SPL REPAIR TO DI MAIN WATER SUPPLY PIPE LINE AT THE EAST CAMP LT PANELS AND CONNECTING ITEMS AT CUL D WEST CAMP AND PROVN OF WATER COOLER STREET LIGHT AT CUL I EAST CAMP STREET LIGHTS TCP TO MAIN ADM ROAD AT NORTH CAMP UNDER AGE MFFR UNDER GE N BIKAN

Amount

Supply and fix steel tubular swaged poles type 410SP-31(9.0 meter long) complete with MS base plate and finial and single swan neck, Including foundation and coping complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing LED street light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing LED street light fitting 45 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed by the Engineer-in-Charge.

Material and labour Earthing complete with galvanised iron earth plate electrode of size 60 x 60 x 0.60 cm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI wire 4 mm dia (upto the cross arms) by means of GI bolts/nuts/washers, protected by 15 mm bore GI light grade pipe. Earth plate shall be surrounded by alternate layer of charcoal or coke and common salt 15 cm thick all around bottom and top. 20 mm bore GI light grade pipe for watering and including funnel, wire mesh,RCC cover & frame, PCC (1:3:6) type C2 (using 20 mm graded crushed stone aggregate) as in earthing pit including necessary excavation & earth work, all as specified & shown in electrical plate No. 3 of SSR Part – I. (For Poles) Note:- The unit rate inclydes earth lead upto 7.5 metre length from top of earth plate.

Supply and fix galvanized iron pipe 40 mm light grade ISI Marked complete for cable protection and LED brackets, laid in trenches, floors, fixed to walls, pole with suitable FI clamps complete all as specified and directed ISI marked.

Supply and fixing thermplastic cable junction box with IP 55 weather prrof protection for outdoor installation with knockouts for cable entry of size 250x200x105 mm suitable for LT UG cable 10 Sqmm to 25 Sqmm Make - Sintex and including terminal with MCB 6 Amp with Clamp/Hensel

Supply & fixing FRLS PVC insulated Copper conductor, two core of size 2.5 sqmm complete for terminal box to street/ flood light fitting complete all as specified and as directed by the Engineer-in-Charge.

Boring of holes 110 mm dia, manually without disturbing the top surface for laying of cables/GI pipes under road , pavement, hard standing complete all as specified and as directed by the Engineer-in-Charge.

M&L for PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate as PCC bed in foundations of poles, filling, mass concrete and similar works, complete all as specified and as directed. Note : Volume of pole/strut embedded in concrete shall be deducted for the purpose of payment.

M&L for PCC 1:3:6 type C2 using 40mm graded crushed stone aggregate as in foundations of poles/stay assembly, filling, mass concrete and similar works, complete all as specified and as directed.

Supply, installation, commis-sioning of Water cooler fully stainless steel, electric driven single phase having approx storage and nominal cooling capacity 60/120 ltr complete all as specified.including provn of PVC connection heavy duty 750 mm long with brass union both end suitable for 15 mm bore GI pipe water connection and necessary connection complete. Note:- (i) Rate deemed to be included cost of PVC connection, drain pipe etc

Supply and fixing Feeder pillar box cubical type of comprising size (Panel box size), with bus bar chamber having 4 wire 415 Volts, factory made dust proof vermin proof for out door use made out of CRCA sheet 3.15 mm thick powder coated, machine pressed, both side opening with double door (front & rear) in two shalves with provision of rubber beadings and locking system, danger Notice board infront and rear sides including insulated aluminium bus bar of 600 Amp capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers, each MCCB/ cubical switch shall have be independent opening , panel shall be mounted on angle iron frame and legs made from angle of size 50x50x6mm , frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, legs grouted in PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) complete including all connections/control wiring incoming/out going with suitable size of copper conductor cable,

