SPECIAL REPAIRS TO SHED NO. A/8/12 AT PANAGARH MIL STN UNDER GE (P) PANAGARH

Amount

SCHEDULE 'A' PART-I

Dismantling of plain or corrugated steel sheeting any gauge thickness ,flat or curved including ridges,hips, valleys,etc as in roof covering including dismantling of wind tie, complete all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

S&F pre-painted galvalum aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall ridge, fixed with self tapping screws complete all as specified and as directed.

S&F plain, galvanized 1 mm thick, mild steel sheeting, in ridges,hips, vally gutter, drips and straight flashing, ( length and girth as fixed) with grade of zinc coating 275, completed all as specified and as directed.

S&F 2mm thick corrugated fiber glass reinforced translucent sheet with two corrugated side lap fixed with two coach screw and washer in roof etc, complete all as specified and as directed.

Re-fixing of old CGI sheet 0.63mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as direted by Engr-in-Charge. Note : Old CGI Sheet reused in this item is obtain from Item No. 1.01.

Dismantling of structural steel work including door gates but excluding framed truss, complete all as specified and as directed.

S&F MS Rolled section FE 410-W(gde E-250) as in main and cross beam , hips and jack rafter,purlins where connected to common rafters and running rails and guide for doors,fixed with angle cleats or other connecting plate, complete all as specified and as directed.

All as per item No. 1.08 here in before but erection and fixing only , complete all as specified and as directed Note : Material obtained from dismantling refer item No-07 here-in-before shall be re-used.

S&F FE 410-W(gde E-250) as framed work as in door or gate of angle or other section with gusset plate, rail, braces,etc complete drilled for fixing of steel sheeting or other covering ,door etc to be prepared for hanging or sliding with and including either hooks or hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing , complete all as specified and as directed.

All as per item no. 1.10 here in before but erection and fixing only complete all as specified and as directed. Note : Material obtained from dismantling refer item No. 1.07 here-in-before shall be re-used.

S&F bands ,straps or stays for rain water ventilating pipe ,incl bolts if required, hooks for large gates, hook and pintle hinge, hand made sliding bolt ,clamp, wall tie ,plate washer and similar articles confirming to FE 290,GDE E-165 ,complete all as specified and as directed.

M&L for prepretion of old painted steel surfaces of any description,over 10 cm in width or girth,not otherwise described and applying two coat of aluminium paint over priming with aluminium red oxide, complete all as specified and as directed.

M&L for prepration of new steel surfaces of any description,over 10 cm in width or girth,not otherwise described and applying two coat of synthetic enamel paint over priming with red lead , complete all as specified and as directed.

M&L for prepretion of old painted steel surfaces of any description n.exc 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over priming with red lead, complete all as specified and as directed.

M&L for prepretion of new steel surfaces of any description n.exc 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over priming with red lead, complete all as specified and as directed.

Taking down and Refixing of shutter in other opening of any description exc 2.0 sqm each, complete all as specified and as directed.

S&F for framed brackets of angles or tees with web and flange cut to shape ,drilled and counter sunk for screws ,including bending and welding angles as necessary ,riveting n exc 10 kg each bracket conforming to Fe-290 gde E-165 , complete all as specified and as directed. Note : Brackets over 10 Kg each to be measured under structural steel.

S&F steel ventilator/window with top hung shutter incl hinge steel peg stay, complete all as specified and as directed.

S&F 3 mm thick glass ordinary quality and glazing with oil putty in square n. exc 0.50 sqm in each pane,complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness (below or above ground level ) incl spreading and removing of rubbish, complete all specified and as directed.

M&L for cement concrete type B2 1:2:4 using 40 mm graded stone aggregate in foundation filling and mass concrete using metalic hardner @ 5 Kg/Sqm, complete all as specified and as directed.

Supply only metalic floor hardner, complete all as specified and as directed.

