SPECIAL REPAIR TO BUILDING NUMBER S-55 AT INS KARDIP, KAMORTA UNDER GE (I) CAMPBELL BAY

Amount

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complet all as specified and as directed by Enginer-in-Charge.

S&F pre-painted corrugated galvalume (55% aluminium + 43.5% Zinc+ 1.5% Silicon) steel sheets as in roofing/wall cladding, 0.50mm thick (Total coated thickness), conforming to AS-1397/ASTM A-792 and having yield strength minimum 550 Mpa fixed with self drilling metal coated screw of appropriate size, self taping bolts and fixed as per manufacturers instructions complete all as specified and directed. (Note: The sheet shall be laid with one corrugation side lap and one end lap minimum 150mm all as per manufacturers instructions alongwith wind ties).

S&F Pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S & F for mild steel screw bolts 16 to 20 mm dia of neck (machine made) with hexagonal or square heads at one end and screwed the other or serewed both ends to be fited with washer and one hexagonal or square nut exc 22.5 and n exc 30cm long

Taking down roof trusses, coupled raftersetc, for renewal ao any defective members all as specified and as directed.

S & F for roof trusses (framed), trussed, purlins, crane grantries, rail and fasteninhgs and heavy bracket framing (beam, tee,,angle,, channel, or flat section ) including bracket, etc complet Fe 410-W (Gde-E-250) quaility all as specified.

M&L for preparation of new or previously untreated steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed.

M&L for painting on new steel surfaces n.exc, 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed.

Taking down of cement plaster of any description or thickness/chipping of cement concrete in any situation from brick or concrete surface including raking out of joints, hacking for key scrubbing down with water to received new plaster complete all as specified and directed.

M & L for Rendering 15mm thick (two coat plastering 10+5 with WPT)on fair faces of brick work or concrete surfaces finished even and smooth (without using extra cement) on walls in CM 1:4 complete all as specified and directed.

M &L for preparing new plastered surfaces of wall and applying two coats of cement based paint all as specified and as directed.

M/L for rendering 10mm thick in cement mortar(1:6) on fair faces of solid block or concrete surfaces and finishing fair and even without using extra cement complete all as specified and directed.

M &L for preparing new plastered surfaces of wall and applying two coats of OBD over primer on decorated wall surfaces of any description, complete all as specified.

M &L for preparing new plastered surfaces of wall and applying two coats of anti fungal interior surface of coloumn acrylic emulsion on wall surfaces of any description complete all as specified.

M &L for preparing new plastered surfaces of wall and applying two coats of anti fungal exterior acrylic emulsion on wall surfaces of any description complete all as specified.

Taking down chowkats or frame with shutters (without taking off shutters from the frame), n.exc 1.5 Sqm each complete all as directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame), exc 1.5 sq. m but n.exc 4.0 sq. m each complete all as directed.

Taking down shutters of any description n exc 1 sq. m each all as spcified and as directed

Taking down shutters of any description exc 1 sq. m and n exc 2.0 sq. m each all as spcified and as directed

S&F for 2nd class HW plain, straight chowkats and frames wrought framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and as directed.

S&F 35mm thick, 2nd class HW plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather dged), or of veneered particle board medium density, wood parfticle board with commencial veneers ; suplied and fitted to chowkat all as specified and as directed by Engineer-in-Charge.

S & F flush shutters, 25 mm thick, solid core construction, with block board core and plywood face panels, commencial type on both sides all as spcified and directed.

S&F 2nd class HW, 35mm thick glazed and skeleton shutters, open rebated and rebated for WIndows/ Ventilator and prepared to receive glass or gauge etc., without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for screwing glass / gauge etc., sizes of members of shutters as specified in SSR Part-I, section 8 clause 8.24 (a) all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19 x 19mm MS square tube and 1.2mm wall thickness complete all as specified and as directed.

S&F solid panel PVC door shutter 30mm thick (style) consisting of frame made out of Ms tube for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with a solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either sides and as gap inserts for top and bottom rail paneling of plain colour PVC sheets to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement as per specification and drawing complete all as specified and as directed.

S&F Stainless Steel butt hinges 100mm long, medium weight cold rolled, fixed to timber frame work of doors complete all as specified and directed.

S&F Stainless Steel butt hinges 75mm long, medium weight cold rolled, fixed to timber frame work of doors complete all as specified and directed.

S&F in repairs 150mm length mild steel ordinary rat tail rod of pattern helical springs including roller and roller plate complete all as specified.

M&L extruded aluminium alloy handles 150mm, fabricated type, anodized complete all as specified and directed.

All as per item above but 100mm

M&L aluminium anodized barrel tower bolt of extruded section length of bolt 150mm complete all as specified and directed.

