REPAIR/MAINT TO CERTAIN B/R WORKS FOR CENTRAL INSTITUTE UNDER AGE B/R-I UNDER GE (EAST) AGRA

Amount

Demolition of cement concrete (unreinforced) in any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for providing PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in coping, bands, plinth course and junction of brick edging and brick lining for drains as in benching other similar works including use and wast of necessary form work complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 complete all as specified & directed

M&L for brick work (except brick) straight or curved on plan exc 6 M mean radius, built in CM 1:6 complete all as specified & directed but except brick. Note:- Old bricks shall be obtained from item No 03 shall be reused after cleaning. Rate for cleaning of old bricks shall be included with quoted rate.

Taking down cement or cement lime plaster of any discription on brick or stone walls/ ceilings etc, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarsesand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement persquare metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size)in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings over a coat of acrylic polymer (Paymentforproviding grooves shall be made separately), complete all as specified and directed.

M&L for 15mm thick SmartCare ready mix plasterfor External surface is a specially designed ready to use cement based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering on bricks, block, stone walls over a coat of acrylic polymer as well as concrete surfaces. complete all as specified and directed.

M&L for two coat water based premium acrylic smooth exterior paint apex ultima or equalent emulsion of approved Colour with silicon additive & Colour stay Technology. Excellent Dit Pick up resistance With low VOC less than 50 gram/ lite as per the LEEDS specifications, Anti Algal Properties in two coats @ 1.79 Itr (undiluted)/ 10 sqm diluted with water as per Manufacturer instructions applied over priming coat with fully automatic airless spray machine of paint application with a flow speed of min 1 Ir per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in both the coats of paint complete all as directed. Note:- (a.) The work pertaining to periodical services & Water Proofing shall be executed from authorized applicator through manufacturer of which the materials i.e. Paint, Distemper, Putty etc. is proposed to be used by the contractor and approved by Garrison Engineer. (b) Masking of window/doors during spray painting using polythene film will be included. (c) Rate quotated includes work at any height (not.exc 10 mtr) incl necessary scaffolding /Centreing etc and cleaning the waste materials and debris from out of MoD land as directed and complete.

M&L for 10 mm thick SmartCare ready mix plasterfor Internal surface is a specially designed ready to use cement based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering on bricks, block, stone walls over a coat of single component polymer as well as concrete surfaces. complete all as specified and directed.

M&L for applying two coats of oil bound distemper with roller on new decorated wall surfaces over 1 mm thick white putty including complete removal of existing treatment with mechanical complete all as specified and directed.

M&L for applying two coats of texture paint that adds a decorative, three-dimensional surface with a unique visual and tactile appeal, unlike smooth flat paintsr with roller on new decorated wall surfaces over 3 mm thick white putty,and abase coat including complete removal of existing treatment with mechanical complete all as specified and directed.

M&L for applying one coat of oil emulsion distemper with roller on old decorated wall surfaces including complete removal of existing treatment with mechanical complete all as specified and directed.

M & L cutting holes into or through brick wall built in cement mortar superfacial area not exc 150 Sqcm and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

S&F 5.0 cm thick sand stone slabs in sun shades, chajjas, shelves, roof slabs etc n.exc. 2m in length punched dressed on face and along exposed edges, self faced on other side and set and pointed in CM 1:4 complete all as specified and directed.

Dismantling cast iron work/mild steel work of any description complete all as specified and directed.

S&F mild steel joist channel angle or tee sections fixed independently with out connecting plates etcof grade Fe-410-W (Gde E-250 quality B) complete all as specified and directed..

M&L for two coats of synthetic enamel paint over a coat of red oxide primer incl preparation of New steel surface complete.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surfaces of size 350 x 250x 7mm /450mm x 350mm x7mm thick set and jointed in neat cement slurry over 10 mm thick rendering in CM 1:4 for receiving the tiles complete all as specified complete all as specified.

M&L Non Skid ceramic coloured tiles 7mm to 8mm thick, area of each tile exc 0.11 Sqm but n. exc 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10 mm thick cement mortar (1:6) screed bed for floor finishes complete all as specified complete all as specified.

M&L Virified Ceramic tiles light /dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and directed.

Dismantling wall and ceiling boards( fibre pulp, insulation etc.) or insulation board /slabs/blanket any thickness including cover fillets.

S&F false ceiling at all heights with PVC solid pannel to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge.

S & F PVC wall lining consisting of 8-10 mm thick wooden grain printed PVC sheet inclusive of solvent cement and fixing channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, at site on wall/ceiling as per specification and complete all as specified and directed.

M&L PCC 1:3:6 C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection ( 75 mm thick ) laying in alternate ways finished even and smooth without using extra cement all as specified.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings in roof cobvering complete all as specified and directed.

