SPL REPAIR TO OR MD ACCN BLDG NO P-21/01 TO P-21/08 AT NIRMAN ENCLAVE AND OTHER SANCTIONED WORKS AT NAMS

Amount

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) all as specified and directed.

Taking down unserviceable chowkhats or frame with shutters(without taking off shuters from the frames) of any description n. exc 1.50Sqm and removing from site and making good disturbed surfaces of wall in CM 1:3 complete all as specified & directed.

M&L 35mm thick factory made solid PVC (Wood plastic composite ) moulded gauged door shutter with wire mesh 0.18mm nominal dia of wire and average width of apreture 1.40mm in any number of division with brown wood grain texture , including TN aluminium mess for additional strength and safety purpose (confirming as per IS 4020) shall be fixed with 15x15 square tubes in is rails with screwing 8x28mm heat metal Zink coated screws can be remove or fix again after changing of wire mesh when needed . The density shall be as per manufactures instructions complete all as specified and directed

M&L Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door frames/ Chowkhat of size 50x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant complete all as speicifed and directed.

All as per ser item No 5.00 above but of frame size 65x125 including all fitting making good after complete all as speicifed and directed.

Material & labour for box type steel window 1.25 mm thick made of ERW tube P-Section of size 60 x 25 mm double rebated outer frame comprise of glazed skeleton shutter(two gauged shutters and two glazed shutter) of ERW tube P-Section size 50 x 20 mm and 1mm thick one/two Nos openable leaf consisting of two Nos sash bar of T-Section 20x3mm welded to frame with one No Vertical mullion of ERW box type T-Section of size 60 x 25 mm and 1.25 mm thick and FI 2 mm thick welded / screwed to frame for fixing of glass including fittings and fixture like Handle, Tower Bolt, stopper, cleat, pintal hinges, hold fast etc including provn of cooler/AC opening etc. (a) Hold Fast, 150mm long of 120mm x 3 mm made to shape -04 Nos per window. (b) Handle of Z sec 20mm x 25mm, 100 mm long -1 No per leaf (c) MS Tower bolt 150mm long - 2 No per leaf (d) Z Sec 20mm x 25 mm, 100 mm long stopper - 1 No per leaf (e) Cleat 55 mm long of hollow square 15mm x 20mm x.63mm welded to hinge -1 No per leaf. (f) MS Pintal hinges of size 75mm x 12mm - 2 Nos per leaf (g) 12 mm square guard bar, 10 cm centre to centre. (h) 25x4 mm flat iron all around for joint of both frame. (j) One shop coat of red oxide primer and two coats of Synthetic enamel paint to MS window and guard bar Note: (i) Including taking down old steel window/ ventilator and making good dismantled portion with PCC 1:2:4 type B0 including hold fast PCC (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finishing complete all as specified and directed by Engineer-in-charge. (ii) sheet glass and wire mesh shall be measured and paid separately)

Material & labour for box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame (single rebated ) of ERW and FI 2mm thick welded /screwed to frame for fixing of sheet glass including fixtures and fittings like a stopper , cleat , pintal hinges , holdfast etc all as shown on drg No CEJZ/TD/1019/08 sheet 1/3 to 3/3 dt 01 May 2008 complete all as specified. (a) 10mm Sq Guard bar 10cm C/C.v(b) One shop coat of red oxide and two coats of synthetic enamel paint to MS ventilator and gaurd bar (c) MS Tower bolt 150mm long - 2 No per leaf (d) Z Sec 20mm x 25 mm, 100 mm long stopper - 1 No per leaf Note: (i) Including taking down old steel ventilator and making good dismantled portion with PCC 1:2:4 type B0 including hold fast PCC (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finishing complete all as specified and directed by Engineer-in-charge. (ii) sheet glass and wire mesh shall be measured and paid separately)

S&F Sheet glass, 3mm thick ordinary quality, in squares, not exceeding 0.50 sqm in each pane fix with oil putty complete all as specified and directed. (Note upto four storey height including all scaffolding work )

S&F GI wire cloth, 0.36 mm nominal dia. of wire and average width of aperture 1.4 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed

S&F in repair 3mm thick figured/ froasted glass, pin head type and glazing with oil putty in squares nexc 0.5 sq. m in each pane etc complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.40mm and fixed tinned or stainless steel wire staple complete all as specified and directed.

