Square/ rectangular) area of each tile not exceeding 0.36 sqm as in skirting laid on 10mm thick cement plaster in CM (1:4) , set and jointed in neat cement slurry at the rate of 3 kg per sqm and pointed in white/coloured cement to match the shade of tiles complete all as specified and directed.

M&L Non Skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick in CM 1:6 complete all as specified and directed.

M&L Non skid ceramic tiles 7 to 8 mm thick( square/rectangular)area of each tile exceeding 0.18sqm but n exc 0.38 sqm, as in skirting laid on 10 mm thick cement plaster in CM (1:4), set and jointed in neat cement slurry at the rate of 3 kg per sqm and pointed in white/coloured cement to match the shade of tiles complete all as specified and directed.

M&L Non Skid ceramic tiles 8 to 10mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick in CM 1:6 complete all as specified and directed.

S&F in repair Vitreous china wash down water closet pan (pedestal pattern) , white fixed in repair,including sheet cover of closed pattern with flat bottom and mild steel chromium plated or aluminiumised hinging device, complete all as specified and directed.

S & F Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm, coloured, with integral foot rests, fixed in repairs including provision of lime concrete bedding complete.Squatting pan including 'P' or 'S' trap & connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and directed.

S&F in repairs PVC valveless dual action flushing cistern of 10 ltrs capacity (white), syphonic action type complete all as specified and directed.

S&F in repairs low level flushing cistern of 10 ltrs capacity PVC valveless, syphonic action type, white with inlet ball valve float and handle complete all as specified.

S&F in repair brass CP health faucet with hand shower and 1.5 mtr flexible stainless steel pipe suitable for fixing to 15 mm dia pipe complete all as specified and directed.

S & F in repair Toilet paper holder of mild steel Chromium plated ‘D’ type, fixed in repairs to walls with chromium plated brass screws complete all as specified and directed.

S & F in repair Vitreous china wash basin with pedestal white, flat back, size 550 x 400mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed.

S&F in repairs elegent mirror PVC cabinet without towel rail of size 422 x 622 mm complete all as specified and directed.

S&F in repairs stainless steel towel rack 60 cm long and 24 cm deep with towel rail and hangers at bottom fixed to walls complete all as specified and directed.

S&F in repairs brass chromium plated shower rose of size 125 mm with arms including fixing to steel pipe complete all as specified and directed.

S&F in repairs 6 mm thik glass corner shelf fancy type with railing and fitting complete of size 25cm x 25 cm of best quality (as per sample approved by Engr -in-charge) complete all as specified and directed.

S&F in repairs wash hand basin mixer 15mm dia CP brass fancy type in lieu of pillar tap including joints to upvc/cpvc pipe or unions . Make : Jaquar cat No :- FLR CHR 5273 UPR , Hindware Cat No :- F570014 CP , Parryware cat No :- G3414A1 complete all as specified and directed.

S & F in repairs Brass CP Wall mixer(Non Telephonic Type) with L bend 3-in-1 for mixing hot & cold water screwed down for upvc/cpvc pipe 15 mm bore in lieu of bib tap and fixed complete all as specified. Jaquar cat No :- FLR CHR 5309N , Hindware Cat No :- F570020 CP , Parryware cat No :- G0316A1

S&F in repairs Kitchen sink mixer 15mm dia CP brass fancy type in lieu of bib tap including joints to upvc/cpvc pipe or unions all as specified. Make : Jaquar cat No :- CON CHR-167KNB , Hindware Cat No :- F570027 CP , Parryware cat No :- G33335A1

S&F in repairs 15 mm bib tap, brass chromium plated fancy type (quarter turn), long body screwed down including necessary extention piece complete all as specified and directed.

S&F in repair 15 mm dia brass chromium plated angle valve fancy type (quarter turn), screwed at ends including necessary extention piece and fixed complete all as specified and directed.

S&F in repairs Good quality Connecton pipe (PVC) complete all as specified.

Demolition of lime concrete in floors (sunken Portion) of any description complete all as specified

M & L 50 mm thick PCC 1:2:4 using 20 mm graded stone aggregate over 250 thick lime concrete type E2 ( 1:3 ) with 40mm brick bats as in filling of sunken floors over a layer of polyethylene film black 50 micron over a layer of bitumen blown any grade applied hot (1.5 Kg/sqm) over 10mm thick plaster in CM 1:3 with WPC @2% by wt. of cement including treatment to side wall of sunken complete all as specified & directed Note:- Over all floor area only be measured for payment, rate for side wall deemed to be included.