M&L for forming 20 mm thick expansion joint including smooth saw cutting the joints with diamond blades after 48 hrs of fresh poured concrete, clean the surface and fill the joints with pre-formed bitumeneous filler and top 30 mm primed and sealed with sealing compound Grade B ,complete all as specified and as directed. Note : Thickness of slab 150 mm.

M&L for forming contraction dummy joint 65mm deep x 10 mm wide including smooth saw cutting the joints with diamond blades after 48 hrs of fresh poured concrete, clean the surface and filled with sealing compound Gade B, complete all as specified and as directed.

M&L for forming construction joint 30mm deep x 10 mm wide including smooth saw cutting the joints with diamond blades after 48 hrs of fresh poured concrete, clean the surface and filled with sealing compound Gade B, complete all as specified and as directed.

Demolition of PCC block masonay built in cement mortar or cement lime mortar including all work areas etc and stacking serviceable materials separate, complete all as specified and as directed.

M&L for brickwork with old size Fly ash brick straight or curved on plan exc 6m mean radius built in CM 1:6 , complete all as specified and as directed.

M&l for 15 mm thick rendering in cm 1:6 on fair faces of brick work or concrete wall surfaces finished even and smooth (without using extra cement), complete all as specified and as directed.

M&L for preparing surfaces plastered or unplastered wall and applying two coats of cement base paint over a coat of primer ,complete all as specified and as directed.

Removal of debrish/rubbish after demolition of masonry work from site at a distance 500 mtr to 1 km , complete all as specified and as directed by Engr-in-Charge.

Taking down frame with shutters, window boards etc. not exc 1.5 sqm each (Without taking off shutters from the frames) and removing, complete all as specified and as directed.

SCHEDULE 'A' PART-II

Taking down carefully aluminum/copper point wiring (light/fan/socket/power) including fittings such as switches, socket ceiling roses, pendants, regulators etc and removing unserviceable materials from site and making good disturbed surfaces of walls/floors and reuse the serviceable fittings under respective items, complete all as specified and as directed.

M&L for point wiring with 1.5 Sqmm (Nominal area) PVC insulated and unsheathed single core cable 1100 volts grade with standard coper conductor in and including PVC surface conduit including accessories along with continuous earth wire 1.0 Sqmm PVC insulated, unsheathed stranded copper conductor cable and connected to common earth dolly with and including 1.6mm thick cadmium plated sunk MS pressed steel terminal boxes with 3.0mm thick hylam sheet cover fixed with brass screw complete with all accessories for on light point/ Fan point controlled by one, 1-Way switch, complete all as specified and as directed.

All as per Item No. 2.01 mentioned here-in- before but one 5 pin 5 Amps socket out let on the same board with other switches with 1.5 sq mm PVC insulated copper conductor for continuous earthing, complete all as specified and as directed.

All as per item No. 2.01 mentioned here-in- before but one 5 pin 5 Amps socket out let on independent board with 1.5 sq mm PVC insulated copper conductor for continuous earthing, complete all as specified and as directed.

All as per item No. 2.01 mentioned here-in- before but 6 pin15 Amps socket outlet on independent board with 4 sq mm PVC insulated and sheathed copper conductor with 4 sq mm PVC insulated copper conductor single core for continuous earthing ,complete all as specified and as directed.

M&L for Switch piano flush type single pole one way 6 Amp, complete all as specified and as directed.

M&L for Socket outlet 2 in 1, 3 pin , 6 Amps flush type ,complete all as specified and as directed.

M&L for Switch 16 Amps flush type universal,complete all as specified and as directed.

M&L for socket outlet 5 in 1, 3 pin, 6 Amp and 16 Amps flush type universal ,complete all as specified and as directed.

M&L for ceiling rose, PVC/Polycarbonate three terminals, complete all as specified and as directed.

S&F Metal exhaut fan 300 mm, 230, AC, 50 Hz complete with fixing arrangement and connection, complete all as specified and as directed.

