REPAIR OF MISC FURNITURES ISSUED TO OFFICERS AND JCO ORS MD ACCN UNDER GE NORTH DELHI CANTT 10

Amount

CHARPOY GI PIPE PLY TOP /CHARPOY IP HARD TOP

S&F in repairs to 12mm thick plywood BWR Grade, single piece of approved quality with suitable steel screw and cup washer including removal of damaged plywood and 2 no. of MS Flat iron of size 40*6 mm shall be fixed over long rails with nut and bolt duly painted with two coat of synthetic enamel paint over a red oxide primer ,rest all as shown on drg and complete all as specified and directed

Taking out old damaged & worn out following parts of charpoy GI pipe and replace the same with new part without damaging other parts all as per drg or complete all as specified and directed

LONG RAIL: Made of 32mm dia GI pipe medium grade ISI marked of approved make including both side threading complete all as specified and directed

SHORT RAIL: Cutting the unserviceable portion from existing unserviceable long rail obtained from Sl item 1.03 here-in-before and converting into short rail including threading both side and fixing the same in the existing charpoy frame complete all as directed.

LEGS: Cutting the unserviceable portion from existing unserviceable short rail obtained from Sl item 1.04 here-in-before and converting into legs including threading one side for screwing and other side/bottom of leg should be covered with 4mm thick round MS plate complete all as specified and directed

S&F in repairs GI Elbow 32 mm dia three way medium grade of approved make suitable for fixing the long rail/short rail/legs rest all as shown on drg and complete all as specified and directed

S&F of GI check nut 32mm,6mm dia siutable for fixing long rail and short rail complete all as specified and directed.

Removal of existing worn out paint including preparation of surface complete of the Charpoy IP Hard Top and M&L for applying two coats of 1st quality synthetic enamel paint of black colour and make, over a coat of red oxide primer, rest all as shown on drg and complete all as specified and directed

BED PLY TOP WITH MNF SET/BED HARD (STEEL)

S&F 12mm thick plywood BWR Grade, approved quality in single piece as per drawing without any joint to the bed frame with suitable screws/nut bolt including removal of damaged ply wood all as specified on drawing or complete all as specified and directed

S&F in reapirs to 4mm thick one side teak finished plywood of size 780mm x 340mm including 12mm dia half cut teak wood beading of both side of head board including removal of damaged ply all as specified on drawing or complete all as specified and directed

S&F in reapirs to 4mm thick one side teak finished plywood of size 780mm x 180mm including 12mm dia half cut teak wood beading of both side of foot board including removal of damaged ply all as specified on drawing or complete all as specified and directed

S&F in repairs to flat iron of mild steel of size 35mm x 5mm, bents to right angle on each corners of Bed Hard all as specified on drawing or complete all as specified and directed

Removal of existing worn out paint including preparation of surface complete of the bed hard steel and M&L for applying two coats of 1st quality synthetic enamel paint of approved colour and make, over a coat of red oxide primer, rest all as shown on drg and complete all as specified and directed

CHAIR DINING /CHAIR DINING PVC / CHAIR DINING CUSHIONED

Recaning of repaired chair dining with best quality of approved plastic cane 2mm wide, 0.4mm thick and border with 3x0.60 mm cane of white or cream ivory all as specified on drawing or complete all as specified and directed

Removing of old unserviceable/damaged existing cushioned Seat from chair providing new seat made of 75mm thick 40 density foam cushion over 12mm thick commercial plywood BWR grade duly covered with best quality tapestry complete all as specified on drawing or as directed by Engineer-in-charge. Sample of tapestry shall be approved by GE.

Removing the existing unserviceable stiffeners and providing new Teak wood 2nd class hard wood stiffeners of size 25x20 mm complete all as specified on drawing or complete all as specified and directed

Removing of existing unserviceable/broken PVC Shoes, M & L for fixing of PVC shoes superior quality of 20mm dia with suitable screw at the bottom of the leg.