S&F Stainles steel butt hinges 100mm long medium weight fixed complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S & F aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed.

S&F Aluminium door stopper double support with rubber complete all as specified and directed.

S&F aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 300 mm long complete all as specified and directed.

Taking down cement plaster on Brick/concrete surface etc including racking out of joints hacking for keys scrubbing down with water

M&L for 15 mm thick rendering in cement mortar (1:6) on fair face of brick or concrete surface finished even and fair (without using extra cement)all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:4) on fair face of brick or concrete surface finished even and fair (without using extra cement) all as specified and directed. Note: Rate applicable upto four story high bldg incl necessary scaffolding etc.

M&L, rendering 10mm thick in CM 1:3 over concrete surface as on ceiling finish even and smooth w/o using extra cement (without using extra cement) , complete all as specified and directed.

M&L for damproofing to wall with two components Acrylic polymer cementitious water proof elastomeric coating for grade mix to form uniform slurry and apply with paint brush as first coat then laying a layer of fibre glass mesh cloth as first coat is still green with overlap of joints of fibre mesh not less than 100 mm, then finally apply second layer mix by brush to entire surface of container covering 0.6 - 0.75 Sqm /Kg including 15mm thick rendering in cement mortar (1:4) fair faces of brick / stone masonary surfaces, finished even and smooth without using extra cement, complete all as specified and directed. Note : Quoted rate shall be deemed to be inclusive of materials all labours, tools and plants, scaffolding and working upto height 6 metre etc.

M&L preparation of new plastered surface applying 1mm thickness putty and two coat of oil bound distemper complete all as specified and directed

M&L preparation of new plastered surface applying a coat of primer and two coat of Acrylic emulsion paint complete all as specified and directed

M&L Prepration of new plastered surface and applying 3 coat of white wash on ceiling complete all as specified and directed

M&L for preparation of old decorated plaster or un- plastered surfaces and providing two coat of white wash on ceiling etc, complete all as specified and directed.

M&L for complete removal of existing treatment of old plastered surface of wall and applying two coat of oil bound distemper over a coat of 1mm thick wall care putty, complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description over 10cm width or girth & applying one coat of synthetic enamel paint of approved quality, tint to achieve glossy finish, complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth & applying one coat of synthetic enamel paint of approved quality, tint to achieve glossy finish, complete all as specified and directed.

Supply only liquid WPC complete all as specified.

Dismantling floor, hearth or wall tiles, including cement mortar, removing serviceable tiles from site & rubbish off the premises, complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in floors etc. laid over 15mm thick screed bed in cement mortar 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 18 sqm but not exceeding 0.36 sqm, in floors etc. laid over 15mm thick screed bed in cement mortar 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 18 sqm but not exceeding 0.36 sqm, in skirting/ddado etc.including rendering 10 mm thick in cement mortar 1:4 and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed.

M&L for Glazed ceramic coloured tiles of size 300mm x 450 mm x 7mm thick including providing highlighter/ any pattern on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or white cement cement mixed with colour pigments to match the shade of tiles including rendering 10mm thick in cement mortar (1:4) complete all as specified and directed.

Material and labour for 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded aggregate as in floors including finishing the surface rough & even for receiving kota/tiles complete all as specified and directed.

Dismantling and taking down water storage tanks of 500 Ltr capaciaty and S&F 500 ltrs capacity rotatonal moulded polyethylene water storage tanks Triple layer in white colour (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including S&F of ball brass valve high pressure of 20mm dia complete all as specified and directed.

S&F in repair Bib tap CP fancy type/long body 15 mm bore with will crutch or buttewrfly handle screwed down screwed to iron pipe complete with all fittings complete all as specified and directed.

