SPL REPAIR TO CAPT LT OFFRS MD ACCN BLDG NO PO 155 01 AND 02 AT SOMNATH ENCLAVE IN SUKNA MIL STN AND CERTAIN OTHER SANCTIONED WORKS IN SUKNA MIL STN UNDER GE SUKNA

Amount

Excavation over areas not exceeding 1.5 M deep and getting out in Soft/ Loose Soil complete all as specified and directed.

Excavation over areas for each additional 1.5 m or part there of in depth beyond the first 1.5 m complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and directed.

Removing Excavated material soils exc. 250 M and depositing where directed at a level not exc. 500 M above the starting point complete all as specified and directed.

M&L loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells using broken bricks complete all as specified and directed.

M&L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M & L for Plain Cement Concrete Type B0 1:2:4 (using 12.5 mm graded stone aggregate) in top of chajja , roof kerbs or mud stops, rounded or chamfered on edges etc complete all as specified and as directed.

M&L PCC 1:2:4 type C-1 (using 12.5 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks in one brick thick honey-comb wall built in cement mortar 1:6 complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

M&L for rendering 15 mm thick on other then fair faces of brick work or concrete surfaces in cement mortar 1:6 finished the surface even and smooth without using extra cement complete all as specified and directed.

M & L for PCC 1:3:6 type D2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore pipe complete all as specified and directed.

M & L 150 mm dia Salt Glazed stone ware drain pipes laid in trenches and jointed in CM 1:1 complete all as specified and directed.

M&L preparation of new steel surfaces of any description not exceeding 10 cm width or girth when unconnected with other painting or when painted in a different tint and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for Plain Cement Concrete Type E2 1:5:10 (using 40 mm graded stone aggregate) as in sunken floor, foundations, filling and mass concrete complete all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, similar bands, plinth coarses, string coarses, lacing coarces, parapets nad railings upto 60 cm in height, filling in pressed steel door frames, wall of drains, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L for Precast cement concrete 1:2:4, type B1 (Using 20 mm graded stone aggregate) in landings, cover slabs (for Manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 and including demolition complete all as specified and directed.

Demolition of existing WC floor including PCC/ tile flooring, traps attached to WC , lean concrete ,plaster and removing all debrises off the site complete all as specified nad directed.

M&L for Reinforced Cement Concrete Type B-1 1:2:4 (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed.

Supply only integral water proofing compound complete all as specified.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

S&F Polythene film, 150 micron thick, laid over and including on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq.m complete all specified and directed.

M& L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting n.exc. 10 cm in girth complete all as specified and directed.

M&L 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like laid over and including screed bed 15 mm thick in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and complete all as specified and directed.

M&L for rough finished flat formwork to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc. 200 mm thick (horizontal or sloping) work as rough finished surfaces of concrete complete all as specified and directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement complete all as specified and directed.

S & F 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. size of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkhats complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with block board core and plywood face fanels, commercial type on both side with liping/frame to match complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with MDF board exterior grade, commercial type on both side and covered on both side with decorative face veneer with liping/frame to match complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

S&F in repairs PVC cabinet of size not less than 445 x 380 x 95 mm for bathroom, made out of 2mm thick acrylic sheet with internal shelves and openable shutters including 10 mm dia aluminium / brass CP rod complete all as specified and directed.

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

M&L Stainless steel fancy handle of size 100 mm long Chromium plated complete all as specified and directed.

S&F 100 mm mild steel butt hinge, medium weight, bright polished complete all as specified and directed.

S&F 30 mm continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S & F 300 mm long ordinary rat tail pattern springs including roller and roller plate complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F Hasp and staple 150 mm safety type brass with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and as directed.

S&F in repair Stainless steel towel rail 600mm, 20mm dia, D type of brass chromium plated fixed with and including CP brass screws complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F stainless steel telescopic channels power coated with ball bearing min 60 cm long standard width fixed over and including 2 nd class hard wood fillet section area exc 3 sqcm and n.exc 6 sqcm clean swan secured with screws complete all as specified and directed.

S&F in repair Stainless steel kitchen rack made out of stainless steel sheet 1mm thick with approx size 900mmx900mmx250mm best quality complete all as specified and directed.

S&F in repair curtain rod, mild steel, chromium plated with (fancy type) for doors/window opening complete all as specified and directed.