Removing of old unserviceable/broken PVC seat from chair dining and S&F new PVC seat 4mm thick in single piece all as per shape and size shown on drawing and complete all as specified and directed

CHAIR VERANDAH

Removal of existing worn out paint and Re-Painting to the entire frame of chair verandah with white colour synthetic enamel paint over a coat of primer of approve make including removing old unserviceable cane/plastic newar from seat & back and recaning the seat & back of complete chair including handles etc with approved 4mm white plastic cane as per Matt Pattern all specified on drawing or complete all as specified and directed

Welding joints of broken leg of 19/20mm MS tube & other joints as per drg

Hard PVC/Nylon shoes as per drg

CHAIR EASY

Recaning of repaired chair easy seat and back of approved quality white or cream ivory with 2mm wide, 0.4mm thick cane and border with 3x0.60 mm cane complete all as specified on drawing or complete all as specified and directed

Removing of existing unserviceable/broken PVC Shoes, M & L for fixing of PVC shoes superior quality of 20mm dia with suitable screw at the bottom of the leg.

PEG TABLE (450MMx300MMx380MM)

Removing of old unserviceable top from peg table and S&F new top made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and complete all as specified and directed

All as per the description of srl item No 6.01 here-in-before but stiffener of Peg table.

Removing of existing unserviceable/broken PVC Shoes, M & L for fixing of PVC shoes superior quality of 20mm dia with suitable screw at the bottom of the leg.

ALMIRAH LARGE/MEDIUM /SMALL STEEL

S&F in repairs legs of Almirah large and providing new leg by welding made out of 1mm MS Sheet into required shape for Almirah large, rest all as shown on drg and complete all as specified and directed

S&F in repairs legs of Almirah Medium/Small steel and providing new by welding made out of 1mm MS Sheet into required shape for almirah, rest all as shown on drg and complete all as specified and directed

S & F in repairs locking device including replacement of brass 6 lever locks iron body with duplicate keys chromium plated to Almirah, rest all as shown on drg and complete all as specified and directed

S&F in repairs handle Chromium plated of size 150 mm grip length with both sides screwed to Almirah steel, rest all as shown on drg and complete all as specified and directed

Repair to existing shelf including welding

Removal of existing worn out paint from inside & outside including preparation of surface complete of the Almirah large steel and M&L for applying two coats of 1st quality synthetic enamel paint of approved colour and make over a coat of red oxide primer, rest all as shown on drg and complete all as specified and directed

All as per the description of srl item No 7.06 here-in-before but Almirah Medium/small steel.

SOFA SET 4/ 5 PERSON WITH CUSHION

Removing the existing unserviceable cushion of sofa set, tapastry cloth and replacing with new foam cushion 40 density 100mm thick of size 558mm x 533mm x 100mm duly covered with new tapastry cloth including mulmul completly stiched, rest all as shown on drg and complete all as specified and directed Note :- (i) Each cushion for seat or back will be measured as single unit. (ii) The tapastry cloth shall be mat finish and shall not less than Rs. 350/- per metre and as approved by GE.

Removing the existing unserviceable tapastry cloth of sofa set and replacing with new tapastry cloth mat finish of size 558mm x 533mm x 100mm with mulmul cloth. Note : tapastry cloth costing not less than Rs. 350/- per metre and as approved by GE.

Removing the existing unserviceable front leg from Sofa and providing new first class teak wood of leg size 70mm x 35 mm x 495mm, rest all as shown on drg and complete all as specified and directed

Removing the existing unserviceable rear leg from Sofa and providing new first class teak wood leg size 70mm x 35 mm x 495mm, rest all as shown on drg and complete all as specified and directed

Removing existing unserviceable Arm rest from Sofa and providing new first class teak wood Arm Rest of size 35mm x 70mm x 725mm, rest all as shown on drg and complete all as specified and directed

Removing existing unserviceable side rail from Sofa and providing new first class teak wood side rail of size 35 mm x 100mm x 585mm, rest all as shown on drg and complete all as specified and directed

Removing existing unserviceable bearer from Sofa and providing new first class teak wood bearer of size 40mm x 40mm x 725mm, rest all as shown on drg and complete all as specified and directed

Removing existing unserviceable battens from Sofa and providing new first class teak wood battens of size 50mm x 20 mm, rest all as shown on drg and complete all as specified and directed

Removing existing unserviceable front rail from Sofa three seater and providing new first class teak wood front rail of size 35mmx 100mm x 1590 mm, rest all as shown on drg and complete all as specified and directed

Removing existing unserviceable front rail from Sofa single seater and providing new first class teak wood front rail of size 35mm x 10mm x 530 mm, rest all as shown on drg and complete all as specified and directed .