Supplying and fixing in repairs cast copper alloy chromium plated wall mixer 3-in-1 system with complete provision and fixing for Overhead Shower with 115 mm Long Bend pipe, CP screwed down high pressure with long screwed both ends for 15mm dia bore GI pipe of approved make as per sample complete all as specified and directed.

S&F in repair Angle cock CP fancy type 15 mm bore screwed down high pressure with crutch or butterfly handle & screw both end for iron pipe or for Unions complete all as specified and directed.

S&F in repair brass chromium plated shower rose with Arm length not less than 150mm swivel joints size 125mm with arm fixing to steel pipe or union complete all as specified & directed

S&F in repair tubular towel rail 600mm long, 20mm dia 'D' type CP rail with fixed in wall complete all as directed

S&F in repair Pillar tap CP fancy type/long body 15 mm bore with will crutch or buttewrfly handle screwed down screwed to iron pipe complete with all fittings all as specified and directed.

S&F in repair 10 ltr capacity low levels flushing cistern with PVC bend and PVC flush down pipe etc complete all as specified and directed.

S&F in repair for viterous china squating pan of (Orrissa Pattern) size 580 x 440 white with 'P' or 'S' trap front or back inlet and integral foot rest , including joining, filling and provision of cement concrete bedding 1:5:10, type E2 (excluding flushing cisteern and flush pipe) fixed incl cement concrete bedding as required set complete all as specified and directed.

S&F in repair, Vitreous China corner Wash Hand Basin, white, size 315 x 315 x 160 mm including brass coupling, mild steel brackets fixed to wall with pedestal etc. complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Supply and fix in repair, PVC Bath Cabinet made from hard thermosetting material with mirror, white/ivory colour, 400 x 500mm size complete all as specified and directed.

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm without drainage board, with plugs, washers and waste including fixing cantilever brackets complete all as specified and directed.

S&F stainless steel plate rack overall size 90 x 75 X 25 cm made out of 0.63mm thick steel sheet as per standard pattern fixing to walls with screwed complete all as specified.

S&F PVC waste pipe 32mm bore including socket complete all as specified and directed.

Dismantling boarding any description fixed in any position with nailsv complete all as specified and directed.

Supply & fix 18 mm thick, PVC sheet one side prelaminated of approved texture ("Celuca ply of Rajshree make or equivalent as in Kitchen cabinet, cub board (with shelves and partitions) including necessary fitting & fixture as per manuacturer's instructions complete all as specified and directed.

S&F 125 mm dia oval shape brass handle fancy type bright finish complete all as specified & directed.

S & F 75 mm long Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Supply and fix 30 mm wide continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

M&L Green marble work 18 to 20mm thick (table rubbed and polished) laid over 15 mm thick screed bed of CM 1:6 as in flooring and jointed with grey cement slurry mixed with pigment to match the shade, rubbing & polishing complete all as specified and directed.

S&F in repair mild steel powder coated curtain rods 20mm dia of approved quality incl bracket, knobs etc complete all as specified as directed.

S&F in repars 15mm bore stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed.

All as per ser item No 59.00 above but size 20mm bore complete all as specified and directed.

Taking up or down steel tubing 15mm bore pipe and connection removing the same from site/keeping aside for reuse complete all as specified and directed.

All as per ser item No 61.00 above but size 20mm bore pipe complete all as specified and directed.

S&F GI tubing 15mm bore pipe medium grade including all fittings fixed to walls and ceilings or laid in floors complete all as specified and directed.

All as per ser item No 63.00 above but size 20mm bore pipe complete all as specified and directed.

Demolition of brick work built in cement mortar complete all as specified and directed.

M&L for brick work using sub class ‘B’ bricks, straight or corved on plan exc. 6 mean radius in CM 1:6 complete all as specified and directed.

All as per ser item No 66.00 above but except brick complete all as specified and directed.

M&L for brick work using sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

Dismantling brick tiles or terraling tiles single layer as in roofing complete all as specified and directed.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) and dispose from site exc 500 mtr complete all as specified.

M & L for 50mm avarage thickness PCC 1:2:4 type B1 (using 20 mm graded stone aggregate as roof padding , sub base floor, even and smooth without using extra cement for further treatment complete all as specified and directed.

