REPAIR/ MAINTENANCE TO DOORS, WINDOWS, VENTILATORS, CUPBOARDS, FLOORING, PLASTERING, TILING, SANITARY FITTING AND OTHER MISC. WORK IN TECHNICAL AREA UNDER GE(AF) SRINAGAR

Amount

Demolition of cement concrete (unreinforced) in ground floor and in paving n exc 15 cm thickness (below or above ground level), complete all as specified.

Dismantling wall and ceiling boards, fibre pulp insulation etc or insulation boards/slabs/ blankets, any thickness, including cover fillets, all as specified.

Dismantling of Plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings including ridges, hips, valleys and flashings etc complete all as specified and as directed by Engineer-in-Charge. Note:- (i) The rate quoted shall also be deemed to include for taking down of wind ties.

S&F 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, with L-type or J-type or cranked hook bolts, in roofs, walls etc. with grade of zinc coating 275 complete.

All as per item No 4.00 but except Sheets using sheet retrived vide item No 03 above Note For Item No 4 & 5:- Quoted Rates shall be deem to include for Fixing only Wind Tie retrived from BOQ Item No 03

S&F 0.80 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275

M&L for Preparation of new zinc (or galvanised) steel and iron roof surfaces of any description over 10 cm width or girth to receive painting, by coating with mordant solution including washing and cleaning, etc and applying two coat of synthetic enamel paint over one coat red oxide primer complete all as specified and directed by Engineer-in-Charge

M&L for tightening bolts and closing bolt holes etc. in old corrugated steel sheets or Aluminium sheeting by sealing with one bitumen and one curved GI washer on either side and 6 mm G.I. bolts and nuts, all set in stiff white lead, bolt n exc 25 mm in length complete all as specified and directed by Engr-in-Charge.

M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre, intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

M&L for Providing and fixing Gypsum Board 12 mm thick (water proof) in ceiling fixed with screw or as per manufacturers instructions including necessary jointing and taping, and applying two coat oild bound distemper over one coat primer and 1 mm thick cement base putty complete all as specified and directed by Engr-in-Charge.

S&F false ceiling of Non asbestos fibre cement building boards, manufactured from homogeneous mixture of cement, quartz and cellulose and cured with high pressure steam using auto claving process confirming to IS-14862, of size 600 mm x 600 mm x 6 mm thick fixed over and including anodised aluminium powder coated (minimum thickness of powder coating 50 micron) snap grid frame work of T section (main & cross member) of size 25 mm x 25 mm x 1.5 mm thick in square pattern of grid size 600mm X 600mm . The aluminium fram work will supported on side wall with the used of aluminium 'L' section of size 25 mm x 25 mm x 1.5 angles etc. Snap grid shall be supported with hangers of 4 mm dia. Galvanised iron wire adjusting level fixed to roof slabs / truss etc by means of ceiling cleats made out of Galvanised iron flat of size 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long complete all as specified directed by the Engineer-in-Charge.

S&F in repairs 12 mm thick Particle board for insulation purposes as in false ceiling, fixed with nails to timber framework design and pattern of board as approved by Engr-in-Charge.

S&F for pre-painted galvaume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified.

S&F pre-painted galvaume aluminium zink coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof ridges, fixed with self tapping screws as specified, complete all as specified.

M&L for second class hardwood fillets bullnosed, splayed, chamfered or rounded on one edge or face sectional area exc 06 Sqcm but not exc 13 sqcm, fixed in repairs, secured with screws, complete all as specified and directed by Engineer-in-Charge.

M&L for second class hardwood fillets bullnosed, splayed, chamfered or rounded on one edge or face sectional area exc 13 Sqcm but not exc 25 sqcm, fixed in repairs, secured with screws, complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster of any description on brick or stone masonary wall , etc including racking out joints, hacking for key, scrubbing down with water etc, all as specified.

M&L for Rendering 15 mm thick in cement and sand mortar 1:4 on brick work or cement concrete surfaces of walls including finishing the surface even and smooth with using extra cement and mixing only integral water proofing compound as per manufacturer instruction complete all as specified and as directed by Engineer-in-Charge. Note:- WPC will be measured and paid seperately.

M&L for Rendering 15 mm thick in cement and sand mortar 1:6 on brick work or cement concrete wall surfaces including finishing the surface even and smooth without using extra cement complete all as specified.