Taking down (Door) chowkats or frames with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutter of any description exc 1.00 sqm but n.exc 2.00 sqm each complete all as specified and directed..

Taking down (Door) chowkats or frames with shutter (without taking off the shutter) exc 1.5 Sqm but n.exc 4.00 Sqm each complete all as specified and directed.

S & F Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M & L for Cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in back filling, holdfasts etc, complete all as specified and directed.

S&F 35 mm thick Factory made 2nd class hardwood plain,framed paneled shutters(any numbe of panels) with lock rail and panel of 9mm BWP commercial ply with commercial veneering on both faces size of rail and stile as per IS-1003(part) Kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35 mm thick factory made 2nd class Hard wood glazed and Skelton shutters (any number of panels) open rebated and prepared to receive and including wiremesh/glass/gauge etc with all accessory as required and divided into squares edges of framing Plain, chamfered or rounded mitered and rebated sash bar any number with cut or mitered beads for securing glass/gauge etc Size of members of shutters complete as specified

M & L for preparation of new wooden surfaces of any description not otherwise described over 10 cms width or girth and apply two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame, complete as specified by the manufacturer and as per directions of Engineer-in-charge.

S&F to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge. NOTE : Nos of panels will be decided by Engr-in-charge

Supply and fixing in repairs brass CP hat and coat hooks, solid body, 250mm to 300 mm complete all as specified and directed.

Dismantling wrought iron or mild steel/cast iron work of any description (steel window & Grill) complete all as specified and directed.

S&F fabricated aluminum window with powder coated anodized aluminum frame of section 63.5mm x 38.10mm x1.5mm thick, shutter with section 47.62mm x 44.45mm x 1.5mm thick including aluminum anodized “D “ handle, hinges, peg stays, tower bolts, etc including jointing cleats for fixing builder's hardware fittings & stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples including necessary fittings/ fixture /aluminum snap beads complete all as specified. Note: (a) Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately. (b) Cost of SS wire mesh and all fittings/ fixtures deemed to be incl in the above quoted rates and no extra shall be paid.

M&L powder coated aluminium anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5mm thickness (section no. 20831 of JINDAL) and of shutter size 40 mm x 18 (with 9.00 mm interlocking legs) x 1.45 mm thick (section no. 20737 of JINDAL) section(two shutter glazed, covering half of span of opening each & one shutter sketlon covering half of span of opening ) incl provn for making windows air tight, including 95mm aluminium handle with spring lock , stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4mm and fixed with steel wire stapples and 5mm thick plain glass including necessary fitting/ fixture/ aluminium snap beads complete all as specified. Note: (a) Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately. (b) Cost of glass, SS wire mesh and all fittings/ fixtures deemed to be incl in the above quoted rates and no extra shall be paid.

M & L for Stainless steel (SS) 316 grade any section like tee, angle hollow pipe and square/rectangular tube flat plates etc as in window grill fixed with necessary fittings SS screws, nut, bolts, fastners, washers etc (as approved by Engr-in-charge) including necessary cutting drilling profile, cutting of components to required length/width and shapes/profile and smooth grinding/maching of edges/ faces/all welding joints including buffing and polishing complete all as specified and directed. NOTE : Design/pattern of grill shall be approved by GE.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of perature 1.40mm and fixed with galvanised steel wire staples in door/windows and similar work complete all as specified and directed.

S & F in repair for mild steel, 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

M & L for preparation of old wooden surfaces of any description not otherwise described over 10 cms width or girth and apply one coats of synthetic enamel paint all as specified and directed

M & L for preparation of old Steel surfaces of any description not otherwise described over 10 cms width or girth and apply one coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted Steel surfaces exc 10cm width or girth and applying one coat of aluminium paint of approved shade/tint complete all as specified and directed.

S&F 100mm long (size) butt hinges, stainless steel AISI 304 grade with brass/bronze hinge pin complete all as specified and directed.

