SPECIAL REPAIRS TO BLDG NO P-02 HERITAGE BLDG, GUN HOUSE AT MIL STN BHUSAWAL UNDER GE (S) AHMEDNAGAR

Amount

Dismantling of AC sheet (corrugated, semicorrugated etc) as in roof covering including ridges complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar all as specified and as directed.

Demolition of cement concrete in ground floors and pavings n exc 15cm thick (below or above gound level) all as specified and as directed.

Demoltion of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. all as specified and as directed.

Dismantling timber scantlings 40 Sqcm and over in section, in any position, framed work complete all as specified and as directed

Dismantling timber in fillets, rails, posts, rafters, purlins etc under 40 Sqcm in section, in any position, framed work complete all as specified and as directed

Dismantling wrought iron or mild steel work of any description and in any position complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement morter bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and as directed.

Taking down chowkats or frames not exc 1.5 Sqm each with shutters without taking off shutters from the frames all as specified and as directed.

Taking down chowkats or frames exc 1.5 Sqm but not exc 4 Sqm each with shutters without taking off shutters from the frames all as specified and as directed.

Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm each all as specified and as directed.

Taking down shutters of any description exc 2 Sqm each all as specified and as directed.

Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm each and refixing in same opening all as specified and as directed.

Taking down shutters of any description exc 2 Sqm each and refixing in same opening all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads all as specified and as directed.

Taking up or down 15mm bore steel tubing and connections etc. all as specified and as directed.

Taking up or down 20mm bore steel tubing and connections etc. all as specified and as directed.

Taking up or down 25mm bore steel tubing and connections etc. all as specified and as directed.

Excavation in trenches, n.exc. 1.5m wide and n.exc. 1.5m in depth; for foundations, etc or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soil complete all as specified and as directed.

Removing excavated soil to distance n.exc. 50m and depositing where directed at a level n.exc. 1.5m above the starting point complete all as specified and as directed.

M&L for PCC 1:3:6, type C-1 (using 20mm graded stone aggregate) as in hold fasts, bed blocks, bed plates, concrete filling around pipes including necessary formwork complete all as specified and as directed.

M&L for reinforced cement concrete 1:2:4, type B1 using 20 mm graded stone aggregate as in landings, cover slabs (for man holes etc.) including use of necessary formwork complete all as specified and as directed.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4 complete all as specified and as directed.

M&L for first class hard wood plain, solid, segmental work from solid and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue and pinned at joints as in handrails, rounded, or shaped with splayed faces in straight lengths and fixed all as specified and as directed

M&L for first class hard wood as in baluster etc of size 75mm x 60mm, rounded or shaped with splayed faces in straight lengths and fixed all as specified and as directed

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/Cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and as directed.

S&F 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats all as specified and as directed.

S&F 30mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (b); supplied and fitted to chowkats all as specified and as directed.

S&F in repairs block boards, 18/19 mm thick, grade 1 quality, exterior grade, commercial type with and including first class hard wood beading (18/19mm x 6mm) all around as in cupboard shutters and fixed to frame all as specified and as directed.

S&F solid PVC wall lining consisting of 5mm thick single side prelaminated PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing all as specified and as directed.

S&F solid PVC 5mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specifications and drawing all as specified and as directed.

S&F 75mm size mild steel butt hinges, medium weight, cold rolled and fixed all as specified and as directed.

S&F 100mm size mild steel butt hinges, medium weight, cold rolled and fixed all as specified and as directed.

S&F 200 mm size aluminium anodised, barrel tower bolts of extruded section and fixed all as specified and as directed.

S&F 100 mm size aluminium anodised, barrel tower bolts of extruded section and fixed all as specified and as directed.

S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised all as specified and as directed.

S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodised all as specified and as directed.

S&F 300 mm long aluminum alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of steel, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and as directed.

S&F 100mm size hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws all as specified and as directed.

S&F in repairs brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges and fixed all as specified and as directed.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanised with width of flap when open 40 mm all as specified and as directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and as directed.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and as directed.

M&L for framed work such as grills, grating etc with end of bars shoulderd and/or riveted, welded or forged into spikes, framed guard bars iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe 290 Gde E-165 all as specified and as directed.