S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet AZ - 150 thickness of sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet AZ - 150 thickness of sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F in repairs 15 mm bore chromium plated fancy bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed.

S & F factory made uPVC white colour three track three panels sliding window with fly proof SS wire mesh(Two nos glazed & one no wire mesh panels) up to 1.50m height made of (big series) frame 116 x 45mm & sash 46 x 62mm both having wall thickness of 2.3 (+ or -) 2mm and single glazing bead/double glazing beads of appropriate dimension. (area of window above 1.75Sqm ) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profile duly reinforced with 1.60 thick galvanised mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing bead sand uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated ) touch locks with hook, zinc allo body with single nylon rollers (weightbearing capacity to be 40 Kg) , GI fastener 100 x 8mm size for fixing frame to finished wall and necessary stainless steel screws, etc. profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fiximg hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and incl 4mm thick cooling glass and stainless steel wire mesh of approved quality complete all as specified and directed.

S&F in repairs 10 ltrs capacity PVC flushing cistern low level (white) with inlet ball valve and handle including flush pipe, brackets, rubber bush, washers etc complete all as specified and directed.

S&F in repair 15 mm bore CP Stop valve / angle valve screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed.

S & F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends with access door of any radius complete all as specified & directed.

Taking up or down 15mm bore steel tubing and connection complete all as specified and directed.

All as per item No 37 above but 20mm bore complete all as specified and directed.

Supplying and laying 25 mm outer diameter of CPVC pipes SDR 11 including CPVC Brass fittings (Brass elbow, Brass Tee, MTBA, FTBA etc), Unions, Ball valves, Flange and tank adaptor or necessary fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying 20 mm outer diameter of CPVC pipes SDR 11 including CPVC Brass fittings (Brass elbow, Brass Tee, MTBA, FTBA etc), Unions, Ball valves, Flange and tank adaptor or necessary fittings on walls/ceiling or laying in floors complete all as specified.

Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth etc brick wall complete all as specified and directed.

S&F in repairs 1000 ltr capacity rotational moulded polyethylene water storage tanks with cover (cylindrical vertical with closed top) hoisted and fixed in position including fittings all as specified in SSR Part I .

S&F 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts, 600 mm long complete all as specified and directed

S & F of single seat plastic WC seat cover and mild steel chromium plated or aluminised hinging device as in repairs etc complete all as specified and directed

S & F in repairs Flushing jet for pedestal pattern WC incl .flexible pipe and brass chromium plated nuts and bolts and water pipe of size 1150 mm long between dia & fixed completed all as specified and directed.

S&F in repairs CP Central hole basin mixture screwed for 15 mm dia pipes including PVC connection etc complete etc complete all as specified and directed

S&F in repair 15mm bore, brass chromium plated pillar cock (foam flow) two ways screwed down for pipe and fixed complete all as specified and directed.

S&F in repair Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm- 45gms/40mm-60 gms) of 32mm bore suitable for wash hand basin complete all as specified and directed.

S&F 32 mm dia PVC waste pipe for wash basin /sinks with cupling complete all as specified and directed.

S&F in repair 150 mm square grade of 304 stainless steel grating with openable flap (Min weight 100 gms) complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.50mm thick sheet glass 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and directed.

S&F facoty made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC , ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for to rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to getter with solvent cement, supplying & fixing in the frame at site as per specification.

S & F Solid PVC door frame for PVC doors, Kitchen cabinet of size 50mm x 47mm made out of 5mm PVC sheet reinforced with MS square tube, as shown on drawings as per manufacturers specification complete all as specified and directed.

S & F PVC door( back side) stopper 75mm long complete all as specified and directed.

S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 100 mm long medium weight, cold rolled mild steel Butt hinges complete all as specified and directed.

S&F 150 mm long aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repair brass floor door stoppers double legged length 140mm with hard drawn steel spring fitted in floor complete all as specified and as directed.

S&F in repair 150 mm long Extruded brass handles designer type, fabricated type polished complete all as specified and as directed.

S&F in repair 100 mm long Extruded brass handles designer type, fabricated type polished complete all as specified and as directed.

S&F in repair 75 mm long Extruded brass handles designer type, fabricated type polished complete all as specified and as directed.

S&F in repair 150mm size Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and as directed.

M&L in repair for 250mm long Brass, sliding door bolt withsand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and as directed.

S&F in repair 25 mm stainless steel curtain rod complete all as specified and directed by Engr-in-charge.

S&F SS heavy duty decorative brackets suitable for 25mm dia curtain rod (minimum projection from wall 75mm) fixed in wall including drilling, rawl plug, screws etc complete all as specified and directed. Note: Curtain rod shall be measured and paid separately

S & F Brass magnet catcher suitable for CB/cabinet shutter complete all as specified and directed.