M&L for Rendering 15 mm thick in cement and sand mortar 1:4 on brick work or cement concrete wall surfaces including finishing the surface even and smooth without using extra cement complete all as specified.

M&L for Rendering 5 mm thick in cement and sand mortar 1:3 on concrete surfaces of ceiling, including finishing the surface even and smooth without using extra cement complete all as specified.

Supply only integral water proofing compound.

M&L for Wooden panelling of second class softwood 12 mm thick with tongue and groove joint fixed in any position over and including wooden framework in second class softwood with plain fillets square or sectional area exc 13 Sqcm and n exc 25 Sqcm at n exc 90 cm centre to centre in both direction and including two or more coat of french polishing on all the exposed surfaces wooden panelling including taking down existing electrical fittings and re-fixing the same, complete.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.50 Sqm each complete all as specified and as directed by the Engineer-in-Charge

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 Sqm but n exc 4.00 Sqm each complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description, area exceeding 1 sqm and not exceeding 2.00 sqm each complete all as specified and as directed by Engineer-in-Charge

Resecuring or easing & adjusting old wooden shutters of any description area exc. 1 Sqm and not exc. 2 Sqm each without taking down shutters, complete all as directed by Engr-in-charge.

M&L for Pressed steel frames 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, lock strike plates complete, providing mild steel 6 mm dia thresh old bar, thickness of sheet 1.25 mm and filling hollow of frame with plain cement concrete Type C-0, 1:3:6 (using 12.5 mm graded crushed stone aggregate) complete, all as specified.

M&L for Pressed steel frames 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, lock strike plates complete, providing mild steel 6 mm dia thresh old bar and filling hollow of frame with plain cement concrete Type C-0, 1:3:6 (using 12.5 mm graded crushed stone aggregate) complete, all as specified.

S&F 35 mm thick, IInd class hard wood plain, framed, panelled factory made shutters (two panel) with lock rail and panel of 12 mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified & as directed by Engineer-in-Charge.

S&F 35 mm thick, 2 nd class hard wood, glazed & skeleton factory made shutters, open rebated and prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.24(a) complete all as specified and as directed by Engineer-in-Charge.

S&F 30 mm thick, 2nd class hard wood, glazed & skeleton factory made shutters, open rebated and prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.24(b) complete all as specified and as directed by Engineer-in-Charge.

S&F door strip comprising of aluminium holds & rubber strip fixed at bottom of door shutter with screws complete all as specified and as directed by Engineer-in-Charge

S&F 150 mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F 300 mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete.

S&F Hasp and staple, 100 mm size, ISI marked safety type, of aluminium anodised with mild steel hinge pin including bolts to hinge plate, fixed with screws complete all as specified and as directed by Engineer-in-Charge.

S&F Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F Aluminium handles cast type anodised of size 125 mm long ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 100 mm size mild steel mortice lock, for aluminium door, with 2 brass levers and duplicate key complete all as specified and directed by Engineer-in-Charge

S&F Floor door stopper of aluminium alloy body, double legged with rubber shoe fixed to door, Overall length of cover plate 140 mm all as specified and directed by Engineer-in-Charge

S&F in repair IInd class hard-wood, small fittings such as bracket of any sizes, hinge blocks, cleats, door / window stoppers and like articles not exceeding 200 cubic centimetres each complete all as specified and as directed by Engineer-in-Charge.

S&F Steel windows with side hung shutters including box type hinges with steel handle, steel peg stay & hold fast and glazing bars, dovetailed or welded complete.

S&F Steel windows with side hung shutters including box type hinges with steel handle, steel peg stay, & hold fast, and without glazing bars, dovetailed or welded complete.

S&F fixed type Steel windows / ventilator including hold fast, and with glazing bars, dovetailed or welded complete.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Gde-E-165

S&F Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified.

S&F in repair Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / metal frames or stone, concrete or brick surrounds glazed with oil putty or fixed with beads not exceeding 1.5 Sqm complete all as specified and as directed by Engineer-in-Charge.

S&F 03 mm thick sheet glass, ordinary quality and glazing with oil putty / wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed by Engineer-in-Charge.

S&F 03 mm thick sheet glass, figured glass, pin head type and glazing with oil putty / wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed by Engineer-in-Charge.

M&L for cutting chases pinning in making good to facing where required and pointing in cement mortar (1:3) for concealed water tubing in brick walls cutting n.exc 10 cm girth complete all as specified and directed.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc complete all as specified and as directed by Engineer-in-Charge.