S&F mild steel bands, straps, supports or stays, rainwater ventilating pipes including bolts of required size, hooks (stay) heavy for large gates hook and pintle hinges large hasps and staples chains hand made sliding bolts, clamps, hold fasts, wall tiles, hooks for hanging fans, plain angle cleats for securing purlins to wood truses or fats knee piece insert two way and three way straps plate washers and similar small articles conforming to Fe 290 Gde E-165 all as specified and as directed.

S&F mild steel TMT bars 10mm dia and over as reinforcement, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia all as specified and as directed.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails fixed with angle cleats or other connecting plates, conforming to Fe 410-W(Gde-E-250) quality-A, complete all as specified and as directed.

M&L for mild steel work as in wind ties for roof including securing bolts complete including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F anodised aluminium frame, powder coated for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed

S&F anodised aluminium powder coated door shutters, aluminium section weighing 0.55 kg/ Sqm including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed

S&F double action floor spring, hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all as specified and as directed

M&L for anodised aluminium snap grid framework for false ceiling, size of grid 605 x 605 mm, including 4mm dia GI wire hangers at 1.2m centres, 4mm thick, non asbestos fibre designer cement building boards (decorative type), fixed or laid/ inserted to aluminium framework/grid, preparation of surfaces of ceiling borards and applying two coats of oil bound distemper over a coat of chalk whiting including dismantling existing false ceiling (framework, boards, wire hangers etc) complete all as specified and as directed.

S&F prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, colour and design as approved by GE complete all as specified and as directed.

S&F prepainted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridges, hips, valley gutters, drip and straight flashings fixed with self tapping screws as specified colour and design as approved by GE complete all as specified and as directed.

M&L for 12mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work or as directed complete all as specified and as directed.

M&L for 75mm thick plain cement concrete, 1:2:4 type C-2, using 40 mm graded stone aggregate, as in path, finished even and fair all as specified and as directed

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for 18-20mm thick granite (of any type), table rubbed and polished as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with the shade of granite complete all as specified and as directed.

M&L for 20-25mm thick machine cut and polished Cudappah stone slabs as in cooking platform including cutting chesis in brick wall and fixing the Cuddapa stone in cement mortar 1:2 complete all as specified and as directed.

M&L for 20-25 mm thick machine cut kota stone flooring (size of kota stone slab 22"x22") laid over and including 20 mm thick bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match including cutting, rubbing and mirror finish polishing including removing dust etc complete all as specified and as directed.

M&L for 20-25 mm thick machine cut kota stone slabs on vertical surfaces like risers to steps, skirting etc with and including 10mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match including cutting, rubbing and polishing including removing dust etc complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) area of each tile exc 0.06 sqm but n exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete and with including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for 350 x 250 x 7mm thick or 450 x 350 x 7 mm thick glazed ceramic coloured tiles on vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match complete with and including 10mm thick backing coat in cement mortar 1:4 all as specified and as directed.

M&L for 10mm thick rendering on other than fair faces of brick work or concrete surfaces (internal surfaces of walls) in cement mortar 1:6, finished even and smooth without using extra cement all as specified and as directed.

M&L for 15mm thick rendering in two layers on fair faces of brick work or concrete surfaces (external surfaces of walls) first layer of 10mm thick in cement mortar 1:6 and second layer of 5mm in cement mortar in cement mortar 1:4 mixed, finished even and fair all as specified and as directed.

M&L for preparation of newly plastered or unplastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of chalk whitening primer all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer all as specified and as directed.

M&L for complete removal of existing treatment on walls including cornices by scrapping with steel scrappers or any other means including filling depressions of scrapped surfaces and making smooth surface with one coat of 1mm thick (minimum) wall care putty and applying two coats of oil bound distemper (white or tinted) over a coat of primer complete all as specified and as directed.

M&L for complete removal of existing treatment on walls and roof including removing nails, making good holes cracks etc brooming down or steel wire brushing scrapping down or steel wire brushing scrapping down smoke soots etc and applying two coats of exterior acrylic emulsion, any tint over one coat of exterior acrylic primer with and including provision of scaffolding if required for the treatment to external surfaces of building with required safety measures etc complete all as specified and as directed.

M&L for complete removal of existing treatment on ceiling and applying two coats of plastic emulsion paint (white or tinted) over a coat of primer complete all as specified and as directed.

S&F 4mm thick plain sheet glass and glazing with oil putty in square n exc 0.5 Sqm in each pane and fixed complete all as specified and as directed.