S & F Anodised aluminium ventilator frame/shutters powder coated, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

S & F Stainless steel wire cloth, 0.71 mm nominal dia of wire fixed with tinned tacks, of 20mm mesh of stainless steel wire staples complete all as specified and directed

M&L Varoda green marble makrana Adanga stone 18 to 20 mm thick in steps, pillars, wndow cills, pillars, window cills, cooking platforms and like laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

S&F 5.0 mm thick Figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sq. M in each pane complete all as specified and directed.

S & F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

M & L (Brushbond RFX) Elastomeric polymer modiffied cemtentitious waterproofing coating used for waterproofing of extg and new naked bricks surface complete all as specified and directed.

M&L for providing pre-cast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in cover (for manholes and drains) including necessary form work set in CM 1:6 with and including demolition complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately)

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with cli complete all as specified and directed.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

M&L for factory made Pressed steel frames 105 x 60 x 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock, strike plate etc complete including PCC (1:3:6) type C-0 (using 12.5 mm graded stone aggregate) as in filling hollow portion of frame complete all as specified and directed.

S&F Factory made flush shutter 35 mm thick solid core construction with block board core and plywood face panels commercial type complete including aii fittings and fixture all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer on wooden surface over 10 cm width or girth including preparation of new or previously untreated wood surfaces complete all as specified and directed.

M& L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along the internal/external wall and wooden Cup board,shelves,etc.wooden area should drill by 6 mm bit,Gap between two holes is 30 cm to 45 cm internal/external wall skirting level should drill by 8/10/12 mm bit,gap between two holes is 45 cm to 60 cm.filling the holes by 100 ml to 150 ml dilution of chemical emulsion in two stages 3 stage close the holes by white cement and finsihes with existing surfaces.The ATT chemical should be odorless and mixed formulation should be injected at the rate of 5 ltr per sqm. The ATT chemical should contains. (i) Byfinthrin 20 % EC(Smell Chemical) (ii) CHLORPYRIPHOS 20 % EC (Smell Chemical) (iii) Imidacloprid 30.5 % SC (Odor less Chemical)

S&F in repair vitreous china Wash Basin counter Top 600x400x185mm including stainless steel bottle trap and 40 mm dia GI pipe up to Floor trap complete all as specified and directed.

S&F vitreous china rimless single piece WC of Size: 380x700x665 mm, Single Piece WC with PP Soft Seat cover, Hinges, fixing accessories, accessories set, and cistern fittings, P trap-180mm complete all as specified and directed.

S&F in repair Health Faucet (ABS Body) with 1.20 M Long PVC Tube and wall Hook screwed down to GI pipe or union/angle valve complete all as specified and directed.

S&F in repair Towel Rack with Lower Hanger (Stainless Steel) with hook complete all as specified and directed.

S & F in repair for 15 mm bore, fancy type, Wall Mixer 3-in-1 System with Provision for both Hand Shower and Overhead Shower Complete with 115mm Long Bend Pipe, Connecting Legs & Wall Flange and including Telephone Shower and shower stand complete all as specified and as directed.

S&F in repair 15mm dia brass chromium plated Single Lever Sink Mixer With Swinging Spout on Upper Side (Wall Mounted Model) With Connecting Legs & Wall Flanges for mixing hot and cold water, screwed down for 15 mm dia bore GI Pipe complete all as specified and directed.

Material and labour for water proofing treatment to sunken slab, walls, etc, and shall be carried out as specified below and as directed:- (a) Demolition of Cement concrete/brick bats filled on sunken slab upto mother slab including removing and Clean the sunken portion of toilet / Baths/ WCs/ Kitchen thoroughly to remove laitance, dirt, dust etc. (b) Brushing cement slurry with 1.2 kg of cement per square metre duly blended with & including water proofing compound. (c) 15 mm thick (Average thickness) plaster in cement mortar (1:4) mixed and applying one coat each of Nitoproof 100 priming coat @1Ltr/5Sqm, after the priming coat applying Nitoproof 120 on plastered surfaces @1Ltr/2.5Sqm with water proofing compound on sunken surface including walls and floors. The corner of sunken portion shall be rounded in concave shape and adequate slope shall be made during plastering to accommodate sump pipe and curing the sunken portion with water minimum for 48 Hrs by ponding. (d) Applying self adhesive type APP based polymeric membrane minimum weighing not less than 3.6 kg/ Sqm and minimum 3 mm thick reinforced with polyester non-woven fabric (weight not less than 150 gm/Sqm) (e) M&L for PCC 1:7:12 type F2 using brick course agreegates for filling of sunken portion after conceling all menbrane upto FFL and sealing all joints to the entire satisfaction of Engineer-in-Charge.

M&L for 5mm thick ceiling plaster on concrete surfaces in CM 1:3 finished even and smooth with a thin layer of sagol complete all as specified and directed.