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc complete all as specified and as directed by Engineer-in-Charge.

S&F 15 mm bore tubes, 'medium grade', galvanised, with all fitting; ( such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed to wall / ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified.

S&F 20 mm bore tubes, 'medium grade', galvanised, with all fitting; ( such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed to wall / ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified.

Refixing old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 15 mm bore after cleaning including provn of new fittings all as directed by Engineer-in-Charge (using old steel tubing retrived from item No 52 above).

Refixing old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 20 mm bore after cleaning including provn of new fittings all as directed by Engineer-in-Charge (using old steel tubing retrived from item No 53 above).

S&F in repair 15 mm size Bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed by Engineer-in-Charge

S&F in repair 15 mm size Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 20 mm size Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs for 15 mm size bib taps fancy type, cast copper alloy chromium plated, with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed, all as specified.

S&F in repairs for 15 mm size two way bib taps fancy type, cast copper alloy chromium plated, with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed, all as specified.

S&F in repairs for 15 mm size angle cock fancy type, cast copper alloy chromium plated, with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed, all as specified.

S&F in repairs for 15 mm size two way angle cock fancy type, cast copper alloy chromium plated, with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed, all as specified.

S&F in repair PVC connection 15 mm size, of length 600 mm, with PTMT nuts complete all as specified and as directed by Engineer-in-Charge

S&F in repair Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20 mm dia (minimum weight 210 gms) complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Tubular towel rail stainless steel chromium plated 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, complete all as specified and as directed by Engineer-in-Charge.

S&F in repair brass chromium plated shower roses with swil joints, 125 mm size in square with CP long shank arm including fixing to steel pipe or union, complete all as specified and as directed.

S&F in repair 300 mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate, ISI marked complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repair white vitreous China wash hand basin (Flat back) of size 550 x 400 mm fixed on and including new brackets complete including, 32 mm size brass chromium plated waste coupling, chain and plug and porcelain stopper, etc complete.

Supply and fix in repairs white vitreous china squatting pan ‘ORISSA’ pattern of size 580 mm x 440 mm white with integral foot rests with ‘P’ or ‘S’ trap, front or back inlet including all connection and provision of lime concrete base complete all as specified and as directed..

S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, Plastic water closet seat cover, white, closed pattern with flat bottom, and cover with aluminised hinging device, brass chromium plated Jet shower with one meter long flexible pipe including all connection complete.

S & F in repair white vitreous china floor mounted coupled EWC of size 380 mm x 725 mm x 690 mm including UF soft close slim seat cover, hinges, fixing accessories, accessories set and Cistern Fittings complete all as specified and directed. Make of Cistern & EWC: Jaquar model No- ONS-WHT-10853S300UFSM or equivalent cat No of make mention Appx A.

S&F in repair Vitreous China urinal half stall type, white, with grating and union for discharge pipe and including waste pipe (excluding flushing cistern), complete including providing and fixing plugs,bedding urinal agaist wall in CM 1:2 securing urinals to plugs including 60 mm long brass screws including brass chromium plated urinal spreader for fixing with 15 mm dia pipe all as specified and directed by Engineer-in Charge

S&F in repair PVC low level flushing cistern, valveless, syphonic action type, double push botton, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 32 mm dia of required length and making connection complete complete all as specified.

S & F in repairs Stainless Steel Soap dish, fixed to plugs with chromium plated brass screws Complete all as specified and directed by Engineer-in-Charge.

S&F Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2020 as specified and as directed by Engineer-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in drawing of relevant item in MES schedule Part-II , 2020 as specified and as directed by Engineer-in-Charge.

S&F in repair 20 mm Dia Curtain rail, stainless steel chromium plated, fixed with bracket and end caps etc including taking down of existing curtain rail, complete all as specified and directed.

M&L for applying 2 mm thick cement base wall care putty on plastered surface of wall, and making the surafce even & smooth for reciving distemper / paint of any descreption all as specified & directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over one coat of primer all as specified and directed. Note:- Cement base wall care putty where ever directed will be applied and will be measured & paid seperatly

M&L for Preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge

M&L for Preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge

M&L for Preparation of old decorated surfaces of walls, pillars, cornices by brooming down or steel brushing, scraping down smoke roots. moulds , moss and efflorescence salts, trading oil greasy spots etc. and applying one coat of oil bound distemper after removal of nails & filling nail hole with putty complete all as specified and directed by Engineer-in-charge.