S&F stainless steel AISI 304 grade barrel tower bolt 200mm long, extruded section,etc. complete all as specified and directed.

S&F stainless steel AISI 304 grade handle of size 200mm long,etc. complete all as specified and directed.

S&F Stainless steel of AE SI 304 Grade, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F Magic eye and fixed to doors complete all as specified and directed..

S & F Hasp and staple -100 mm size, safety type, aluminium anodised including bolt to hinge plate, fixed with screws complete all as specified and directed.

S & F Floor door stopper (double leg) of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 60mm complete all as specified and directed.

S&F floor door stopper of stainless steel of AE SI 304 Grade body and tongue, with hard drawn steel spring, fixed in floor over all length of cover plate 150mm complete all as specified and directed.

S&F in repair 25 mm dia ss Curtain road with fixing brackets, side knobsof good quality as approved complete all as directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

M & L for Cement concrete 1:3:6 type C1 using 20mm graded stone aggregate in plinth protection, 75mm thick, finished fair and even without using extra cement, complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing complete all as specified and directed. a) 15 mm bore

b) 20 mm bore

c) 25 mm bore

M&L Supplying and laying of UPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittingsBrass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor etc), Unions, Ball valves, Flange and tank adaptor complete all as specified. a) 15 mm bore

b) 20 mm bore

c) 25 mm bore

Dismantling water tanks of capacity exceeding 500 litres but not exceeding 1000 litres complete all as specified and directed.

Dismantling water tanks of capacity exceeding 250 litres but not exceeding 500 litres complete all as specified and directed.

S&F 500 ltr capacity rotational moulded triple layered polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position Including 15 mm brass Flot Valve complete all as specified and directed.

S&F 1000 ltr capacity rotational moulded triple layered polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position Including 25 mm brass float valve complete all as specified and directed.

S & F in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 15 mm bore complete all as specified and directed.

S & F in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25 mm bore complete all as specified and directed.

S & F in repairs Sinks with drainage board made of stainless steel for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, including PVC waste pipe 32 mm bore, 65 cm long complete all as specified and directed.

S & F Sinks without drainage board made of stainless steel for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe, bowl size 460mm x 410mm x 160mm, including PVC waste pipe 32 mm bore, 65 cm long complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drains pipes , jointed in cement morter and taking out of trenches if required up to 100 mm internal dia of drains, complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size, material or pattern) , including all fittings , heads, shoes, bends,swann necks, etc including cleaning or refixing or removal to store complete all as specified.

S&F 110 mm uPVC pipes Type 'B' (for waste water), single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls complete all as specified and directed.

S&F 75 mm uPVC pipes Type 'B' (for waste water), single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls complete all as specified and directed.

S&F 150 mm uPVC pipes Type 'A' (for rain water), single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F 75 mm uPVC pipes Type 'A' (for rain water), single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F 110 mm uPVC (SWR) Bends/ Tees/ Tapers/ cowl (any radius), with or without oval access door as required complete all as specified and directed.

S&F 75 mm uPVC (SWR) Bends/ Tees/ Tapers/ cowl (any radius), with or without oval access door as required complete all as specified and directed.

S&F 150 mm uPVC (SWR) Bends/ Tees/ Tapers (any radius), with or without oval access door as required complete all as specified and directed.

S&F 110 mm uPVC (SWR) branch piece, any length, single (single Y) equal or unequal provided with oval access doors complete all as specified and directed.

S&F 75 mm uPVC (SWR) branch piece, any length, single (single Y) equal or unequal provided with oval access doors complete all as specified and directed.

S&F in repairs uPVC multi floor trap with grating including jointing with solvent cement, dia of outlet complete all as specified and directed.

S & F Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, for any bore and any type of pipes complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc including removal of debrish from the MOD land complete all as specified and directed.

M/L cement plaster 15mm thick in CM 1:6 on brick or conc surfaces finished even and smooth without using extra cement mixed with by adding permeability reducing polymer @ 250gm/sqm (6%) by weight of cementitious content at time of mixing with water as per manufacturer's recommendations including all levelling the surface, curing etc complete all as specified and directed. NOTE : Rates for water proofing compound/ polymer deemed to be included in the above rates.