M&L for preparation of roof surface & applying evenly a tack coat of industrial bitumen primer 85/25 grade @ 1.2 Kg/Sqm including APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced wih polyster non wove fabric (wt not less than 150 gms/sqm) applied on primed surface by forced application of heat and roller, joints to be touched hot and width of overlaps not be less than 150 mm complete all as specified and directed.

Material and labour for 40 mm thick brick tiles laid over and including 25 mm screed bead in CM 1:4 and joints grouted flush in CM 1:3 mixed with 5% of crued oil by weight of cement, complete all as specified and directed.

All as per ser item No 73.00 above here-in-before but exept brick tiles complete all as specified and directed.

S&F PVC (SWR) bend 110 mm with access door complete all as specified and directed.

S&F stack clamp out of 50mmx5mm flat iron and 16mm dia round iron stay including bolts and nuts and securing end of stay to wall or roof 100mm all as spicefied and directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors and wall complete all as specified and directed.

M&L for 110mm bore of pipe PCC 1:4:8 type D-2 concrete bed to drain pipes including packing under and hauching against the sides of pipes after they are laid complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single (Single T) equal or unequal complete all as specified and directed.

M&L for PVC(SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 75mm complete all as specified and directed.

M&L for 110mm bore PVC Gully Trap setting / jointed with solvent cement complete all as specified and directed.

S&F PVC(SWR) vent cowl 110mm dia complete all as specified and directed.

S & F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with oval access door complete all as specified and directed

S&F in repairs 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 75mm bore PVC(SWR) bends with oval access door of any radius complete all as specified and directed.

M & L for rolled mild steel work angle iron as in door frame/ cooler stand / water tank stand and other similar work confirming to Fe-290 complete all as specified and directed.

M&L for 1.25 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Demolition of cement concrete (unreinforeced) in ground floors and pavings n. exc 15cm thickness (below or above ground level).

M&L PCC (1:3:6) type C-1 using 20mm graded stone aggregate, 75 mm thick as in plinth protection finished fair & even in alternative bays n. exc 2M in length and joints filled with butmen mastic 1:3 (1 Bitumen : 3 Sand) complete all as specified and directed.

M & L for repair to RCC Chajjas, roof projection edges ,hanging part of chajjas, edges of chajjas, RCC parapets, under the roof / floor slabs with PCC 1:2:4 (using 12.5mm crushed graded agg) incl neccasary renforcement 8mm to 12mm TMT bars , form work , MS wire mesh for bounding the concrete on ground required and plaster work in CM 1:3 & periodical services to match with the existing surfaces finishing at any height of buildings etc completed all as specified and directed.

Demolition of cement concrete as in sunken floor of bath,wc and kitchen of any description and any position not otherwise specifically provided complete all as specified and directed.

Material and labour for Water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WC's etc shall be as under :- (a) Application of Two component Acrylic modified cementitious coating (i) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance, existing coatings and achieve a gripping profile that is clean, dry and free from laitance and any other form of surface contamination. The installation instructions in manufacturer’s published literature should be strictly complied with, including but not limited to the following :- (ii) Chipping out any visible cracks in “V-Groove” pattern as applicable. Special attention on this part. Cleaning of cracks & then filling those cracks with SIKA latex SBR 100 putty/ Dr Fixit 302 SBR latex / Perma latex SBR / FOSROC Nitabond SBR latex / Asian Paints latex as required. Final cleaning of surface with power grinder, wire brush, hair brush & vacuum pressure if required. (iii) Dampen all surfaces immediately ahead of application of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO.