M&L for Preparation of old decorated surfaces of ceiling and applying two coats of white wash complete all as specified and as directed by Engineer-in-Charge

M&L for preparation of newly plastered surfaces of walls including sides and soffits of beams, fascias, parapets etc and applying two coats of cement base paint over one coat of primer, colour and tint as ordered, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old plastered surfaces of walls including sides and soffits of beams, fascias, parapets etc and applying one coat of cement base paint, colour and tint as ordered, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new wooden surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of primer complete all as specified and as directed by Engineer-in-Charge.

M&L for Preparation of old painted wood and wooden base surfaces of any description over 10 cm width or girth and painting with one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified

M&L for Preparation of old painted steel surfaces of any description exc 10 cm width or girth and painting with one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 15 mm size wall mixer for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 15 mm size sink mixer for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 15 mm size central hole basin mixer for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe including 450 mm long braided connection pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stainless steel sink, 1.00 mm thick for kitchen or laboratory, with plug, washers, waste pipe including bedding in cement mortar on to draft wall or including fixing cantilever brackets, connecting union to pipe etc, overall size 495 mm x 420 mm, with bowl size 405 mm x 355 mm x 178 mm, including waste assembly, complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm including waste assembly, complete all as specified and directed.

S&F in repair Steel plate rack made of 0.63 mm thick stainless steel sheet over all size 600 mm x 750 mm complete all as specified and as directed by Engineer-in-charge.

S&F in repair 75 mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete.

Demolition of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including rubbish off the premises, all as specified.

M&L 15 mm thick screed or bedding layer in cement mortar (1:6) for laying floor finishes, complete all as specified.

M&L for 10 mm thick rendring / backing coat in cement mortar (1:4) to receive wall tiles, complete all as specified.

M&L for 25 mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in leveling layer for floor complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.16 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match, all as specified.

M&L for coloured glazed ceramic tiles in vertical surfaces of size 600 x 300 x 7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified.

M&L for double charged colour vitrified ceramic tiles 10 mm thick (square) polished, area of each tiles n.exc 0.36 sqm in floors etc laid over existing screed bed, set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for double charged colour vitrified ceramic tiles 10 mm thick (square) polished, area of each tiles n.exc 0.36 sqm for skirting / dado etc laid over existing backing coat, set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for Lagging to pipes 15 mm bore used in external water supply or plumbing all around with 50 mm thick bonded mineral wool pre-formed ‘SNAP ON’ pipe sections of density 144 Kg /Cum conforming to IS 9842 provided with chicken mesh wire netting 25 gauge 20 mm mesh complete including taking down of old lagging all as specified and directed by Engineer-in-Charge

M&L for Lagging to pipes 20 mm bore used in external water supply or plumbing all around with 50 mm thick bonded mineral wool pre-formed ‘SNAP ON’ pipe sections of density 144 Kg /Cum conforming to IS 9842 provided with chicken mesh wire netting 25 gauge 20 mm mesh complete including taking down of old lagging all as specified and directed by Engineer-in-Charge

M&L for Lagging to pipes 25 mm bore used in external water supply or plumbing all around with 50 mm thick bonded mineral wool pre-formed ‘SNAP ON’ pipe sections of density 144 Kg /Cum conforming to IS 9842 provided with chicken mesh wire netting 25 gauge 20 mm mesh complete including taking down of old lagging all as specified and directed by Engineer-in-Charge

M&L for 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including half round molding of exposed edge complete all as specified.

S&F in repair Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified.

S&F in repair Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified.

S&F in repair, PVC flexible waste pipe, 32 mm bore for WHB & sink complete all as specified and directed by Engineer in Charge.

S&F in repair ABS plastic chromium plated Health faucet fixed with spring action and lever along with Flexible hose with brass nut of length 1 m to 1.2 m fitted in the existing water connection in the toilets, Complete all as specified and directed by Engineer-in-Charge.

S&F in repair brass chromium plated Jet Spray of Standard size for EWC alongwith CP connection and all fittings as fixed, complete all as specified and directed by Engineer-in-Charge.

S&F in reapir Toilet paper holder cast copper alloy chromium plated fixed to walls with chromium plated brass screws, complete all as specified and as direted by the Engr-in-Charge

S&F in reapir PVC seat cover for EWC colour white including hinges, complete all as specified and as direted by the Engr-in-Charge.