M&L aluminium anodized barrel tower bolt of extruded section length of bolt 100mm complete all as specified and directed.

S&F aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of operature 1.40mm and fixed with aluminium wire staples all as specified and directed.

Hacking out old broken unserviceable glass panes (any thickness size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips and providing and fixing new one complete all as specified and as directed.

S&F 3mm thick figured glass, pin head type and glazing with oil putty in square n.exc 0.5 Sqm in each pane complete all as specified and directed.

M&L for preparation of new or previously untreated wood surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (ordinary tint) over one coat of pink primer complete all as specified and directed.

Taking up or down steel water tubing and connection 15mm dia complete all as specified and as directed.

S&F tubes, medium grade 15mm dia bore galvanized with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Refixing of old steel tubing obtaining from taking down and connections new or old position (wall, ceiling, floors etc.,) of 15mm bore complete all as specified and directed.

Taking up or down steel water tubing and connection 20mm dia complete all as specified and as directed.

S&F tubes, medium grade 20mm bore galvanized with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Refixing of old steel tubing obtaining from taking down and connections in new or old position (wall, ceiling floors etc.,) of 20mm bore complete all as specified and directed.

S&F 32mm bore low density polythylene pipes (LDPE) of pressure rating 6 Kgf/cm2 laid in trenches complete all as specified and directed.

S&F in repairs angle stop cock 15mm bore, fancy type, chromium plated (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or unions and fixed complete all as specified and directed.

S&F in repairs bib tap 15mm bore, fancy type, cast copper alloy, chromium plated, screwed down high pressure with crutch or butterfly screwed for iron and fixed complete all as specified and directed.

S&f in repairs pillar taps fancy type, cast copper alloy, with capstan head as chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and ply nuts screwed for iron pipes and fixed complete all as specified and directed.

S&F in repairs 32mm size waste couplings of PTMT (half or full threaded) minimum weight 32mm 45gms complete all as specified and directed.

S&F in repairs towel rail 450mm long of Stainless Steel fixed with and inlcuding chromium plated brass screws and wooden / plastic cleats (minimum weight 170gms) complete all as specified and directed.

S&f in repairs swivel shower of PTMT any coloured for fixing with 15mm pipe (minimum weight 40gms) complete all as specified and directed.

S&F in repairs shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour complete all as specified and directed.

S&F PVC connections 15mm size 600mm long with PTMT nuts complete all as specified and directed.

Demolition of precast cement concrete block waling as in manhole, septic tank and drains etc built in cement mortor all quoins, arches pillars etc but excluding ashiar facings sdresed stone etc all as specified and directed.

M &L for precast cement concrete block masonary with solid blocks, type C1 1:3:6 (20mm graded stone aggregate) exc 10cm in width and set in cement mortar 1:4 all as specified and as directed complete.

M & L for cleaning of blocked CI pipe line 100 mm bore, carefully in between manholes using splited bamboo, cleaning rod, binding wire etc and flush with fresh water and disposed off the sludge complete

M &L for cleaning of blocked CI pipe line 150mm bore, carefully in between manholes using splited bamboo cleaning rod, binding wire etc and flush with fresh water and disposed off the sludge complete.

(a) Water closet any description including trap and CI pipe line upto first manhole

(b) Floor trap/Nahani trap upto & including gully trap

(c) Pipe from gully trap upto first manhole (excluding gully trap)

Demolition of concrete of any description and in any position not other wise specifically provided for reinforced concrete complete all as specified and directed

Form work to sides of concrete foundations, footings, bases of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter.

Form work to sides of concrete foundations, footings, bases of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter.

M&L for mild steel TMT bars 10mm dia and over cut to length bent to shape required for fixing including cranking bending spirally for hooping ends and binding with and including mild steel wire (ammended) not less than 0.9mm dia.

- ditto - as above item but 6 to 8 mm dia and over upto and including 10mm dia in stirrups spacers and binders.

Dismantling of cast iron or reinforced concrete drain pipes jointed in CM and taking out of trenches /walls of 100 mm dia if required all as specified and directed

Dismantling of cast iron or reinforced concrete drain pipes jointed in CM and taking out of trenches /walls of 150 mm dia if required all as specified and directed

S & F for CI soil/Waste/vent pipes (sand cast) in any length with or without ears with cement joints, laid in trenches or in floor of 100mm dia complete all as specified and directed

S & F for CI soil/Waste/vent pipes (sand cast) in any length with or without ears with cement joints, laid in trenches or in floor of 150mm dia complete all as specified and directed

S & F for CI soil/Waste/vent pipes (sand cast) in any length with or without ears with cement joints, fixed with wall of 100 dia complete all as specified and directed.

