GE/PNH-38/2020-21

Amount

Schedule 'A' Part-I (Building Work) JOB NO. SHQ/POONCH /REV-07/2019-20 (Toilet with bathroom block) & SHQ/POONCH/REV-08/2020-21 (Toilet with bathroom block)

Total amount of Sch 'A' Part-I (Building work) brought forward from srl page No-19.

Schedule 'A' Part-II (Internal Water Supply works) JOB NO. SHQ/POONCH /REV-07/2019-20 (Toilet with bathroom block) & SHQ/POONCH/REV-08/2020-21 (Toilet with bathroom block)

Total amount of Sch 'A' Part-II(Internal Water Supply works) brought forward from srl page No-20

Schedule 'A' Part-III (Plumbing works) JOB NO. SHQ/POONCH /REV-07/2019-20 (Toilet with bathroom block) & SHQ/POONCH/REV-08/2020-21 (Toilet with bathroom block)

Total amount of Sch 'A' Part-III(Plumbing works) brought forward from srl page No-21

Schedule 'A' Part-IV(Sec-I) (Internal Electrification works) JOB NO. SHQ/POONCH /REV-07/2019-20 (Toilet with bathroom block) & SHQ/POONCH/REV-08/2020-21 (Toilet with bathroom block)

Total amount of Sch 'A' Part-IV(Sec-I)(Internal Electrification works) brought forward from srl page No-23

Schedule 'A' Part-IV(Part-II) (Internal Electrification works) JOB NO. SHQ/POONCH /REV-07/2019-20 (Toilet with bathroom block) & SHQ/POONCH/REV-08/2020-21 (Toilet with bathroom block)

MCB single pole and neutral 40 amps 240 volts 10 KA 'C' series all as specified. Make:- Havells cat part No-DHMGCSNF040 or Equivalent cat part of make of make:- Legrand /Indoasian.

LED lamp CDL 10 watt with holder base (B22) type & 3 star rating, complete all as specified. Make of LED lamp:- Havells cat part No LHLDEUEBML8Z010 or Equivalent cat part of make:-Wipro / Crompton / Bajaj / cropmpton

Tube light fitting with universal batten suitable for T8 LED lamps LED 20W tube Rod with end cap complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting including 20LED tube rod 4 feet long (Double Side Connection) fixed, complete all as specified and directed. Make:-Havells Cat Part No:-REGALBATTENT8UPTO1X22WSSBSWH for fittings & CRYSTAL 1213T8DSTL20WLED865SGLASS for LED tube rod or Equivalent cat part of make as specified in Appx 'A' here in after. Note :- The LED batten and LED tube rod shall be of same make.

Schedule 'A'Part-V(Sec-I) (Sewage Disposal Works) JOB NO. SHQ/POONCH /REV-07/2019-20 (Toilet with bathroom block) & SHQ/POONCH/REV-08/2020-21 (Toilet with bathroom block)

Total amount of Sch 'A' Part-V(Sec-I)(Sewage Disposal WorKs) brought forward from srl page No-25

Schedule 'A'Part-V(Sec-II) (Sewage Disposal Works) JOB NO. SHQ/POONCH /REV-07/2019-20 (Toilet with bathroom block)

Construction of septic tank with cover slab of RCC 1:1.5:3 for 5 user brick work in CM 1:4 (with top of slab at ground level) including necessary filing and disposal of surplus soil as directed, RCC manhole cover with iron welded frame complete, vent shaft cowl, all as shown on drawing No CE/TD-1202/2003 sheet 1/2 and 2/2 amended upto date and as directed.

Schedule 'A'Part-VI(Protective Works) JOB NO. SHQ/POONCH/REV-08/2020-21 (Toilet with bathroom block)

Total amount of Sch 'A' Part-VI(Protective Works) brought forward from srl page No-26

Schedule 'A'Part-VII(External water supply Works) JOB NO. SHQ/POONCH /REV-07/2019-20 (Toilet with bathroom block) & SHQ/POONCH/REV-08/2020-21 (Toilet with bathroom block)

Total amount of Sch 'A' Part-VII(External water supply Works) brought forward from srl page No-27

Schedule 'A'Part-VIII(External electric supply Works) JOB NO. SHQ/POONCH/REV-08/2020-21 (Toilet with bathroom block)

Total amount of Sch 'A' Part-VIII(External electric supply Works) brought forward from srl page No-28

Schedule 'A'Part-IX(Demolition Works) JOB NO. SHQ/POONCH/MINOR-07/2020-21 (Demolition work against BLDG No T-24, T-26, T-28, T-03 & T-55 at 425 FD HOSPITAL)

