SPECIAL REPAIR TO ROOF, FALSE CEILING, PLINTH PROTECTION, JOINERY AND SANITARY FITTINGS IN BLDG NO T 66, P 1 AND CERTAIN REVENUE WORKS IN AREA I UNDER GE SAUGOR

Amount

S&F pre- coated galvalume aluminum Zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa (AZ 150) as in roof covering/ clading to wall, including crimping sheet at end fixed with self tapping screws including dismantling of existing asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F pre- coated galvalume aluminum Zinc coating GI based steel sheet of 0.50 mm thick of any colour having tensile strength of 550 mpa (AZ 150) as in ridges of roof covering profile type and plain sheet as in valley gutter etc, fixed with self tapping screws including dismantling of existing asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section, in any position and removing to store complete all as specified and directed.

S&F mild steel rolled tubular sections as in main and cross beams, hip and jack rafters; purlins Posts where connected to common rafters and angle cleats or other connecting plates including wind ties Fe-410 Gde E-250 Quality A complete all as specified and directed

S&F mild steel framed work such as grills gratings, sunshed cover fixed with nut bolts incl,cutting drilling holes etc., with ends of bars shouldered and/ or riveted, similar work conforming to Fe 290 Gde E 165 complete all as specified and directed.

S&F mild steel work as in hand rails, half round or other steel section or core for wooden hand rail straight portion, drilled and counter sunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc flat iron fillets ( for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide or zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide 0r zinc chromate primer on new steel surfaces of any description not exc 10 cm width or girth including preparation of surfaces complete all as specified and directed.

M&L for brick work with sub class 'B' bricks old size, straright or corved on plan exc 6m mean radius built in cement mortar 1:6 including demolition of brick work and stone/ boulder masonary built in cement mortar and lime mortar complete all as specified and directed.

All as per Srl item No.09 above but except bricks -ditto- Note:- Old bricks obtained from demolition shall be re-used in this item.

M&L for brick work with sub class 'B' bricks, straright or curved on plan to any radius as in half brick thick walls built in CM 1:6 complete all as specified and directed.

Taking down cement plaster on brick wall etc including racking out joints hacking for key, scrubbing down with water as described complete all as specified and directed.

M&L for rendering 15mm thick on brick wall or concrete surface in cement mortar 1:6 finished fair and even complete all as specified.

M&L for rendering 15mm thick on brick wall or concrete surface consisting two layers, under layer of 10mm thick in CM (1:6) & top layer of 5mm thick in cement mortar 1:4 mixed with water proofing compound, finished even and smooth without using extra cement complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid separately.)

Supply only liquid water proofing compound complete all as specified and directed

M&L for applying two coats of exterior emulsion weather proof paint over one coat of exterior wall primer on newly plastered or unplastered wall surface including preparation of surfaces, complete all as specified and directed. Make:- Asian Apex or equivalent make as approved by GE

M&L for preparation of new plastered surface of wall and applying two coat of distemper oil emulsion white or tinted over a layer of 2mm thick JK/Birla wall care putty complete all as specified and as directed.

M&L for applying two coat of interior oil emulsion white or tinted over a layer of 2mm thick wall care putty on old decorated wall surface including complete removal of old decorated surfaces of walls by washing rubbing down and stoping of distempered and painted surfaces complete all as specified & directed.

M&L for two coat of synthetic enamel paint on old painted wood/wood based surface of any desription over 10cm width or girth incl preparation surfaces such as removing all splashes, drops, dirt, rubbing and leaving premises in a clean state complete all as specified and directed

Demolition of cement concrete not exc 15 cm thick below or above ground level as in floor Paving etc including removal of demolished material from work site complete all as specified and directed

M&L for 75 mm thick PCC 1:3:6, type C-1 (using 20mm graded stone aggregates) as in plinth protection finishing cement concrete surfaces even & smooth without using extra cement including forming construction joint of size 10mm x 20mm filled with bitumen sand mortor (1:3) complete all as specified and directed..

M&L for PCC 1:4:8, type D-2 (using 40mm graded stone aggregates) as in foundation filling, sub base, level course and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4, type B0 ( using 12.5mm graded stone aggregates ) as in coping , apex stone , bed plate , kerbs including weathering , slightly rounded or chamferred angles and throating and including necessary form work complete all as specified and directed.