S&F 5.5mm thick plain sheet glass and glazing with oil putty in square exc 0.5Sqm in each pane and fixed complete all as specified and as directed.

M&L for preparation of new wood and wood based surfaces of any description not otherwise described exc 10cm width or girth and applying two coats of synthetic enamel paint on over a coat of pink primer all as specified and as directed.

M&L for preparation of old wood and wood based surfaces of any description not otherwise described exc 10cm width or girth and applying one coat of synthetic enamel paint all as specified and as directed.

M&L for preparation of old wood and wood based surfaces of any description not otherwise described but not exc 10cm width or girth and applying one coat of synthetic enamel paint all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description not otherwise described exc 10cm width or girth and applying two coats of synthetic enamel paint on over a coat of red oxide primer all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description not otherwise described, not exc 10cm in width or girth, when unconnected with other painting or when paintd in a different tint, applying two coats of synthetic enamel paint on over a coat of red oxide primer all as specified and as directed.

M&L for preparation of old painted surfaces of steel and iron of any description, over 10 cm in width or girth, not otherwise described include for all necessary preparatory work required and applying one coat of synthetic enamel paint all as specified and as directed.

M&L for preparation of old painted surfaces of steel and iron of any description, not exc 10cm in width or girth, when unconnected with other painting or when paintd in a different tint and applying one coat of synthetic enamel paint all as specified and as directed.

M&L for writing letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high in synthetic enamel paint (any tint) including preparation of base (area not exc 0.05Sqm) for writing letters with synthetic enamel paint (any tint) complete all as specifed and as directed

M&L for writing stops, commas, short lines, dashes, hyphnes, brackets etc in synthetic enamel paint (any tint) including preparation of base complete all as specifed and as directed

S&F rotational moulded polyethylene water storage tanks of capacity 500 litre (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling old water tank all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks of capacity 1000 litre (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling old water tank all as specified and as directed.

S&F in repairs ball valve, 20mm bore, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed all as specified and as directed.

S&F in repairs, vitreous china wash hand basin, white, flat back, size 550 mm x 400 mm, including brackets, pillar tap 15 mm bore chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, 32 mm dia waste coupling brass chromium plated with long screwed shanks and fly nuts, 32mm size brass chromium plated bottle trap inlet and outlet screwed for pipe or connections including necessary packing union and cap, PVC waste pipe,15mm dia PVC connection pipe complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet (Pedestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

S&F in repairs PVC valveless syphonic action type flusing cistern, 10 litre capacity, low level type, white with inlet, ball valve, float handle , brackets etc complete all as specifed and as direced.

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 630 mm x 450 mm white, with integral foot rests with and including 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets all as specified and as directed

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed to wall with brass screws all as specified and as directed.

S&F in repairs 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repairs 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repairs 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F in repairs 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F in repairs 75mm dia PVC (SWR) bends any radius complete all as specified and as directed.

S&F in repairs 110mm dia PVC (SWR) bends any radius complete all as specified and as directed.

S&F in repairs 110mm dia PVC (SWR) bends any radius with access door complete all as specified and as directed.

S&F in repairs PVC (SWR) branch piece, single (single Y) equal or unequal, 110 mm bore with oval access door all as specified and as directed.

S&F in repairs PVC (SWR) branch piece, single (single Y) equal or unequal, 75 mm bore with oval access door all as specified and as directed.

M&L for 15mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position, 15mm bore galvanised, with and including all new fittings; laid in trenches fixed complete to walls or laid in floors complete all as specified and as directed.

M&L for 20mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position, 20mm bore galvanised, with and including all new fittings; laid in trenches fixed complete to walls or laid in floors complete all as specified and as directed.

M&L for 25mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position, 25mm bore galvanised, with and includig all new fittings; laid in trenches fixed complete to walls or laid in floors complete all as specified and as directed.

S&F in repairs stop valves, fancy type brass chromium plated, 15 mm bore screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed all as specified and as directed.

S&F in repairs bib tap, 15mm bore, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handles screwed down for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs brass chromium plated mixer 15 mm bore for mixing hot & cold water, screwed down for iron pipe and fixed complete all as specified and as directed.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in repairs PVC connection, 15mm bore with PTMT nuts of length 450 mm complete all as specified and as directed.

