SPECIAL REPAIR OF TRANSPORTATION SECTION AT HANGAR NO.12 AT AFS CHAKERI KANPUR

Amount

Taking down chowkats or frames with shutters exceeding 1.5 Sqm but not exceeding 4.0 Sqm each (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frames with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified & directed.

M & L for aluminium two track sliding window with frame section No 20829 and 20830 of Jindal or equivalent make as approved by GE in writting. The window shutters shall be of section No 20736 & 20738 of Jindal or equivalent make as approved by GE in writting including supply and fixing 5 mm thick tinted glass, glazing clips, rubber beading alongwith roller, locking arrangement etc. as required complete all as specified and directed.

S & F 5 mm thick aluminium grill of mesh size not exceeding 80 mm in both direction fixed with Y channel complete all as specified and directed.

S & F stainless steel wire cloth of size 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed.

M & L for aluminium anodised doors made out of anodised aluminium extruded section with door frame section 101.60 x 44.45 mm x 2.00 mm size and door shutter single/double leaf frame section top rail section 83.50 mm x 44.45 mm x2.00 mm, middle rail section 123 mm x mm 44.45 mm x 2.00 mm, bottom rail section 101.60 mm x mm 44.45 mm x 2.0 mm, side rail/style section 83.50 mm x 44.45 mm x1.50 mm with 5.00 mm thick tinted glass on top half portion and 9 mm thick prelaminated particle board exterior grade on bottom half portion including rubber gasket, aluminium beading, glazing clips, aluminium fancy handle, tower bolt 150mm long, heavy duty double action floor springs with foundation box, 6 lever mortize lock with duplicate keys and all other required fittings as per standard engineering practice complete all as specified and directed.

M&L for aluminium anodised partitions frame section single groove of size 101.60 mm x 44.45 mm x 2.01 mm thick with 5.50 mm thick tinted glass on top portion and 9mm thick prelaminated particle board exterior grade on bottom portion including rubber gasket, aluminium beading, glazing clips, partition fixed with self driven screws complete all as specified and directed. (Note :-Each glass pan should not be more than 1.0 Sqm each).

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets in any thickness including cover fillets if any complete all as specified and directed.

M & L for 16 mm thick and size 600 mm x 600 mm mineral fibre false ceiling system of pattern classic lite RH 99 (bevelled tegular) of Armstrong or equivalent make and model as approved by GE in writting including grid system using hot dipped galvanised steel section, exposed surface with pre-powder coated capping, main runner and cross runner and to comprise main tee/runner of 15mm x 38 mm size (load carring capacity 14 kg/sqm) spaced at 1200 mm c/c securely fixed to the structural soffit and flush fitting 1200 mm long cross tee/runner to be interlocked between main runners at 600 mm centre to centre from 1200 mm x 600 mm module, cut sub cross tee/runner 600mm require independent support. Wall angle of size 19mm x 19mm, secured to the periphery of the wall at 450 mm maximum centres. The above grid is suspended at every 1200 mm centre to centre in both direction and starting from wall at the distance 350 mm from wall by using 3.50 mm dia aquline wire with suitable fasterners and hook clip complete all as specified and directed.

Dismantling floor ( tiles / kota / granite), hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed.

M & L for vitrified ceramic coloured tiles 10 mm thick (square/ rectangular) area of each tiles not exceeding 0.36 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and directed.

Ditto all as per item No.11.00 here-in-before but as in dado/skirting over and including 10 mm thick rendering in CM (1:4) complete all as specified and directed.

M & L for brick work with fly ash old size bricks, straight or curved on plan exceeding 6 m mean radius built in CM (1:4) complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M & L for rendering 15 mm thick on brick work/ concrete surfaces in CM (1:6) on wall, finished even and smooth without using extra cement complete all as specified and directed.

Complete removal of existing treatment on walls complete all as specified and directed.

M & L for preparation of new/old surfaces of walls and applying two coat of Oil Bound Distemper over a coat of primer over and including 1 to 2 mm thick wall care putty complete all as specified and directed.

M & L for preparation of old painted steel and iron surfaces of any description over 10cm girth or width not otherwise described and applying two coat of synthetic enamel paint complete all as specified and directed.

E/M PORTION :- Taking down old unsevicable/deteriorated batten/PVC conduit / MS conduit point wiring from existing place i.e, light, fan, socket or power points complete with all unservicable fittings such as switches, sockets, ceilings rose, pendants, Holders etc and making good all disturbed surface to wall, floor etc by means of cement mortar (1:3) or plaster of Paris to match/finish as the existing surface either by using same color distemper, putty or white/colour wash complete all as specified and directed.

Taking down main switch/DB/ changeover/ AC box of any capacity including fixing accessories complete all as specified and directed.

M & L for concealed /surfac point wiring on wall and ceiling / roof with necessary fixing arrangements with PVC-FRLS insulated and unsheathed cooper multi-stranded conductor of size 1.5 Sqmm, 1100 Volts grade drwan in and including rigid non metallic white/ ivory PVC conduit medium grade ISI marked not less than 19mm dia with all conduit accesories /fittings such as junction boxes, bends, tee, elbow etc. including anodized MS sunken boxes made out of MS Sheet of thickness not less than 1.6 mm with earth dolly and Bakelite laminated sheet 3 mm thick ISI marked for fixing of switches/ sockets, fan, regulators, wall mounting fittings, door bell & bulkhea etc. with MS screw and cup washer including PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 Volt grade for continous earthing including cutting the chases and making good the surface by cement mortar(1:3) and for matching finishing either by means of plaster of paris /putty or disptemper / colour wash with same existing colour surfaces complete all as specified and directed.

