Balance work of canteen with stair at SKIMS.

Amount

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: ( In cement mortar)

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead :

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed:( All kinds of soil )

P/l of stone solling/boulders hand packed including all carriages upto site of work.

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. (In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete.)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: ( 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including all carriage.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : (Cement mortar 1:4 ( 1 cement : 4 coarse sand) including all carriage

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : ( Cement mortar 1:3 ( 1 cement : 3 coarse sand)

Extra for brick work in superstructure upto floor v-level.

Centering and shuttering including strutting, propping etc. and removal of form for: (Shelves (cast-in-situ)

Edge of slabs and breaks in floors and walls under 20 cm wide.

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with ( 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) including all carriage.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level (Thermo-Mechanically Treated bars of grade Fe-500D or more.)

15mm Cement plaster of mix:(1 : 4 ( 1 cement : 4 fine sand)

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels(Area of slab upto 0.5 sqm) granite of any color or shade 18 mm thick.

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. (Granite Work)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.

15 mm dia

20 mm dia

P/f of G.I union of approved make.

15 mm bore

20 mm bore

P/f of ball valve brass of approved make.

15 mm nominal bore

20 mm nominal bore

P/F of stainless steel sink IS 304 of size 610*510*200 of approved quality and manufacturer.

p/f of basin/wall mixer of approved make parko/jaquar or equivalent make

P/F of CP angle valve of approved make (Parko/Jaquar).

p/f of china ware washbasin of approved make hindware/cera or equivalent make 500*400 mm

p/f of china ware pedestal for washbasin of approved make like hindware,cera or equivalent make

p/f of flexible type waste pipe of approved make 32 mm dia.

p/f of PVC connection of approved make 18” long

p/f of CP soap case of approved make.

p/f of CP towel rings of approved make.

P/f of mirror of superior quality of approved brand and manufacturer.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (First class deodar wood) including cost of hold fasts.

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. (With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws) 35 mm thick

p/f of hardware fittings of approved make.

Tower bolts 150 mm

Handle 150 mm

Link lock rod type 11” long

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) powder coated aluminum.

For fixed portion

For shutters

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin- charge. (Cost of aluminum snap beading shall be paid in basic item.) (With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm)

P/f of 3.00 mm thick ACP sheet paneling in aluminium work including cost of rubber neoprene gaskets.

p/f of powder coated aluminium fittings of approved make.

Handle 150 mm

Hinges 125 mm

Link lock/Godrej

Tower bolts 100 mm

Handle 100 mm

P/l of PVC pipe prince or equivalent make B-class including rubber gaskets etc complete.

100 mm dia

75 mm dia

p/f of PVC fittings of approved quality and manufacturer(Prince or equivalent)

Plain bend 100 mm

Door tee 100 mm

Coalar 100 mm

Floor trap 100 mm

Plain bend 75 mm

Door tee 75 mm

Coalar 75 mm

Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in Horizontal/vertical or curved surface) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (0.63 mm thick with zinc coating not less than 275 gram/m2)

PARVEEZ AHMAD BHAT

M/S MIR INFRASTRUCTURES

MANZOOR AHMAD SHEIKH