TABLE DINING 6 PERSONS

Replacement of existing unserviceable table top for Table dining 6 persons made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and complete all as specified and directed

Replacement of existing unserviceable table top for Table dining 4 persons made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and complete all as specified and directed

Removing of existing unserviceable/broken PVC Shoes, M & L for fixing of PVC shoes superior quality of 25mm dia with suitable screw at the bottom of the leg.

TABLE WITH/ WITHOUT DRAWER/ONE PCS (900x 600 x 760mm)

Removing of existing unserviceable table top for Table with/without drawer /one piece and providing new table top made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and complete all as specified and directed

S&F in repairs to unserviceable damaged bottom stiffners (short side) from Table with/without drawer 900mm x 600mm x 760mm made out of hard wood (Teak) complete, rest all as shown on drg and complete all as specified and directed

Removing of existing unserviceable/broken PVC Shoes, M & L for fixing of PVC shoes superior quality of 25mm dia with suitable screw at the bottom of the leg.

TEAPOY WOODEN

Replacement of existing unserviceable top for Teapoy made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and complete all as specified and directed

S&F in repairs to unserviceable damaged bottom stiffners (both short & long) from teapoy made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

Removing of existing unserviceable/broken PVC Shoes, M & L for fixing of PVC shoes superior quality of 20mm dia with suitable screw at the bottom of the leg.

TABLE CENTRE

Replacement of existing unserviceable table top for Table centre made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and complete all as specified and directed

Removing of existing unserviceable/broken PVC Shoes and M & L for fixing of PVC shoes superior quality of 20mm dia with suitable screw at the bottom of the leg.

Table Bed Side

Removing of existing unserviceable sides of Table Bed Side and providing new sides of 18mm thick prelaminated particle Board with teak wood colour finishing one side and balancing white on the other side of exterior grade and 18mm x 6 mm teak wood beading on front sides, rest all as specified on drawing or complete all as specified and directed. Note:- Each side will be measure as single unit

Removing of existing unserviceable Top and bottom of Table Bed Side and providing new Top of 18mm thick prelaminated particle Board with teak wood colour finishing one side and balancing white on the other side of exterior grade and 18mm x 6 mm teak wood beading on front sides, rest all as shown on drg and complete all as specified and directed . Note:- Each Top & Bottom will be measure as single unit

Removing of existing unserviceable Back of Table Bed Side and providing new Back of 6mm plywood commercial shall be fixed with headless nail, rest all as shown on drg and complete all as specified and directed .

Removing of existing unserviceable shelf of Table Bed Side and providing new shelf of 12mm thick prelaminated particle Board with teak wood colour finishing one side and balancing white on the other side of exterior grade and 12mm x 6mm teak wood beading on front sides, rest all as shown on drg and complete all as specified and directed .

Table Bedside (Map)

Replacement of Upper drawer made of 18mm thick prelaminated particle board,exterior grade and provided with 6mm thick bottom of ISI marked commercial plywood of BWR grade complete all as specified and directed.

Replacement of lower drawer made of 18mm thick teak faced prelaminated particle board provided with 6mm thick bottom of ISI marked commercial ply BWR grade & telescopic channel of best quality as approved & complete all as specified and directed

Removing of old unserviceable top from table bed side and S&F new top of same size made out 18mm thick exterior grade pre-laminated particle board teak faced with 04mm thickteak wood beading all as shown on drawing and complete all as specified and directed .

All as per the description of srl item No 14.01 here-in-before but side of table bed side.