(iv) Whilst the surface is still damp from saturation (S.S.D), apply one coat of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO of viscosity as per manufacturer’s instructions. (v) Apply Glass Fabric Sheet of Sika Fab 1 / FOSROC/ Dr Fixit/ STP whilst the first coat is wet. (vi) Once touch dry, apply second coat of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO of viscosity as per manufacturer’s instructions on the entire area. (vii) Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat. (viii) The waterproofing coating should be taken to a height minimum 300 mm above the finished floor level on the vertical surface. (ix) It is essential to cure Acrylic modified Cementitious coating immediately after application (minimum 6-8 Hrs drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking. (x) A protection plaster (12-15mm thick) in CM 1:3 admixed with appropriate Integral water proofing compound has to be applied on the walls. Admixture : Sika Plastocrete Plus / FOSROC / Dr Fixit / STP / CICO confirming to IS 2645. Providing and applying a protection screed of 50mm thick 1:4, cement sand mortar admixed with Sika Plastocrete over the applied water proofing coating on horizontal surfaces.

(xi) All the corners and joints should be pre-treated with an elastic waterproofing sealing tape with a Woven bonding mesh on each surface and an elastic expansions zone in the centre of Make Sika Seal Tape S/FOSROC/Dr Fixit/STP. (xii) The membrane has to be protected in accordance with the manufacturer’s recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer’s recommendations (xiii) Waterproofing treatment has to be carried out through applicators authorised (b) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealant. (c) Al CI traps in sunken slabs to be enclosed with PCC 1:1.5:3 (min 15cm) All-round. (d) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40mm stone aggregate) complete all as specified (e) Providing drainage spout pipe GI 40 mm dia bore light grade upto outside of outer wall (Approx 450 mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed. (f) Providing 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified. Note: Items No 93.02 (d), (e) & (f) shall be measured and paid separately.

M&L cement concrete in mass concrete type F2 1:7:12 (40mm graded agg) as in sunken floor complete all as specified and directed.

S&F drainage spout pipe GI 40 mm dia bore light grade upto outside of outer wall (Approx 450 mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed.

M & L for 75 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone agg as in sub base etc complete all as specified and directed.

M & L 60mm thick Machine pressed precast concrete coloured interlocking paver block any shape and size confirming to IS 15658-2006 , M-35 grade of required size/ shape with grey cement wth no pigment laid over and including 50mm thick compacted bed of fine sand, etc complete all as specified and directed.

M & L glazed and coloured chequered tiles of size 300 x 300 x 25 mm thick laid over 15 mm thick screed bed in CM 1:6 bedded and jointed in neat cement slurry, incl dismantiling of stone slab and tiles of any discription or thickness in floors / aprons etc complete all as specified and directed.

Excavation in trenches in soft/loose soil not exc 1.5 m wide and not exceeding 1.5 mtr in depth for foundation etc shaft, cesspits, manholes, pipe lines etc not exc. 10 sqm on plan and getting out complete all as specified & directed.

Demolition and breaking of 150mm bore drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed

M&L for PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate ) bed to pipes including packing under and hauching against the sides of pipes and tested for bore 150 mm pipes complete all as specified and directed.

S&F 150mm dia salt glazed stone ware drain pipe laid in trenches and jointed in cement mortar all as specified.

Returning filling in including spreading levelling watering and well ramming in layers n exc 25 cm thick complete all as specified and directed

Removing Excavated soils exceeding 250 M but not exceeding 500M and depositing where directed.

Material and Labour cement concrete 1:3:6 type C-2, using 40 graded stone aggregate, as in surface channel and drain and similar work incl demolition complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends complete all as specified and directed.

M & L for Add or deduct for each 25 mm girth or part thereof over or under 30cm complete all as specified and directed.

M&L for precast reinforced Cement concrete nominal mix 1:1.5:3 type B- 1 (using 20mm graded stone aggregates) in cover slab for manhole , drain and connected works type B- 1 (using 20mm graded stone aggregates) complete all as specified and directed.

S&F mild steel TMT bars 10mm dia.and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. Or securing with clips complete all as specified and directed

Material and labour for 300mm dia reinforced concrete pipes class NP-2 laid amd jointed including collar and demolition of old pipes complete all as specified and directed

M&L for PCC (1:3:6) type C-2 using 40mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 300 mm bore complete all as specified and directed.

Demolition and breaking up drain pipes of 150mm internal dia of bore SGSW, AC or reinforced concrete pipe set in cement mortar complete all as specified.

