ADDN/ALTN TO CERTAIN BUILDINGS OF 1 ARMY HQ SIGNAL REGIMENT SIGNALS ENCLAVE RTR MARG UNDER GE(CENTRAL) DELHI CANTT

Amount

BUILDING WORK (B/R)

Item No 1 Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and get ting out in any type of soil including removal from site and depsited outside MOD land all as specified and directed.

Item No 2 Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting in out any type of soil complete all as specified and directed.

Item No 3 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Item No 4 Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

Item No 5 M&L PCC 1 : 4 : 8 type D2 using 40mm graded stone aggregates as in foundation of manholes, posts etc complete all as specified and directed.

Item No 6 S&F Mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. Note : TMT bars may also be used for strengthening existing reinforcement.

Item No 7 All as per Item No 6 above but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders

Item No 8 M&L for reinforced cement concrete (Design mix) of M-25( Using 20mm graded crushed stone aggregate aggregate) for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Item No 9 All as per item No. 8 above but in Columns, pillars, piers, posts and struts

Item No 10 All as per Item No.8 above but in Beams, cantilevers, bressummers, lintels over 1.5m span

Item No 11 All as per item No.8 above but Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

Item No 12 All as per item No. 8 above but in chajjas

Item No 13 All as per item No. 8 above but Chullah hoods; stairways (except spiral staircases) including steps (square or spandril), string pieces, carriages, etc., complete, any section straight or winding, but excluding landings

Item No 14 All as per item No. 8 above but Domes, vaults, shell roofs, arch ribs and folded plates

Item No 15 All as per item No. 8 above but Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses

Item No 16 All as per item No. 8 above but Fins, fascias, louvres, parapets, and railings exc. 60cm in height, ls, balustrade, and the like

Item No 17 M&L for Providing precast cement concrete 1:2:4 Type B1 (using 20mm graded crushed stone aggregate) in window or door cills, lintels,bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar complete with joints to match complete all as specified and directed.

Item No 18 M&L for on flat surface Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter finished fair complete all as specified and directed.

Item No 19 M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions with fair finished rough flat surfaces complete all as specified and directed.

Item No 20 M&L for formwork to soffits of suspended slabs such as roof slabs,floor slabs, landings and similar work; n.exc 200mm thick fair finished concrete flat surface complete all as specified and directed.

Item No 21 M&L Cement concrete 1:2:4 type B1(using 20mm graded crushed stone aggregate) as in bed blocks for hold fast, coping, benching etc. including weathering, slightly rounded or chamfered angles or throating including form work to concrete surfaces complete all as specified and directed.

Item No 22 Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for including cutting reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet and removal of debris and rubbish out side MoD land complete all as specified and directed.

Item No 23 Demolition of cement concrete of any description and in any situation as in sunken floor complete all as specified and directed.

Item No 24 Demolition of brick work built in cement mortar in any description and position complete all as specified and directed.

Item No 25 Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15 cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land) complete all as specified and directed.

Item No 26 Dismantling of PVC water tanks of exc 250 litres and n.exc 500 litres capacity of any condition or type complete all as specified and directed.

Item No 27 Dismantling of Cast Iron pipe/ RCC drain pipe/PVC pipe up to 150 mm bore complete all as specified and directed.

Item No 28 S&F 150 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with lead joint fixed to walls, complete all as specified.

Item No 29 All as per Item No. 28 above but except pipes

Item No 30 S&F 100 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with lead joint fixed to walls, complete all as specified.

Item No 31 All as per Item No. 30 above but except pipes

Item No 32 S&F 75 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with lead joint fixed to walls, complete all as specified.

Item No 33 All as per Item No. 32 above but except pipes

Item No 34 S&F 150mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

Item No 35 S&F 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

Item No 36 S&F 75mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

Item No 37 M&L for 150mm bore UPVC (SWR) bends any radius all as specified and directed.

Item No 38 M&L for 110mm bore UPVC (SWR) bends any radius all as specified and directed.

Item No 39 M&L for 75mm bore UPVC (SWR) bends any radius all as specified and directed.

Item No 40 S&F 150mm dia (bore of pipe) cast iron Tee diminishing pieces or tapers (larger bore measured) with lead joints, complete all as specified.

Item No 41 S&F 100mm dia (bore of pipe) cast iron Tee diminishing pieces or tapers (larger bore measured) with lead joints, complete all as specified.

Item No 42 All as per item 38 above but 75mm dia (bore of pipe) Tee

Item No 43 S&F 150mm dia (bore of pipe) branch pieces cast iron single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fixed with lead joints fitted with oval access door, complete all as specified.

Item No 44 S&F 100mm dia (bore of pipe) branch pieces cast iron single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fixed with lead joints fitted with oval access door, complete all as specified.

Item No 45 S&F 75mm dia (bore of pipe) branch pieces cast iron single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fixed with lead joints fitted with oval access door, complete all as specified.

Item No 46 S&F 150mm dia (bore of pipe)Swan necks cast iron (or off-sets) upto 152 mm projection fixed with lead joints complete all as specified.

Item No 47 S&F 100mm dia (bore of pipe)Swan necks cast iron (or off-sets) upto 152 mm projection fixed with lead joints complete all as specified.

Item No 48 S&F 75mm dia (bore of pipe)Swan necks cast iron (or off-sets) upto 152 mm projection fixed with lead joints complete all as specified and directed. .

Item No 49 S&F 150mm dia (bore of pipe)Cast iron cowl fixed with lead joints complete all as specified and directed.

Item No 50 S&F 100mm dia (bore of pipe)Cast iron cowl fixed with lead joints complete all as specified and directed.

Item No 51 S&F 75mm dia (bore of pipe) Cast iron cowl fixed with lead joints complete all as specified and directed.

Item No 52 M&L for 150mm dia UPVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed.

Item No 53 M&L for 110mm dia UPVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed.

Item No 54 M&L for 75mm dia UPVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed.

Item No 55 S&F in repair cast iron floor trap square type with Cockroch Proofing CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, complete all as specified and directed.

Item No 56 S&F in repair cast iron floor trap square type with Cockroch Proofing CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 100 mm, complete all as specified and directed.

Item No 57 S&F in repair Cast iron Nahani trap with CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, complete all as specified and directed.

Item No 58 S&F in repair Cast iron Nahani trap with CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 100 mm, complete all as specified and directed.

Item No 59 M&L for 100mm cast iron sanitary connection socket to fit WC out-let complete all as specified and directed.

Item No 60 M&L for 100mm cast-iron sanitary connection bend (92½0), with arms 380 to 450mm, excluding joint complete all as specified and directed.

Item No 61 M&L for 100mm cast iron sanitary connection ‘S’ branch, with branch 370 to 450mm long excluding joint complete all as specified and directed.

Item No 62 S&F in repair 150 mm pipe, stack clamps out of 50mmx 5 mm flat iron and 16 mm dia round iron stamp including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

Item No 63 S&F in repair 100 mm pipe, stack clamps out of 50mmx 5 mm flat iron and 16 mm dia round iron stamp including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

Item No 64 S&F in repair 75 mm pipe, stack clamps out of 50mmx 5 mm flat iron and 16 mm dia round iron stamp including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

Item No 65 S&F white colour Rotational moulded polyethylene water storage tank 500 litres capacity, triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings complete all as specified and as directed.

