REPAIR TO RETAINING WALL FOOTPATH FENCING GATE AND COMPOUND WALL WITH DRAIN UNDER AGE BR I AT BB CANTT SRINAGAR

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling fencing wire mesh, any type complete all as specified and directed.

M&L for PCC (1:2:4), Type B-2 (using 40mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for mild steel work as in nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and as directed. Note : Actual weight of the fencing shall be ascertained by Board of Officers to be convened by GE.

Fixing only chain link fencing including line wires, any mesh size and type to any type of standard rails, straining bolts etc, including provision of binding wire, complete all as specified and directed.

S&F Mild steel bolts purpose made with hexagonal or square head one end other end screwed the other exc 12mm and n.exc 20mm dia, length of bolt n.exc 30 cm long conforming to relevent IS complete all as specified and directed.

S&F in repair galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolt, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins complete all as specified and directed. (Each line wire to be measured)

M&L for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for Mild steel round bars Gd.I, IS- 432 (Part I) Part- I, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

Demolition of RCC (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified and directed.

M&L for brick work with old size sub class 'B' bricks straight or curved on plan exc 6m mean radius and built in CM 1:6 complete all as specified and directed.

Demolition of plain cement concrete (un-reinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level) etc complete all as specified and directed.

M&L for 75mm thick PCC (1:4:8), Type D-2 (using 40mm graded crushed stone aggregates) as in sub base/levelling course of floors etc complete all as specified and as directed.

M&L for 25mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in sub baseof floor finished even and rough to receive floor finishes complete all as specified.

M&L for colured chequered cement concrete tiles 25cmx25cmx22mm thick, set jointed and pointed in neat cement slurry with grey cement and pigment over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for coloured exterior wall cladding designer tiles on vertical surface of size 300mmx600mmx7-8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles, fixed over and including 15mm thick backing coat in CM 1:4 on any type of wall complete all as specified and directed.

M & L for rendering 15mm thick in CM (1:4), mixed with and including water proofing compound as per manufactureer's instructions, on fair faces of brick work or concrete surfaces finished even and fair complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in cills, roof kerb, seismic and other similar bands, copings, kneelers, apex stones, bed plates, bond stones and the like including weathering slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

M&L for precast RCC (nominal mix) 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles including necessary formwork complete all as specified and directed.

S&F for Framed work such as angle iron frames for man hole, covers, grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290 Gde-E-165 complete all as specified and directed.

S&F Parliament hinges, mild steel cold rolled, width of recess between flanges (when open) 150mm complete all as specified and directed.

S&F rolled mild steel plates (plain or chequrred) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment of grade FE-410W (Gde E 250 quality A ) complete all as specified and as directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for walling of random rubble stone masonry uncoursed, well bonded, bedded and solidly hearted built in CM 1:4 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses, hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc. 40mm of lime or sand stone complete all as specified and directed.

M&L for raised pointing to random or polygonal rubble uncoursed or brought upto course stone masonry in CM (1:3) complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls etc as in weep holes complete all as specified and directed.

M&L for 100mm thick PCC 1:2:4 type B-2 (using 40mm graded crushed stone aggregate) as in sub base/ flooring/hard standing complete all as specified.

Forming Construction joints 30mm deep x 10mm wide, filled with sealing compound Grade 'A' complete all as specified and directed.

S&F 2mm thick fiber glass reinforced translucent corrugated sheeting with two corrugations side lamp fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting any gauge thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and directed.

M/S Ghulam Mohammad Shalla

M/S BASHIR AND SONS

M/S AIJAZ ENTERPRISES

AHMED CONSTRUCTIONS AND INFRA PVT LTD