M &L for providing and applying a bond coat of Latex:Water:cement - 1:4:6 consumption @100gm/sqm on the brick wall surface by brush as per manufacturer's recommendations including curing complete all as specified and directed.

Expose the first joint of masonry structure at ground level horizontally. The plaster must be knocked off at least 50 cm beyond the visibly penetrated area. Damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm. Drilling Holes : Drilling holes 10mm diameter in masonary structure along the side of the joint at 45° angle so as to cross the brick/ block at the intervals spacing of 15-30cm depending on extent of rising dampness as per recommendation of engineer in charge. Cleaning of holes : Clean the holes by air blower prior to fixing nozzles. Install latex polymer packer injection packers 9.8mm diameter, 10cm long in the holes and tighten. Fix the packer securely using sealent. Cutting of Packers : Cut the packers after completion of grouting without damaging structural elements.

Supply and apply of a 3 part, very low viscous, elastic polyacrylic injection resin with a versatile and adjustable reaction time having Mixed viscosity : 3-11 M.pa.s at +20 Deg C, Reaction time : adjustable according to ambient temperatrure and execution requirement between 8-50 mins, pH – 9-10, tested as per Wissbau No. 2002-094-(1A) – Function test with re-injectible hose system. The holes should be drilled until a depth of approx 5 cm (for a 6cm thick wall) before the end of the wall is reached. Pump injcection of polymer resin compound at >20 bar into or behind fissures or into masonry joint which are allowing water to infiltrate into unwanted areas. If voids in masonry being injected contain insufficient moisture to activate the grout inject a small amount of water prior to injecting the grout. When movement stops or polymer compound appears at the packer move to the next packer and inject. If the dampness is heavy, inject similarly at next joint line complete all as specified and directed.

M&L for 15mm thick rendering with ready mix plaster on faces of brick or concrete wall surface, finished even and smooth complete all as specified and directed.

M&L for 10 mm thick rendering with ready mix plaster on ceiling of concrete surface finished even & smooth complete all as specified.

M&L for preparaing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for Preparing new plastered or unplastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over & including a coat of wall care Putty complete all as specified and directed.

M & L for preparing new plastered surface of ceiling and applying three coats of white wash complete all as specified and directed.

Complete removal of existing treatment , wahsing down and stopping of distempered and painted surfaces and old plastered or unplastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over & over a coat of wall care putty complete all as specified and directed.

Complete removal of existing treatment, washing down and stopping painted surfaces and preparing old plastered or unplastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

Complete removal of existing treatment on surfaces of ceiling and applying three coats of distemper oil emulsion complete all as specified and directed.

Cutting holes in brick walls, built in cement mortar or cement lime mortar, exc half brick but not exc one brick, for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required complete all as specified and directed.

M & L for Forming jambs, in CM 1:6 etc., to openings (to foregoing item), including cutting, toothings and properly bonding into old work, including facing and pointing (if necessary) to match existing work, complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

M&L for 18 mm thick wood plastic composites (WPC) board with leaping with same texture, fixed with screws fitted under or above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc complete all as specified and directed. Note : (a) Pattern & design of WPC board to be decided by GE. (b) Items like cupboard knobs, stainless steel channel, CP plate clip hinges to be paid in extra.

S & F CP clip on hinges (Inset) complete all as specified and directed .

S & F 40/50mm dia, cup board knobs fixed with nut, screws and washers of aluminium, anodised complete all as specified and directed.

S&F U shaped double stainless steel channel of size 10 mm x 20mm x 1.50 mm fixed to wooden frame including suitable rail / rollers etc complete all as specified and directed .

S&F 75 mm long (size) butt hinges, stainless steel AISI 304 grade with brass/bronze hinge pin complete all as specified and directed.

M&L for cleaning the sides rolling shutter shafts guide channel and greasing of moving parts of rolling and straightening rolling and replacement of bolts nuts etc as required for smooth functioning of shutters and taking out existing rolling shutters if required and refixing the same in original position complete all as specified (opening of shutter exc 2.00 m and not exc 3.50 m and area exc 6.00 sqm and n.exc 9.00 sqm all as specified)

S& F in repairs mild steel spring conforming to IS 62A-1970 of approved make in existing rolling shutters/opening of shutters exc 2.00 m and n.exc 3.5 m complete all as specified and directed.