Item No 66 All as per Item No. 65 above but 750 Litres

Item No 67 All as per Item No. 65 above but 1000 Litres

Item No 68 Disconnecting existing tanks, of capacity Exc 500 & n exc 1000 litres setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) complete all as specified and directed.

Item No 69 Disconnecting existing tanks, of capacity Exc 250 & n exc 500 setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed. Note:- Cleaning repairing, etc. measured separately

Item No 70 Taking up or down 15 mm bore GI tubing and connections including cleaning for re-fixing complete all as specified and directed.

Item No 71 All as per Item No. 70 above but 20 mm bore

Item No 72 All as per Item No. 70 above but 25 mm bore

Item No 73 M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturbed surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate complete all as specified and directed.

Item No 74 S&F 15mm bore GI tubing medium grade with all fittings and fixed to walls and ceiling or laid in floors etc complete all as specified and directed.

Item No 75 All as per Item No. 74 above but 20 mm bore

Item No 76 All as per Item No. 74 above but 25 mm bore

Item No 77 Refixing old 15mm bore galvanised steel tubing and connections with and including new (ISI Marked) fittings/fixtures fixed to walls or laid under floors etc complete in new or old position on walls, ceiling, floors etc complete all as specified and directed.

Item No 78 All as per Item No. 77 above but 20 mm bore

Item No 79 All as per Item No. 77 above but 25 mm bore

Item No 80 S&F 20mm dia Ball brass valves, high pressure, with polythene float and fly- nut com-plete, scre-wed for iron pipe or brass ferrule , plastic ball screwed for iron pipe and fixed complete all as specified and directed.

Item No 81 S&F Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron iron complete all as specified and directed.

Item No 82 Fixing only Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron iron complete all as specified and directed.

Item No 83 Taking down cement plaster in brick walls, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified.

Item No 84 M&L for Brick work with sub class B bricks of old size, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Item No 85 M&L for Brick work with sub class 'B' bricks using old size bricks, straight or curved on plan to any radious in half brick thick wall built in CM 1:4 complete all as specified and directed.

Item No 86 M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 mixed with water proofing admixture finished even and smooth without using extra cement complete all as specified. (Note:- Water proofing admixture shall be measure and paid separatelly).

Item No 87 M&L for 15 mm thick internal rendering in CM 1:6 on fair face of brick walls/ concrete surface and finished even and smooth without using extra cement, complete all as specified and directed.

Item No 88 M&L for 10 mm thick rendering in CM 1:3 on concrete surfaces of ceiling, chajja and like surface finished even and smooth without using extra cement complete all as specified and directed.

Item No 89 Dismantling floor hearth or wall tiling including cement mortor bedding (but not backing) laid bedded and pointed in any mortar and removal of old tiles from premises complete all as specified and directed.

Item No 90 M&L for 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in sub floors finished rough complete all as specified and directed.

Item No 91 M&L non-skid Coloured ceramic rectified tile 300x300x7-8 mm thick as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Item No 92 M&L for Glazed ceramic coloured tiles 350 x250x 7 mm/ 450x 350x7 mm thick in dado, set and jointed in neat cement slurry and pointed in colour cement to match the surface over and including 10 mm thick rendering in CM 1:4 complete all as specified and as directed.

Item No 93 M&L for Glazed ceramic coloured tiles 200x300x 6 mm thick in dado, set and jointed in neat cement slurry and pointed in colour cement to match the surface over and including 10 mm thick rendering in CM 1:4 complete all as specified and as directed .

Item No 94 M&L Coloured ceramic rectified tiles 600mm x 600mm x10 mm thick , joint free as in floors over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Item No 95 M&L Coloured glazed ceramic rectified tiles 600 mm x 600 mm x 10 mm thick as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Item No 96 M&L for kota stone slab (Uniform texture) of 20 to 22 mm thick in floor (minimum size 580x 580mmx 20 mm thick) with boarder of 20 mm thick white marble slabs 75mm to 100mm wide (as directed by GE) laid over and including 15mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polished complete all as specified and directed.

Item No 97 M&L for kota stone slab (Uniform texture) of 20 to 22 mm thick (minimum thickness 20 mm ) in Tread/Riser of steps, skirting, dado and pillars in one single piece (size decided by Engr-in-Charge) laid over and including 15mm thick screed bed in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polished complete all as specified an directed. Note :- The steps shall be provided with grooves of both side (03 Nos on each end), The face of the steps shall be bullnosed. The rate quoted by the contractor deemed to be included for above aspect and for entire completion of work.

Item No 98 M&L Granite of 18 to 20mm thick with uniform texture (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM 1:4 including pointing with white cement (1:2) using marble dust with admixture of pigment to match with marble shade of makrana doogri green colour stone for Kitchen cooking platform laid over and including 15mm thick screed bed in CM 1:6 polishing bevelled edges of corner etc complete all as specified and directed.

Item No 99 All as per Item No. 98 above but on vetical surfaces including 15 mm thick rendering in CM 1:4

Item No 100 S&F Steel pressed frame for doors with one or more rebates including necessary fixing logs, 6 Nos of SS hinges, lock strike plate etc complete all as specified and directed. Size of frame 125mm x 60mm complete all as spcified and directed.

Item No 101 Dismantling of Brick tiles or terracing tiles, single layer on roofs, kerbs, aprons, etc. (each layer) complete all as specified and directed.

Item No 102 Dismantling Mud phuska in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) and disposal out of MoD Land complete all as specified and directed.

Item No 103 M&L Cement concrete 1:2:4 type B0 (using 12.5mm graded crushed stone aggregates) as in roof levelling complete all as specified and directed.

Item No 104 M&L Applying a coat of bituminius primer confirming to IS 3384 @ 0.5 ltr/sqm on prepared surface of plaster after drying of primer, applying a coat of hot blown bitumin 85/25 grade @ 1.2 kg/sqm and applying APP based Polymeric membrane minimum weighting 3 kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gram/sqm) and sealing joints by torch application over the APP memberane by applying semi hot blown bitumin 85/25 @ 0.5 Kg/Sqm and dusting over the bitumin coat complete all as specified and directed.

Item No 105 M & L for supreme quality Heat Resistant Terrace Tiles of size 250x250x 20mm thick ,tiles are specially developed to integrate seamlessly with the concrete roof to provide an efficient solution for hot climatic conditions for residential accommodation. The eco efficient tiles are made from premium grade materials under strict quality supervision. Further, these easy to install tiles are suitable for retrofitting projects over 15mm thick screed in CM 1:4 mixed with water proofing compound as per manufacturer instruction complete all as specified and directed. Note : - Make of tile will be best quality as approved by GE

Item No 106 Taking down chowkats or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Item No 107 Taking down chowkats or frames exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Item No 108 Taking down shutters of any description exc 1 sqm and not exc 2 sqm each complete all as specified and directed.

Item No 109 Taking down shutters of any description exc 1 sqm and not exc 2 sqm each and refixing in the same or other opening by easing as required at site complete all as specified and directed. Note : The rate quoted by the contractor are inclusive of taking down old mild steel hinges carefully without damaging and refixing in the same or other opening as directed. Nothing extra cost will be allowed in this account .

