Construction of Tilting flume under NHP at CWPRS Pune 24

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix).

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size

Brick work with common burnt clay second class (non modular) bricks of class designation 3.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand

Cement plaster 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement.20 mm cement plaster

20 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing,fixing and commissioning of 12 mm thick glass panel (Toughened)in existing wooden and M.S. frame by applying lambi/white zinc making it water tight as per enclosed drawing ect. complete and as directed at site by Engineer-in-charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length.Second class teak wood.

Providing and fixing precoated colour galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge)0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 micronsepoxy primer on both side of the sheet and polyester top coat 15-18microns. Sheet should have protective guard film of 25 micronsminimum to avoid scratches during transportation and should besupplied in single length upto 12 metre or as desired by Engineer in-charge. The sheet shall be fixed using self drilling /self tappingscrews of size (5.5x 55 mm) with EPDM seal, complete upto anypitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shapewherever required.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces.

Providing, installing and commissioning of Electrically operated Hydraullic Power Pack of 120 ltr, 7.5 Hp motor with 20 LPM pump or necessary capacity for uplifting load of 25 tonnes , along with Hydraullic cylinder for both end Clevis Bore 150 x Rod 90 x Stoke 500 including pivot assembly with roller guide and Hydraulic jack assembly arrangement to control the vertical movement of tilting flume upto 500mm etc. all complete and as directed by model officer and Engineer-in-charge.

Supplying, Installation, Commissio- ning and testing of end suction pump of flow rate 100 LPS and a head of 10 m of and TEFC/Sq Cage Ind. Motor With MS Base Plate, Coupling, Coupling Guard, including Cement Concrete foundation etc complete as directed by the Engineer in charge

Supplying, installation, testing and commissioning of logical control panel with a provision of 20 HP starter (1 working and 1 standby) with auto switch ,timer and including "A" meter, "V" meter, phase preventers, Dry Run Protection, O/L Indication, timer for start up, with relays & contactors with all necessary accessories including cabling from motor to control panel etc complete as per the directions of engineer-in-charge

Supplying, installation, testing and commissioning of logical control panel with a provision of 20 HP starter (1 working and 1 standby) with auto switch ,timer and including "A" meter, "V" meter, phase preventers, Dry Run Protection, O/L Indication, timer for start up, with relays & contactors with all necessary accessories including cabling from motor to control panel etc complete as per the directions of engineer-in-charge

Providing, and laying of suction and delivery pipe line of MS 200 mm NB, thickness of 6 mm including fabrication etc complete as directed by the Engineer in charge.

Providing, installation, testing and commissioning of MS long bend 200 mm with all accessories etc all completed as directed by the Engineer in charge.

Providing, installation, testing and commissioning of 200 mm dia Non return Valve PN 16 with all accessories like Nut bolts, rubber packing etc all completed as directed by the Engineer in charge.

Providing, installation, testing and commissioning of 200 mm dia foot valve with all accessories like Nut bolts, rubber packing etc all completed as directed by the Engineer in charge.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Painting (two or more coats) on rain water, soil waste ,SS/MS pipe and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work.upto100 mm diameter pipes

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work.

Supply, Installation, Commisioning and testing of 5HP Vacuum pumps DV 40model and TEFC/Sq Cage Ind. Motor with MS Base Plate, Coupling, Coupling Guard, including CC foundation etc complete as directed by the Engineer in charge.

Supplying, Installation, Commissioning and testing of 5HP starter for Vacuum pumps including cabling for connection to pump and motor etc complete as directed by the engineer in charge

Sujit P. Mate