Replacement of CI/GI pipe of different sizes and rewinding of motors and repair of pumps, replacement of startor and other misc items at Faridkot Mil Stn

Amount

(i) M&L disconnecting/dismantling and strip opening of worn out/ defective electric motor of any make and Capacity of 75/100 HP, 3 phase 415 volts AC supply, taking out burnt stator winding, servicing cleaning of stator slots, bearing, bushes etc rewinding of stator coils with superior quality of copper enamel wire of existing size and specification including insulating material, Varnishing, china glass paper,'F' class paper,Thick sheet paper ( packing sheet) and drying, and replacement of rusted nut bolts and washer,seal etc, assembling, testing installed and connected at original location complete all as specified and directed by Engineer-in-Charge:- i) Servicing and insulation of rotor assembly . (ii) Strip opening in spare parts and doing above mentioned job works through authorised locally available high skilled mechanic /Electrician at work shop.

All as per item No 01 here in before but of capacity 30 to 45 HP, 3 phase 415 volts AC supply complete all as specified and directed by Engineer in Charge.

All as per item No 01 here in before but of capacity 3 to 5 HP, 3 phase 415 volts AC supply complete all as specified and directed by Engineer in Charge.

All as per item No 01 here in before but of capacity 1 to 2 HP, 3 phase 415 volts AC supply complete all as specified and directed by Engineer in Charge.

M&L disconnecting/dismantling and strip opening defective,and overhauling of pumping set of any make and Capacity of 75/100 HP, taking out bearing, bushes, Impeller and coupling plates etc and Greasing of bearings with superior quality and replacement of brass bushes,MS flange coupling,tyre coupling,slip, impeller,rusted nut bolts and washer,seal etc and lath work on shaft including proper alignment and assembling, testing installed and connected at original location complete all as specified and directed with entire satisfaction of Engineer-in-Charge. NOTE if above parts is in well condition and no need to replace then contractor will provide these items to concern section.

All as per item No 05 here in before but of capacity 30 to 45 HP, complete all as specified and directed by Engineer in Charge.

All as per item No 05 here in before but of capacity 3 to 5 HP, complete all as specified and directed by Engineer in Charge.

All as per item No 05 here in before but of capacity 1 to 2 HP, complete all as specified and directed by Engineer in Charge.

S&F in replacement of 3 pole MCCB 63 Amps, 50 HZ, 415 Volts, 25 KA complete all as specified and directed.

S&F in replacement of 3 pole MCCB 100 Amps, 50 HZ, 415 Volts, 25 KA complete all as specified and directed.

S&F in replacement of 3 pole MCCB 200 Amps, 50 HZ, 415 Volts, 25 KA complete all as specified and directed.

S & F in repair Star Delta Starter fully automatic suitable for 12.5 HP, 415 volts complete all as specified and directed.

S & F in repair Star Delta Starter fully automatic suitable for 15 HP, 415 volts complete all as specified and directed.

S & F in repair Star Delta Starter fully automatic suitable for 30 HP, 415 volts complete all as specified and directed.

S & F in repair Star Delta Starter fully automatic suitable for 50 HP, 415 volts complete all as specified and directed.

S & F in repair Star Delta Starter fully automatic suitable for 75 HP, 415 volts complete all as specified and directed.

S & F in repair Star Delta Starter fully automatic suitable for 125 HP, 415 volts complete all as specified and directed.

S & F Single phase preventer for any capacity of motors complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair Digital soft starter suitable for 100 HP 3 phase centrifugal pump specially used in heavy duty applications XLP8 Adaptive acceleration feature ,comprehensive motor protection ,built in RTD and thermister inputs 99 event logs with time stamping power through operation to run soft starter even if 1 analog output fully programmable overload trip,real time metering and monitoring ,kickstart constant current ,forward /reverse jog large LCD KEYPAD,2 motor data set,control voltage from 94 VAC to 480 VAC ,Starter communication timeout,I/O expansion card (optional) as directed and specified by engineer in charge. Make : L & T, Havells

S&F in replacement of sluice valve class PN-1.6 14846 ISI marked with brass spindle, flanged end of size 300mm bore including joint with rubber or fiber board gasket, nut bolts washers as per existing specification and body shape complete all as specified & directed by Engineer-in-Charge..

S&F in replacement of sluice valve class PN-1.6, IS 14846 marked with brass spindle, flanged end of size 250 mm bore including joint with rubber or fiber board gasket, nut bolts washers as per existing specification and body shape complete all as specified & directed by Engineer-in-Charge.

S&F in replacement of sluice valve class PN-1.6, IS 14846 marked with brass spindle, flanged end of size 200mm bore including joint with rubber or fiber board gasket, nut bolts washers as per existing specification and body shape complete all as specified & directed by Engineer-in-Charge.

S&F in replacement of sluice valve class PN-1.6, IS 14846 with brass spindle, flanged end of size 150mm bore including joint with rubber or fiber board gasket, nut bolts washers as per existing specification and body shape for Over Head tanks inlet & outlet pipes complete all as specified & directed by Engineer-in-Charge.

S&F in replacement of sluice valve class PN-1.6, IS 14846 with brass spindle, flanged end of size 100mm bore including joint with rubber or fiber board gasket, nut bolts washers as per existing specification and body shape for Over Head tanks inlet & outlet pipes complete all as specified & directed by Engineer-in-Charge.

S&F in replacement of sluice valve class PN-1.6, IS 14846 with brass spindle, flanged end of size 80mm bore including joint with rubber or fiber board gasket, nut bolts washers as per existing specification and body shape for Over Head tanks inlet & outlet pipes complete all as specified & directed by Engineer-in-Charge.

