Loading
Loading…
Loading…
| # | Company | Quoted % | Amount | Rank | Status |
|---|---|---|---|---|---|
| 1 | L1₹3.6 LAdmitted-Finance | +9.99% | ₹3.6 L | L1 | Admitted-Finance |
| 2 | Rejected-Technical | - | - | - | Rejected-Technical technically disqualified |
Tender Value
₹6 L
EMD Value
₹12,000
Closing Date
16 Feb 2026, 1:00 pmClosed
Executive Engineer
PHED CEMPUS NH 68, SANCHORE
Annul Rate Contract of repair, rewinding of mono Block pump set and Repair of Starter complete under Sub division III
2026_PHCJO_536890_1
NIT No. 14/2025-26 Item 22
Open Tender
Repair and Maintenance Works
365 days
PHED Div.Sanchore
As Par Tender Document
3 documents required · 3 mandatory
₹500
MD RISL
₹12,000
Yes
18 Feb 2026
9 Feb 2026
17 Feb 2026
9 Feb 2026
16 Feb 2026
9 Feb 2026
Part "A" Rewinding of three phase squirrel cage induction motor of Monoblock pump sets including all necessary material and of the same characteristics as original with required size of super enameled copper wire (including cost of copper wire),'E' class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including transportation of motor pump to and from Site/ Div/AEn/JEn store complete as per direction of engineer in charge.3 H.P.
SUPPLY & FIXING OF SPARE PARTS FOR MONOBLOCK PUMPSET (MOTOR + PUMP)Connection Plates up to 10 HP
10 HP to 20 HP
Cooling Fan up to 10 HP
10 HP to 20 HP
GM/SS bush Upto 10 HP
10 HP to 20 HP
Mechanical reconditioning of Bearing sheet Upto 10 HP
10 HP to 20 HP
Mechanical reconditioning ofImpeller sheet and Key way slot Upto 10 HP
10 HP to 20 HP
Oil seal Upto 10 HP
10 HP to 20 HP
Labour charge for opening and fitting of pump sets Upto 10 HP
10 HP to 20 HP
Rewinding of three phase squirrel cage induction motor of HSC pump sets including all necessary material and of the same characteristics as original with required size of super enamelled copper wire (including cost of copper wire) 'E' class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including making electric connection at site of installation of motor with starter, alignment with pump sets and transportation to and fro from installation site complete as per direction of engineer in charge at site.Above 15.00 HP but upto 17.50 HP
Above 17.50 HP but upto 20.00 HP
Above 20.00 HP but upto 25.00 HP
Above 25.00 HP but upto 30.00 HP
Above 30.00 HP but upto 35.00 HP
Above 35.00 HP but upto 40.00 HP
Above 40.00 HP but upto 45.00 HP
Above 45.00 HP but upto 50.00 HP
Above 50.00 HP but upto 60.00 HP
Above 60.00 HP but upto 75.00 HP
Above 75.00 HP but upto 100.00 HP
SUPPLY & FIXING OF SPARE PARTS HSC PUMP SETS (MOTOR + PUMP) Connection Plates 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
Cooling Fan 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
Fan Cover 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
G.M./SS Gland Guide Bush 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
Shaft with Sleeve Chuck Nut 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 275 HP
Shaft Chuck Nut 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 275 HP
G.M. Neck Ring 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
Bush Shaft Sleeve of G.M. 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
G.M. Gland Cover 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
S.S. Shaft (Non Magnetic) 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
G.M. Shaft Sleeve Check Nut 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
M.S. Shaft Check Nut 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
Cooling pipe set with nozzle & Nut 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
AIR Cock 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
JOB WORK FOR REPAIR OF PUMP MOTOR Bearing Housing (rebuilding, turning & finishing) 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
Bearing Cap (rebuilding, turning & finishing) 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
Impeller Reconditioning for all type of Pump 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
Labour Charges for Dismantling & Assembling of Pump 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
Coupling with stud and rubber bush 5 HP to 20 HP
20 HP to 30 HP
30 HP to 50 HP
Above 50 HP to 100 HP
Supply & Fixing of tyre coupling sets according to relevant IS code in Centrifugal couple pump sets of approved make Unit. This job also included re-alignment of centrifugal couple pump set after fixing of tyre coupling set as per directed by Engineer-in charge. Type 14 Nos. set
Type 15 Nos. set
Type 16 Nos. set
Type 17 Nos. set
Supply and fixing Ball bearing of Various size for centrifugal/monoblock pump set of ISI Mark as per specification and approved make by EIC. 6304 or equivalent size
6305 or equivalent size
6306 or equivalent size
6307 or equivalent size
6308 or equivalent size
6309 or equivalent size
6310 or equivalent size
6311 or equivalent size
6312 or equivalent size
6316 or equivalent size
6317 or equivalent size
6318 or equivalent size
6319 or equivalent size
NU319C or equivalent size
Suuplying of super enamal copper wire suitable for rewindind of induction motor (only procured for motor rewinding)
Preventive Maintenance Routine maintenance of centrifugal coupled pump and motor including opening, cleaning, greasing and refitting / changing of ball bearing if required, gland refilling and replacing all rusted studs, replacing rubber bushes & coupling nut & bolts for coupling pulley, tightening all nut & bolts of foundation, baseplate, pump & motor etc. Checking & correcting alignment of pump & motor including necessary materials i.e. grease, nut & bolts, studs, washers, gland packing and rubber bushes etc. work done at site complete job 5 HP to 20 HP
20 HP to 30 HP
Above 30 HP and up to 50 HP
Above 50 HP and up to 100 HP
Cleaning of pump house by air blower/ vacuum cleaner or other means including removing of JALA from ceiling and walls etc. complete Job.
Cleaning of Electric Panel PMCC by air blower/vacuum cleaner or other means including tightening of loose connections etc. complete job.
Replacing of damaged/broken gland packing plate with new gland packing plate suitable for centrifugal pump shafts and nut&bolts etc. complete job. 5 HP to 20 HP
Above 20 HP and up to 30 HP
Above 30 HP and up to 50 HP
Above 50 HP and up to 100 HP
PART B SCHEDULE OF STARTER REPAIRING Labour charges for removing electric fault in wiring / making connection through lugs (with the help of cramping tool) of motor pump set with starter at headworks of water supply scheme/Tubewell/ openwell including cost of insulation tape etc..
Labour charges for replacement of defective ampere meter / volt meter with new one on existing panel board in pump house./Tubewell /openwell (new voltmeter/ampere meter will be provided by department
Labour charges for repairing of starter at site including opening and reassembling of starter with labour charges for replacing of defective parts with new one at site.(Parts will be supplied by Depatment)5 to 15 HP.
Labour charges for repairing of soft starter at site including opening and reassembling of starter with labour charges for replacing of defective parts with new one at site.(Parts will be supplied by Depatment)5 to 15 HP.
Supply & filling starter oil in oil immersed starters at site.
Please Enable Macros to View BoQ information
stage.html
html • 0.03 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 2.52 MB
TDItem22.pdf
Tender Documents • 0.83 MB
BOQ_956792.xls
BOQ • 0.42 MB
Download all tender documents and submit your bid