M&L for 150 mm bore dia Reinforced concrete pipes Class NP 3 pipes laid and jointed with collar complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in cills, PCC blocks, coping, haunching and benching bed plates, seismic and other similar bands, plinth bends, etc including weathering slightly rounded or chamfered angles and throuting, inclusing necessary form work etc complete all as specified and directed

M&L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete/ sub base of floors etc including demolition of existing PCC complete all as specified and directed.

S&F mild steel Gde Fe-410-W Gde E-250 quality A as in roof trusses, (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee,angle,channel or flat sections) including distance pieces , cleats etc complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished ,and reforming benching as required for 150 mm internal dia of pipe complete all as specified and directed.

Taking down aluminium/copper point wiring from existing conduit / batten (light, fan, socket or power) complete such as switches, ceiling rose, pendent, regulators, socket, light fittings etc and removing material from site and making good the disturbed surface of wall / floor etc, complete all as specified and directed.

M&L for point wiring with 1.5 sqmm (Nominal area ) 1100 Volt PVC Insulated , FRLS unsheathed and multi stranded copper conductor cable in and including new PVC Concealed conduit 20mm dia (1mm thick) for one light / fan point or bell point controlled by one switch (including cutting chases and making good the distributed surfaces) and fixing new 3mm thick plastic laminated sheet top cover, sheet screws and 1.6mm thick GI sunken boxes after removing old unserviceable plastic laminated sheeet and sunken boxes included 1.5 Sqmm stranded copper conductor with green PVC Insulation earth contunity conductor connected to common earth dolly etc complete all as specified and directed Note : The cost of sunken boxes and bakellite sheet is included in the quoted rate.

One light /bell point /Fan point / Exhaust fan point controlled by one 5 amp switch one way complete all as specified and directed.

All as per ser item No 121.00 above but for one 5 amps independent Board complete all as specified and directed.

All as per ser item No 121.00 above but on the same board complete all as specified and directed.

All a per item No 121.00 above but with 2.5 Sq mm size cable multi stranded FRLS copper wire unsheathed for one 3 pin socket outlet 15 Amps on independent board including continuous earth wire of PVC insulated 1.5 Sq mm copper solid conductor connecting to common earth dolly complete all as specified and directed.

Supply and fixing of switch piano type 6 Amps one way 230 volts AC complete all as specified and directed.

Supply and Fixing of socket outlet 5 pin, 6 Amps flush type 230 volts AC complete all as specified and directed

Supply and Fixing of switch piano 16 Amps type one way 230 volts AC complete all as specified and directed

Supply and Fixing of socket outlet 6 pin 6/16 Amps multi purpose flush type 230 volts AC complete all as specified and directed

Supply and Fixing of switch type regulator 5 step 230 volts AC complete all as specified and directed

Supply and fixing of ceiling rose 65/50 mm two to three terminals complete all as specified and directed.

Supply and fix of MCB 40 Amps single pole with neutral, AC 230 Volts complete all as specified and directed.

Supply and fix of MCBs single pole (SP) 5 to 32 Amps with 10 KA breaking capacity of 'B' series in distribution boards complete all as specified and directed.

Supply and fixing in replacement Sheet metal enclosure for DB's when MCB's to be used double door factory made flush fixed complete with 200 Amps rated busbar 240 Volts single phase 8 ways complete all as specified and directed.

Supply and fix in replacement for sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area 6.0 Sqmm drawing into and including PVC non metallic rigid conduit medium grade of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 6.0 Sqmm as a earth continuity conductor(green colour) and including non metallic medium grade rigid PVC conduit, including cutting chases in brick wall, and making good to match the existing specifications complete all as specified and directed. Note : (i) Rates are deemed to be included cutting and making holes in wall/floor for passing in or through conduit. (ii) Two run of 6.00 sqmm single core (FRLS) PVC insulated copper conductor cable, one run of 6.0 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of suitable size will be measured as a one unit.

All as per ser item No 132.00 above but for 4.0 sqmm complete all as specified and directed.