S&F in repairs waste pipes for wash hand besin, flexible type, 32mm bore and fixed complete all as spcified and as directed

S&F in repairs waste pipes for sink flexible type, 40mm bore and fixed complete all as spcified and as directed

S&F in repairs 15mm bore health faucet with 1.2 metre long flexble pipe and wall hook complete all as spcified and as directed. Model No. ALD-563 of Jaquar or equivalent model of make Mark, Cera as approved by GE

S&F in repairs vitreous china soap dish, white, approximate size 160 x 160 x 90mm and fixed complete in wall all as specified and as directed

Taking down carefully copper/aluminum point wiring (Light, Fan, Socket or power) complete including fittings such as switches, ceiling rose, regulator, sockets etc and making good disturbed surfaces of walls, floors etc and matching with existing surface complete all as specified and as directed.

M&L for point wiring (Light Poin) complete with 1.5 Sqmm single core multistranded copper conductor FRLSH, PVC insluated and unsheathed cable 650/1100 volts grade, confirming to IS-694 1990, drawn through and including PVC casing capping 32mm /25 mm width with all accessories as specified with modular cover plate with frame and modular metal flux boxes, blank plate for mounting fitting & fixture like switches sockets and fan regulators etc including copper earth contunity wire for PVC insulated of size 1.5Sqmm for one light point controlled by one way switch complete all as specified and as directed.

All as per serial item No. 120 but for one fan point controlled by one way switch and regulator.

All as per serial item No.120 but for one 3 pin socket outlet, 5 Amps on same board.

All as per serial item No 120 but for one 3 pin socket outlet , 5 Amps on independent board but below the switch board of light points in the same vertical plane

All as per serial item No. 120 but for one 3 pin socket outlet, 5 Amps on independent board.

All as per serial item No 120 but for one bell point controlled by one bell push.

All as per serial item No 120 but for one light point controlled by two, two way switch.

All as per serial item No. 120 but with 4.0 Sqmm copper conductor cable for socket outlet 15 Amps.

S&F modular switch, single pole, one way, 5/6 Amps, 1 module complete all as specified and as directed.

S&F modular switch, single pole, one way, 16 Amps, 1 module complete all as specified and as directed

S&F modular socket, 6 Amp, 2/3 pin, combined, 2 module complete all as specified and as directed

S&F modular socket, 6 A/16 Amp, 2/3 pin, combined, 2 module complete all as specified and as directed.

S&F modular bell switch, 5/6 Amp, 1 module complete all as specified and as directed.

S&F modular switch, 2 way, 1 module complete all as specified and directed.

S&F modular fan regulator, step type, 120W, 2 module complete all as specified and as directed

S&F ceiling rose, surface bakelite, three terminal type complete all as specified and as directed.

S&F in repairs, decorative, ultra slim, square profile LED lighting fixture with extruded polycarbonate, environmental friendly , energy efficient of capacity 18 Watt , appx 4 feet long, 6500 K with inbuilt driver complete fitting and all other accessories fitting arrangements including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed

S&F in repairs, decorative, ultra slim, square profile LED lighting fixture with extruded polycarbonate,environmental friendly, energy efficient of capacity 10 Watt, 2 feet long, 3000 K with inbuilt driver complete fitting and all other accessories fitting arrangements including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed

S&F in repairs, LED luminaire, 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser, soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed

S&F in repairs, LED light fitting 1x 9W / 1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed

S&F in repairs, lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F in repairs, lamp LED 9/10 Watt, 230 volts 50 Hz AC complete all as specified and as directed.

S&F in repairs 35/40 Watt building mounted LED Security light fitting complete made up of pressure die cast housing with toughned glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07 & 10KV external SPD, including GI bracket made out of GI pipe 40/50 mm bore, medium grade pipe 1.2 m long bend to shape required fixed to pole / wall with 02 Nos MS clamps made out of flat iron 40 x 5 mm including nuts, bolts and washer, painting with two coats aluminium paint over a coat of primer, suitable for LED fitting, complete all as specified and as directed

S&F in repair sheet metal distribution board iron clad, VTPN Load line, double door with IP-54 1K-09 , 12 ways, protection suitable for MCCB as incomer and MCB as outgoing 415 Volts 3 Phase , complete with appripriate size copper bus bar and netural link confirming complete with one MCCB 3 Pole 415 Volts 200 Amp rating, thermal magnetic with rupturing vap 36 KA of the same make as of distribution board & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as reqd at site including testing complete all as specified and as directed

S&F in repair MCB DB double door 8 way SPN with suitable rated busbar 240 V complete all as specified and as directed

S&F in repairs, MCB DB double door 4 way SPN with suitable rated busbar 240 V complete all as specified and as directed

S&F in repairs, MCB DB double door 12 way SPN with suitable rated busbar 240 V complete all as specified and as directed

S&F in repairs, of MCB TPN, C Curve 40-100 Amps, 415 V complete all as specified and as directed.