Total amount of Sch 'A' Part-IX(Demolition Works) brought forward from srl page No 29-30

Schedule 'A'Part-X (Misc Items of Works) Note : This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 siginifies this fact only.(JOB NO. SHQ/POONCH/LBW-02/2020-21 (Provn of 01 x 62.5 KVA Generator set with connected works))

Prime Mover : Prime mover suitable for driving alternator 62.5 KVA Capacity having the suitable BHP at 1500 RPM for rated output for alternator in accordance with latest BS/IS Specification with electric starting device with all standard fittings and suitable capacity of lead acid maintenance free battery of 12 Volts 180AH -01 nos with Battery and Charger Engine over speed safety mechanism shall be incorporated. The engine shall be equipped with standard fittings as per manufacture's recommendations.

Engine Control Panel : (a) All relevant parameters shall be conventionally displayed on complete panel thereby providing easy monitoring of lub oil, pressure, Coolant Temperature, Battery charging, Ammeter, RPM, Hour meter and starting switch etc. (b) AMF Panel with Bye Pass arrangement for Main and DG Both supply, internal wiring and power contactors suitable for 62.5 KVA generator set, all as per manufacturer's recommendation. Bye Pass arrangement Main & DG set Supply along with all the parameters and accessories as per manufacturer recommendation and CPRI Approved & as per relevant IS.

Fuel Tank : Fuel Tank of 12 hours capacity will be installed as per the manufacturer's requirement including all necessary pipe connections from fuel tank to engine and over flow from engine to tank.

Engine Alternator: Engine alternator 62.5 KVA output 3 Phase 50 HZ 415 Volts 4 wire AC supply 0.8 Power Factor at 1500 RPM self regulated self excised screen protected and drip type, insulation class 'H' continously rated brush less type conforming to relevant BS/ IS code as per current manufacturing shedule of standard manufacturer. Engine Alternator shall be mounted on specially designed base plate of rigid welded constructions with anti vibraton pads. The DG Set shall be placed on foundation including necessary civil works as per the manufacturer's recommendations/site requirement. The output of alternator not less than 62.5 KVA in all adverse conditiones, as the DG set to be installed at HAA 950 m above MSL. Note:- (a) The unit rate shall deemed to include the cost of Diesel and lubrication required for testing and commissioning of DG Set as per department procedure and shall be arranged by contractor. (b) Extenssion of exhaust pipe for DG set along with standerd accessories like flange, nut bolts , asbestous rope etc shall be provided by the contractor and the cost of the same shall be included in the unit rate quoted by contractor. (c) Cost of foundation and necessary civil works as per the manufacturer's recommendations/site requirement shall be incuded in the unit rate quoted by the contractor.

Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron earth lead strip 32x6mm by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 40mm bore including GI medium grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 8mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion, complete all as specified and directed.

Supply, laying, testing cable XPLE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable, heavy duty 1100 volts grade, with stranded aluminium conductor of size 150 Sqmm 3.5 core complete all as specified and as directed.

Supply, laying, and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 Sqmm 3.5 core all as specified and directed.

Excavation in trenches not exc. 1.5 m wide and not exc. 1.5 in depth for laying of cable or any work as directed, getting out in any type of soil, complete all as specified and directed.

Returning filling in including spreading levelling watering and well ramming in layers not exc. 25 cm thick each complete all as specified and directed.

Removing excavated material to a distance not exc. 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point of any type of soil, complete all as specified and directed.

Sand cushioning to under ground cable providing with a layer of and 08 cm thick before laying of cable and 15 cm after laying of cable in trenches, hand punning complete all as specified and directed by Engr-in-charge (Note : punning thickness of 18 cm will be measured for payment)

Sub class 'B' bricks laid dry flat transversely along the length of cable with width equal to the length of brick over sand cushioning as protection cover of cable laid in trenches, complete all as specified.

Construction of platform suitable for 62.5 KVA Generator set / Voltage stabilizer of size 4.0m x 2.0m x0.6 m (Platform shall be made out of brick masonary in CM 1:4 one feet below ground level and one feet above ground level hollow space consructed with one brick thick wall, 100mm thick PCC 1:5:10 type E-2 in foundation and to be filled by PCC 1:3:6 type C-2 in hollow space and provided with 100mm thick cement concrete 1:2:4 type B-2 as in floor of platform, 10mm thick plastering in CM 1:4, complete all as specified and directed.

Krishana Enterprises

Jiwan Singh

M/S BONA CONSTRUCTION