Item No 110 S&F Fiber Glass Reinforced Plastic (FRP) Door Frames of cross section 90mm x 45mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

Item No 111 S&F 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardantgrade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames complete all as specified and directed.

Item No 112 M&L Frame work as in door chowkhats with angle iron welded together ends of angle shouldered and fixed to opening and welding 3 Nos mild steel butt hingese, and 6 nos hold fasts made out of FI 25x3 mm 30 cm long for fixing of chowkhats( Butt hinges paid separately) conforming to Fe 290 Gde E-165 complete all as specified and directed

Item No 113 S&F 1st class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed all as specified and directred.

Item No 114 S&F 40mm thick factory made Flush shutters, solid core construction, with block board core and both face is covered with decorative face veneer with lipping/frame to match all as specified and directed.

Item No 115 S&F 35mm thick factory made flush shutters solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed.

Item No 116 M&L Factory made 2nd class hard wood glazed and skeleton shutter 35mm thick, factory made, open rebated and prepared to receive glass/guage etc, without sash bars, mitred and rebated, with edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/guage etc, sizes of members of shutter as specified in section 8, clause 8.24(a) of SSR Part I complete all as specified and directed.

Item No 117 S&F 25 mm thick factory made flush shutter solid core construction with block board core and ply wood face panel commerical type on both side to be fixed as shutter of cupboard/kitchen cup board/loft board complete all as specified and directed.

Item No 120 M&L Factory made 2nd class hard wood glazed and skeleton shutter 30mm thick, factory made, open rebated and prepared to receive glass/guage etc, but divided into squares, with plain, cham-fered or roun-ded, mitred and rebated sash bars, any numberswitht sash bars, mitred and rebated, with edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/guage etc, sizes of members of shutter as specified in section 8, clause 8.24(b) of SSR Part I complete all as specified and directed.

Item No 121 S&F powder coated (minimum thickness of powder coating 50 micron) aluminum frames for windows/ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified.

Item No 122 S&F anodised aluminum powder coated (minimum thickness of powder coating 50 micron) glazed/gauzed windows and ventilators shutters side hung type with sash bar aluminum section weighing 0.65 kg per mtr including necessary jointing cleats glazing clips rubber packing anodised aluminum beading screws including fittings such as 1no of hook & eye 150mm long,2 no Alluminium hinges 75mm long,2 no100 mm long tower bolt and one no alluminium handle 100mm long, 4mm thick glass panes and stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm etc.and mild steel grills of 12mm dia square bars 10cm c/c with frame of 50x6mm mild steel flat “ Note :- The rate quoted by the contractor is deemed to be included for all fittings/fixtures required for entire completion of work.

Item No 123 S&F 100 mm long (size) butt hinges, medium weight, cold rolled mild steel, complete all as specified.

tem No 124 All as per Item No. 123 above but 75 mm long

Item No 125 S&F 300mm long, Aluminium anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete all as specified and directed.

Item No 126 S&F aluminium anodised barrel tower bolt 200 mm long, extruded section complete all as specified and directed.

Item No 127 All as per Item No. 126 above but 150 mm long

Item No 128 S&F extruded aluminium alloy handle of size 150mm size complete all as specified and directed.

Item No 129 S&F Aluminium anodised floor door stopper with hard drawn steel spring 140mm long complete all as specified and directed.

Item No 130 S&F Hasp and staple, 75mm size, safety type, brass with mild steel hinge pin including bolt to hinge plate & fixed with screws, complete all as specified and directed.

Item No 131 S&F 150mm size double action spring, hinge, mild steel with steel wire spring, stove enamelled black, complete all as specified and directed.

Item No 132 M&L framed work such as grills, grating etc with ends of bars shouldered or riveted or forged into spikes framed guard bars, railing with MS tubes and similar work confirming to Fe - 290-0 or E-165 complete all as specified and directed.

Item No 133 Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

Item No 134 S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with steel wire staples, complete all as specified and directed.

Item No 136 S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with steel wire staples inclding necessary fixing beads etc complete all as specified and directed.

Item No 137 S&F 5.00 mm thick plain sheet glass and glazing with oil putty in square n.exc 0.5 Sqm in each pane, complete all as specified and directed.

Item No 138 S&F 4.00 mm thick plain sheet glass and glazing with oil putty in square n.exc 0.5 Sqm in each pane, complete all as specified and directed.

Item No 139 S&F factory made PVC frame of size 75x40mm with wall thickness of 4mm made out of extruded 4mm thick plain or prelam PVC sheet reinforced with 15x15mm MS square tube of 19 gauge thickness through out the frame and mitred cut and two corners and jointed with two nos of 150mm long bracket of 10x10mm MS Square tube. The door frame shall be fixed to the wall using 65x100mm long MS screws though the frame by using PVC fastners minimum of four Nos of screws to be provided for each vertical members and minimum of two nos of screws to be provided horizintal members etc complete all as per manufacture instructions and as directed.

Item No 140 S&F 18/19mm thick PVC moulded solid board one side prelam for cabinet boxes etc with self and shutter full size fitted under/above the kitchen cooking platform and other platform including all necessary fitting/fixture like magnetic catcher, knobs, hinges, L-Bihari etc complete all as specified and directed . Note :- The rate quoted by the contractor is deemed to be included for the entire completion of work. Nothing will be extra paid under this item.

Item No 141 S&F in repair 40mm dia, cup boards stainless steel knobs fixed with nuts , screw and washer of mild steel bright finished complte all as specified and directed.

Item No 142 S&F Continuous piano hinges stainless steel of AISI 304 grade width of flaps (when open) 30mm complete all as specified and directed.

Item No 143 M&L Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Item No 144 All as per Item No.143 above but two coat of synthetic enamel paint on old wooden surfaces

Item No 145 M&L Preparation of new or previously untreated steel surfaces of any description over 10cm in width or girth,not otherwise specifically and applying two coats of synthetic enamel paint over a coat of redoxide primer complete all as specified and directed.

Item No 146 All as per Item No.145 above but two coat of synthetic enamel paint on old steel surfaces

Item No 147 M&L 19mm thick block board of commercial type fixed with screws to timber frame workMDF boards, grade 1 quality, exterior grade, commercial type, fixed with screws to timber frame-work face complete all as specified and directed.

Item No 148 M&L dark shade vitified tiles of 10 mm thick (square/rect) area of each tiles 600x600mm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match 15mm thick screed bed or bedding layer in cm 1:6 etc complete all as specified and directed.

Item No 149 M&L Light shade vitified tiles of 10 mm thick (square/rect) area of each tiles 600x600mm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match over 15mm thick screed bed or bedding layer in cm 1:6 etc complete all as specified and directed.

Item No 150 Material and labour Light shade vitrified tiles 600x100 mm of 10 mm thick in walls etc set and jointed in neat cement slurry and pointing in coloured cement including 10 mm thick rendering in cement mortar (1:4) as in skirting 100 mm high in rooms complete all as specified and directed.

Item No 151 M&L for 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection laid in bays & surfaces finished fair and even complete all as specified and directed.

