PROVISION OF CERTAIN NEW IGLOO SHEDS (PHASE-I) AT AFS AMLA

Amount

Blank

Blank

Blank

Blank

Blank

Blank

Blank

Blank

SCH 'A' PART X (MISC B/R & E/M ITEMS) Note:- Excavation and earthwork to the extent required for execution of relevant item under this schedule unless otherwise specified shall be measured and paid under relevant items of Schedule 'A' Part-II.

Supply and fixing hazard division symbol double sided board of size 1500 x 1500 mm by using double legged informatory sign board fixed on single frame and meeting back to back on the square pipe, boards of high intensity Green/blue or in colour as required by using retro-reflective sheeting of AVERY DENNISON made out of 2 mm thick Alco bond/ aluminium sheet conforming to IS 736 to be covered with high intensity grade retro-reflective sheeting (AVERY DENNISON) of Green/Blue or required colour as per user complete all as specified and as directed.

NOTES :- (i) The computerized cut AVERY DENNINSON sheet shall be fixed with suitable adhesive to alco bond/ aluminium sheet painted with epoxy paint to standard make, fixed to structural steel frame work of MS pipe of size 35 x 35mm square pipe with nuts, bolt/rivets ensuring safety against removal of plates. (ii) The lettering shall be computerised cut of high intensity grade white sheeting (AVERY DENNISON) and mechanically fixed on this board of Green/Blue colour or required color. Then these two separate boards shall be fixed back to back on single frame to two vertical posts of 50mm square pipe 2.5 mtr long to be painted in black and white alternative bands of 25cm height with synthetic enamel paint complete in all respect. (iii) This board on single frame shall be embedded in PCC 1:4:8, type D2 of required size including necessary excavation in post hole all as specified and as directed.

Supply and fixing double legged informatory sign board single side of size 1200 x 1200 mm, fixed on single frame and meeting back to back on the square pipe, board of high intensity Green/blue or in colour as required by using retro-reflective sheeting of AVERY DENNISON made out of 2 mm thick Alco bond/ aluminium sheet conforming to IS 736 to be covered with high intensity grade retro-reflective sheeting (AVERY DENNINSON) of Green/Blue or required colour as per user complete all as specified and as directed.

NOTES :- (i) The computerized cut AVERY DENNINSON sheet shall be fixed with suitable adhesive to Alco bond/aluminium sheet painted with epoxy paint to standard make, fixed to structural steel frame work of MS pipe of size 35 x 35mm square pipe with nuts, bolt/rivets ensuring safety against removal of plates. (ii) The lettering shall be computerised cut of high intensity grade white sheeting (AVERY DENNISON) and mechanically fixed on this board of Green/Blue colour or required color. Then these two separate boards fixed back to back on single frame are fixed to two vertical posts of 50mm square pipe 2.0 mtr long to be painted in black and white alternative bands of 25cm height with synthetic enamel paint complete in all respect. (iii) This board on single frame shall be embedded in PCC 1:4:8, type D2 of required size including necessary excavation in post hole all as specified and as directed.

INTERNAL ELECTRIFICATION

Material & Labour for sub main wiring with 2 runs of 2.5 Sqmm as main cable and one run of 2.5 sqmm as earth continuity conductor on wall and surface wiring on ceiling / roof with necessary fixing arrangements using approved colour coding as per IS with single core PVC insulated unsheathed FRLS cable of specified size multistranded copper conductor 1100 volts grade, IS-694 marked, drawn through ISI Marked (IS 9537 Part II) ERW stove enamelled rigid steel conduit suitable for wiring, not less than 20mm dia with all MS conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc., and making good the disturbed surface complete all as specified and as directed.

Notes : (i) Flame proof accessories shall be measured and paid separately. (ii) One switch shall control 4 Nos FP LED light fitting. (iii) 3 runs of 2.5 sqmm cable and 1 run of conduit shall be measured as 1 unit .