S&F in repairs MCB single pole & Neutral (DP) 240 volts 40-63 Amps "C" curve complete all as specified and as directed

S&F in repairs MCB single pole 240 volts 6 to 32 Amps "C" curve complete all as specified and as directed

S&F in repairs single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp 240 Volts complete all as specified and as directed

M&L for sub main wiring with 2 runs of 4.0 sqmm, single core, PVC insulated & unsheathed cable, conforming to IS-694, 1100 volts with copper conductor, multi stranded, drawn in and including suitable size PVC Casing Caping (ISI marked) with all accessories such as Tees, Elbows, junction box etc as requied alongwith one run of 4.0 sqmm single core PVC insulated & unsheathed copper conductor as continuous earth wire dolly and connecting to existing main switch board / distribution board of each building as ordered and testing on completion including taking down old submain wiring and any type of casing/caping/Conduit, complete all as specified and as directed. Note : Two runs of 4.0 Sqmm cable, one run of 4.0 Sqmm cable and one run of PVC casing/caping shall be measured as one unit all as specified and as directed.

M&L for sub main wiring with 2 runs of 2.5 sqmm, single core, PVC insulated & unsheathed cable, conforming to IS-694, 1100 volts with copper conductor, multi stranded, drawn in and including suitable size PVC casing caping (ISI marked) with all accessories such as Tees, Elbows, junction box etc as requied alongwith one run of 2.5 sqmm single core PVC insulated & unsheathed copper conductor as continuous earth wire dolly and connecting to existing main switch board / distribution board of each building as ordered and testing on completion including taking down old submain wiring and any type of casing/caping/conduit, complete all as specified and as directed. Note : Two runs of 2.5 Sqmm cable, one run of 2.5 Sqmm cable and one run of PVC casing/caping shall be measured as one unit.

S&F in repairs, garden light of bamboo type IP 65 of capacity 9/8 watt, 6000K new generation, energy saving, environmental friendly, long life aesthetically designed aluminium landscape luminaire for diffused lighting with high power LED as light source with PCC base for fixing of lights with proper nut & bolts including electric connection wire complete all as specified and as directed. Make- Cat part No of Havells LHEVBDP7IN6K008 or eqivelant to Crompton/Bajaj/Philips/C&S/Surya/Halonix/Luker

S&F in repairs, post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete including suitable size of GI pipe as per lamp size including connection and testing complete all as specified and as directed.

Supply, laying and testing 10 Sqmm 2 Core, XLPE insulated, PVC sheathed, conforming to relevant IS, ISI marked, earthed system, armoured heavy duty, electric cable with aluminium conductor, 1100 volts grade, in trenches/wall/floor/pole complete and making connection including suitable size Aluminium lugs, including taking out existing cable and cable covers all as specified and as directed .

All as per serial item No 155 but 50 Sqmm 3.5 core

M&L for double walled corrugated (DWC) HDPE Pipe of outer dia 50mm and internal dia 38mm including 90 degree bends with coupler and rubber ring laid in trenches of size 50 mm suitable for cable protection of size 2 core 10 sqmm to 3.5 core 70 Sqmm all as specified and as directed .

S&F 40mm bore galvanised steel tubing, light grade, ISI marked, for protection of under ground cable on pole/wall/under road including taking out old unserviceable pipe all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode, 60cm x 60cm x 6.0 mm thick, burried directly in ground(earth pit not less than 2.25metre deep below normal ground level) with top edge of earth plate not less than 1.5 metre below normal ground level, connected to and including galvanised earth lead wire of 4 mm dia from earth pit to each qtr DB by means of nuts & bolts, check nuts and washers of galvanised including PCC pit of 1:2:4, type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, mild steel angle iron 25 x 25 x 3mm in frame, excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate No 3 of MES sch 2009 (Part I), including taking down old earthing connected to main switch board all as specified and testing on completion all as specified and as directed.

M/S H.N.ENTERPRISES

Bhirud Electric Stores