Item No 152 Supply only liquid water proofing admixture complete all as specified and directed.

Item No 153 S & F in repairs vitrious china urinal, full stall type, coloured complete including CP Waste, urinal spreader Waste pipes, 15mm dia Chromium plated Push cock, providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in white cement, gratings and union for discharge pipes complete all as specified and directed.

Item No 154 S & F in repairs vitreous china coloured European type WC of P or S trap , floor mounted (One piece EWCs with duroplast slim seat cover and twin flush fittings) including connection to drain and fixing bolts, Plastic water closet seat cover complete all as specified and directed. Make CERA Model CONCA, Cat No.S1014166 or equivalent of Hindware or Parryware. NOTE : The rate quoted by the contractor for the above item is inclusive of all fittings and fixture and for entire completion of work.

Item No 155 S&F in repair viterous china squatting pan 'ORISSA Pattern' size 580x440mm white with integral foot rests incl P or S Trap) (excluding flushing cistern & flush pipe) complete all as specificed and directed.

Item No 155A S & F in repairs vitreous china coloured Wash hand basin of size 580 x 440 x 290 mm with full pedestal of height 800mm complete including 32mm dia CP Waste, 02 Nos of CP Connection 450mm long and PVC down pipe of 750mm long , including provision of pair of mild steel iron brackets of suitable size duly painted and cutting for and pinning in ends of brackets in walls and making good complete all as specified and directed. Make CERA, Model CELESTE Cat No.S2040113 (WHB) and Cat No. S2090106 Pedestal or equivalent make of Hindware or Parryware.

Item No 156 S & F Brass CP Health Faucit with 8mm dia 1.20m long brass CP flexible tubes and wall hook screwed for iron pipe complete all as specified.

Item No 157 S&F in repairs PVC valveless syphonic action dual flushing cistern 10ltr capacity, low level, white with inlet, ball valve, float and handle incl brackets and connection to pipes and fixing of chain and pull or lever if any complete all as specified.

Item No 158 S&F Brass CP basin mixer for mixing hot & cold water screwed down for iron pipe 15 mm bore, screwed down high pressure, screwed for iron pipe and fixed complete all as specified and directed.

Item No 159 S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracked guard and railing 60 cm long complete all as specified and directed.

Item No 160 S&F stainless steel sink AISI 316 grade without drainage board of 1 mm thick kitchen or laboratory with plug , washer and waste, 15mm bore brass Chromium plated sink mixer for mixing hot and cold water, bedding in cement morter to dwarf wall or including CP Waste , PVC Down pipe etc and fixing cantilever brackets and connecting union to pipe overall size495mmx 420mm bowl size 410mm x330mm x160mm etc compete all as specified and directed.

Item No 161 S&F stainless steel kitchen plate rack of AISI 316 grade with four shelves made out of stainless steel sheets 1 mm thick over all size 90x90x25cm complete all as specificed and directed.

Item No 162 S&F Chromium plated tubular towel rail, 20mm dia, ‘D’ type 60cm long between flanges of brass chromium plated and fixed with brass screws all as specified and directed.

Item No 163 S&F in repairs 15 mm bore Angle valve cast copper alloy Chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed.

Item No 164 S&F wall mixture 15 mm bore cast copper alloy Chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed.

Item No 165 S&F in repairs 15mm bore bib taps fancy type of Chromium plated high pressure screwed for iron pipe and fixed etc. complete all as specified and directed.

Item No 166 S&F in repairs CP brass shower rose 150mm dia with chromium plated arm fixed to 15mm pipe of revolving type complete all as specified and directed.

Item No 167 S&F in repair Stainless steel grating 100mm dia of best quality as approved by GE including fixing in CM 1:4 to floor/nahani traps etc complete all as specified .

Item No 169 S&F PVC connection 15 mm bore and 60cm long with PTMT nuts complete all as specified and directed.

Item No 170 S&F in repair PVC connection 15 mm bore and 45cm long with PTMT nuts complete all as specified and directed.

Item No 171 S&F PVC connection 15 mm bore and 30cm long with PTMT nuts complete all as specified and directed.

Item No 172 S&F CP connection 15 mm bore and 37.5cm long with PTMT nuts complete all as specified and directed.

Item No 173 S&F 32mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed

Item No 174 S&F 40mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

Item No 175 M&L PCC 1:5:10 type E-2 using 40 mm graded brick aggregate as in filling under sunken floors etc complete all as specified and directed.

Item No 176 M&L for Providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 to match the existing apron complete all as specified and directed.

Item No 177 M&L for Post Construction anti termiteTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor complete all as specified and directed.

Item No 178 M&L Cement concrete 1:2:4 type B1(using 20 mm graded crushed stone aggregates) in roof kerbs or mud stop rounded or chamfered on edge etc complete all as specified and directed.

Item No 179 M&L for cutting holes on brick or concrete surface exc half brick but n.exc one brick wall for including making good of disturbed surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate complete all as specified and directed.

Item No 180 S&F IInd class Hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed all as specified and directred.

Item No 181 S&F 35mm thick 2nd class Hard wood rail & style (factory made) plain, framed, panelled shutter (two panel) with lock rail & panel of 12mm veneered particle board with commercial veneering on both sides. The size of rail & style as per IS :1003 (Part I), Kilan seasoned & chemicals pressure treated, complete all as specified.

Item No 182 M&L for followings :- (i) Removing plaster & finishes all around the coloumns, slabs & beams (on all four sidescription of column to full height , three sidescription of beam to entire span & bottom of slab to area as directed) (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible) (iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed) (iv) Cleaning exposed concrete substrate by using water jet. (v) Removing visible rust along the length of reinforcement using hand tools as approved. (vi) M&L for providing rust proof /anti corrosive treatment to bars as per manufacturers instrucions. (i) cleaning of all exposed bars (new & old) alround (ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer (iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating. (The Engr-in-charge may order sand blasting if rust is approved) (vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed.

Item No 183 M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

Item No 184 Add or deduct for each 2mm thick or part there of over or under 25mm thick PMM (Polymer modified membrane).

Item No 185 M&L for treatement of core concrete when found to be porous/honeycombed :- (i) Marking the area in marker as directed by the Engr-in-charge. (ii) Drilling holes of upto 16mm dia in an orthogonal grid on exposed cone of member @ 150 mm c/c both way, depth of the hole shall be about 60% of the element thickness. (iii) clean the drill hole using compressed air removing the dust/dirt. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole with the annular space around the nipple sealed with epoxy putty. It shall be ensured that the injected grount does not leak. (v) Allow the nipple to cure for 24 hours. (vi) Injecting " Resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note : pressure shall be in the range of 2-3 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardenere shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly. (vii) Allow entire effected surface to cure for 24 hours. (viii) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (ix) cleaning exposed surface of substrate off any dust /loose material after ageing of the grout as recommended by manufactuer.

Item No 186 M&L for Providing & Pouring Micro concreting M-40 grade :- (i) Dry concrete substrate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound concrete substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above pour Micro concreting M40 grade approved Make using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be repaired in RCC beams & columns etc,. Adding of aggregates will be permitted only as per manufacturer’s recommendation without compromising the strength. The rate shall include cost of all materials (except re-bar) labour charges for mixing, pouring concrete, cost of tools, lead & lift of materials, transportation etc., to carry out the complete work complete all as specified and directed. Note : The cost of micro concrete M-40 grade & Epoxy bond coat is inclueded in this item.