Supply and fixing LT panel pillar box cubical type of comprising size (Panel box size), with bus bar chamber having 4 wire 415 Volts, factory made dust proof vermin proof for out door use made out of CRCA sheet 3.15 mm thick powder coated, machine pressed, both side opening with double door (front & rear) in two shalves with provision of rubber beadings and locking system, danger Notice board infront and rear sides including insulated aluminium bus bar of 200 Amp capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers, each MCCB/ cubical switch shall have be independent opening , panel shall be mounted on angle iron frame and legs made from angle of size 50x50x6mm , frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, legs grouted in PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) complete including all connections/control wiring incoming/out going with suitable size of copper conductor cable,

Foundation is not less than 30 cm below ground level and not less than 45 cm above ground level, legs of panels will be grouted in centre of PCC foundation centre place will be open for connection of Under ground cables including provision of following :- (i) MCCB 100 Amp Adjustable thermal setting 16 KA, FP, single frame, thermal magnetic trip (incoming) - 01 Nos (ii) MCCB 4P 63 Amps, 16 kA-03 Nos ( outgoing) (iii) LED indicating Lamps ( R,Y,B) one set-01 (iv) Onload Change Over switch 100 A, 4P-01 nos

Supply and fixing LT panel pillar box cubical type of 1400x1200x450mm size (Panel box size), with bus bar chamber having 4 wire 415 Volts, factory made dust proof vermin proof for out door use made out of CRCA sheet 3.15 mm thick powder coated, machine pressed, both side opening with double door (front & rear) in two shalves with provision of rubber beadings and locking system, danger Notice board infront and rear sides including insulated aluminium bus bar of 320 Amp capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers, each MCCB/ cubical switch shall have be independent opening , panel shall be mounted on angle iron frame and legs made from angle of size 50x50x6mm , frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, legs grouted in PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) complete including all connections/control wiring incoming/out going with suitable size of copper conductor cable,

Foundation is not less than 30 cm below ground level and not less than 45 cm above ground level, legs of panels will be grouted in centre of PCC foundation centre place will be open for connection of Under ground cables including provision of following :- (i) MCCB 200 Amp Adjustable thermal setting 25 KA, FP, single frame, thermal magnetic trip (incoming) - 01 Nos (ii) Aluminium bas bar for Outgoing ( Mini 10 Nos) with Suitable hole inline as per direction of Engr-in-chager (iii) LED indicating Lamps ( R,Y,B) one set-01

S&F of Feeder pillar box outdoor cubical type factory made vermin protected dust proof with canopy, water proof made out of MS sheet 3.15 mm thick and 50 cm x50 cm x5mm thick angle iron base frame having insulated bus bar aluminum 200amps cap 3 phase with neutral bus bar including fixing in PCC bed block complete all as reqd as directed by Engineer in Charge.

M&L for Earthing to Panel / equipments / panels etc with & including galvanised mild steel earth plate electrode of size 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the earth plate at a depth not less than 1.5 m below ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides, connected to & including galvanized mild steel strip 32x6 mm as earth lead, including nuts, bolts, check nuts & washers of galvanized iron or steel and riveted/welded to earth plate at one end and other end of strip connected to Panel / equipment body / test point with two Nos nuts bolts or welding with steel structure, GI earth strip encased in and including 40mm bore GI light grade pipe with all fittings from upper edges of earth plate upto 7.5 metre above ground level fixed with and including 25x3mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from earth pit to top of electrode and including funnel, wire mesh, copper lugs etc complete with earth pit in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and 40mm thick RCC (1:2:4 type B1) cover complete all as specified and shown in electrical plate No 3 of SSR Part-I including necessary excavation and earthwork in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance not exc 50m complete all as specified and as directed. Note : PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner.

Dismantling and taking out existing broken/unserviceable DI/CI pipe of size 150mm bore including fittings from trenches, walls, floors, etc including cutting/burning out joints and bailing out water from trenches where required complete all as specified and as directed.