Fixing only for CI soil/Waste/vent pipes (sand cast) in any length with or without ears with cement joints, , laid in trenches or in floor of 100 dia but except pipe complete all as specified and directed.

Fixing only for CI soil/Waste/vent pipes (sand cast) in any length with or without ears with cement joints, laid in trenches or in floor of 150 dia but except pipe complete all as specified and directed.

M &L concrete bed to drain pipes including packing under and completely surrounding pipes after they are laid and tested in cement concrete type C-2 1:3:6 (40mm graded stone) for 100 mm bore pipes complete all as specified and directed

M &L concrete bed to drain pipes including packing under and completely surrounding pipes after they are laid and tested in cement concrete type C-2 1:3:6 (40mm graded stone) for 150 mm bore pipes complete all as specified and directed

S & F CI cowls for bore of pipe 100mm

S & F for CI bends (any radius) diminishing or tappers of 100mm bore pie (larger bore measured)

Taking up or down old cast iron man hole cover and frame complete all as specified and directed.

S&F for cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing frames, manhole covers, fire and soot doors dampers, stop valve boxes, gate stops parts of ranges, balusters and similar articles n.exc.5 kg each complete all as specified and directed.

M &L providing cement concrete type C-1, 1:3:6 (20mm graded stone agg) as in coping benching, bed plate, including necessary form work complete

M & L for precast RCC type B-1, 1:2:4 (20mm graded stone aggregate) as in cover slabs, manholes covers and similar article including necessary form work complete set in CM 1:4 all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not hacking), removing serviceable tiles away site and rubbish off the premises complete all as specified and as directed.

M&L screed bed or bedding layer of mortar 15mm thick in cement plaster 1:4 for laying finishes as directed and specified.

S&F non skid coloured ceramic tiles 300mm x 300mm x 7 to 8mm thick in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for rendering 10mm thick cement plastered as backing coatr wall on fair surfaces of brick in cement mortar (1:3) to receive wall tiles complete all as specified and as directed.

S&F glazed ceramic tiles 300mm x 200mm x 6 to 7mm thick in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

S&F in repairs vitreous china wash basin white, flat back, size 550 x 400mm excluding taps, chain and plug and porcelain stopper but including brackets, waste couplings 32mm dia, cutting for and pinning in ends of brackets or errecting stand complete all as specified and directed.

S&F in repairs, vitreous china squatting pan, orissa pattern, size 580 x 440mm white, with integral foot rests (excluding flushing cistern and flush type) with and including connection to trap, set in and including concrete but connection to flushing pipe, anti syphonage pipe etc., complete inlcuding making good to floor, connection to drain (or out going pipe) etc., complete all as specified and as directed by Engineer-in-Charge (Make : Cera/Johnson/Parry Ware).

S&F in repair European type WC (Pedestal Pattern) complete inlcuding pedestal pan and trap inlcuding connection to drain, flushing pipe, seat cover (excluding fixing bolt, flushing cistern complete all as spefcified and directed.

S&F in repairs PVC valve less, syponic action type flushing cistern, 10 litres, low level, white with inlet ball valve, float and handle inlcuding brackets complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings exceeding 15 cm thickness above ground floors complete all as specified and directed.

M&L for hardcore of guage n exc 63mm, deposited, spread and levelled in layers n exc 15cm thick watered and rolled/rammed to a true surface all as specified and as directed.

M&L for 75 mm thick plain cement concrete 1:2:4, type B-2 (using 40mm graded stone aggregate) as in plinth protection.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. all as specified and as directed.

M&L for 50mm thick cement concrete 1:2:4 typeB-1 using 20mm graded aggregate as in flooring.

M&L for coloured chequered cement concrete tiles 30cm x 30cm x25mm thick, set in floors etc laid over and including 20mm thick screed bed in cement mortar (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match complete as specified and directed.

M&L for cement concrete 1:2:4 type B0 (using 12.5mm graded aggregate) as in flooring and rounded or chamfered on edges.

M&L for dividing strip 22mm width of strip plastic dividing strip 1.5mm thick all as per specified.

Taking down old unserviceable point wiring, (light, fan, socket or power) complete including fittings & fixtures such as switch, ceiling rose, pendants, regulator, socket, etc., and making good the disturbed surface of wall, floors, ceiling etc to match with the existing including touch up of paint/white wash all as specified and directed by Engineer- in-charge.