Item No 187 M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 8 mm dia bar - drilling length 80 to 100 mm - 384 Nos Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar of apparoved make with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

Item No 188 M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 16 & 20 mm dia bar - drilling length 160 to 180 mm - 700 Nos Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar of approved make with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

Item No 189 M&L for use & waste of form work using steel sheets , steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period complete all as specified and directed. Note : Form work shall be 100% leak proof. For purpose of payment area in touch with concrete shall be measured.

Item No 190 M & L for providing guniting in two layers over steel welded mesh 2mm dia of wire and total aperture 75mm thickness of gunite n.exc 25mm thick (average thickness) using cement mortar 1:3 with OPC 43 grade cement mixed with polycrete admixture @ 2% by weight of cement or as per manufactures instructions and finally applying cement plaster over gunited surfaces of required thickness to give an even, uniform and smooth finish conforming to proper geometrics in cement mortar 1:4 to match with the existing surface as in side and soffits of slabs, chajjas, fins, facias, parapets, columns and beams etc complete including necessary scaffolding, shuttering necessary chased to brick work or RCC members at any height upto four storey buildings incl removing of small trees welded with the existing reinforcement. The cost of welded with the existing reinforcement is deemed to be included in the quoted rate.

Item No 191 M&L Screed bedding 20mm thick plaster in CM 1:4 on roof finished even and fair using integral water proofing admixtuire.(Note : Supply only water proofing admixture shall be measured and paid separately) complete all as specified and directed .

Item No 192 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and the sheet should be embedded in to the wall to a depth of 25mm and the surfaces to be plastered and made good complete all as specified and directed.

Item No 193 S&F Framed bracket of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary,gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Item No 194 M&L for Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, inluding finishing the joint of face board with specially formulatted jointing compound and 48 mm wide fibre tape to provide seamless finish including GI frame work for seamless ceiling comprising of GI perimeter chennel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylone sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm susoended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with clips of 10.5mm fixed to the intermediate channel at 457mm centre to centre.Hangers 6mm dia GI (upto 1200mm length adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flate 40X30mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed.

Item No 195 M&L for complete removal of existing treatment on surfaces of walls/ceilings by scrapping down with mechanical grinder on old walls as per the specification of manufacturers instructions of paints/OBD complete all as specified and directed.

Item No 196 M&L for preparation of newly plastered or unplastered surfaces on walls complete all as specified and directed.

Item No 197 All as per item No. 196 above but on old surfaces of walls

Item No 198 M&L for preparation of newly plastered or unplastered surfaces on ceilings complete all as specified and directed.

Item No 199 All as per item No. 198 above but on old surfaces of ceilings.

Item No 200 M&L for old plastered surfaces of walls and applying two coats of white wash on walls complete all as specified and directed.

Item No 201 M&L for old plastered surfaces of ceilings and applying two coats of white wash complete all as specified and directed.

Item No 202 M&L for applying three coats of white wash on newly plastered surfaces of walls complete all as specified.

Item No 203 M&L for applying white wash three coats on newly plastered surfaces of ceiling complete all as specified and directed.

Item No 204 M&L for old plastered surfaces of walls and applying two coats of Oil bound distember on walls complete all as specified and directed.

Item No 205 M&L for applying two coats of Oil bound distember over a coat of primer on newly plastered surfaces of walls including preparation of surfaces complete all as specified and directed.

Item No 206 M&L applying two coats of weather coat paint on walls over a coat anti alkaline primer on new plastered surfaces including preparation of new surfaces complete all as specified and directed.

Item No 207 M&L for applying 2 coats of Chalk whiting, on plastered surfaces, preparatory to distempering on newly/old plastered walls of including preparing the surface with even and smooth complete all as specified and directed. (Note : Wall putty to be procured from manufactures directly)

Item No 208 S&F Drappery curtain rods decorative type stainless steel 25mm nominal dia of approved quality(Make VISTA) (3mm wall thickness) including fixing of two number decorative brackets fixed in brick/concrete wall, Two number of latto on both ends of curtain rods ( The length of each curtain rod will be 1.00m to 1.50m long) complete all as directed and specified.

Item No 209 M&L for 6mm thick bevelled edge looking mirror of size n exc 0.6 sqm each with teak wood beadings of 50 mm width round allround and plywood backing complete all as specified and directed. Note : The rate quoted by the contractor inclusive of providing two coats of melamine polish for frame/beading, necessary fixing CP brass screwes and accessories.

Item No 210 Dismantling and refixing of existing steel windows of any description after reparing inclu removing of old glass panes and refixing after necessary cuttings carefully including fixing of frames, sash bars with angles etc all as specified and directed. Note : replacement of wirenesh and already damaged glass panes will be measured and paid separately under respective items.

SEWAGE DISPOSAL

Item No 211 Excavation in trenches, any type of soil n exc 1.5 m wide and not exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc n exc 10 sq m on plan and n exc 1.5 m in depth and getting out complete all as specified and directed .

Item No 212 S&F DWCPE(SN4) 150mm dia (Internal Dia) pipes,snap fit coupler and rubber ring incl testing and laid and properly jointed laid in trenches to a level on concrete bed complete all as specified. Note : The DWCPE (SN4) pipe shall conform to IS 14930 and of best quality as approved by GE. The DWCPE shall consisst of two layers. The outer layer will be corrugated and inner layer shall be plain and smooth. DWCPE pipe and fitting with the scope of this specification shall be so designed and constructed that in normal use their performance is reliable and without damage to the user or surrounding and shall be laid as per manufacturer instructions.

Item No 213 Returning filling in incl spreading, leveling watering and well ramming in layers n.exc 25 cm complete all as specified and directed.

Item No 214 Removing excavated soil to a distance n. exc 50 mtr and depositing were directed at a level n. exc 1.5 mtr above the starting point.complete all as specified and directed.

Item No 215 M&L for Cutting of exising 150 mm dia manholes for connecting new drains making good to pipe and rendering cutting out exising benching for and forming benching for and forming branch channel (1/2 round or 3/4 section ) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching required complete all as specified and directed .

Item No 216 M&L for Brick work sub class ‘B’ bricks state or curved on plan built in cement mortar 1:4 using old size bricks complete all as specified and directed.

Item No 217 M&L for Cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate ) as in foundation manholes.complete all as specified and directed.

Item No 218 M&L PCC 1:2:4 type B1 using 20 mm graded crushed stone aggregates in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and directed.

Item No 219 M&L for precast factory made manhole cover, area of each cover n.exc 0.60 Sqm, 100mm thick with SFRC concreting including grove and hook arrangement for lifting and placing in position and sides covered by MS sheet complete all as specified and directed.

AREA DRAINAGE

Item No 220 M&L for Cement concrete 1:2:4 type B-2 as in surface channals or drains all as specified and directed.

Item No 221 M&L for Brick work sub class ‘B’ bricks straight or curved on plan built in cement mortar 1:4 using old size bricks complete all as specified and directed.