S&F in repair steel rolling shutters, thickness of lath 1 mm, with out ball bearing, top cover, anchoring rod and hasp & staple, erected in position where required (in patches or whole), complete push pull or manual type complete as directed

S& F in repair staianless plate rack made of 0.8 mm thick stainless steel sheet of size 750 mm x 900 mm x 210mm consisting of 3 shelf for bowls and one shelf for keeping six nos of big utensil and seven nos of small utensils divided by 10 mm dia stainless steel hollow pipe @ 60 mm centre to centre or as per drg and sample kept in GE"s office complete all as specified and directed.

S & F Continuous (piano) hinges width of flap 30 mm, mild steel, bright finish or electrogalvanised fixed to steel chowkhat with welding or with screws complete all as specified.

S&F in repair bib tap standard of PTMT any color high pressure screwed for iron pipe and fixed to 15mm bore complete all as specified and directed.

S&F in repair stop /angle valve standard of PTMT any color high pressure screwed for iron pipe and fixed to 15mm bore complete all as specified and directed.

Rounding to edges of kota stone slabs on edge, such as in steps, Kitchen slab edgs and other similar situations complete all as specified and directed.

Making holes on kitchen platform, facilitate to insert gas tubing in appropriate size and shape complete all as specified and directed.

Supply and Fixing in repairs, salt glazed stone ware gulley traps 150x150mm size square mouthed type ‘P’ including CI cover complete all as specified and directed

S & F Pressed steel frames of size 105mm x 60mm for doors/cupboard with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

Refixing of shutters of size exc 1.00 sqm but n exc 2 sqm in same or other opening including all necessary adjustments to fit the shutter with frame like easing of shutter for easy closing /opening, tightning of hinges or changing the position of hinges adjustments of tower bolts, Sliding bolts etc complete all as specified and directed.

S&F 15mm mild steel, chromium plated rod with fixing brackets, fixed in cupboards for hanging cloth of adequate strength all as specified and directed.

S&F stainless steel AISI 304 grade handle of size 75 mm long,etc. complete all as specified and directed.

S&F Magnetic catch for wooden cupbord with complete closer macanigum claps and clips fix with stainless steel screw.complete all as specified and as directed.

M&L cement concrete type B2, 1:2:4( 40mm graded aggregate) in foundations, filling and mass concrete complete all as specified and directed.

S&F for roof trusses (framed), trussed, purlins, crane gantries, rails and fsterings and heavy brackets framing (beam, tee, angle, channel or flat sections) confirming to Fe-290, (Gde E-165) including welding etc complete all as specified and directed.

S & F for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding/chajja projections, fixed with self tapping screws complete all as specified and directed.

Cutting chases ,pinning in , making good to facings where required and pointing in cement mortar 1:3 to ends or edges or landings, steps, cills, sunshades,shelves,lintel,etc and cutting in chases for concealed conduit wiring, etc and making good, cutting not exceeding 10 cm girth complete all as specified and directed.

M & L for Mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, welded or forged into spikes, framed guard bars, window frames,column, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screws confirming to Fe.290.Gde-E-165 complete all as specified.

M & L for Preparing new plastered or unplastered surfaces of wall and applying exterior emulsion paint white or tinted over & including a coat of wall care Putty specified for external surface as per manufacturer instruction complete all as specified and directed.

M&L for complete removal of existing treatment on walls by electrical grinder/ sand paper/ steel patti thereafter prepartion of walls by filling of holes and cracks with wall care putty, specified for external surface as required area of surface and applying two coats of exterior emulsion paint (weatherproof /Apex) over a coat of wall care Putty specified for external surface as per manufacturer instruction complete all as specified and directed.

M &L 150 mm thick Hardcore with Broken stone or boulders of gauge n exe 63 mm deposited, spread and levelled in layers, watered and rolled/rammed to a true surface complete all as specified and directed.

M & L 100mm thick Cement concrete type C- 2, 1:3:6 (40mm graded aggregate) as in sub base complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size with pigment confirming to IS 15658-2006 of 60 mm thickness, M-35 grade laid over 50mm sand cushion complete all as specified & directed.

M&L for cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate as in coping including weathering slightly rounded or chamfered angles and throating as directed including necessary formwork complete all as specified and directed.

