REPAIR/MAINT OF INTERNAL WIRING, LED LIGHT FITTING WITH OTHER ALLIED WORK IN OLD PROJECT AREA UNDER AGE(I) AF STN MANAURI

Amount

Taking down carefully point wiring (light, fan, socket or power) complete with fitting such as switches, ceiling roses, lamp holder, sockets, fan regulators, wooden terminal box plastic laminated sheet cover from TW battens including TW batten or drawing from existing conduit non-metallic removing including TW batten all as specified and as directed by Engr-in-Charge

M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade FRLS PVC cable IS:694 with multi stranded copper conductor of size 1.5 sqmm (Nominal area) drawn through and including rigid PVC conduit/ metelic conduit ISI marked not less than 20 mm dia with all PVC conduit fittings such as Tees, elbows, bend, reducers etc, concealed conduit wiring fixed on wall/ on ceiling with GI saddles, GI screws, rowel plugs (surface conduit wiring) with all fittings including tee, junction boxes and provision of pressed steel terminal box 1.25 mm thick of suitable size with 3 mm thick plastic laminated sheet cover for mounting modular / piano accessories such as switch sockets and regulators and drawn continuous earth wire with and including PVC insulated unsheathed 1100 volts grade cable with multi stranded copper conductor of size 1.5 sqmm (Nominal area) connected to earth dolly complete all as specified and as directed by Engr-in-Charge for the followings:- Note :- (i) The cost of chases cutting on wall for concealing conduit, boxes, plate etc are included in the unit quoted rate. (ii) Switches, sockets, etc shall be measured and paid for separately.

(a) one light/fan/bell point controlled by one switch

(b) one 3 pin 5 amps socket out let on same board controlled by one switch

(c) one 3 pin 5 amps socket outlet on independent board controlled by one switch

M&L for point wiring for controlled by one switch with PVC unsheathed single core multistranded copper conductor cable of size 2.5 Sqmm (nominal area) in and including PVC conduit 20 mm dia by cutting chases in walls by cutter and making good the surface in CM 1:3 and to the original specification and PVC cassing capping on ceiling for steel structure/surface conduit with clamps, gutties etc for RCC ceiling with including cast iron/pressed steel terminal boxes including providing new 3 mm thick plastic laminated sheet cover (Hylem) including one run of PVC insulated FRLS copper conductor cable of 1.5 Sqmm with green insulation as earth dolly for 6 pin, 16 Amp socket outlet on Independent board.

M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 sqmm (Nominal area) , laid/drawn through & including suitable size PVC casing capping with necessary fittings/ accessories fixed on walls/ ceiling by means of metalic sleeve/dash fastener with cadmium plated iron screws all as per ISI including sunk type pressed steel terminal boxes for mounting, fittings like switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet top covers concealed in walls etc and drawing continuous earth wire with and including PVC insulated unsheathed 1100 volts grade cable with multi stranded copper conductor of size 1.5 sqmm (Nominal area) connected to earth dolly complete all as specified and as directed by Engr-in-Charge for the followings:-.

(a) one light point or one fan point controlled by one switch

(b) one 3 pin 6 amps socket out let same board controlled by one switch

(c) one 3 pin 6 amps socket outlet on independent board controlled by one switch

One bell point controlled by one bell push

Material and labour for providing point wiring by using cable of size 2.5 sq.mm (nominal area) single core PVC insulated flame retardant un-sheathed multi-stranded copper conductor cable (maintaining colour code), 1100 volts grade with and including PVC casing capping as required at site but not less than 20 mm including suitable accessories and fittings/fixtures and PVC box as required at site for mounting switches, sockets, etc. for one socket outlet 3/6 pin 15 amps including 1.5 Sq.mm PVC insulated unsheathed multi-stranded flame retardant copper conductor cable green in colour for earth continuity & connected to common earth dolly complete all as specified & directed.

S&F of switch piano flush type 5/6 Amps single pole one way 230/250 volts complete for one light/fan point/ 5 amp socket outlet controlled by one switch all as specified and directed by Engr-in-Charge

S&F for socket outlet 2 in 1 3 pin 5 Amps flush type 230 volts AC circuit on same board complete all as specified and directed.

S&F switch socket combination 2 in 1 3/5 pin 5 Amps 240 volts flush type multipurpose complete all as specified and as directed.

S&F switch socket combination 2 in 1 5/6 pin 5/6 Amps and 15/16 Amps flush type 240 Volts universal complete all as specified and as directed.

S&F Bell push flush type single pole one way 5 Amp (ISI Marked)

S&F electronic fan regulator, stepped type, socket type, 230 volts, 120 watt, ISI marked including connection.

S&F Modular switch 6 Amp 250 V AC one way one module Make : Legrand /Schneider /Anchor/SSK

S&F Modular switch 20 Amp 250 V AC one way with indicator one module Make : Legrand /Schneider /Anchor/SSK

Supply and fixing in replacement modular socket 6 A, 2/3 pin combined 2 module.