ROAD, PATH & CULVERT

Item No 222 M&L cement concrete 1:4:8 type D2 (40mm graded stone aggregate) as in sub base 75mm thick, complete all as specified and directed.

Item No 223 M&L for Sand filling (sand cushioning) under floors or in foundations including watering and consolidations complete all as specified and directed.

Item No 224 M&L machine rubber moulded pressed precast concrete interlocking paver block with PU coating any shape and size conforming to IS 15658-2006 of 85 mm thickness M-40 Grade with grey cement and pigment all as specified and directed.

INTERNAL ELECTRIFICATION

Item No 225 Taking down carefully copper/aluminium point wiring from wooden battan or conduits (light, fan, socket or power) complete including (fittings such as switches, ceiling roses, pendants, regulator, sockets etc. to be measured separately) and making good disturbed surfaces of walls, floor etc.

Item No 226 Taking down old MCCB , TPN DBs , SPN DBs, & main switch/ enclosure box of any make and type from the site and making good surface complete all as specified and directed.

Item No 227 Taking down old submain wiring of any size and make from the site and making good surface complete all as specified and directed.

Item No 228 Taking down old unsv light fitting of any size and make from the site and making good surface complete all as specified and directed.

Item No 229 Taking down old carefully unserviceable recess mounted 2"x2" (4x14 watt) light fitting of any make and type from the pop hard pop false ceiling without damaging the existing false ceiling structure and making good the disturbed surfaces around the light fitting with POP and matching with the existing colour complete all as specified and directed.

Item No 230 M&L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through and including non-metalic rigid new PVC conduit medium grade ISI Marked not less than 20 mm dia and all conduit accessories concealed in wall on surface in ceiling/fixed to roof/truss/columns etc and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuty, fabricated modular metal flush box, concealed in walls with suitable modular inner and outer plate for housing switches , socket out let and fan regulators etc, complete all as specified.

(a) One light /Ceiling fan/exhaust fan point controlled by one switch.

(b) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on same board

(c) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on independent board.

(d) One bell point controlled by one bell push.

(e) One light point controlled by two Nos two way switches

Item No 231 M&L point wiring with PVC unsheathed multi stranded copper conductor cable 4 Sqmm FRLS 1100 Volts in new PVC concealed conduit medium grade ISI Marked not less than 20 mm dia in new M S steel terminal boxes modular including one run of using 4 sqmm FRLS 1100 Volts copper conductor cable as earth continuity connected to common earth for one 15 A switch socket power point, complete all as specified and directed.

Item No 232 S&F switch Modular type 6 Amps one way ISI marked 230V AC complete all as specified and directed.

Item No 233 S&F switch modular type 6 amp SP two way ISI marked complete all as specified and directed.

Item No 234 S&F Modular socket outlet 5 pin 6 Amp socket 2 module ISI marked complete all as specified and directed.

Item No 235 S&F switch bell push Modular type 6 Amps 1W-1 module, ISI marked 230V AC complete all as specified and directed.

Item No 236 S&F switch Modular type 16 Amps one way ISI marked 230V AC complete all as specified and directed.

Item No 237 S&F Modular socket outlet 5 pin 6/16 Amp universal socket 2 module complete all as specified and directed.

Item No 238 S&F Modular five stepped type electronic fan regulator 2 module ISI marked 230V AC complete all as specified and directed.

Item No 239 S&F bell electric (ding dong) 230 volt, SP complete all as specified and directed.

Item No 240 M&L point wiring with PVC insulated FRLS 1100 Volts unsheathed cable 1.5 Sqmm multistranded copper conductor and drawing concealed in wall & including nonmetalic rigid new PVC conduit medium grade ISI Marked not less than 20 mm dia of conduit, terminal box of 1.6 mm thick and 3 mm thick hylam sheet cover for terminal boxes also including porvision of earth wire PVC insulated FRLS 1100 Volts unsheathed 1.5 sqmm stranded copper conductor single core cable connected to common earth dolly the following:-

(a) One light/fan/bell point controlled by one by one way switch.

(b) One light point controlled by two, two way switch.

(c) One 3 pin socket outlet 5 hole 5 Amp independent board including PVC unsheathed copper conductor 1.5 Sqmm cable as earth wire connected to common earth and to earth dolly. Note:- Socket & switches to be measured and paid separately.

(d) -ditto- as above item No 255 (c) above but on same board.

Item No 241 S&F One power point with insulated stranded copper conductor cable 4 Sqmm single core for 3 pin 15 Amp switch socket and PVC insulated FRLS 1100 Volts unsheathed copper conductor 4 Sqmm in and including new PVC conduit medium grade not less than 20 mm dia, stranded conductor as earth wire connected to dolly complete all as specified and directed.

Item No 242 M&L for submain wiring with two single core PVC insulated FRLS 1100 Volts unseathed stranded copper conductor cable 4 Sqmm in and including new PVC conduit medium grade not less than 20 mm dia, for submain wiring and connection complete FRLS 1100 volts unsheathed stranded copper conuctor cable of 4 Sqmm size stranded conductor as earthwire complete all as specified and directed.

Item No 243 M&L for submain wiring with two single core PVC insulated FRLS 1100 Volts unseathed stranded copper conductor cable 6 Sqmm in and including new PVC conduit medium grade not less than 20 mm dia, for submain wiring and connection complete FRLS 1100 volts unsheathed stranded copper conuctor cable of 6 Sqmm size stranded conductor as earthwire complete all as specified and directed.

Item No 244 M&L for submain wiring with two single core PVC insulated FRLS 1100 Volts unseathed stranded copper conductor cable 10 Sqmm in and including new PVC conduit medium grade not less than 20 mm dia, for submain wiring and connection complete FRLS 1100 volts unsheathed stranded copper conductor cable of 10 Sqmm size stranded conductor as earthwire complete all as specified and directed.

Item No 245 S&F switch piano flush type 5 Amp SP one way ISI marked complete all as specified and directed.

Item No 246 S&F switch piano flush type 15 Amp SP one way ISI marked complete all as specified and directed.

Item No 247 S&F bell push,flush type,5 amp ISI marked complete all as specified and directed.

Item No 248 S&F socket outlet 5 pin 5 Amp flush type ISI marked complete all as specified and directed.

Item No 249 S&F socket outlet 2 in 1,3 pin 5/15 Amps ISI marked complete all as specified and directed.

Item No 250 S&F ceiling rose 3 phase PVC polycorbonate, isolated body complete all as specified and directed.

Item No 251 S&F electronic fan regulator 5 step ISI marked connecting complete all as specified and directed.

Item No 252 S&F angle Lamp holder with metallic ring, PVC/Polycorbonate type with back plate complete all as specified and directed.

Item No 253 S&F LED bulb 12 watts, 1200 lumens output, 6500K suitable for B-22 base complete all as specified and directed.

Item No 254 S&F switch piano flush type 5 Amp SP two way complete all as specified and directed.

