Repair to hard standing fencing joinery rolling shutters collapsible gates and railing in NAD Jetty NCB and 2W Det under AGE B R I in GE Gomantak Vasco

Amount

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) and disposing off the rubbish outside MD land complete all as specified and directed.

M&L 40mm thick cement concrete type, B1 (1:2:4) using (20 mm graded aggregate) as in sub base of floor all as specified and as directed.

M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick,set, jointed and pointed in neatcement slurry in floors with Grey cement and pigment over 15mm thick screed in CM (1:4) all as specified and directed .

M&L for heavy duty parking floor tiles 30cm x 30cm x 10mm thick,set, jointed and pointed in neatcement slurry in floors with Grey cement and pigment over 15mm thick screed in CM (1:4) all as specified and directed .

M & L for 75 mm thick PCC (1:4:8) type D-2 (using 40mm graded aggregate), as in sub base floorall as specified and as directed.

M & L for 50 mm thick Sand filling under floor, for cushinoning of interlocking tiles including watering and consolidation as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, with grey cement and pigment.

Dismantling fencing wire mesh any type and any size

Dismantling RCC fencing posts or struts any section, including taking out embedded portion and making good disturbed natural ground, (RCC fencing posts)

Excavating in trench n.exc 1.50m deep, getting out, in soft/ disintegrated rock all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers non.exc 25cm all as specified and directed.

Removing excavated material exc. 250 m but n.exc. 500 m and depositing where directed all as specified and directed.

M & L Cement concrete 1:3:6 type C1 using 40mm graded aggregate as in post hole, foundaitons, filling and mass concrete all as specified and directed.

M&L for precast cement concrete (1:2:4) type B1 using 20mm graded aggregate in columns, Fencing posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc (of any section indicated) with plain fair faces, including chamfers weatherings, throating etc, and setting in mortar (1:4) complete with joints to match all as specified and directed.

M&L Mild steel bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping forcolumns, hooking ends and binding withmild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to TMT bars.

Ditto but 5mm dia and over upto and incl 10mm dia in strirups, spacer and binder, all as specified and directed.

M&L Mild steel bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping forcolumns, hooking ends and binding withmild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Round bars all as specified and directed.

S & F mild steel work like angle iron, flat iron etc in posts and struts in fencing incl cutting tops to shape as directed, drilling holes, notching for wire etc including all necessary drilling conforming to Fe 290 Gde E-165 all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm and n exc 10cm long and 12mm dia

Supply and fixing PVC coated MS galvanised chain link fencing of size 75 x 75mm of any type of standard rail straining bolts etc including provision of binding wire.

S&F barbed wire fencing with galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixed to any type of standard rails or straining bolts including securing or tying at crossing with and provn of galvanised mild steel wire all as directed (Each line wire to be measured)

Taking down chowkats with shutters (without taking off shutters from the frames) area n exc 1.5 Sqm all as specified & directed.

Taking down chowkats with shutters (without taking off shutters from the frames) area exc 1.5 Sqm and n. exc 4.00 Sqm each all as specified & directed.

Taking down shutters only area exc 1.0 Sqm and n. exc 2.00 Sqm each all as specified & directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube complete all as specified.

S&F solid PVC moulded door shutted with particle board core, 28 to 30mm thick (stiles) with 2 raised panels designed with 2mm thick moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face complete all as specified.

M&L for 2nd Class HW Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with gluepinned at joints, supplied and fixed.

S&F for 35 mm thick 2nd class hardwood glazed shutters open rebated and prepared to recive glass/gauge but divided into squares with plain, chamfered or round, mitred any rebated sash bar, any numbers complete all as specified and as directed..

S&F for 35 mm thick 2nd class hardwood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides, (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats .

M&L.preparing surfaces of wood and wood based materials,steel and iron work,new or old ,of any description and girth ,not otherwise described,and treated with tar or coal tar black paint all as specified and as directed..

Cutting holes in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3, exc half brick but n exc one brick ( Depth of embedded portion of hold fasts or lugs measured from the face of the jamb into the wall) all as specified and as directed.

S & F MS Flat bands, straps, supports or stays & hold fasts and similar small articles confirming to grade Fe – 290 Gde E 165. all as specified and as directed.

M & L treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc., area n exc 0.1 sq. m each, ditto all as specified and as directed.