M & L for point wiring concealed/Surface on walls and ceiling complete with FRLS PVC insulated unsheathed 1100 Volts grade, conforming to IS-694, 1.5 sq mm (nominal area) multi stranded copper conductor cable drawn though in and including PVC conduit/ cassing capping heavy grade accessories, ISI marked, 19/20 mm dia including all accessories, concealed/Surface in walls by cutting chases using machine and making good the disturbed surface, with and including suitable boxes ,switch plates of suitable make and 1.5 sq mm copper earth continuity wire connected to earth dolly complete for the following complete all as specified and as directed. (a) One light point controlled by one switch.

(b) One fan/exhaust point controlled by one switch.

(c) One socket 5 Amps on independent board.

All as per item No. 98 on but with 4 Sqmm cable for 3 pin 15 Amps socket point controlled by one switch on independent board and 4 Sqmm copper conductor green in colour as earth continuity conductor complete all as specified and directed by Engineer-in-Charge.

M & L for point wiring concealed/Surface on walls and ceiling complete with FRLS PVC insulated unsheathed 1100 Volts grade, conforming to IS-694, 1.5 sq mm (nominal area) multi stranded copper conductor cable drawn though in and including stove enamelled steel conduit heavy grade accessories, ISI marked, 19/20 mm dia including all accessories, concealed/Surface in walls by cutting chases using machine and making good the disturbed surface, with and including suitable boxes ,switch plates of suitable make and 1.5 sq mm copper earth continuity wire connected to earth dolly complete for the following complete all as specified and as directed. (a) One light point controlled by one switch.

Supply & Fix Switch Flame Proof rotary type with termination box in LM6, 16A, single pole 250V.

Supply & Fix Switch piano, flush type single pole, one way 5 Amp

Supply & Fix switch socket combination outlet 2 in 1,3 pin 5 Amps flush type

Supply & Fix Switch Socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal

S & F stepped type electronic fan regulator flush type

Supply & Fix Ceiling rose Steel enamelled/ PVC insulated body with three terminals

Supply and fix surface mounting 18 W LED Tube light fitting nominal system lumen output of 2000 lumens and a minimum system efficacy of 100 lm/W. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70.The luminaire should have a color temperature of 6500K and CRI>83. pre wired connection up to tube light fitting with connecting up with copper 2 core flexible cord of minimum size 1.0 Sqmm and white in colour.The luminaire shall meet IP20 rating with THD < 10% and PF > 0.95. The total power consumption should not exceed 20W (including driver) including taking down old unserviceable fittings any type including round block complete all as specified and as directed.

Supply and fixing LED light fitting 1 x 60 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed by Engineer-in-Charge.

Supply & fix exhuast fans AC single phase 230 / 240 V of size 300 mm sweep with louver

Supply & fix fan ceiling complete with electronic type regulator and accessories 230 V, 1400 mm sweep

Supply & Fix LED Highbay Luminaire with AL Die Cast housing for efficient Thermal Heat management and secondary modular lens Optics for optimized Lighting distribution to improve operational efficiency, with EMC/ EMI Complient Potted Driver, Flicker free Illumination 55 W complete all as specified and directed

Material and labour for submain wiring with single core PVC insulated FRLS multistranded copper conductor cable of size 2 x 1.5 Sqmm drawing into and including rigid non metallic PVC conduit, medium grade not less than 20mm dia ISI marked ivory colour with all conduit fittings and fixing accessories and 1.0 Sqmm FRLS multistranded copper conductor cable as continuous earth wire incl taking out old wire completeas directed by Engr in Charge .

S & F in replacement sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including refixing / fixing of incomming & outgoing MCBs and making smooth the wall surfaces complete all as specified.

Supply only MCBs of following rating (a) MCB SP 6 to 32 Amps 240V 10 KA. "C" Series

(b) MCB SPN 32 Amps 240V 10 KA. "C" Series

M&L for earthing with galvanised steel earth plate electrode 60cmX60cmX6mm burried earth pit not less than 2.25m depth below normal ground level with to edge of the plate vertically to depth of not less than 1.5 m below ground level connected to & including Galvanised earth wire 4 sqmm by mean of GI bolts & nuts etc with provision of char-coal and salt etc all as per electrical plate No-3 of SSR-2010 including RCC cover and MS angle iron frame, watering with GI pipe 20 mm dia (medium grade) & MS funnel, concrete pit including excavation and earthwork and testing on completion etc. complete all as specified and directed by Engineer-in-charge. Note : 1. Refilling of the earth pit shall be carried out with black cotton soil. 2. GI wire 4.0mm dia & GI protection pipe upto 7.5 m length will be measured under this item.

M/s Gurunath Construction

A N KUMAR

M/s Karbhagam Sales Agency

M/s Kamal Electrical

USR Transport

DEEPAK AGENCIES

MAJUMDAR FURNITURE

A.G.Construction