S&F in replalcement of Non Return Valve PN 1.6 (Reflux valve) flanged end with by pass charged conforming to IS 5312, ISI marked supplied and installed complete of size 300mm dia flanged end ISI Marked with all fittings complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in kerbs/coping/bed plates and the likes including weathering, slightly rounded or champhered angles with necessary use and waste of formwork for pipe support , finishing even and smooth without using extra cement , complete all as specified and directed by Engineer-in-Charge..

Taking up or down GI Water mains inculding all fitting of 15 mm bore complete all as specified and directed by Engineer-in-charge

All as per Item No 28 here-in-before but 20 mm bore complete all as specified and directed by Engineer-in-charge.

All as per Item No 28 here-in-before but 25 mm bore complete all as specified and directed by Engineer-in-charge.

All as per Item No 28 here-in-before but 40 mm bore complete all as specified and directed by Engineer-in-charge.

All as per Item No 28 here-in-before but 50 mm bore complete all as specified and directed by Engineer-in-charge.

Taking up or down cast iron water mains inculding all fitting with spigot or socket ends and lead joints including burning out joints and removing lead for 80/100 mm bore pipes complete all as specified and directed by Engineer -in-charge.

All as per Item No 33 here-in-before but 200 mm bore complete all as specified and directed by Engineer-in-charge.

All as per Item No 33 here-in-before but 300 mm bore complete all as specified and directed by Engineer-in-charge.

M&L for CI fitting for spigot & socket pipes, bends, tapers tee pieces ,caps & plugs up to 300 mm bore of pipe complete all as specified and directed by Engineer-in-charge.

M & L for Steel water tubing medium grade galvanised with all fitting laid in trenches/ fixed to wall etc of size 15 mm bore complete all as specified and directed by Engineer-in-charge.

All as per Item No 37 here-in-before but 20 mm bore complete all as specified and directed by Engineer-in-charge.

All as per Item No 37 here-in-before but 25 mm bore complete all as specified and directed by Engineer-in-charge.

All as per Item No 37 here-in-before but 40 mm bore complete all as specified and directed by Engineer-in-charge.

All as per Item No 37 here-in-before but 50 mm bore complete all as specified and directed by Engineer-in-charge.

M & L forDismantling existing lead joint and providing new run lead joint using old retrieved lead & adding additional lead as reqd at site for 80 mm bore of pipe, complete all as specified and directed by Engineer-in-charge.

All as per Item No 42 here-in-before but 100 mm bore of pipe complete all as specified and directed by Engineer-in-charge.

All as per Item No 42 here-in-before but 300 mm bore of pipe complete all as specified and directed by Engineer-in-charge.

S & F in repair Gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe & fixed 50 mm dai of pipe complete all as specified and directed by Engineer-in-charge.

S & F in repair Gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe & fixed 40 mm dai of pipe complete all as specified and directed by Engineer-in-charge.

S & F in repair Gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe & fixed 25 mm dai of pipe complete all as specified and directed by Engineer-in-charge.

S & F in repair Gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe & fixed 20 mm dai of pipe complete all as specified and directed by Engineer-in-charge.

S & F in repair Gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe & fixed 15 mm dai of pipe complete all as specified and directed by Engineer-in-charge.

Excavation in trenches n.exc 1.5 mtr width & n.exc 1.5 mtr in depth for foundation/pipe lines etc and getting out in soft/loose soil complete all as specified and directed by Engineer-in-charge.

Returning filling in including spreading leveling watering & and well ramming in layers n.exc 25 cm in soft/loose soil complete all as specified and directed by Engineer-in-charge.

Removing excavated material n.exc 50 mtr & depositing where directed at a level n.exc 1.5 mtr above the starting pointing complete all as specified and directed by Engineer-in-charge

S & F in replacement 50 mm bore cast iron air release valve flanged type with two air out lets and Including jointing material , such as nuts, bolts, washers and rubber sheet etc.complete all as specified and directed by Engr-in-charge.

Supply and laying CI Pipes of size 80mm with spigot and socket ends centrifugally cast, class LA in any trenches as directed and specified by Engineer in charge.

Supply, laying, jointing, commissioning and testing Ductile Iron pipes 100mm bore with spigot and socket and centrifugally cast (Spun) Class K-9 conforming to IS-8329-2000 in any length with & including rubber push (Tyton) joint laid in trenches complete all as specified and directed by Engineer in Charge.

Supply, laying, jointing, commissioning and testing Ductile Iron pipes 200mm bore with spigot and socket and centrifugally cast (Spun) Class K-9 conforming to IS-8329-2000 in any length with & including rubber push (Tyton) joint laid in trenches complete all as specified and directed by Engineer in Charge.

Supply, laying, jointing, commissioning and testing Ductile Iron pipes 300mm bore with spigot and socket and centrifugally cast (Spun) Class K-9 conforming to IS-8329-2000 in any length with & including rubber push (Tyton) joint laid in trenches complete all as specified and directed by Engineer in Charge. Note for Srl item No. 55 to 57 : Fittings, Excavation and earth work will measured and paid for separately under respective item of BOQ Note :- A Sum of Rs. 1,34,054.00 will be deducted on account of credit for dismantling/demolished/taking down material. Please refer detail on srl page No 22 (Schedule of credit) of Tender Documents.

DIAMOND ELECTRICALS

M/S RAJESH KUMAR and CO.

BHARAT BHUSHAN CONTRACTOR

POOJA CONSTRUCTION COMPANY

DEEPAK ENTERPRISES