Item No 255 M&L for earthing complete with galvanized steel earth plate 600x600x6mm thick buried vertically in ground to depth not less than 2.25 mtr below ground level, with top edge of the plate not less than 1.50 mtr below normal ground level, connected to earth lead GI 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and connection to main switch board of panel, including watering pipe GI 20 mm bore light grade 15mm bore for earthing lead, wire mess, funnel, salt, charcoal dust, excavation and refilling pit with PCC 1:2:4 type B1(using 20mm dia stone aggregate) reinforced with 6mm dia round bar @ 75mm cement concrete both always with MS handle 12mm dai and frame all as shown in electric plate No 3 of SSR Part I (2009) including testing on completion, complete all as specified and directed.

Item No 256 M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recessed or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc 4 mm dia galvanised or steel wire complete all as specified and directed.

Item No 257 S&F MCB DB SPN 12 way Horizontal, IP - 43 Protection double door 240 V AC 50Hz with for MCB SPN as incomer and SP MCBs as out going with tinned copper bus bar ,neutral link earth link complete all as specified and directed.

Item No 258 Supply and fix MCB DB SPN 8 way Horizontal, IP - 43 Protection double door 240 V AC 50Hz with for MCB SPN as incomer and SP MCBs as out going with tinned copper bus bar ,neutral link earth link complete all as specified and directed.

Item No 259 S&F MCB SPN 63 Amps 240 volts 10 KA 50 HZ 'C' curve complete all as specified and directed.

Item No 260 S&F MCB SPN 40 Amp "C " curve complete all as specified and directed.

Item No 261 S&F MCB SP 6 to 32 Amp "C" curve complete all as specified and directed.

Item No 262 Supply and fix LED batten luminaries surface mounted 4 feet system wattage of 20-22 Watts with lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD<20%, colour temperature - 6500K, surge protection 3KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 Degree C, system efficacy at luminaries level > 105 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete. Note- All the above mentioned specs will be verified through LM 79 and LM 80 report of NABL accredited Lab before supply of LED fixtures.

Item No 263 S&F LED batten luminaire surface mounted 2 feet system wattage of 9-10 Watts and not less than 900 lm system lumen output with life time of 50000 burning hours with 70% of its initial lumen maintained. CRI > 80, power factor > 0.95, THD < 10%, color temperature > 6500 K , surge protection 2.5 KV in CM IP- 20 protected meets LED IS specifications, short circuit and over circuit protection, voltage range - 150 to 270 volts AC, temperature range 0 to 50 Degree C, and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete all as specified and directed. Note- All the above mentioned specs will be verified through LM 79 and LM 80 report of NABL accredited Lab before supply of LED fixtures.

Item No 264 S&F 10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary is > 100 lm/W with a life class of 50,000 burning hours at L70 criteria, Power Factor >0.95, driver with Voltage range 150-270V, Temperature range 0 to 50 Deg, Driver efficiency >85%, THD<20%, CRI>80, Color Temperature-6500K, Surge protection of 4.0 KV, including connecting up with necessary PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete all as specified and directed. Note- All the above mentioned specifications will be verified through LM 79 and LM 80 report of NABL accredited Lab before supply of LED fixtures.

Item No 265 Supply and fix surface ceiling mounted, round LED down light fitting 15 watts with die cast aluminium housing and system wattage of 15W, system efficacy at luminary level ≥ 100 Lumens/watt, 50000 burning hours, 6500K color temperature with CRI >80, Power Factor > 0.90, Driver should meet IEC compliant for safety with multi stage high Isolate CC-CV operated driver with voltage variation range - 150 to 270 Volts AC, and surge protection of 3 KV, and including connecting up with PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete.15 watts Note- All the above mentioned specifications will be verified through LM 79 and LM 80 report of NABL accredited Lab before supply of LED fixtures.

Item No 266 Supply and fix recessed mounting LED panel 2"x2" made of crca sheet aluminium duly power coated with high efficient LED and glaire free UGR<19 full opal diffuser , IP 20 Suitable for 36 watt,230 volts ,50 Hz AC Supply, THD<10%, 110< lm/watt Neutral White, with electronic driver and including all fixing accessories complete. Note- All the above mentioned specifications will be verified through LM 79 and LM 80 report of NABL accredited Lab before supply of LED fixtures.

Item No 267 S&F surface ceiling mounted,squre LED down light fitting size (1 ft x 1 ft), 12 watts with die cast aluminium housing and system wattage of 15W, system efficacy at luminary level ≥ 100 Lumens/watt, 50000 burning hours, 6500K color temperature with CRI >80, Power Factor > 0.90, Driver should meet IEC compliant for safety with multi stage high Isolate CC-CV operated driver with voltage variation range - 150 to 270 Volts AC, and surge protection of 2.5 KV, and including connecting up with PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete all as specified and directed. Note- All the above mentioned specifications will be verified through LM 79 and LM 80 report of NABL accredited Lab before supply of LED fixtures..

Item No 268 S&F in repair factory made epoxy powder coated Distribution Board TPN-4 ways with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with knockouts and suitable for one TPN- MCCB 125/160 Amp as incomer and 40 to 63 Amp SP MCBs outgoing complete all as specified and directed and conforming to IS : 8623.

Item No 269 S&F in replacement MCCB 125 Amps, 16 KA , 4P, complete all as specified and directed.

Item No 270 S&F 45 W High efficient LED Street light fitting with pressure die cast LM6 Aluminum housing and has lenses specially designed for Street Lighting with polycarbonate cover. System level efficacy of the Luminarie is 110lm/W with a life class of 50,000 burning hours at L70. The color temperature is around 6500 K with a color rendering index of 70. The luminaire is IP:66 protected with IK05 impact resistance. It has an electronic driver complaint to IEC safety standards with a power factor>.0.9, voltage variation range 120-270V, THD<10%, High and low protection along with a surge protection of 4 KV including provision of 40mm dia GI light grade pipe1.5 meter length bend to shape and necessary clamps etc for fixing the light fittings on pole fixed complete all as specified and directed. Note- All the above mentioned specifications will be verified through LM 79 and LM 80 report of NABL accredited Lab before supply of LED fixtures.

Item No 271 Taking down carefully the existing ceiling fan of 1200/1400 mm from its position after disconnecting electric connection and deposits in MES Store complete all as specified and directed.

Item No 272 Supply and fixing ceiling fans three blade, Robust and reliable inverter motor (brush less DC Motor) powered by ECM technology, BEE 5 star rating for energy saving, rated Air delivery >220cum/min, AC single phase 230/240 V of size 1200 mm sweep including making connection with three core flexible, copper cable PVC insulated of suitable length, complete all as directed.

Item No 273 S&F fresh air fan PVC body air delivery > 800 CMH , 5 number of blades, AC single phase 230/240 V of size 250 mm sweep with louvre fixed complete with suitable size ply by cutting into suitable size as required complete all as specified and directed.

Item No 274 S&F sheet metal enclosure single pole and Neutral with a two pin earth plug and socket complete with a MCB SP 20 Amp 230 volts, 50 Hz, 10KA breaking capacity complete all as specified and directed.

Item No 275 S&F sheet metal enclosure single pole and Neutral with a two pin earth plug and socket complete with a MCB SP 10 Amp 220 volts, 50 Hz, 10KA breaking capacity, including fixing completly in wall with sutable sand and cement, complete all as specified and directed.