Material and labour of lamp holder insulated body with 9 Watt LED Bulb, back plate batten/angle type for batten fitting fixed on bakelite sheet 100mmx100mm 230V AC cool day light 6500K having maximum height 1020 mm heavy duty complete all as specified and directed.

Supply and fixing in replacement of sheet steel enclouser distribution boards, double door factory made TPN Vertical 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB and 12 outgoing MCBs circuits comprising of 3 phase 4 wire of suitable rating complete all as spcd and directed with the following accessories :- (a) MCCB 100 amps, 25 KA, TP, 415 volts, 50 Hz = 01 No. (Note:- Out going MCB shall be measured and paid for separately)

Supply and fix exhaust fan, steel body single phase 230V of size 300 mm sweep with blades, frame and louvers complete all as specified and directed.

Supply and fixing of LED T-8 tube light fitting with single side connection LED tube rod 18/20 W, 4 Feet made of CRCA sheet steel box type including bipin holder and connection with PVC insulated twin core 23/0.0076 ywisted copper cable from ceiling rode to light fitting complete all as specified and directed.

Supply & fix LED Street Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens complete all as specified and directed.

Supply and fixing of security light mounting bracket made out of GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat of size 40 x 6 mm and nuts and bolts and painting with aluminium paint, complete all as specified and directed.

Supply, laying in trenches or wall and testing in replacement of cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sqmm 4 core complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade ) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PART 1 , with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switche, DBs) complete all as specified & testing on completion.

Supply, laying & fixing in replacement double wall corrugated (DWC) pipes made of high density polythyline (HDPE) with all accessories i.e. all type of joints, Sockets, Elbows, bends and End caps of size 63mm outer dia and 50 mm inner dia etc complete all as specified and directed.

Supply and lay on wall/ floor etc GI pipe light grade of dia 32 mm for protection of cable complete all as specified and directed.

Taking down ceiling fan/geyser/exhaust fan in situ and refixing after servicing, repairing and painting them, scratching old paint and preparation of surface for painting with one coat of white / grey enmeled paint and including cable from ceiling rose to fan complete all as specified and as directed.

S & F in replacement of single pole and neutral sheet metal enclosures with two pin & earth plug and socket complete with one single pole MCB of 20 amps complete all as specified and as directed.

Supply and fixing in replacement of bell push 6 amps one way 230 volts AC complete all as specified and directed.

Supply and fixing in replacement of bell ding dong AC 230 volts complete all as specified and as directed.

Supply and fixing in replacement pvc connection of size 600 mm length 15 mm dia complete all as specified and as directed

Supply and fixing BLDC (Brushless direct current motor) ceiling fan 1200mm sweep copper winding low power consumption,high speed Aliminium body with blade, double ball bearing having minimum air delivery 220 CMM and BEE 5 star rated including acessories, connector, down rod etc complete all as specified and directed.

S & F in replacement of LED bulk head light fittings 10 watt white including LED strip as per IP 65 in engineering plastic housing with clear primatic diffuserand making necessary connection complete all as specified and directed.

Supply and laying of GI steel tubing 50mm bore medium grade with fittings laid in tranches/ wall/ floor and joined including necessary fittings such as bends, elbow, tees, sockets, reducer etc including necessary saddles and clamps complete all as specified and directed.

All as per ser item No 151.00 above but size 25 mm bore complete all as specified and directed.

Supply and fix Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of size 50 mm complete all as specified and directed.

All as per ser item No 153.00 above but size 25 mm complete all as specified and directed.

M&L for cutting of existing pipe line any type including insertion of new Tee any type and connection of 50/80 mm dia GI pipe complete all as specified and directed.

M&L for brick masonry valve pit of size 120 x 120 x 120 cm (internal size) with mild steel cover 6mm thick and angle iron frame of size 50mm x 50mm x 6mm duly painted with two coats of synthetic enameled paint over a coat of red oxide primer including locking arrangement, brick work and all inner surfaces of pit and exposed portion of out side shall be plastered in CM (1:4) complete all as specified and directed.

M/s Vijay Construction Co. (BID ID -3504558)