Supply & Fixing flame proof weather proof threaded type junction box LM 6 aluminum alloy 3 to 4 way with closing plug complete all as specified and as directed.

Supply & Fixing flame proof weather proof LM6 union for 20 mm dia conduit complete all as specified and as directed.

Supply & Fixing flame proof weather proof LM6 socket for 20 mm dia conduit complete all as specified and as directed.

Supply & Fixing Flame proof switch /isolator cast iron body 16A single pole ON/OFF, 240 volts LM-6 (rotary type) certified by CMRI complete all as specified and as directed.

Supply & Fixing CMRI certified LED Flameproof well glass luminaires 60W with LM 6 aluminum alloy lamp housing, heat resistant and toughened glass, cover hinges cover with neoprene gasket, painted MS bar guard, epoxy finish provided with built in control gear box complete with all accessories internally prewired & eye bolt for suspension, IP65 Protection and including fixing light fitting on wall/ roof and making all electrical connection complete all as specified and as directed.

Supply & Fixing weather proof flame proof with IP55 sheet metal enclosure for DB SPN 8 way 240V - 200A rated bus bar certified by CMRI Dhanbad of cast aluminium alloy LM-6 construction with cable entries at bottom consisting of DB with one 16A, 10KA MCB SPN as incomer and MCB SP 6 A, 10KA -06Nos as outgoing including flameproof cable gland & lugs at bottom side etc. including making connection complete all as specified and as directed.

Material & Labour for earthing with galvanized iron earth plate of size 600 mmx600mmx6mm thick buried directly in ground not less than 2.25 mtr below normal ground level, earth plate packed on all side with charcoal mixed with salt to a thickness of 150 mm connected by GI wire 4 mm dia at two points soldered and riveted to earth plate, GI earth wire protected by using 15 mm bore light grade GI pipe, watering pipe GI 20 mm dia medium grade 2.5 mtr long with funnel, wire mesh etc. necessary earth/brick work and PCC work, disposal of surplus soil to a distance not less than 50 metre, chamber of PCC (1:4:8) type D2 using 40 mm graded stone aggregate, coping in PCC (1:3:6) type C1 using 20 mm graded stone aggregate,

RCC pit cover 50 mm thick (1:2:4) type B1 using 20 mm graded stone aggregate, reinforced with 8 mm MS bar at 80 mm C/C both way, flame funnel wire mesh, testing on completion all as specified and as shown in electrical plate No 3 of MES SSR Part-1 2009 complete all specified and as directed. Note:- Quantity of GI earth wire & protection pipe beyond 7.5mtrs length shall be measured and paid separately.

EXTERNAL ELECTRIC SUPPLY

Material & Labour for Cutting/Demolition of PCC/Hard Standing Plinth Protection/WBM Road not exceeding 20 cm in width and not exceeding 30 cm in depth for passing of LT cable and making good of disturbed surface to match with the existing surfaces by using old and new material i.e. bitumen/PCC 1:3:6 type C1 complete all as specified and as directed.

Supply, installing, testing and commissioning of factory fabricated LT panel board, outdoor type, floor mounted, cubical design type, lock and hood on top and centre opening, double door with locking arrangement, made out of 3.15 mm thick CRCA sheet as per IS & IP protection IP 65, CPRI approved, with bus bar compartments and including copper bus bars, four strips colour coded for each phase of rating 200 Amps for phase and neutral, mounted on hygroscopic / epoxy coated insulators and necessary copper stranded conductor control wiring, cable gland etc. compartmental MCB, mounted on angle iron frame anti rust painted 50 mm x 50 mm x 6 mm of height 0.60 m above ground level and 0.6 m below ground level totally enclosed & completely weather, dust and vermin proof,

cable in/out holes, suitable for three phase 4 wire, 415 volts, 50 Hz, AC supply, cable glands duly powder coated panel, PCC foundation 1:2:4 type B1 using 20 mm graded stone aggregate including necessary earthwork & excavation etc. and comprising of the following items with all clearance as per IE rule complete all as specified and as directed :-

ROAD/PATH/CULVERT

Material and labour for forming embankments including raising(or lowering) earth (moorum/ red bajri obtained from outside MD land), spreading in layers n exc 30 cm thick, watering, ramming/rolling with 8 to 10 Tonne power roller and finishing to required size, shape and height not exceeding 1.50 mtr complete all as specified and as directed.