S&F Modular Socket 6A/16A - 2/3 pin combined 2 module Make : Legrand /Schneider /Anchor/SSK

S&F modular Fan regulator step type, 120W - 2 module Make : Legrand /Schneider /Anchor/SSK

S&F Modular bell push switch 6 Amp 250 V AC one way one moduler of Make - Legrand (Arteor) or equivalent in Schneider (Opale)/Anchor(Ave).

Supply and fix Metal flush mounting box of 1/2 Module complete all as specified and as directed. Make : Legrand /Schneider /Anchor/SSK/Standard

Supply and fix Metal flush mounting box of 3 Module complete all as specified and as directed. Make : Legrand /Schneider /Anchor/SSK/Standard

Supply and fix Metal flush mounting box of 4 Module complete all as specified and as directed. Make : Legrand /Schneider /Anchor/SSK/Standard

Supply and fix Metal flush mounting box of 6 Module complete all as specified and as directed. Make : Legrand /Schneider /Anchor/SSK/Standard

Supply and fix Metal flush mounting box of 8 Module complete all as specified and as directed. Make : Legrand /Schneider /Anchor/SSK/Standard

Supply and fix Metal flush mounting box of 12/16 Module complete all as specified and as directed. Make : Legrand /Schneider /Anchor/SSK/Standard

S & F white colour modular blanking plate, one module i complete all as specified and directed. Make : Legrand /Schneider /Anchor/SSK/Standard

Supply and fixing in replacement white cover plate with frame 2 module .

Supply and fixing in replacement white cover plate with frame 3 module .

Supply and fixing in replacement white cover plate with frame 4 module .

Supply and fixing in replacement white cover plate with frame 6 module.

Supply and fixing in replacement white cover plate with frame 8 module .

Supply and fix white colour plates with frame for modular switch and socket of 2 x 6 / 2 x 8 module complete all as specified and as directed.Make : Legrand /Schneider /Anchor/SSK/Standard

M&L for ceiling rose, surface Bakelite 65 x 17.50 mm of three terminals PVC/Polycarbonate,isolated body (ISI Marked)

M&L in replacement of unserviceable sub main wiring with two single core FRLS PVC insulated unsheathed stranded copper conductor cable confirmimg to IS-694 with copper conductor of size 6 sqmm and drawing through non rigid metallic PVC conduit (concealed in wall) incl 6.0 sqmm FRLS PVC insulated unsheathed stranded copper conductor cable as earth conductor connected to earth and earth dolly in conduit including connecting to main board including non metallic PVC conduit medium grade not less than of 25 mm dia size with all accessories as specified and directed by Engr-in-Charge. Note : (i) Two single core copper conductor of 6 sqmm including earth wire of 6.0 sqmm including PVC conduit will be measured as single unit length. (ii) The wiring shall be done strictly by following proper colour code- (1) Red, Yellow & blue - for Phase (2) Black - for neutral (3) Green - for Earth

S&F PVC/polycarbonate Angular lamp Holder insulated body with back plate angle type suitable for batten complete all as specified and directed by Engr-in-charge .

Supply and fixing LED Tube light fitting 20 watt 4 feet pre coated CRCA body heavy duty Industrial Batten suitable for Retrofit LED Tube 20 watt including LED tube rod 20 watt self ballasted retrofit lamps with thermoplastic body 270 degree wide distribution CCT 6500 K Cat Part No of Polycab for LED Tube rod LTU0101005 and Batten cat Part No PID0502001 or Havells Cat Part No for LED Tube Rod 20 watt LHLDDBXEUL7Z022 and Batten Cat part No LHFYBWP1TB1W020 or Crompton Cat Part No for LED Tube Rod LT8-20-865(2) and Batten Cat Part No IGP162LT8-16 including fitting fixed on wall/ceiling and connecting up complete with 3 core flexible cable white of size 23/0.0076 including taking down old unsv tube light fitting and making necessary connection complete all as specified and directed by Engr-in-Charge.

Taking down & Re-Fixing only serviceable fluorescent tube light fitting of any type including serviceable tube rod 36/40 watts obtained from Item No. 2.00 here-in-before with electronic ballast, bipin holders, main connector block etc complete with all accessories including connecting the same to ceiling rose with using flexible copper conductor 23/0.0076 complete all as specified and as directed.

Taking down unserviceable main switches, DBs, bus bars chambers including all fittings and fixtures etc complete from existing main boards and removing from site all complete all as directed.

37.Supply & fix Prewired Distribution Board factory made sheet metal enclosure double door distribution board class IP-43 IK 09 with 200 Amp rated copper bus bar 240 Volts 8 way (2 + 6 way) single pole and neutral link cat Part No 607711 of Make - LEGRAND equivalent in Siemens/Schneider complete all as directed by Engineer-in-Charge.