Dismantling of boarding any description fixed in any position with nails complete all as specified and as directed

S&F factory made 100 % solid wood plastic composite (WPC) flush type shutter of 18mm thickness one side laminate consisting of panel of PVC profile of 18mm (+ 0.7mm) thick of denisity 600 kg per cum manufactured by ISO-9000 certified company using for shutter cillicia ply 18mm thick and fixed with frame. The thickness of shutter is edges painted by matching colour of PVC lining of plain/prelim coloured PVC sheet using etc complete as per manufacture specification.

S&F auto closing hinges 35 mm of 0 crank( KH-001) OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified and directed.

S&F ball bearing runners 45 mm Telescopic channel (KTS-20) full extension load capacity 50 kgs, complete all as specified and directed.

S&F chrome plated stainless steel wire basket (storage basket) pull out type for large utensils, size 480 x 500 x 150 mm of Grade 304 with necessary fixing clips etc. complete all as specified and directed.

S&F chrome plated stainless steel wire basket (cup and saucer basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc.complete all as specified and directed.

S&F chrome plated stainless steel wire basket (plate basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc. complete all as specified and directed.

S&F chrome plated stainless steel wire basket (cutlery basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc. complete all as specified and directed.

S&F chrome plated stainless steel wire basket (Grain Trolley) pull out type, size 480 x 500 x 200 mm Grade 304 with necessary sliding frame structure, fixing clips etc.complete all as specified and directed.

Supply chrome plated stainless steel wire basket (Bottle pull out) pull out type two self, size 120 x 500 x 432 mm with necessary sliding frame structure, fixing clips etc. complete all as specified and directed.

S&F width of flaps (When open) in 40 mm continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and directed.

S & F powder coated aluminium sections for doors, windows, partition including fabrication of frame and shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc. including all accessories such as glazings clips, provn of AC opening and rubber beadings for fixing glass panes in frame complete all as specified and directed. Note : (i) Glass panes/wire cloth will be measured & paid separately . (ii) The quoted rate shall be inclusive of cost of rubber beading and glazing clips,hinges, handle. However it will be not be weighed and not paid separately. (iii) All other minor details including cost of locking arrangement shall be included in the quoted rate.

S&F of power coated any colour anodised aluminium door shutter, aluminium section weighting 0.55 kg/m incl 5 mm thick glass and necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed.

S&F in repair for powder coated aluminium ventilator shutters with frame not less than 0.55 Kg/Rm, half bottom portion fixed with 4mm thick glass with fixed type shutter and top half portion lower type with 4mm thick glass and outer side fixed with stainless steel wire mesh, shutters aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, necessary aluminium fittings etc complete all as specified and directed.

S & F powder coated anodised aluminium three track sliding window made of extruded profiles with reqd size of aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings and plain glass on two shutters and stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples on one shutters with two nylon roller on each shutters including star lock handle complete all as specified and directed.

S & F dholpur stone 16-18mm cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 sqm area and not exceeding 0.5 sqm fixed with and including one number SS clamps (grade -202) of flat 30mm X 2mm, 150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment at Height of up to 11 Mtr complete all as specified and directed.

Taking down of old roof treatment of any description including mud phushka, concrete padding,tiles,cement plaster from roof surfaces etc including cleaning ,brushing and watering to joints and grooves and throwing the demolition materials/waste, debris away from the MOD Land etc complete and the roof of height n.ecx 11 mtr etc complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in roof kerbs, paddings, mud stops slightly chamfered or rounded in edges including required grove cutting complete all as specified and directed.

M&L for Apply one coat of Cipoxy 16D primer in the ratio 1:1 spreading at the rate of 0.200 kg-0.250 kg /sqm in complete dry condition where moisture contain below 7% (should be checked with moisture meter)Allow the primer coat to dry for 6 to 8 hours. Apply 1st coat of Roofseal Classic without dilution spreading at the rate of 0.70/litre/Sq.mt/Coat until all surface is covered. Lay a 45 GSM Fibre glass mesh as a reinforcing material which is incorporated in the coating when the first coat is still in wet condition. Allow the first coat to dry for approximately 4 to 6 hours. Apply the second of chemical with the same application coverage, but in a direction perpendicular to that of the first and second coats. Allow each coat to air cure for a minimum of 4-6 hours after application. Check to see no void surface is left untreated / uncoated.Allow the system to air cure for 7 days minimum etc complete all as specified & directed. Note : The contractor shall submit a gaurantee of 10 years from date of completion of work for waterproofing treatment alongwith manufacturers gauruntee. Contractor have to submit the FDR in the favour of GE (East) Agra before submitting the final bill @ 2.5 % of amount of this item.

JWALA ELECTRIC CONTRACTORS (BID ID -3466551)

M/S SHARADA ASOCIATE (BID ID -3466916)

m/s shanti consruction co (BID ID -3466964)