Surface dressing n exc 15 cm deep complete all as specified and directed

Excavation in post holes in soft/loose soil n.exc 0.5 cum getting out, returing and filling in & raming earth or broken rubble mixed with earth around, in layers n.exc 25CM, watering and removing surplus soil to a distance n.exc 50m and making good surface complete all as specified and directed.

M&L cement concrete 1:3:6 type C2 (40mm graded stone aggregate) in foundation filling and mass concrete complete all as specified and directed.

M&L 10mm dia round bar and over, cut to length, bent to shape required, including cranking, bending spirally for hooping c complete all as specified and directed.

Mild steel Screw bolts (machine made) with hexagonal or square heads at one end and scewed the other, each screwed end to be fixed with one washer and one hexagonal nut, the other end to be embedded in RCC fencing post while casting for fixing chain link fencing, dia of bolt neck 11 to 15 mm and length of bolt exc 5cm but n exc 10cm long, complete all as specified and as directed.

Supply only Chain link MS galvanised fencing, any size or type complete all as specified and directed.

Fixing only chain link fencing including line wire, any mesh, size and type to any type of standards, rails, straining bolts, etc including provission of binding wire. Complete all as specified and directed.

S&F mild steel work such as in fencing post, tie bars, angle, tee, flat etc including embedding into concrete and making holes for screwing of nut, bolts, cutting top to shape as directed, drilling holes, notching for wire etc confirming Fe 410-0 or Fe 310-0 all as specified and directed.

M&L cement concrete 1:3:6 type C2 (40mm graded stone aggregate) in foundation filling and mass concrete complete all as specified and directed.

M&L for 2 coats of synthetic enamel paint over a coat of red oxide on steel surfaces exc 10 cm width or girth etc complete all as specified and directed.

Description of Work / Item(s)

Amount

Taking down carefully aluminium point wiring (light/fan/bell/socket /power) with complete fittings such as old conduit, steel terminal boxes, switches, ceiling roses, pendents, regulators, sockets etc and removing the material including making good the distrubed surfaces of the wall flooring ceiling etc to match the existing surface complete all as specified and directed

M&L for concealed point wiring complete with stranded copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable drawn through concealed PVC conduit and including replacement of unserviceable pressed steel terminal boxes with Modular steel terminal boxes factory made including white cover modular plate with frame suitable for modular switches, modular sockets, modular fan regulators etc of required size complete including 1.5 sqmm copper cable earth continuity wire to common earth and connected to earth dolly complete all as specified and directed for One light/Fan/Bell point controlled by one 5 Amp switch one way using cable (1.5 Sq mm for phase and neutral and 1.5 sqmm for earthing) complete all as specified and directed . Note :- The rate is inclusive cutting/chasing and making good disturbed surface with CM 1:3 and same surface finishs with the adjoining surface of disturbed area with OBD/Colour wash/white wash complete.

All as per item No 2 here-in-before but 5 Amp socket outlet on same board.

All as per item No 2 here-in-before but 3 Pin Socket outlet 5 Amps on independent board with cables 2.5 Sqmm size for phase and neutral and 2.5 sqmm for earthing

All as Item No 2 here-in-before but for one socket outlet 5/15 Amps on Independent board with cables 2.5 sqmm size for phase and neutral and 2.5 Sqmm for earthing

All as Item No. 2 here-in-before but for one light point controlled by two 2-way switches with cable 1.5 Sqmm size.

M&L for concealed point wiring complete with stranded copper conductor 4 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable drawn through concealed PVC conduit complete including 4 sqmm copper cable earth continuity wire to common earth and connected to earth dolly complete all as specified for one socket outlet for modular AC Box on Independent board with cables 4.0 sqmm size for phase and neutral and 4 Sqmm for earthing complete all as specified and directed Note:- the rate is inclusive cutting /chasing and making good the disturbed surface with cm 1:3 and same surface finishes with the adjoining surface of disturbed area with OBD/colour wash/white wash complete

S&F switch modular type, 1 way 6A, 1module complete all as specified and directed

S&F switch , Modular switch 2 way 6A, 1 module complete all as specified and directed