Item No 276 S&F water heater storage type Geyser vertical type with suitable size of fastner and including provision and connecting up of SS braidedpipe with adopter for inlet and outlet water connection having edjustable knob for temperature control and, inner tank material of superior glass line tank and outer body material ofABS with high pressure with standing enabling (up to 8 bar pressure) capacity 25 Ltrs, having heating element 1.5 KW and not less than 3 star rating, suitable for ,230 volt, 50 Hz electric supply complete all as specified and directed.

Item No 277 S&F exhaust fans AC single phase 230/240 V of size 300 mm sweep, Air flow rate > 900 cum/min, Bird screen for protection against birds, double ball bearing, metal body with louvre metal body with louvre for fixing of exhaust fan complete all as specified and directed.

Item No 278 M&L telephone Point wiring complete with single pin 0.61mm dia copper conductor cable telephone pain taped and rip conforming to ITD specification D-3003 and ITI-113C/114C cable PVC insulated drawn though PVC concealed conduit not less than 20 mm dia for one 2 pin telephone socket out let on independent modular type board complete all as specified and directed.

Item No 279 S&F in repair RJ-11 Telephone socket with transparent shutter 1 module on phenolic laminated sheet etc as required complete all as specified and directed.

Item No 282 M&L for XLPE insulated, heavy duty under ground electric cable with stranded aluminium conductor,1100 volts grade of cross sectional area 25 Sqmm, 3.5 Core laid in trenches/fixing on wall/poles or passing through pipe including connecting up with suitable glands, lugs, nuts and bolts wherever required and testing complete all as specified and directed.

Item No 283 Supply and lay cable in replacement XLPE insulated screened PVC bedded, galvanized steel strip and wire armoured , electric power cables (heany duty) 1100 volts grade with stranded alumimium conductor of size 16 Sqmm 4 core complete all as specified and directed.

Item No 284 S&F GI Pipe 32 mm bore light grade, for laying in road crossing/ fixing of vertically complete all as specified and directed.

Item No 285 Excavation in trenches n.exc 0.45 m wide and n.exc 0.60 m depth for laying of LT cables etc. and getting out in soft/loose soil complete all as specified and directed.

Item No 286 Returning, filling in, including soreading levelling, watering and well ramming in layers not exc 25 cm depth in soft/loose soil complete all as specified and directed.

Item No 287 Removing excavateed material to a distance not. Exc 50 m and deposting where directed at a level not. Exc 0.6 m above the starting point complete all as specified and directed.

Item No 288 Supply and spreading clean dry sand in trenches for cushioning/cable protection complete all as specified and directed.

Item No 289 Supply and laying sub clas 'B' Bricks of old size ( 23 x 11 x 7 cm) laid along alignment of cable as protection to cable in trenches complete all as specified and directed.

Item No 290 Supply, installation, testing & commissioning, fabricating wall mounted LT panel board indoor type of size 900x1200x200mm (approx) made out of 2 mm thick CRCA sheet powdered coated LT panel board of suitable size and suitable for 3 phase,4 wire, 440 volts, 50Hz AC supply indoor cubical type, dust and vermin proof, IP 54 wall/ Floor mounting type suitable for indoor applications, having bus bas chamber with 200 Amps duly insulated copper bus bar, cable chamber with cable entry glands separate switch gear including providing space for the following switch gear & controls complete all as specified and directed.

Item No 291 Taking down carefully the existing Exhaust fan of 300mm rom its position after disconnecting electric connection and deposits in MES Store all as specified and directed.

Item No 292 S&F Wall mounted fans AC single phase 230/240 V, of size 400 mm sweep, aerodynamic design, air delivery >70 CMM, 3 blade , thermal overload protected motor, speed RPM 1400, Sturdy and shock proof body for fixing of wall fan complete. all as specified and directed.

Item No 293 S&F indicator, triangular bulkhead red /green colour light 2 module includings suitable size of modular metal flush box and modular cover for mounting for light complete all as specified and directed.

Item No 294 M&L for sub main wiring with two single core FRLS stranded copper conductor cable 1100 volts grade of size 1.5 sqmm and one single core FRLS stranded copper conductor cable 1.5 sqmm for earth wire in and including New PVC concealed conduit medium grade ISI Marked not less than 20 mm dia with all fittings complete all as specified and directed.

Item No 295 S&F GI Pipe 32 mm dia Medium grade galvanised with all fittings and fixed complete to existing walls for hanging of ceiling fan 1200 mm sweep complete all as specified and directed.

Item No 296 S&F wall mounted, 5 watt decorative LED picture light fitting complete all as specified and directed.

Item No 297 M&L for breaking the old existing wall and making provn of a round hole for fixing of 300 mm sweep exhaust fan including making good to the disturbed wall/ portion and matching with existing colour complete all as specified and directed.

Item No 298 M&L for earthing of machinery/equipment/panel/installed at power house/subatation, complete with galvanised steel earth palte electrode 600 x 600 x 6 mm thick buried directly in ground (Earth pit not less than 2.5 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to galvanised iron strip 25 x 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth protected by 40 mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electrical plate No.3 of SSR Part-I )2009) and testing on completion, complete all as specified and directed.

Item No 299 Taking down carefully the existing Old U/S Geyser capacity 25 Ltr its position after disconnecting electric & water connection and deposits in MES Store all as specified and directed.

SPECIAL ITEMS

Item No 300 M&L for submain wiring with two single core PVC insulated FRLS 1100 Volts unseathed stranded copper conductor cable 4 Sqmm in and including new PVC conduit medium grade not less than 20 mm dia, for submain wiring and connection complete FRLS 1100 volts unsheathed stranded copper conuctor cable of 4 Sqmm size stranded conductor as earthwire complete all as specified and directed.

Item No 301 S&F sheet metal enclosure single pole and Neutral with a two pin earth plug and socket complete with a MCB SP 10 Amp 230 volts, 50 Hz, 10KA breaking capacity complete all as specified and directed.

Item No 302 S&F in repair sheet metal enclosure single pole and Neutral with a two pin earth plug and socket complete with a MCB SP 10 Amp 220 volts, 50 Hz, 10KA breaking capacity, including fixing completly in wall with sutable sand and cement, complete all as specified and directed.

Item No 303 S&F water heater storage type Geyser vertical type with suitable size of fastner and including provision and connecting up of SS braidedpipe with adopter for inlet and outlet wwater connection having edjustable knob for temperature control and, inner tank material of superior glass line tank and outer body material of ABS with high pressure with standing enabling (up to 8 bar pressure) capacity 25 Ltrs having heating element 1.5 KW and not less than 3 star rating, suitable for ,230 volt, 50 Hz electric supply complete all as specified and directed.

Item No 304 S&F water heater storage type Geyser vertical type with suitable size of fastner and including provision and connecting up of SS braidedpipe with adopter for inlet and outlet wwater connection having edjustable knob for temperature control and inner tank material of superior glass line tank and outer body material of ABS with high pressure with standing enabling (up to 8 bar pressure) capacity 50 Ltrs having heating element 2 KW and not less than 3 star rating, suitable for ,230 volt, 50 Hz electric supply complete all as specified and directed.

AMIT ASSOCIATES

Third Wave Services Pvt Ltd