S&F Decorative type wooden finish single type brackets side brackets support for holding mild steel, chromium plated finish curtain rods and corner to be fixed to ends of curtain rod fixing with screws complete all as specified and directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for Mild TMT bars 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S&F Mild steel screw bolts diameter of neck 16 to 20 mm (machine made) with hexoganal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut, exc. 22.5 cm but not exc. 30 cm long complete all as specified and directed.

M&L welded steel wire fabric square mesh supplied and fixed complete to wood or steel members, weight not exc. 4 kg per square metre complete all as specified and directed.

M&L rolled mild steel conforming to Fe 290 (Gde E-165), in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) and including distance pieces, cleats etc. confirming to Fe – 410 – W(Gde E - 250) quality 'A' complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dove-tailed or welded complete all as specified and directed.

S&F Steel ventilator with top hung shutter and including hinges steel peg stay complete all as specified and directed.

S & F of pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

S & F of pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

S&F aluminium powder coated frame work (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws complete as per architectural drawings and the directions of Engineer-in-charge.

S&F aluminium powder coated frame work (minimum thickness of powder coating 50 micron) for shutter of doors, windows, ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (fittings shall be paid for separately) with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws complete as per architectural drawings and the directions of Engineer-in-charge.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F in repairs 18/19 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination and other side balancing white laminated kitchen CB drawer, cup boards cabinates etc fixed with screw to timber / aluminium frame work complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2, (using 20 mm graded crushed stone aggregate) as in plinth protection, hardstanding, floors, paths, etc, finished even and smooth without using extra cement including spike rolling to making impression of expended metal, whilst the concrete complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in sunken portion including demolition of old concrete complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 20 mm thick screed bed in CM 1:6 finish even and rough complete all as specified and directed.

M&L Coloured glazed ceramic tiles 350x 250x 7 mm/ 450X 350X 7mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 cm thick backing with cm 1:3 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 and dismantling complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement using WPC compound complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M/L 10 mm thick cement plaster in CM (1:3) using WPC @ 3% by wt of cement in sunken portion complete all as specified and directed. (Note:- WPC will be measured and paid separately)

M&L for rendering 5 mm thick in CM 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for cleaning the surfaces of sunken floor using wire brush , brooming down and washing down with water to remove dust etc. and brushing with neat cement slurry @0.5 kg/sqm with acrylic based polymer modified cementious composite (Pidifine 2K) @ 0.50 kg/sqm complete all as specified and directed.

M&L preparation of new plastered ceiling surfaces and including applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty complete all as specified and directed.

M&L Complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M&L Complete removal of existing treatment of old decorated wall surfaces and including applying two coats of weather coat (Apex paint) over one coat of primer complete all as specified and directed.

M&L Finishing walls with Acrylic smooth exterior paint of required shade New work two or more coat applied @ 1.67 ltr / 10 sqmm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqmm complete all as specified and directed.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

S&F 4.8 mm thick glass including tinted/dark film not exc. 0.5 sqm each pane complete fixed to aluminium frame work including rubber beading complete all as specified and directed.

S&F 4.8 mm thick glass including tinted/dark film exc. 0.5 sqm each pane complete fixed to aluminium frame work including rubber beading complete all as specified and directed.

S&F for in repairs Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F in repairs Glass corner shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated brackets guards and railing 60 cm long complete all as specified and directed.

M&L preparation of old decorated steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Taking down 15 mm bore steel water tubing and connections from wall / ceiling including cleaning for refixing or removing from site of work complete all as specified and directed.

Taking down 20 mm bore steel water tubing and connections from wall / ceiling including cleaning for refixing or removing from site of work complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc.) and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc.) and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank including dismantling of old tank complete all as specified and directed.

S&F in repairs 15 mm bore bib tap chromium plated long body fancy type, cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F 15 mm bore bib tap, cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F in repairs, Wall mixer non telephonic complete all as specified and directed. Make :- Jaquar.

S&F in repair 3 hole basin mixer with out popup waste system, brass, chromium plated, for mixing hot and cold water, with 450 mm Long Braided Hoses, screwed down for 15 mm bore pipe complete all as specified and directed. Make :- Jaquar.

S&F in repairs angle stop cock 15 mm bore, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or unions and fixed, fancy type, chromium plated long thread with flange complete all as specified and directed.

S & F in repairs 15 mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S & F in repairs Fancy type chromium plated with long shank and cup (Concealed type) 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F in repairs CP Grating doom 100 mm dia with waste hole of PTMT. (Minimum weight 25gms) complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts, of length 450 mm & suitable for cold/hot water supply complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius, fixed with cement solvent, with oval access door complete all as specified and directed.