S & F in repairs 20 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair brass spindle with nylone washer to Brass chromium plated bib taps, stop cocks, pillar taps, wall / sink mixer etc, complete all as specified and as direted by the Engr-in-Charge.

S&F in repair Glass Shelf of size 500 mm x 125 mm wide with stainless steel wire guard fixed on wall with and including bracket and brass screws and wooden / plastic cleats.

S & F in repair Corner Glass Shelf of size 300 mm with stainless steel wire guard fixed on wall with and including bracket and brass screws and wooden / plastic cleats. Make:- Prayag or equvallent make mention in Appx A.

Supply and fix in repair 500 litres capacity double layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete

Supply and fix in repair 1000 litres capacity double layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete

Taking down aluminium glazed door shutters of size exc 1.5 Sqm but n. exc 2.0 Sqm (each leaf), & S&F in repair of hard ware fitting such as stainless steel top & Bottom patch, Pivot, tightening of joint and adjustment of floor door spring and refixing shutters in same positioning for smooth functioning complete. Note:- Floor door spring if found unserviceable same will be replaced & will be measured & paid separately under respective item of this BOQ.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty.

S&F in repair Aluminium (Extruded Section body) Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed in position complete.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 9 mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size, 100mm size mortice lock and hinges etc all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4 mm ( Section No 14021)

(b) Vertical Members of shutter Section shall be be of size 85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section shall be be of size 83.50 x 44.45 x 2.00 mm (Section No 19581) (d) Lock rail (Middle member) of shutter Section shall be be of size 150.00 x 44.45 x 3.00 mm (Section No 19596) (e) Bottom Members of shutter Section shall be be of size 150.00 x 44.45 x 3.10 mm (Section No 19584) Note: (i) Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx A

Supply fabricate & fix in position aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) three track window ( two shutters glazed & one shutters wire gauge) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below, including taking down old steel window complete all as specified and directed. (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20831)

(b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20832) (c) Top & side Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55 (Section No 20738) (d) Shutter Interlock Section shall be be of size 18.00 x 40.00 x 1.45 (Section No 20737) (e) Bottom Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55 (Section No 20736) Note:- (i) Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx A

S&F aluminium powder coated minimum thickness of power coated 50 micron of approved colour ventilator, partially glazed and partially louvers, outer frame & mullion fabricated with aluminium section of size 82.50 mm x 38.00 mm x 1.50 mm thick (Cat No 20036), half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portion louvers of 80 mm wide & 4 mm thick frosted glass including aluminium louver patti including S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aperture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position including taking down old steel ventilator complete. Note:- (i) Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx A

S&F in repair 12 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work including 4 mm thick teak wood lipping, on exposed edge fixed with nails complete all as specified.

S&F in repair 18 / 19 mm thick Block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work as in Kitchen drawers etc.

S&F 0.90 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions

S & F Magnetic type catch fixed with screws to door frame complete all as specified and directed by Engineer-In-Charge.

S&F Piano type hinges of brass with 30 mm flap width complete all as specified and directed by Engineer-In-Charge.

S & F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. and removing debries from site all as specified and directed.

Demolition of RCC selves / cooking plateform (reinforement cut as required to facilitate demolition) and similar suspended work and removing debries form site all as specified and directed.

M&L for brick work with sub class 'B' Bricks (using old size bricks) straight or curved on plan exc 6m mean radius, built in CM 1:4, complete all as specified and as directed.

All as per item No 140 above here-in-before but except bricks. Note:- Old brick retrieved vide item No 138 above shall be reused.

M&L for Brick work with sub class 'B" (using old size bricks) straight or curved of on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified.

M&L for RCC 1:2:4 using, type B0, using 12.5 mm graded stone aggregate as in selves / cooking plateform and similar work complete all as specified & directed.

M&L for form work to soffits & side of selves / cooking plateform flat, fair finished surfaces of concrete not exceeding 100 mm thick complete all as specified & directed.

M&L for mild steel TMT bars 10 mm dia and over cut to length bent to shape including cranking bending spirallay for hooping for columns hooking end and binding with and including mild steel wire (annelead) not less than 0.9mm dia or scuring with clips.

M&L for 75 mm thick PCC type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection laid in bays n. exc. 2 sqm each, finishing the surface of concrete topping even & fair, without using extra cement filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand (all by weight) complete all as specified and as directed by Engineer-in-Charge.

M&L for 40 mm thick PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in flooring including finishing the top surface even and smooth, without using extra cement complete all as specified and as directed by Engineer-in-charge.