S&F MCB, SPN 40 Amp, 230 volts,10 KA, 'C' series fixed in DBs with all incoming and outgoing connection with proper size lugs including taking down old unserviceable complete all as specified and directed by Engr-in-Charge. Make :- Havells/ L&T/ Indoasian/ Legrand.

S&F MCB single pole (SP) 6 to 32 Amp 240 Volts 10 KA 'C' series with all incoming/outgoing connection with proper size lugs including taking down old unserviceable complete all as specified and directed. Make: Legrand/Siemens/Schneider

Earthing complete with galvanised mild steel earth electrode plate 600 X 600 X 6 mm thick buried directly and vertically in ground connected to galvanised iron earth strip 25x4mm size by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth strip protected by galvanised iron 32 mm bore medium grade pipe with all fittings from the earth electrode fixed along pole with and including 25 x 6mm flat iron clamp, bolts, nuts and washers and watering pipe shall be 20 mm bore GI medium grade from top of the earth electrode to bottom of the earth pit including all excavation and earth work in any type of soil and removal of surplus soil upto 50 metre, PCC pit with pre-cast RCC cover with handle, charcoal/salt, funnel , CI frame etc complete all as directed. Notes :-(i) The concrete pit shall be made in PCC 1:3:6 type C-1, 40mm thick precast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate with suitable MS handle in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. Reinforcement in RCC cover shall be of 8mm dia TMT bars laid @150mm c/c both ways. (ii) Item includes the cost of 7.5 metre GI pipe for protection of earth strip. Any variation in length shall be adjusted through deviation order. (iii) Item includes cost of 7.5 metre earth strips. Any variation in length shall be adjusted through deviation order. (iv) Plate electrode shall be surrounded by adequate quantity of charcoal dust & salt to a packed thickness of 15 cm on all sides.

Taking down old unserviceable bulk head and supply and fixed 10 watt LED Bulk head fitting in engineering diecast aluminium body with clear prismatic diffuser cat part No LBHP-10-CDL of make : CG or equivalent in Philips/Bajaj/Havells including LED 10 watt complete with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 all as specified and directed by Engineer-in-Charge.

Supply and fixing bell ding dong type AC 230 volts single pole

Taking down old unserviceable holder and supply & fix decorative wall mounting type made up of polycarbonate, round shape shade with lamp holders, connectors block including 1 x 09 watt LED blub etc complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable complete cat part No LHDL06160099 Make ; Havells or equivalent in bajaj & philips

Taking down old unsv AC box and Supply & fixed single pole and neutral enclosure surface and flush mounting CRCA sheet steel powder coated with a two pin and earth plug and socket Cat part No DBMPS120SD of L&T or equivalent in Indoasian /Schneider/Siemens/Legrand complete with one single pole MCB 20 Amp 10 KA complete all as directed all as directed by Engineer-in-Charge.

Supply and fixing self ballasted LED Retrofit blub 9 watt with PBT body shell and PC diffuser 240 degree wide distribution including taking down old unsv CFL/GLS blub all as directed by Engr-in-Charge.

Taking down old unsv MCB and supply and fixing MCB TPN 240 Volts 10 KA 'B' series capacity 40 Amp with all incoming/outgoing connection with proper size lugs complete all as directed by Engr-in-Charge.

Taking down old unsv MCB and supply and fixing MCB TPN 240 Volts 10 KA 'B' series capacity 63 Amp with all incoming/outgoing connection with proper size lugs complete all as directed by Engr-in-Charge.

Taking down old unsv fitting and supply and fixing recess mounted LED downlight polycarbonate square shape capacity 18 watt with PDC aluminium body and high transmittance diffuser cat part No LSDEP-18-CDL of Make : CG or equivalent in Bajaj/Havells/Philips including LED 18 watt complete with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 all as specified and directed by Engineer-in-Charge.

Taking down old unsv Tube light fitting and S&F recess mounted LED fitting 36 watt LED luminiare size 2' x 2' with CRCA housing high quality PMMA diffuser suitable for 600 x 600 mm grid ceiling in 5700 K multi angular slim width of the tile makes it seamlessly blend in with the ceiling space. With geometric and aligned designs, the tile can be arranged in a symmetric and abstract way to make the ceiling a piece of art. Cat Part No LCTLRF1-36-TL of Make- CG or equivalent in philips/Bajaj/Havells with all accessories, pre-wired connecting up complete with 3 core flexible cable white of size 23/0.0076 all as specified and directed by Engineer-in-Charge.

Note :- (i) Credit shown in credit schedule of tender document shall be considered by the tenderer while quoting the rates of various items. The same shall be recovered from various payment to contractor before handing over old material. The contract amount shall be arrived at after deduction of Schedule of Credit from the total quoted amount in BOQ. (ii) Make of material shall be as per mentioned in Particular specifications or Appendix 'B' to Particular specifications as approved by AGE (I) AF manauri

M/S R S Traders

shubham construction

Pleiad Complex On

HIMANSHU TRADERS

M/S Garg Sons

Tecj Nirmaan