S & F 110 mm bore PVC (SWR) branch piece single, (single Y) equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) junction double, (double T) equal or unequal, fixed with cement solvent, complete all as specified and directed.

S&F in replacement sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 x 460mm bowl size 405 x 355 x 178 mm and including 32 mm waste pipe & coupling complete all as specified and directed.

S&F in repairs vitreous china european water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S&F in repairs vitreous china wash hand basin white flat back of size not less than 550 x 400 mm with and including PVC waste pipe 32 mm bore, CP waste fitting and cutting for and pinning in ends of brackets etc, complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair swivel shower rose size 125 mm of brass chromium plated any colour (minimum weight 40 gms) for fixing with 15mm dia steel pipe complete all as specified and directed.

S & F in repairs soap dish, with metal dish brass chromium plated fixed to plugs complete all as specified and directed.

S&F in repairs Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed.

S&F in repairs health faucet 12 mm bore, ABS chromium plated with & including 1.0 mtr chromium plated flexible tube & wall hook and connection with angular stop cock complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Taking down eaves gutters PVC rainwater pipes complete all as specified and directed.

M&L for roof treatment in order of precedence as given below complete all as specified and as directed:- (i) Taking out of existing water proofing treatment and including padding, cleaning the surface using wire brush, brooming down and washing down with water to remove dust etc, and brushing with neat cement slurry @ 3.00 kg of cement per Sqm. (ii) 15 mm thick screed bed in CM 1:4 on surface. (iii) Cleaning of plastered surface and applying one coat of bituminous primer @ 0.40 Ltr / Sqm. (Contd...)

(iv) Supply and laying 3 mm (Minimum) thick APP based polymeric membrane of approved manufacturer with weight not less than 3.60 Kg per Sqm, reinforced with non-woven polyester fabric weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a height of 30 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (v) Applying two coat of water proofing aluminium paint with aluminium finish over APP as per manufacturer's instruction. Note :- (a) Bituminous primer shall be "ShaliTex Primer" manufactured by M/s STP Ltd or equivalent in M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (b) Laying APP based polymeric membrane shall be done by torch on method as per manufactures instructions. (c) A minimum overlap of 100 mm and 75 mm should be made at the end and sides of the polymeric membrane respectively and all overlaps and joints shall be sealed as per manufacturers instruction. (d) APP based polymeric membrane shall be manufactured by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (e) Water proofing paint shall be by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited

Taking down copper / aluminium concealed point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc., removing materials to store for keeping in safe custody or for taking credit, cutting chasing as required and making good the disturbed surfaces including finishes to match with adjacent surfaces of walls, floors, etc. complete all as specified and as directed.

Taking down old unseviceable DB/TPN DB any size and any capacity including MCB/RCB/Isolator complete all as specified and as directed.

Taking down carefully damaged sub main wiring of size up to 10 sqmm including making good disturbed surfaces of walls, ceilings etccomplete all as specified and as directed.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including PVC casing caping (double lock pattern) and accessories on wall / ceiling surfaces etc. with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc including all other fixing accessories for one light / fan / exhaust fan point controlled by one 5 / 6 Amps switch wiring & connected switch / socket / regulator bell etc. complete all as specified and directed.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, modular plate and frame on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch, all necessary cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed.

All as per Sl. item No. 132.00 above but for one 5 / 6 Amps socket outlet point on independent board.

All as per Sl. item No. 132.00 above but for one 16 Amps socket outlet point on independent board with 2.5 sqmm cable and 2.5 sqmm earth wire

All as per Sl. item No. 132.00 above but for one 5 / 6 Amps socket outlet point on same board.

M & L for sub main wiring with 2 runs of 2.5 sqmm main wire alongwith 1 run of 2.5 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade copper conductor cable, drawn through and including adequate size PVC casing caping (double lock pattern) with all fittings & accessories on walls / ceiling surfaces etc., complete all as specified and directed. NOTE :- Two runs of main copper conductor, one run of earth wire and one run of PVC casing caping shall be measured as one unit length.

All as per item No.136 above but with 2 runs of 4.0 Sqmm main wire along with 1 run of 4.0 Sqmm earth wire.

All as per item No.136 above but with 2 runs of 6.0 Sqmm main wire along with 1 run of 6.0 Sqmm earth wire.