Supplying, laying, jointing and testing Ductile iron pipe class K-9 confirming to IS : 8329 of bore 150 mm (ISI marked) with spigot & socketed ends centrifugally cast suitable for rubber tyton joints complete all as specified including rubber tyton joints complete all as specified and as directed by the Engineer-in-Charge.

Laying only, jointing and testing old serviceable DI water Pipe of 150mm bore obtained serviceable vide serial item No. 17 here-in-before including cleaning the pipe from inside & outside properly including rust & mud removal, with & including new fittings and fixed to walls and ceilings or laid in floors, trenches etc in new or old position complete all as specified and as directed.

M&L for rubber tyton push on gasket joints in spigot and socketed DI pipes and fittings of 150 mm dia bore complete all as specified and directed.

M&L for boring below road surface/hard standing suitable for inserting 150 mm dia pipe including removal of surplus soil and making good distrub surface complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of 80mm dia double air relase isolating type valve ISI marked confirming to IS-14845, flanged and drilled including jointing material such as nuts, bolts, washers and rubber sheet etc all directed by Engr-in-Charge

Supply& fix in replacement , laying, jointing, testing and commissioning LT XLPE insulated, PVC sheathed armoured heavy duty electric cables LT 1100 volt grades with aluminium stranded conductor passing through pipes, in duct, on poles,in trenches, under road etc complete all as specified and directed of following :- (a) 95 sqmm, 3.5 Core

(b) Ditto all as per item no-23 above but 70 sqmm, 3.5 Core

(c) Ditto all as per item no-23 above 50 Sqmm 3.5 core

(d) Ditto all as per item no-23 above 35 Sqmm 3.5 core

(e) Ditto all as per item no-23 above 25 Sqmm 3.5 core

(f) Ditto all as per item no-23 above 16 Sqmm 2 core

Supply & Laying & testing cross linked poly-ethylene ( XLPE) insulated, screened PVC bedded, galvanised steel strip of wire armoured electric power cables (heavy duty) with stranded aluminium conductor 1100 volts grade, LT grade of cross sectional area 10 Sqmm 4 core laid in trenches /through pipe in road crossing /paths /drains/ducts/ floors/along poles/walls /ceilings /equipments etc supplied and fixed including commissioning and testing complete all as specifed and as directed. Make : Polycab/KEI/Havells

Excavating in trenches, not exc 1.5 metre wide and not exc 1.5 metre in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying cables, pipes, etc. not exc 10 Sqm on plan & not exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

Ditto all as per serial item No. 30 here-in-before but depth exc 1.5m and not exc 3m.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil complete all as specified and as directed.

Removing excavated soil/material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and as directed.

M&L for dry sand (Local Tibba sand) and punning for cushioning and cover for protection of under ground electric cable complete all as specified and as directed. Notes : (i) Approved local Tibba dry sand free from vegetations, grass and other deleterious substances shall be used. (ii) For the purpose of payment, only punned thickness shall be measured.

M&L for sub class ‘B’ (old size) clay bricks laid flat and dry abutting each other with gap between adjacent bricks not exc. 10mm for protection of underground electric cable in such a way that the length of brick is at right angle to the central axis of cable complete all as specified and as directed.

Supplying and fixing of automatic street light switch using infrared sensor based Nture Switch-, 25 kw equally distributed, 63 Amps,3-pole, Model - Swadeep-02 EC 25 Kw3P for automatic switching of street lights based on LUX level of natural light . The sensor(Nature switch ) along with suitable power contactor rating 63 Amps 3- pole & 40 Amps 2-pole, MCB SP 63 Amps -03 nos and support terminals should be enclosed in pole/wall mountable enclosure made of rust proof ,electric shock proof, termite proof and FR grade SMC Junction box (Sintex make) confirming to IP54.The contactor suitable to 3- phase load of 25 kw , rating 63 amps 3pole, MCB rating 63 amps SP 03 NOS.

S.K BUILDERS AND ENGINEERS

Gill Construction Co

M/S Shree Ram Enterprises

S S CONSTRUCTION