Taking down chowkat with shutter n.exc 1.5 sqm each (without taking off shutters from the frame) and removing from site complete all as specified and directed

Taking down chowkat with shutter exc 1.5 sq.m but n.exc 4 Sqm each and removing from site complete all as specified and directed

S&F second class hard wood plain, solid, straight, chowkat and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F mild steel bands, straps, clamps, holdfast, hooks, plain angle cleats for securing purlins, and similar small articles conforming to Fe 290 Gde E 165 complete all as specified and directed

M&F for PCC 1:3:6, type C-1 (using 20mm graded stone aggregates) as in bed blocks for hold fast, kerbs etc complete all as specified and directed.

M&L for preparing surface of wood and wood based material and steel and iron work of any description and girth and treating ends of post, back of chowkats etc, area exc. 0.1 Sqm but not exc. 0.5 Sqm, with tar or coal tar or black paint complete all as specified and directed.

M&L for preparing surface of wood and wood based material and steel and iron work of any description and girth and treating small articles such as stop, covers, gully gratings, holdfasts, etc., area not exc 0.1 Sqm each complete all as specified and directed.

S&F 30 mm thick flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both side, including fixing of prelaminated sunmica on both sides of plywood complete all as specified & directed.

S&F 35mm thick second class hardwood factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc divided into panels with plain or mitered shash bars any numbers of panels, edges of framing plain, chemfered or rounded, fitted with cut and mitred beads for securing glass, etc,sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20 (a) complete all as specified and directed

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F solid PVC frame (single rebated) of size 50mmx47mm made out of 5mm prelam PVC sheet used instead of plain colour PVC sheet and edges will be painted to match with prelam sheet and reinforced with mild steel square tube complete all as specified and directed

S&F factory made soild PVC moulded door shutter, 28mm to 30 mm thick (stiles) with wood free EPS with 2, 4 or 6 raised panel design with 4mm thick moulded prelam PVC sheet on the front face & 4mm thick plain colour sheet on back face complete all as specified and directed

S&F winpire 3 track pre painted steel sliding window 3-track, 2glass panel and 1 mesh panel ,sliding window fabricated from roll formed section made of galvanized steel colour coated/powder coated (base steel as per IS 513 D quality galvanized as per IS 277 with Zinc of 120gm/sqm ) with total coated thickness of 0.58mm primer coat with epoxy primer of 5-7 micron thick ,finish painted with a polyester paint of 12-16 micron thick and back coated with alkyd backer of 5-7 micron or powder coated with pure polyester up to 50-60 micron thick. section for external frame should be off 107X44 mm, section of shutter should be of 35 x 49 mm. section of mesh should be 35 x 49 mm . the window should be paneled with 5mm thick plain flot glass and stainless steel wire cloth with 0.36mm nominal dia of wire and average width of aperture 1.18mm. Corner bracket for internal and external frame made of glass filled nylon. Gaskets are to be made of Ethyl Propylene Diamine Monomer (EPDM) . The sections are to be cut to length, join and assembled by mean of corner bracket . The above frames should be fixed to the concrete/ masonary wall by means of self expanding screws complete all as specified and directed (Make: NCL ALLTEK & SECCOLOR LTD or equivalent make as approved by GE)

S&F galvanised mild steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanesed wire stapels complete all as specifed and directed.

S&F 200mm long aluminium barrel tower bolt,of extruded section, with bright bolt and fixed with screw complete all as specifed and as directed

S&F 125mm long aluminium barrel tower bolt,of extruded section, with bright bolt and fixed with screw complete all as specifed and as directed

S&F Alluminium alloy anodised,sliding door bolt with hasp and staple(bolt type) and fixing clips of sheet,cast ortruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed 300mm long fixed with screw complete all as specifed and as directed

S&F 125 mm size MS butt hinges medium weight cold rolled fixed/ welded to frame complete all as specified and directed

S&F 150mm size aluminium handles,cast type,anodised fixed with screw complete all as specifed and as directed

S&F mild steel bands,straps, supports or stays for rainwater pipes, soil/waste or vent pipes including bolts, if required, hold fast and similar small articles conforming to Fe 290 Gde E-165 complete all as specified and directed

Dismantling of floor, hearth or wall tiles / terrazo including cement mortar bedding, removal servicable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for PCC 1:2:4, type B-1 (using 12.5mm graded stone aggregate) 25mm thick as in floor finishes complete all as specified and directed..