S&F Modular Socket, 6A - 2/3 pin 2module complete all as specified and directed

S&F switch modular type 1way 16A, 1module complete all as specified and directed

S&F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed

S&F Modular Bell push 6A 1 module complete all as specified and directed

S & F in replacement ,Decorative wall light mounting suitable for LED Lamp upto 15 Watt with all connections complete all as specified and directed

Supply and fixing in replacement surface mounted round shaped LED downlight with durable housing with Al heat shrink with diffuser to give glare free light 12 watt LED 6000K/6500K lamp type from ceiling of stairs/common areas, complete all as specified and directed . Make : Bajaj Cat Part No-BGSLO12W6000K / Wipro Cat Part No-WP1076 / Crompton Cat Part No – LCDSPLN-R-12-CDL

S&F in replacement Wall mounted LED Integrated Batten 20 Watt - 4Ft White, indoor decorative LED battern complete all as specified and directed (Make Bajaj Cat Part No-BCLAB 20W WH LED P/ Crompton Cat Part No- LDL-20-CDL / Wipro Cat Part No-LL20-281-XXX-65AL1)

S&F in replacement Wall mounted LED Integrated Batten 10 Watt-2 Ft White, indoor decorative LED batten, complete all as specified and directed .(Make: Make- Bajaj Cat Part No-BCLSB10 WH / Crompton Cat Part No-LCTLN-10-CDL / Havells Cat Part No-ENDURALINEARNEOBS10WLED865SPCWH.)

S&F Modular AC Box with socket and MCB SP 25 Amp complete with Metal box , white colour plate and frame complete in replacement of sheet metal enclosures as per site requirement , complete all as specified and directed.

S&F Earth Leakage Circuit Breaker 16A, 30 mA, 1P+N C16 ELCB Complete with Sheet Metal Enclosure Distribution Board for geyser complete all as specified and directed

S&F of lamp holder Angle/ Batten type bakelite insulated body with back plate complete all as specified and directed

S&F LED lamp 12 Watt LED Bulb complete all as specified and directed.

S&F of electric bell Ding Dong type AC, 230 volts single phase complete all as specified and directed

S&F ceiling rose surface Bakelite 65x25mm two to three terminals complete all as specified and directed .

S&F in replacement LED bulk head in engineering plastic housing with clear prismatic diffuser, 10W WHITE in replacement of old unsv bulk head fitting including all accessories connecting up twin core flexible copper conductor cable complete all as specified and directed . Make: Make- Havells Cat Part No - HEXAFT10WLED857SSYMBOPC / Crompton Cat Part No- LBHE-10-CDL / Wipro Cat Part No- WP1099.

S&F in replacement of building security light fitting 30W LED 5000K new Powder coated LED Street light including fabrication of GI bracket of suitable dia for fixing of Led light fitting duly fixed with clamps, nut, bolts, & washers etc complete all as specified and directed . Make - Crompton Cat Part No-LSTS-30-CDL-M / Havells Cat part No-ENDURAPEARLSL30WLED757SASYTOPCMP / Bajaj Cat Part No – BCLST30W LED

S&F for stepped type electronic fan regulator modular type, 2 module complete all as specified and directed

S&F BLDC (Brushless Direct Current) Ceiling Fan 1200 mm Sweep operated through regulator not less than 350 RPMhaving air delivery 215Cum, high air flow with silence operation, with fully copper winded motor & ribbed 3 Nos A/M blades. The BLDC motor fan shall have 100% rust free blades. The fan shall be BEE 5 Star rating and compliant with IS 374 and making necessary electric connection of suitable PVC copper wire from ceiling rose to ceiling fan including taking down old ceiling fan and depositing to MES store yard complete all as specified and directed. Make :- Orient -Hector/Havells-Efficiencia Neo/Bajaj-Energos 28

S&F Exhaust Fan, heavy duty Metal body, copper wound 300 mm Sweep, 1400RPM with metal louvers including taking down of old exhasut fan and depositing to MES store yard and connecting up complete all as specified and directed

S&F Hot Water Storage (Geyser) 25 Ltrs Capacity, BEE 5 Star Rated, metal body glass link tank including taking down of old geyser of 50 Ltr capacity (40 Nos)and depositing to MES store yard and connecting up the geyser with replacement of plug top 16 Amps 30mA PRCD plug top (white) complete all as specified and directed

S&F in replacement of VTPN DB 4 way double door, vertical type for fixing MCCB 4 pole up to 250 Amps as incommer and MCBs as out goings with metel door and IP 43 Protections and connecting complete all as of approved make by the GE.

