MID/AN/17

Dismantling of the 3 cusec discharge 18 mtr. head HC pump at lift irrigation station Kot by way of demounting the pumping machinery from the bed plate after removing the pump, motor ,electric connections, coupling pulleys, suction and delivery pipes and finally removing the base frame . Breaking the damaged RCC foundation block with the help of chisel, concrete cutter , electric jack hammer , tools/tackles. Cutting of steel members with the help of cutter stepwise during the process of breaking the RCC block and stacking. Completely removal of broken concrete, soil and TMT bars from pump room in such way that the machinery and electric equipments of other pumping machinery are not damaged /effected. Disposal of salvage/debris of dismantled foundation away from pump room to such a place where irrigation land and water source is not polluted. Construction of RCC foundation block of size- 6ft length x 3 ft width x 3.5 ft depth by way of making surface even for laying of new RCC foundation block. Fabrication of steel mesh out of 10 mm TMT bars members placed vertically and horizontally at equidistance of 6 inches. Laying of 6 inch concrete base at the bottom to level the surface . Placing of fabricated iron mesh in foundation pit and leveling / aligning it with pumping unit. Fabrication and grouting of 8 no. foundation bolts of size 3 ft in foundation block . Laying of RCC foundation block by filling the concrete in the ratio of 1:1.5:3. The size of the block above the ground level should be of original size and alignment in respect of suction and delivery pipes. The block shall be filled with rich mixture of concrete with using vibrator for compaction. The entire block as one unit is to be laid in such a way that it can damp all types of mechanical vibrations created by dynamic load of pumping unit without causing any defect to the pumping unit as well as to the block itself. Fixing of the base frame after leveling and fastening with foundation bolts . Complete job includes cost of material such as cement , sand, steel gravel , shuttering charges, charges for concrete mixture , vibrator charges and labour charges of skilled as well as semi skilled labour , curing charges. The material has to be carried to Lift irrigation station from crusher . Providing/ Fitting and installation of Raw water H.C. pump of 3 cusec discharge, 18 meter head coupled with 40HP induction motor 3 phase 1440 rpm at LIS Kot in place of exiting pump. Recommended make of Pump : Kirloskar make or any reputed make as per IS standards Type of Pump : End suction HC Pump. Recommended make of Motor:- Kirloskar make or any reputed make as per IS standards Type of water-: Raw water. The Job includes shifting of HC pump to Lift irrigation station Kot by mechanical transport . Unloading of pump and then shifting to the LIS manually. Fitting of new pump on the base frame , fastening of suction and delivery pipes with the pump assembly by flanged joints. Fitting and Installation of suitable rating 3 phase motor on the base frame with help of chain pulley block, tripod stand and manual labour. Fitting the motor assembly with help of nuts, bolts and washers. Fitting of new C.I. Coupling/ flexible coupling as per the size of the pump shaft and motor shaft and coupling the pump & motor unit by providing and fitting of cotter, rubber bushes, nuts & bolts. Checking the alignment of the pump and motor assembly with the help of tools and tackles, welding set/gas cutting equipment and manual charges and then extraction of pipes. The job includes replacement of rusted MS suction pipe by way of providing/fitting of new 200mm dia MS suction pipe of length 10mtr. The Job includes modification in suction and delivery pipe as per site condition. Fastening of the MS suction pipe and delivery pipe to the suction and delivery side of pump by using nut, bolts ,washers and rubber packing . Checking the alignment with the help of tools and tackles. Making of electrical connections to the motor. The job also involve arrangement for priming for the newly installed pump. After priming of the pump, testing and commissioning of the pumping unit on full load. The Job includes providing and fitting of new mechanical control valves of PN10 rating i.e. 1 no. foot valve of 200 mm dia , 2 no. sluice valve of 200mm dia and 1 no. reflux valve of 200mm dia. of reputed manufacture like Kirloskar, KSB etc. The job includes providing and fitting of oil immersed delta starter for 40HP Motor of reputed make like L&T etc. The Job includes providing and fitting of copper cable of 16 mm2 of 85 mtr length or equivalent capacity single core copper cable of conforming to relevant I.S. code (IS:7098-2) of reputed make like Havells, Polycab, V-Guard etc. for electrification of the pumping set. Complete Job includes cost of material , consumable, handling loading, unloading , transportation charge , labour charges for both skilled/semiskilled labour and hiring charges for crane , tripod stand , tools and tackles required during the execution of the job at site.

Vaibhav Engineers and Technocrates

GEETA ENGINEERING MECH WORKS