M & L painting small articles such as rafter feet, brackets or cantilevers n exc 30 cm projection and locks, labels, etc. n exc 0.1 sq. m each all as specified and as directed.

M&L. sanding newly tarred or painted surfaces with clean sharp sand all as specified and as directed..

S&F butt hinge 100mm long stainless steel as directed by Engr-in-Charge

S&F 150mm long aluminium alloy handle fabricated type anodised

S&F150 mm long aluminium anodised barrel tower bolt of extruded section

S&F 300 mm long, aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section fixing bolts and sliding bolt of extruded section or cast aluminium alloy.

S&F framed work as in doors or gates of angle or other section with gueest plates, rails, braces, etc. complete, drilled for fixing of steel sheeting or other covering, Doors etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (Exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete FE-410W (Gde-E250) Quality B as directed by Engr-in-Charge.

S&F for mild steel plain sheet 1.25mm thick covering to door shutters, covering to door chowkats (frames) etc cut to size, edges beaded if directed, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel members, etc, with plain 40mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc as required as directed by Engr-in-Charge.

S & F powder coated window or ventilator shutter and frame any type (slidding or openable) with frame or other similar work etc 80 micron section fabricated by using the JINDAL/INDAL/HINDALCO/sections including necessary roller,wheel cleat handles, locking arrangements to receive 4mm thick glass for wire net with aluminum chanel beading and stainless steel screws including cost of rubber gasket beading etc complete (the weight of rubber gasket beading will not be measured with the weight of aluminum shuter glass will be measured and paid separately) scections as approved by GE

S&F for 9mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to aluminium frame work as directed by Engr-in-Charge.

S & F sheet glass 4mm thick ordinary quality and glazing with clips exc 0.5 sqm in each pane all as specified and as directed.

S& F aluminium wire mesh of size 1.5mm x 3mm x mesh 2.0mm thick of make M/s Kiran Nettting, all as sprcified and directed.

S&F in repair aluminium wire mesh of size 1.5mm x 3mm mesh 2.0mm thick of make M/s Kiran Netting. Incl necessary woodrn or aluminium beading etc all as specified and as directed.

S & F power coated aluminium daco grill (DG 104) fixing with F section chanel complete all as specified and using power coated section of minium powder coating 50 microns. all as specified and as directed.

Taking down rolling shutters of any size including top cover, guide channel etc. all as specified & directed.

S&F steel rolling shutters, with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated complete push pull or manual type thickness of lathe 1.25mm incl taking down old rolling shutter as directed by Engr-in-Charge.

S&F steel rolling shutters, with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated complete but gear operated type with bevel gear box and crank handle thickness of lathe 1.25mm incl taking down old rolling shutter.

M&L for repairing / servicing of rolling shutter area not exceeding 15.0Sqm incl replacement of necessary component all as specified and as directed by Engr-in-Charge.

S&F in repair stainless steel railing with 25, 40, 50 mm dia pipe alongwith necessary fittings conforming to Grade - 304 etc., erected in position and securing runners with holdfasts and brackets, complete as specified and directed by Engr-in-Charge.

S & F mild steel work Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for ddors, balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting or riveting etc, and similar work conforming to FE-290 Gde E-165.

M&L for Two coats of synthetic enamel paint over one coat of primer including preparation of. new steel surfaces n exc 10cm width or girth all as spcified and as directed.

M&L for two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description over 10 cm in width or girth not otherwise described including preparation of surfaces.

M&L preparation of surfaces and applying two coat of aluminium paint on new steel surface of any description not otherwise, described over 10cm width or girth over a coat of aluminium red oxide for rolling shutter all as specificed and as directed.

M & L applying two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described over 10cm width or girth including preparation of new surface & applying one coat of red oxide, zinc chrome all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and 15 mm thick cement plaster on External fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement .all as specified & directed.

M&L for three coats of white wash on wall surfaces including preparation of newly plastered surfaces all as specified and as directed.

M & L for two coats of oil bound distemper over a coat of primer including preparation of newly plastered surfaces of walls complete all as per manufactures instructions.

Removing building material / debris to a distance of exceeding 500m not per load exceeding 1.0 km and spreading in layers all as specified and as directed.

M/S jvsr constructions

M/S P S BABU