S&F in replacement of sheet metal enclosures double door for DBs when MCBs to be used SPN-12 Way, 240V complete as per site requirement complete all as specified and directed .

S&F in replacement of sheet metal enclosures double door for DBs when MCBs to be used SPN-8 Way, 240V complete as per site requirement complete all as specified and directed .

S&F in replacement of MCCB 4 Pole .415 V. fixed type, 160 Amps with breaking capacity 36kA complete all as specified and directed

S&F in replacement MCB SPN 63 Amps 'C' series, breaking capacity 10 Ka, 'C' curve 240 volts, 50 Hz including necessary incoming and out going electric connection with suitable size of copper lugs etc complete all as specified and directed

S&F in replacement MCB SPN 40 Amps 'C' series, breaking capacity 10 Ka, 'C' curve 240 volts, 50 Hz including necessary incoming and out going electric connection with suitable size of copper lugs etc. complete all as specified and directed

S&F for MCB SP 63 Amps 240 Volts, 10kA, `C' curve all as per site requirement complete all as specified and directed

S&F for MCB SP 6 to 32 Amps 240 Volts, 10kA, `C' curve all as per site requirement complete all as specified and directed

M&L for earthing with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 M below normal ground level connected to GI wire 4 mm as earthing lead by means of nut, bolts and check nuts and washers, GI light grade protection pipe 15 mm dia upto 7.5 M, GI watering pipe 20 mm dia medium grade, RCC cover with funnel, excavation in any type of soil, PCC pit charcoal, salt all as shown in electrical plate No 5 of SSR Part I, including earth test point upto panel board, or indicated including testing on completion complete all as specified and directed

S&F in replacement Sheet metal enclosure of size 300 x 250 x 150 mm suitable for mounting Pre paid meter fabricated from CRCA sheet with anti corrosive dust and vermin proof. Note:- The meter cover shall have a transparent window. The window shall be of transparent, high grade UV stabilized engineering plastic for easy reading of all the displayed values/parameters and observation of operation indicator. The window shall preferably be an integral part of meter cover complete all as specified and directed

Taking down and refixing Prepaid meter and Monitoring device with consultation with prepaid meter authorities including passing existing 3 pair cable from prepaid meter to monitoring device through PVC concealed conduit and necessary connections and testing on completion of work complete all as specified and directed Note - The rates are inclusive of Cutting / chasing and making good to disturbed surface with CM 1: 3 and same surface finishes with the adjoining surface of disturbed area with OBD / Colour wash /white wash complete.

Taking down unserviceable sub main wiring twin core of any size complete and making good disturbed surface complete all as specified and directed.

M&L for Sub Main wiring using single run PVC FRLS grade Insulated unsheathed, multistrand copper conductor cable 2 runs of 10 Sqmm for phase and neutral and 1 run of 10 Sqmm for earth wire drawn through concealed PVC conduit wiring in wall not less than 25mm dia with all fittings like tees, bends, junction/ terminal boxes etc as per site requirement complete all as specified and directed . (Note:- Phase should be of Red /Yellow/Blue, neutral should be of back and earthing wire should be of green colour. 2 runs of cable for phase/ neutral and 1 run for earth will be measured and paid as one unit length).

ASSOCIATED CONSTRUCTION CO.

AMIT ASSOCIATES

Third Wave Services Pvt Ltd

M/s Arihant Builders

GOYALA INFRA PROJECTS PVT LTD.

City Promoter and Buildwell Pvt. Ltd.

AMIT ASSOCIATES

M/s Arihant Builders

India Guniting Corporation

Third Wave Services Pvt Ltd

GOYALA INFRA PROJECTS PVT LTD.

City Promoter and Buildwell Pvt. Ltd.

Bidder Name

AMIT ASSOCIATES

Third Wave Services Pvt Ltd

City Promoter and Buildwell Pvt. Ltd.

GOYALA INFRA PROJECTS PVT LTD.

M/s Arihant Builders

India Guniting Corporation

ASSOCIATED CONSTRUCTION CO.