Removing of old unserviceable back ply of table bed side and S&F new back ply of same size made out of 6mm thick commercial plywood complete all as shown on drawing and complete all as specified and directed .

Removing of old/unserviceable handle from the table bed side S&F new CP steel handle 100mm long as per sample, shape and size all as per drawing and complete all as specified and directed .

S&F in repairs new hard rubber shoes to Table bed side all as shown on drawing and complete all as specified and directed .

CHAIR EASY CUSHIONED (TP)

Removing the existing unserviceable tapestry cloth and foam cushion from seat and back of chair easy upholstered completely, replacing with new foam cushion 40 density duly covered with new tapastry cloth including completly stiching, rest all as shown on drg and complete all as specified and directed .

M&L removing of old polish completly by paint remover from chair easy, preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying applying two coat of glossy Melamine polish of approved make over a two coat of melamine sealer finally till the smooth finishing complete rest all as specified on drawing or complete all as specified and directed .

CHAIR COMPUTER : FD/E6/MAP/01

Replacement of old unserviceable seat and back of chair with new seat of 12mm thick plywood commercial quality (ISI marked) covered with 75mm thick U foam and best quality of tapestry cloth. The back shall be 6mm thick plywood commercial quality (ISI marked) fixed on frame with screwes and covered with 40mm thick U foam over shape and tapestry cloth. Fixing shall be all as per drawing and including all minor repairs and wedling etc complete all as specified and as directed. (Note:- Sample of tapestry cloth shall be got approved by GE before incorporation in the work).

Removing of old/unserviceable tapestry cloth from seat and back of existing Chair Computer and replacing with new tapestry cloth to seat and back of Chair Computer complete all as specified and as directed. (Note:- Tapestry cloth shall be of the Price range 150/- to 175/- per Sqm as per Sample got approved from GE before incorporation in the work).

Replacement of unserviceable hydraulic system of Chair Computer for the adjustment of height complete all as specified and directed.

Replacement of old unserviceable/broken wheel base of Chair Computer complete all as specified and directed.

Replacement of old unserviceable / broken arm rest with new arm rest of black integral skin polyurethane reinforced with MS insert and shall be scratch and weather resistant of Chair briefing static base, complete all as specified & directed.

CHAIR WRITING :

Replacement of old unserviceable seat and back of chair with new seat of 12mm thick plywood commercial quality (ISI marked) covered with 75mm thick U foam and best quality of tapestry cloth. The back shall be 6mm thick plywood commercial quality (ISI marked) fixed to frame with screw and covered with 40mm thick U foam over shape and best quality of tapestry cloth. Seat and back fixed on frame with screw and including all minor repairs with welding to steel frame etc complete all as specified and directed. (Note:- Sample of tapestry cloth shall be got approved by GE before incorporation in the work).

Removing of old/unserviceable tapestry cloth from seat and back of existing Chair Writing and replacing with new tapestry cloth to seat and back of Chair Writing complete all as specified and directed . (Note:- Tapestry cloth shall be of the Price range 150/- to 175/- per Sqm as per Sample got approved from GE before incorporation in the work).

Welding to broken joints of Chair writng complete all as specified and directed.

Replacement of old unserviceable / broken arm rest with new arm rest of black integral skin polyurethane reinforced with MS insert and shall be scratch and weather resistant of Chair briefing static base complete all as specified and directed.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polish over a coat of mension wax polish till the smooth finishing complete all as specified on drawing or complete all as specified and directed for the following furniture articles:-

Bed plywood top

Chair dining/Chair dining PVC /Chair dining Cushioned

Chair Easy

Peg Table

SOFA SET 3 pcs 5 Seater

Sofa Set 4 Seater

Table dining 6/4 persons

Table with/without drawer (900mm x 600mm x 760mm) /Table one Pieces

Teapoy wooden

Table Bed Side

Table centre

Schedule of Credit - Total contract sum shall be calculated after deduction of Sch of Credit amount Credit amount - 48,350.00

SMS Enterprises