Material and labour for Granular sub base (GSB) 200mm thick Compacted and conforming to the grading given in Table 400-1 and physical requirement given in Table 400-2, Grading Zone III and IV in Table 400-1 as per MORT&H specification and laid in two layers (each layer of 100mm compacted thickness) by using shingle or gravel spread, rolled and consolidated to a gradient and camber complete all as specified and as directed.

Material and labour for 150mm WMM in two layers (each layer of 75mm) conforming to the grading given in Table 400-13 and physical requirement as per Table 400-12, spread with mechanical means and rolled using 8-10 Tonne vibratory power roller over compacted sub grade surface as specified in clause 406.3.5 on page 134-135 MORT&H specification complete all as specified and as directed.

Material & Labour for providing PCC 1:3:6 type C1 (20mm graded stone aggregate) as kerb stone of size 35cm x 30cm x 15cm, long set in cement mortar 1:6 in line complete including necessary earth work in any type of soil to fix in position all as specified and as directed.

Material & Labour for preparing surface of unsurfaced WMM surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc. and applying evenly a priming / tack coat with cold emulsion primer with cationic bitumen SS grade-I confirming to IS: 8887 (using paving bitumen) at the rate of 10 Kg per 10 Square metre of road surface complete all as specified and as directed.

FIRE BREAK

Material and labour for 150mm thick PCC M-25 design mix using 20mm graded stone aggregate as in flooring using tremix vacuum dewatering method including all necessary equipments for finishing the floor using tremix method complete all as specified and as directed.

LIGHTENING PROTECTION

Material & Labour for earthing complete with GI mild steel earth plate electrode 600mm X 600mm X 6 mm thick, burried directly in ground veritcally (Earth pit not less than 2.25 metre deep below ground level) with top edge of the earth plate not less than 1.5 metres below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and earth plate connected to GI strip of size 32 x 6 mm by means of bolts, nuts, check nuts and washers of steel and riveted to earth plate at one end and connected to metallic bodies of equipment etc. at other end, earth strip encased in and

including 40mm bore GI light grade pipe with all fitting from top of electrode to the body of equipment fixed with and including 25 x 4mm flat iron clamps, bolts, nuts and washer and also including GI pipe 20mm dia medium grade for watering from bottom of earth pit to top of electrode including GI funnel with wire mesh all as shown in electrical plate No. 3 including PCC pit (1:3:6) type C1 in cement concrete 40mm thick precast RCC cover in (1:2:4) type B1 reinforced with 8mm dia TMT bars @ 75 c/c both ways with 01 No lifting handle of 12mm dia MS plain bar, etc. complete all as specified and as directed. NOTE : Quantity of GI strip/ protection pipe beyond 7.5mtrs length shall be measured and paid separately.

Material & Labour for PCC block of size 300mm x 300mm x 300mm in 1:3:6 type C1 (using 20 mm graded stone aggregate) with duly grouted MS bolt of suitable size to fix aluminium strip with nuts & washers for aluminium air termination rod stand post on roof including necessary formwork complete all as specified and as directed.

Supply & fixing single pointed air termination aluminium rod, 12 mm dia 600mm long complete all as specified and as directed.