S&F 01x 18W LED fittings decorative Regal batten for LED tube with tube 18 watt lighting fixture with extruded polycarbonate complete with all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing, complete all as specified and as directed. Make : Havells/Bajaj/CG

S&F fan Wall mounted 400 mm, 230, AC, 50 Hz complete with fixing arrangement and connection ,complete all as specified and as directed.

Supply and fix submain wiring with 2 x 2.5 Sqmm FR PVC insulated copper cable 1100 volts grade multistranded, unsheathed conductor drawn in rigid steel conduit including 2.5 Sqmm multi stranded FR PVC insulated copper wire for earth continuity conductor connected to common earth dolly for connections to control gear of hanger light ,complete all as specified and as directed. NOTE : (i) Suitable ladder/staging for doing work at a height of 6-8 mtr, inside the hanger, to be provided by the contractor at his own arrangement and cost. (ii) Rigid steel conduit with all acessories will be measured and paid separately.

Supply and fix non metallic PVC conduit, outer dia 25mm, with all acessories i.e, Tees, Elbows, Junction Boxes, etc. complete all as speciified and as directed.

S&F 140 watt LED Highbay Luminarie with secondary optics made in pressure die cast housing and heat sink in aluminium extrusion with IP-66 of 140 W LED fitting, including hook for hanging of light, complete all as specified and as directed. Make : C.G(Cat No- LHB11-140-CDL/60)/Philips/Bajaj

M&L sheet metal enclosure for DBs TPN 4 way double door type with 200amps, IP 43 rated busbar , including necessary connection, complete all as specified and as directed.

M&L for MCB single pole 6 to 32 Amps 240 V 50 Hz 10kA 'C' series, complete all as specified and as directed.

M&L for MCB TPN 63 Amps 240 V 50 Hz 10kA "C" series, complete all as specified and as directed.

M&L earthing complete with galvanised earth plate electrode 600 x 600 x 6 mm thick burried directly in ground ( earth pit not less than 2.25 m deep below normal ground level ) with top edge of the plate not less than 1.5 meter below normal ground level, the earth plate surrounded by a mixture of charcoal dust and salt to a packed thickness of 150 mm on all sides with and including necessary exacavation earth work returning, filling in and removal of surplus soil upto 50 mtr including GI wire 4 mm dia bolted and revetted to earth plate at one end in and connected to continuous GI earth wire encased in and including 15 mm GI light grade pipe with all fittings from top edge of earth plate, complete as specified and as shown in electrical plate no 5.

Supply and fixed in repair's street light bracket made out of GI pipe light grade 25 mm dia 1.5 mtr long bent to required shape as directed and fixed to pole complete with painting and including two set of 20x3mm FI clamps and fixing arrangement such as nuts, bolts and washers ,complete all as specified and as directed.

Supply and fixed building security light fittings 25 watts, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size, complete all as specified and as directed. Make: HAVELLS (Cat no. ENDURKPEEARLSL25WLED757SASYTOPC) / BAJAJ / C.G)

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, pipes etc. and getting out including trimming the sides and forming bottom surfaces to required levels in soft/loose soil ,complete all as specified and as directed.

Returning, filling in, including spreading, levelling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil ,complete all as specified and as directed.

Removing excavated material (soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as specified and as directed.

Material and labour for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete as specified and as directed . Note :- Punned thickness 18 cm shall only be considered for payment

M&L for laying well fly ash brick size having compressive strength 75Kg/sqcm, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection , complete all as specified and as directed.

Supply, laying and testing of cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 1100 Volts grade, cross sectional area 25 Sqmm 4 core ,complete all as specified and as directed by Engr-in Charge.

Schedule of Credit

UNIVERSAL TRADING

Anmol Yash S.D. Construction Pvt. Ltd.

Hooghly Construction Co.

M/S AJIT KUMAR KONAR AND SUBHAS CHANDRA KONAR

BABY ENGINEERING ELECTRICAL MECHANICAL STORES