GE/CHM-17/2023-2024 REPAIRS TO ROOF TREATMENT / CHAJJA/RAILLING AND OTHER MISC WORK IN OTM ACCN UNDER AGE B/R II AT CHANDIMANDIR

Amount

Taking down chowkhats or frame n.exc 1.5 Sqm with shutter (without taking off shutters from the frame) and removal from site complete all as specified & directed.

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm with shutter (without taking off shutters from the frame) and removal from site complete all as specified & directed.

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each, and removal from site complete all as specified & directed.

Taking down shutters of any description exceeding 1Sqm but not exceeding 2sqm each including stacking at location as directed by Engineer-in-Charge for refixing in same opening(s) after rescuring or easing, adusting, welding, etc., complete all as specified and directed.

Factory made pressed steel frames having profile 125mm x 60mm for doors with one or more rebates made out/fabricated of 1.25 mm thick MS sheet, including necessary fixing lugs, hinges, lock strike plate, thress hold bar/flat etc. complete ,all as specified and directed.

Factory made pressed steel frames having profile 105mm x 60mm for doors with one or more rebates made out/fabricated of 1.25 mm thick MS sheet, including necessary fixing lugs, hinges, lock strike plate, thress hold bar/flat etc. complete, all as specified & directed.

30mm thick flush shutters, solid core costruction, with block board core and plywood face panels, commercial type on both sides as in cupboards, etc. complete all as specified and directed.

35 mm thick, factory made, second class hard wood, plain framed hammer marked, panelled shutter (two panel)with lock rail and panel of 9 mm BWP commercial ply both face including 1.00 mm thick sunmica (lamination) on both sides of p-anel and 20 mm x 20 mm x 10 mm wooden beading all round the panel. The size of rail and stile as per IS : 1003 (Part I) kiln seasoned and chemically pressure treated complete all as specified and directed.

Glazed and gauged skelton shutter (Factory made) 35mm thick of second class hard wood open rebated & prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut & mitred beads for securing glass etc including priming coat. Size of members of shutters as specified in SSR Part I Section 8, clause 8.20 (a) including Kiln seasoned and chemically pressure treated, a shop coat of pink primer complete all as specified & directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specifications & drawing mentioned on Srl Page No. 134, 135 and 146 of SSR Part-II including aluminum iron mongery. MAKE : M/S RAJSHREE PLASTIC WOOD, INDORE/SINTEX

100 mm size butt hinges medium weight cold rolled mild steel complete, all as specified and directed.

100mm butt hinges , extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed for PVC door, type C-21 complete all as specified and directed.

200 mm size aluminium , barrel tower bolt of extruded section and fixed complete all as specified and directed.

150 mm size aluminium, barrel tower bolt of extruded section and fixed for PVC door complete all as specified and directed.

150 mm aluminium handles cast type complete all as specified and directed.

250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed,complete all as specified and directed.

300mm MS ordinary rat tail rod pattern spring incl roller plate complete all as specified and directed.

Floor door stopper of aluminum alloy body and tongue, anodized with hard drawn steel spring, fixed in floor (140mm size), fixed as in repairs, complete all as specified and directed.

Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Factory made steel window box type with side hung shutters including box type hinges and one shop coat of red oxide primer, 125mm steel handle-02 Nos mild steel ISI marked tower bolt 125mm size (minimum 2 for each shutter) complete with glazing bars, dovetailed or welded fixed with and including MS flat of suitable size for fixing grills and guards bars etc as in repair complete all as specified.

Factory made steel window box type with side hung shutters including box type hinges and one shop coat of red oxide primer, 125mm steel handle-02 Nos mild steel ISI marked tower bolt 125mm size (minimum 2 for each shutter) complete without glazing bars, dovetailed or welded fixed as in repair complete all as specified.

Factory made box type steel ventilators, openable with side hung shutters with box type hinges including one shop coat of red oxide primer, hinges, tower bolts 100 mm, steel handles and steel peg stay complete without glazing bars devetailed or welded fixed in repair complete all as specified and directed.

Galvanised mild steel wire cloth 0.56 mm nominal dia of wire & avg width of aperture 1.18 mm in fixed with tinned tacks complete all as specified and directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

Aluminium (extruded section body) door closer hydraulically regulated designation No. 3, universal type, suitable for door shutter of 851 mm to 1000mm in width and of weight between 61 to 80 Kg complete, fixed in repairs, all as specified & directed by Engineer-in-charge.

Supply only 5.5mm thick tinted sheet glass fixed to aluminum frame work with standard anodized aluminum snap beading, rubber packing, aluminum screws etc in panels exc 0.5 Square metre in each pane, complete all as specified & directed.