Ditto all as per item No.21.00 here-in-before but for one socket point controlled by one switch on same board.

Ditto all as per item No.21.00 here-in-before but for 5 Amp independent socket point controlled by one switch.

Ditto all as per item No.21.00 here-in-before but for power point wiring with 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 Volt grade cable and 1.5 Sqmm PVC-FRLS insualted, unsheathed, copper conductor, standed 1100 Volt grade cable as continous earth lead.

M & L for switch flush type singe pole one way 5 Amps, 240 Volts, white finish complete all as specified and directed.

M & L for switch flush type 15 Amps, 240 Volts singe pole, white finish complete all as specified and directed.

M & L for socket outlet 5 pin, 5Amps flush type, white finish complete all as specified and directed.

S & F socket outlets 2 in 1, 3 pin, 5/15 A, flush type universal, 240 V white finish complete all as specified and directed.

S & F electronic socket size, rotary, 5 speed step type regulator, 120-230 V white finish complete all as specified and directed.

S & F ceiling rose, surface backlite, 65 mm x 20 mm three terminal complete all as specified and directed.

S & F double door metallic sheet metal enclosure for DB when MCBs to be used SPN 8 ways, 240 V with 200 Amps rated bus bar complete fixed properly on in concealed position on wall and surface position on trusses and to provide requires sizes of flexible conduit at any open surfaces near DBs of cables/ wires including providing of suitable size of lugs and blanking plate complete all as specified and directed.

M & L for recess LED 30 Watt 600 mm x 600 mm fitting made of CRCA powder quoted finish with fully covered by PMMA Acrylic Lumio Diffuser, LED Used shall be SMD type and fixture should have minimum efficiancy at System level (Not Chip level) @100lumens/watt, Life of fixture 50000hrs@L70% Lumen maintenance, CCT up to 6500, CRI > 80, PF>0.95, an operating Voltage Range of 140-270 V minimum Internal Surge Protection 2.5KV. The fixture should comply with the parameters as per IS 10322 and IEC60598, EMC /EMI complaince, Maximum wattages 37 W, Minimum system Lumens 3400, Philips models RC380B LED30S 6500 G4L60W60PSUODWNOC or equivalent in WIPRO/Havelles as approved by GE in writting complete all as specified and directed.

S & F LED 4 ft Batten capaccity 19 Watt with a nominal stystem lumen output 2000 lumens and a minimum system efficency of 105 lm/V. The luminaire shall have a rated system lifetime of 40,000 burning hours at L70. The luminaire should have a color temprature of 6500K and CRI>80. The luminaire shall meet IP20 rating with THD<10% and PF>0.95. The luminaire housing should made CRCA sheet with PC glosy diffuser. The total power consumption should not exceed 19 W (including driver). Make ENDURALED BATTEMN "BN 108C LED 20S PSU CDL WH" or equivalent to WIPRO/Havelles as approved by GE in writting complete all as specified and directed.

M & L for sub main wiring on surface with two single core PVC-FRLS insulated unsheathed multi stranded copper conductor cable of size 6 Sqmm drawn in MS/PVC Conduit with 4 Sqmm PVC-FRLS insulated unsheathed multi stranded copper conductor as a continous earth wire complete excluding rigid stove enameled steel conduit ISI marked of size not less than 32 mm dia in conealed / surface wiring including all fittings such as tee, bends, reducer, elbow, bell mouth, tube ends and all fixing accessories such as couplers, locks, nuts, sadles, pipe hooks etc. fixed properly including taking down old unservicable sub main wiring complete all as specified and directed.

S & F in replacement testing and commissioning of MCB SP 240 Volt, 6 Amp to 32 Amp, 10 KA capacity having C -Curve characteristics connected with suitable lugs complete all as specified and directed.

Ditto all as per item No.35.00 here-in-before but for SPN 16-32 Amps.

Ditto all as per item No.35.00 here-in-before but for SPN 40-63 Amps.

M & L for earthing complete with M.S galvanized earth plate electrode of size 600X600X6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal GL) with top edge of the earth plate not less than 1.5 m below normal GL, connected to galvanized earth lead wire of size 4 mm dia by means of bolts, nuts, check nuts & washer of GI or steel including excavation, PCC (1:3:6) type C-1 using 20mm graded stone aggregates, chamber with 40mm thick RCC Cover (1:2:4) type B-0 using 12.5 mm graded stone aggregates reinforced with 6mm dia bar, 3 Nos both way, 15mm dia light grade GI protection pipe, funnel with wire mesh, watering pipe of size 20mm dia med. grade, lugs, main Earthing lead upto 7.5 m including Charcoal dust, salt etc. all as shown in electrrical plate No. 3 of SSR Pt-I, 2009 Specifications complete all as specified and directed.

S & F 20 mm dia PVC conduit rigid metallic medium ISI marked in concelaed position including all fittings such as tee, bends, reducer, elbow, bell mouth, tube ends and all fixing accessories such as couplers lock, nuts, saddlers, pipe hooks etc fixed properly on as in concealed /Surface position complete all as specified and directed.

S & F wall mounted air circulator 600mm sweep 1400-1500 RPM, 240 Volts including proper fixing arragments as required at site and connecting to ceiling rose with suitable size of copper flexible cord complete all as specified and directed.

S & F sheet metal enclosure, 32A, 415 Volts triple pole neutral & earth with a three pin and earth plug and socket complete in metal clad board (Industrial type) with one TP MCB 32 Amp fixed properly on/in concealed position complete all as specified and directed.

aarohi nirman company