S&F Glass dividing strips, 3 mm thick, 38 mm wide, fixed in position with cement mortar complete all as specified.

M&L machine cut kota stone slab flooring 20-25 mm thick as in floor, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, laid over and including 20 mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in -Charge.

M&L machine cut kota stone slab flooring 18 - 20 mm thick as in dado / skirting, risers of steps laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, laid over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed by Engineer-in -Charge.

M&L for rubbur molded glossy finish Chequered cement concrete tiles of size 30 cm x 30 cm x 25 mm thick, in white cement with pigment, set, jointed in neat cement slurry & pointed in coloured cement, as in floors / path / hardstanding, laid over screed bed complete all as specified and directed.

M&L for 100 mm thick cement concrete 1:4:8, type D-2,(using 40 mm graded stone aggregate) as in Sub base for path / flooring complete all as specified and as directed.

M&L for sand cushioning over PCC surfaces, for laying of interlocking tiles, spread rolled and consolidated to gradient as required.

Material & Labour for machine pressed precast concrete interlocking paver block of approved shape and size of 80 mm thickness, with minimum compressive strength of 40 N / Sqmm (M-40 grade), without correction factor for chamfering, made in rubber moulds with 0.50 mm thick scratch proof lacquer coating on top surface, with white cement and pigment laid in path / hardstanding complete

M&L for Dismantling wrought iron or mild steel work of any description not otherwise provided for.

S&F steel work in tubular Post / trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St-240 including all necessary work as directed by Engr in Charge. Complete all as specified.

S&F mild steel, plates (Plain or Chequered) Channels, square cut or notched (ordinary and counter sunk) forming holes,without any attachment as required FE 410-W(Gde-E-250 quality-A) complete all as specified.

S&F rolled mild steel section as in main and cross beams, hip and jack rafters; purlin where connected to common rafters and running rails and guides for for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410-W (Gde-E-250 quality A).

S&F Mild steel, screw bolt machine made with hexagonal or square heads at one end and screwed the other end with washer and one hexagonal or square nut exc 5 cm and n exc 10 cm long and 5 to 10 mm dia complete all as specefied.

Supplying, fabricating and fixing wall clading of aluminium composite panel of any colour / any shades approved, made out of 4 mm thick aluminium composite panel material consisting of 3 mm thick mineral core sandwiched between two aluminium sheets (each 0.5 mm thick). The aluminium composite panel sheet shall be coil coated, with Kynar 500 based PVDF lumiflon based fluoropolyer resign coating of approved colour and shade on exposed face and polymer (service) coating on other face fixed over and including frame work fabricated with aluminium square pipe of size 25 mm x 25 mm with 1.5 mm wall thickness including stainless steel screws, nuts bolts, washers cleats, weather silicone sealant for groove filling etc complete all as per manufacturer instruction including old clading all as directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation, filling, mass concrete complete.

Material and labour 1st quality vitrified parking tiles of approved shade, of size 300 mm x 300 mm x 10 mm thick as in floors / path etc, set & jointed in neat cement slurry & pointed in matching coloured polymer cement based grout to match complete. Make :Johnson Endura meteor (Korneto Biege) or equivalent make mention in Appx A.

Dismantling timber scantlings 40 sq. cm and over in section, in any position in unframed work

S&F in repair 1.5 mm thick Polycarbonate sheet fixed with self tapping stainless steel screw and washer complete all as specified and directed by Engineer-in-Charge.

S&F Solar control film 25 micron thick reflective type sticked to glass panes as per instructions of manufacturers

S&F in repair 12 mm thick toughned glass as in doors, partitions and similar work including cutting to shape, drilling holes required and machine molding edges complete

M&L for etching on toughened glass designed and pattern as approved by Engr-in-Charge

S&F stainless steel handle 450 mm size & 25 mm dia suitable for toughened glass door complete all as specified and directed by Engineer-in-Charge.

S&F 2 levers stainless steel floor lock suitable for toughened glass door complete all as specified and directed by Engineer-in-Charge.

S&F in repair superior quality venetian blinds horizontal or vertical type including Powder coated hardware fitting complete all as specified and directed by Engineer-in-Charge.

M/S TARIQ AHMAD SHEIKH

M/S A.R.TANTARY

M/S FAROOQ AND SONS

M/S WANI AND SONS

M/S LUCKY BUILDERS

NAJAR ENTERPRISES