Supply only 9mm thick pre laminated particle board (ISI Marked), exterior grade, pre laminated both side with decorative choice lamination and other side balancing white lamination, fixed with beading to aluminium frame work as in panel of shutter / built in locker after taking out old board, complete all as specified and directed .

Hacking out old broken glasses (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified & directed by Engineer-in-charge.

3mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Square Metre in each panes complete all as specified and directed.

4mm thick figured glass pin head type ordinary quality any size and in any type of frame and glazing with oil putty (or beading) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

Framed work such as grill guard bars etc welded to steel frame MS round/square bar conforming to Fe 290 Gde-E 165 complete all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of red oxide, zinc chrome complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings including ridges, all as directed.

Pre-painted galvalume aluminum zinc coating (AZ-70) GI based corrugated steel sheet 0.50mm thick in any colour and patteren as approved by the GE of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, hips , valley gutters, drip and straight flashing (length and girth as fixed), fixed with self tapping screws complete all as specified & directed by Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified & directed by Engineer-in-charge.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.290.Gde-E-165, fixed as in repair complete all as specified.

Dismantling boarding any description fixed in any position with nails complete all as specified & directed.

Standard GI snap grid of size 605mm x 605mm frame work for false ceiling with main tee 32 x 24 x 1mm thick cross tee 26 x 24x 4mm thick and wall angle 24 x 24x 1mm thick having flange powder coating and covered with PVC thin sheet same to placed in grid by means of ceiling and grid to be tied properly / suitabely by GI strip / GI wire in truss / ridge / purlin complete all as specified and directed.

Perforated particleboard/ tiles for insulation and accoustic purposes, 60x60 cm in size, fixed with nails to timber frame work or withstaples on snap gridSupply only prelaminated particle board 7mm thick of size 600 x 600mm, interior grade, preliaminated one side with decorative choice lamination and other side balancing white liamination, fixed with staples as in snap grid complete all as specified and directed.

Solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications complete all as specified and directed.

Material and labour PVC sheet fillet 35mm wide, 5mm thick for wall paneling, fixed in repair complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Brick work with sub class ‘B’ bricks of class designation 10 (min. compressive strength 100Kg/sqcm) old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:4 complete all as specified & directed.

All as per Srl item no 46 above but except bricks.

Taking down existing plaster of any description on brick wall/ concrete surface including racking out joints, hacking for key, scrubbing down with water etc complete, all as specified and directed.

10mm thick rendering cement plaster in Cement and Sand mortar 1:3 over brick work or concrete surfaces finished even and fair, as in ceiling, chajjas, facias, at any position, complete all as specified and directed.

15mm thick rendering cement plaster in Cement and Sand mortar 1:6 over concrete /brick surfaces finished even and smooth without using extra cement complete all as specified & directed.

15mm thick rendering cement plaster in Cement and Sand mortar 1:4 over concrete /brick surfaces finished even and fair complete all as specified & directed.

Three coats of white wash on ceiling surfaces including preparation of new plastered surfaces complete all as specified and directed

Three coats of oil bound distamper on new surface of wall including a coat of primer, complete all as specified and directed

Preparation of new plastered or un-plastered surfaces of walls and applying two coats of cement base paint, over a coat of primer complete all as specified and directed.

Preparation of old decorated plastered surfaces of walls and applying two coat of white wash complete all as specified.

Two coats of oil bound distemper on wall over a coat of primer including preparation of old surface complete all as specified and directed.

Preparation of old plastered surfaces of walls and applying Two coats of cement base paint, complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness. (Below or above ground level) complete all as specified and directed.

50mm thick plain cement concrete type C-1 1:3:6 (Using 20mm graded crushed stone aggregates) as in plinth protection finished fair and even without using extra cement complete all as specified and directed.

100mm thick plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation, sub base and mass concrete complete all as specified & directed.

Concrete interlocking pre polished paver block, with grey cement and pigment, design as approved, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over and including 25mm thick sand cushioning, complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish of the premisses, complete all as specified and directed.

Non skid ceramic coloured tiles of size 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, superior quality as in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in cement mortar (1:6) complete all as specified & directed by Engineer-in-charge

Glazed ceramic tiles, coloured in vertical surface 300mmx450mmx 7mm thick, joint free, first quality, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over 10mm thick rendering in cement mortar 1:4, complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15 mm thick screed or bedding layer in CM 1:6, complete all as specified and directed.

Vitrified ceramic tiles coloured first quality dark shade 8 to 10mm thick (square / rectangular) polished, area of each tiles n.exc 0.36 Square metre, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Machine cut kota stone slab on vertical/horizontal surface like floors, skirtings etc, 16-18mm thick , best quality, width and length as ordered over and including 15mm thick screed bed in cement mortar( 1:4), bedded and jointed with grey cement slurry and pointed with grout of matching shade including moulding and all necessary cutting and machine polishing, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors laid, bedded and pointed in any mortar including disposal of demolished material n.exc 1.5 km complete all as specified and directed.