M & L concealed sub main wiring with 2 runs of 2.5 sqmm main wire along with 1 run of 2.5 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

All as per item No. 139 above but with 2 runs of 4.0 Sqmm main wire along with 1 run of 4.0 Sqmm earth wire.

All as per item No.139 above but with 2 runs of 6.0 Sqmm main wire along with 1 run of 6.0 Sqmm earth wire.

S&F of rigid non metallic PVC conduit 20 mm dia (for lan cable / TV cable) inclusive of Tees, bends, elbow, reducers and fixing accessories concealled on wall including nessary cutting/ chasing of wall and making good disturb surface complete all as specified and directed.

S&F switch piano modular type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano modular type one way, 15 /16 Amps independent, 240 volt complete all as specified and directed.

S&F socket outlet modular type 3 pin 5 / 6 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F socket outlet modular type 3 pin 15/16 Amps, 240 volts combined 2 modular complete all as specified and directed.

M&L for Single pole blanking plate for distribution board complete all as specified and directed.

S&F MCB SPN 40 Amp, 10 kA, 240V 'C' curve including taking down complete all as specified and as directed.

S&F MCB SP 6 to 32 Amp, 10 kA, 240V 'C' curve including taking down complete all as specified and as directed.

S&F ceiling rose, 3 phase / PVC / polycarbonate isolated body complete all as specified and directed.

S&F modular type electronic fan regulator, flush type 230V, AC 50 Hz not less than 100 Watt complete all as specified and directed.

S&F in repairs of decorative wall mounted bathroom light fitting with moisture proof sealed fittings and not less than 9W high bright LED with B22 socket type complete all as specified and directed by the Engr-in-Charge. Make :- Any approved make conforming to above specifications

S&F lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings including taking down old unsv ones complete all as specified and as directed.

S&F MCB protected Power unit with one 25 amps socket, (including 3 pin plug top) including MCB DP and starter 25 amps rating with six module plate and flush PVC box and electrically connecting up fixed complete all as specified and directed.

S&F MCB DB, SPN 8 way, IP-43, IK 09, double door type with metal door, with 100A copper neutral and earth bus bar for fixing MCB, fixing flush to wall & making good the disturbed surfaces including taking down complete all as specified and as directed.

S&F VTPN DB,MCCB incomer,4 ways double door, Metal door ,IP-43 IK 09 in 250A rated copper bus bars,earth bar,neutral links, no. of module DPX 250+12 complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down old unsv ones complete all as specified and as direct.

S&F MCCB 4P 125 Amps 415V ,50 Hz ,breaking capacity 16 KA Including dismantling taking down unsvericeable one complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized iron earth lead wire of 4 sqmm by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, P.C.C (1:3:6) type C-I with 50 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth wire protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion including dismantaling old unserviceable ones complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing TV Socket complete all as specified and as directed by the Engineer-in-Charge.

S &F in repairs Bell buzzer, Ding Dong AC. 230 volts, single pole completed all as specified and directed.

S&F Exhaust fan 250 mm sweep, non metallic blades plastic body with louver shutter, AC single phase, 230 V, 50Hz with & including self closing louvers, nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan and writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole awriting MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed. Note :- Old unsv fans retrived from site deposited to the AGE EM Fan section and rate for the same is deemed to be included in the quotated rate.

S&F exhaust fan 300 mm sweep, heavy duty, metal body and metal blades grey1400 RPM (minimum), AC single phase, 230 V, 50Hz with bird guard, nuts, screws, bolts including electrical connection, writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed. Make :- Crompton/Bajaj/ Orient / Ram Ratna Electricals Ltd (RRE)

S&F energy saving BLDC ceiling fan complete with all connected accessories as specified below: - Input Power: - 26 watts with full speed and reduced power consumption with reduced speed technology. Voltage: - 90-300 V AC, 50Hz, single Phase. RPM: - 340 to 375 rpm Blades: - Decorated Sweep: - 1200 mm. Air delivery: - Not less than 210 CFM Colour: - Glow white/Toast Brown/Gloss Black/or others as approved by Engr-in-Charge Speed/power control: -Without Remote through existing regulator. Star rating: - BEE 5 Star Rating Warranty: - As specified by the manufacturer, contractor shall produce original warranty and test certificate from the manufacturer. Note:- Old unserviceable fan shall be deposited to MES store labour cost for the same is deemed to be included in the item rate.

Taking down old ceiling fan complete all as specified and as directed.

S & F Bell push, flush type, 5 Amps single pole complete all as specified and as directed.