STATIC DISCHARGE

Material & Labour for earthing complete with copper earth plate electrode 600mm X 600mm X 3 mm thick, burried directly in ground (Earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to copper strip 20x3 mm as earth lead by means of bolts, nuts, check nuts and washers of copper or brass connected to earth test point including watering pipe 20mm bore GI pipe medium grade from bottom of earth pit to top of electrode and 32 mm bore light grade GI Pipe protection pipe up to 7.5 Mtr from earth strip complete with wire mesh, funnel, necessary excavation and earth work in any type of soil/ strata, PCC chamber in 1:3:6 type C1, 550mmx550mmx50mm including CI cover 10 mm thick hinged to CI frame, complete all as shown in electrical plate No 3 and all as specified and or indicated including testing on completion complete all as specified and as directed.

NOTES :- (a) Quantity of copper strip/ protection pipe beyond 7.5mtrs length shall be measured and paid separately. (b) On testing, after completion, if the earth resistance < 5 ohms is not obtained, earthing shall be rejuvenated at no extra cost till the desired earth resistance is obtained.

Supply & Fixing Post insulator epoxy LV type suitable for holding aluminium air termination rod 12 mm dia fixed on stand post including screws complete all as specified and as directed.

EARTHWORK FOR COMPACTED EARTH TRAVERSE

Material and labour for bringing outside MD land soil by rough excavation, forming embankment including raising (or lowering) earth, spreading and levelling in layers n.exc 30 cm thick, watering, ramming / rolling with 8 tonne roller and finishing to required size, shape upto the height shown in drawing from base all as specified and directed. Note:- The item is inclusive of rate loading / unloading of soil from lead of any distance. contractor shall visit the site before quoting the tender.

Material and labour for forming embankment using excavated soil including raising (or lowering) earth, spreading and levelling in layers n.exc 30 cm thick, watering, ramming / rolling with 8 tonne roller and finishing to required size, shape upto the height shown in drawing from base all as specified and directed. Note:- The item is inclusive of rate loading / unloading of soil from lead of any distance. contractor shall visit the site before quoting the tender.

Total amount of Schedule 'A' Part X carried over to General Summary

Blank

Blank

Blank

Blank

GENERAL SUMMARY

Lumpsum price worked out by the contractor for “BUILDING & STRUCTURE” as listed in Schedule ‘A' Part I representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part I on Srl Page No. 36

Lumpsum price worked out by the contractor for “SITE CLEARANCE, EXCAVATION AND EARTH WORK” as listed in Schedule ‘A' Part II representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part II on Srl Page No. 38

Lumpsum price worked out by the contractor for “EXCAVATION AND EARTH WORK (FOR IGLOO BUILDING PORTION)” as listed in Schedule ‘A' Part II(A) representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part II(A) on Srl Page No. 40

Lumpsum price worked out by the contractor for “DEMOLITION OF BUILDINGS” as listed in Schedule ‘A' Part III representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part III on Srl Page No. 42

Lumpsum price worked out by the contractor for “EXTERNAL ELECTRIFICATION” as listed in Schedule ‘A' Part IV above/below the lumpsum price as inserted by MES for Schedule ‘A’ Part IV on Srl Page No. 44

Lumpsum price worked out by the contractor for “ROAD/ PATH/ CULVERT” as listed in Schedule ‘A' Part V representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part V on Srl Page No. 46

Lumpsum price worked out by the contractor for “FIRE BREAK" as listed in Schedule ‘A' Part VI representing above/below the lumpsum price inserted by MES for Schedule ‘A’ Part VI on Srl Page No. 48

Lumpsum price worked out by the contractor for “AREA DRAINAGE” as listed in Schedule ‘A' Part VII representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part VII on Srl Page No. 50

Lumpsum price worked out by the contractor for “LIGHTENING PROTECTION” as listed in Schedule ‘A' Part VIII representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part VIII on Srl Page No. 52

Lumpsum price worked out by the contractor for “STATIC DISCHARGE” as listed in Schedule ‘A' Part IX representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part IX on Srl Page No. 54

Total amount of SCHEDULE 'A' PART X (MISC B/R & E/M ITEMS) brought forwarded from Serial Page No. 73(R)

VISHAL INFRASTRUCTURE LTD

SIBAL AND SIBAL

M/s godara infratech and power industries