Granite stone slabs, 16 to 18mm thick, width and length as per site requirement, best quality machine cut and polished to be fixed in floors,cooking plateform, tread, raiser of steps and vertical surfaces etc and jointed with gray cement slurry and pointed in white cement mixed with marble dust (1:2) with admixture of pigment to match the shade of slab, rubbing, cutting / rounding of edges and corners where required with and including 15 mm thick screed bed in cement mortar 1:4, Complete all as specified and directed.

Vitreous china wash basin white, flat back of size 550 x 400 mm white including, pillar tap waste fittings, brass chromium plated coupling, brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe fixed as in repair complete all as specified & directed by Engineer-in-charge.

Vitreous china squatting pan, “Orissa” pattern size 580mm x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe, set with cement concrete, fixed as in repair, complete all as specified & directed.

Vitreous China Wash down water closet (pedestal pattern) , white, with and including PVC seat cover, complete all as specified and directed.

Vitreous China half stall urinal, fixed against wall in cement mortar (1:2), securing urinal with and including 60mm long brass screws, pointing around urinal back in cement, including CP waste coupling, 32mm PVC waste pipe, fixed in repairs,complete all as specified and directed.

Urinal spreader, of PTMT (Minimum weight 60gms) white , suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 20mm bore pipe, fixed as in repairs complete all as specified and directed.

Bib taps brass, fancy type, Short body with wall flange, standard chromium plated, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, fixed as in repairs compl complete all as specified and directed.

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Stop valve (concealed type), chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Chromium plated, fancy type shower rose with swivel joints 125mm dia with arm and fixing to steel pipe 15mm bore, fixed as in repairs, complete all as specified and directed

White PVC valveless flushing cistern (Duel type) of capacity 10 litres, syphonic action , low level with inlet, ball valve, float, handle, PVC connection & 32mm dia CP flush pipe (long type for squatting pan) incl brackets, as in repairs, complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed stone ware / AC/RCC drain pipe etc) internal dia of pipe 150mm. Set in cement mortar including PCC packing in bed and hunching complete all as specified and directed (excavation and earth work shall be measured and paid separately).

Supply and fixing PVC (SWR) pipe 110mm bore single socketed in any length with rubber ring joints, laid in trenches or in flors, complete all as specified and directed.

Supply and fixing PVC (SWR) pipe 75mm bore single socketed in any length with rubber ring joints, laid in trenches or in flors, complete all as specified and directed.

110 mm bore PVC (SWR) bends of any radius complete, all as specified and directed.

75 mm bore PVC (SWR) bends of any radius complete, all as specified and directed.

Supply and fixing PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, fixed in repair complete all as specified and directed

PVC (SWR) 'P' trap 110 mm bore, fixed as in repair complete all as specified and directed.

PVC (SWR) 'S' trap 110 mm bore, fixed as in repair complete all as specified and directed.

75mm bore PVC (SWR) vent cowl complete all as specified and directed.

Toilet paper holder, cast copper alloy, chromium plated fixed in position, fixed as in repair , complete all as specified and directed.

PVC connection 15mm size with PTMT nuts of length 450mm long as in repairs complete all as specified and directed.

PVC (SWR) floor trap 100mm bore, plain with grating incl jointing with solvent cement, fixed as in repairs, complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

15 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors, including taking down old pipe complete all as specified and directed.

20 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors, including taking down old pipe complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc and cutting chases for concealed water tubing & making good, cutting not exc 10 cm girth, in brick walls complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in soft and loose soil all as specified & directed by Engineer-in-Charge.

Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified & directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil all as specified.

Removing excavated materialexc. 1.5 Km but n.exc 5.00 km and depositing where directed at level n.exc. 1.50 mtr above starting point complete all as specified.

Plain cement concrete 1:2:4 type B-0 using 12.5mm graded aggregate as in roof kerbs or mud stops rounded or chamfered on edges, complete all as specified & directed.

2mm thick fibre glass reinforced translucent corrugated coloured sheeting with side lap, fixed with ‘L’ type or ‘J’ type or cranked hook, bolts, nuts, bituminous washer as in roof, including taking down old sheet complete all as specified and directed.

500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layered, screwable lid, hoisted and fixed in position, including tank nipple, float valve, ball valve 20mm PTMT, including dismantling of existing water tanks and removing from site all as specified in SSR Part-I and all as directed by Engineer-in-charge.

K.L. KATARIA AND SONS

M/s Super Trading Corporation

M/s Om parkash

aggarwal contractors and engineers

PARVEEN KUMAR AND SONS

BANSAL BUILDERS

Standard Const. Co.

RAJESH KUMAR