S&F in repairs of surface & wall mounted LED decirative bracket light fittings with 9/10 w indoor / outdoor luminaries with and including electronic driver and LED Lamp, pre-wired including necessary electric connection from ceiling rose to light fitting, conforming to the following specification :- (i) System watts/lumens :- 9 to 10w/Total system lumen not less than 800 Lm. (ii) Housing :- Extruded polycarbonate / engineering plastic (iii) IP rating :- IP 65 (iv) Front cover :- PRISMATIC DIFFUSER (v) Mounting :- Suitable for wall / ceiling mounting (vi) Finish :- Smooth finish (vii) Lamp :- SMD LED high bright (viii) Heat sink :- As per OEM's design

S&F in repairs recess mounted LED down light fittings square type with 12 w indoor luminaries with and including electronic driver and LED Lamp, pre-wired including necessary cutting of ceiling making good, electric connection to light fitting, conforming to the following specification :- (i) System watts/lumens :- 12W/Total system lumen not less than 1200 Lm. (ii) Housing :- Extruded Aluminium (iii) IP rating :- IP 20 (iv) Front cover :- Acrylic / polycarbonate cover frosted (v) Mounting :- Suitable for ceiling recess mounting (vi) Finish :- Smooth finish (vii) Lamp :- high bright LED (viii) System Efficacy (Im / Watt) :- Not less than 100 lm/watt (ix) Colour Temperature :- Not less than 5700k (x) Colour rendering index (CRI) :- Not less than 80 (xi) Life :- Not less than 25000 hrs of operation (xii) Optics :- Designed for optimum light distribution (xiii) Control gear :- Inbuilt electronic driver with APFC, PF not less than 0.95, and THD not more than 20% of the standard operating voltage 180-270V Ac, 50Hz (xiv) Surge protection :- Inbuilt surge protection minimum 2KV (xv) Heat sink :- As per OEM's design

S&F in repairs LED battery backup inverter bulb of Lamp wattage: - 9 to 12 Watts, Battery: - Not less than 2200mAh or not less than 4 hrs backup,Efficeacy: - Not less than 110 Lm/Watt including taking down old unsv ones complete all as specified and directed.

S&F geyser of 2KW of capacity 25 Litres, 230V, 50Hz, vertical, wall mounted type, BEE 5 star rated, steel outer body and copper inner tank with, incoloy glass coated heating element, adjustable thermostat for temperature regulation, multifunctional safety valve with & including 3 core copper cable of 1 to 2 metre length with 3-pin plug of 16A capacity, fixing arrangement such as. bracket, nuts, bolts washers etc. complete all as specified and directed.

S & F in repair Surface and wall mounted LED batten 10 watt 2ft long with Aluminum extruded housing , high quality polycarbonate diffuser & integrated Electronic Driver with IP20, PF 0.95, Efficiency not less than 110 lm / W color temp 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V complete all as specified and directed.

S & F in repair Surface and wall mounted LED batten 20 watt 4ft long with Aluminum extruded housing , high quality polycarbonate diffuser & integrated Electronic Driver with IP20, PF 0.90, Efficiency not less than 110 lm/W color temp 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed. Make : Crompton, Cat no - LUMILINEPLUSBS20WLED865SPCSS / BCLSB 20W WH OF BAJAJ / Havells.

S&F LED street / security light fitting 1 x 20 watt, integrated type with high efficiency electronic driver, pressure die cast aluminium housing & PC diffuser, Lumen Efficacy 100 Lm/Watt (minimum), colour temperature 5700K (minimum), CRI 70 (minimum), IP-65 (minimum), PF 0.90 (minimum), THD 10% (Maximum), in-built surge protection 5 KV (minimum) internally prewired and including electrically connecting with twin core twisting flexible cord of 0.75 sqmm copper conductor cable & all other necessary fixing accessories such as GI pipe light grade of 40 mm bore (or higher size as per manufacturer recommendation) & suitable length with MS flat iron clamps (clamps shall be 40 x 5 mm MS flat), nuts, bolts & washers including painting to GI pipe & clamps with two coat of aluminium paint over a coat of red oxide primer complete all as specified & directed.

S&F Metal Plug Socket DB with sheet metal enclosures with two pin and earth plug and socket one double pole MCB 20 Amps, 240V for Geysor connenction complete all as specified and directed.

PS ENTERPRISE (BID ID -3195856)

M/S ASHRAFI CONSTRUCTION (BID ID -3196000)

G C DUTTA N CO (BID ID -3196244)

MS ESSCON (BID ID -3195897)