M&L for non-skid coloured ceremic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specfied and directed.

All as per Srl item No. 46 above but in skirting, dado, etc., laid over and including 10mm thick rendering in CM (1:4) -ditto-

M&L for glazed ceremic tiles of size 600mmx300mmx7mm thick in vertical surfaces such as skirting, dado, etc., set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10 mm thick rendering in CM (1:4) complete all as specfied and directed.

M&L for non-skid coloured ceremic tiles 7 to 8 mm thick (Square/ rectangular ) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm as in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specfied and directed.

M&L for machine pressed precast cement concrete coloured chemically treated interlocking paver block any shape and size conforming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment laid over and including 40mm thick uniformly levelled surface of stone dust cushioning complete all as specified and directed.

M&L for 20mm thick granite slab (table rubbed and polished ), machine cut, for floors/ shelves, cooking platforms, window cills etc laid over and including 15mm thck CM 1:4 cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing edges to be rounded including dismantling of old exisitng stone or flooring of any description & removing from site complete all as specified and directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing including taking up or down steel tubing and connections complete all as specfied and directed..

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing including taking up or down steel tubing and connections complete all as specfied and directed..

S&F in repairs 15 mm dia bib tap cast copper alloy (fancy type), chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and directed

S&F in repairs vitreous China WHB white flat back size 550x400mm including fixing of ms brackets, cp pillar tap fency type 01 No 15mm bore, CP waste coupling 32mm dia and PVC waste pipe 32mm dia and PVC connection 450mm long high pressure complete all as specified & directed.

S&F in repairs stop valve 15mm bore, cast copper alloy, fancy type,chromium plated with long shank and cup (Concealed type), screwed down both ends for high pressure complete all as specified and directed

S&F in repairs gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20mm bore complete all as specified and directed

S&F 1000 ltr capacity of rotational moulded polyethyline water storage tank (Cylindrical vertical with closed top) three layered wall construction hoisted & fixed in position incl S&F 20mm dia GI Pipe medium grade washout pipe 450mm long with plug & 20mm dia GI pipe medium grade overflow pipe 600 mm long with fittings complete all as specified & as directed including dismantling of water tanks complete all as specified and directed.

S&F in repairs vitreous China squatting pan 'Orrisa pattern' size 580mmx440mm white with integral foot rests any pattern including provn of cement concrete bedding and making connection with & including P or S trap complete all as specified and directed.

S&F in repairs vitreous China wash down water closet pan (pedestal pattern), coloured, with and including plastic water closet seat cover, coloured, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device, including cp jet spray, fixing bolts and connection to drain (or outgoing pipe) and to flushing pipe, anti -syphonage pipe, etc., complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 Ltr capacity including flushing pipe bend PVC bend complete all as specified and directed.

S&F in repairs vitreous China urinal half stall type off white with grating and union for discharge pipe, CP sprayer, waste pipe, complete all as specified and directed.

S&F in repairs 110mm dia PVC(SWR) pipes single soketed in any length with adhesive joint fixed to wall including mild steel clamps complete all as specified and directed

S&F in repairs 110mm dia PVC(SWR) pipes single soketed in any length with adhesive joint fixed to floor or trenches including fittings complete all as specified and directed

S&F in repairs PVC (SWR) 110 mm dia junction, single(single 'T') equal or unequal complete all as specified and directed .

S&F in repairs 110mm PVC(SWR) bends any radius with acess door complete all as specified and directed.

S&F in repairs PVC (SWR) pipes 75mm bore single socketed, in any length with solvent joints laid in trenches or in floors with fittings complete all as specified and directed.

S&F in repairs 75mm PVC(SWR) bends any radius with acess door complete all as specified and directed.

S&F in repairs for 75 mm dia PVC ( SWR) floor trap with grating including jointing with solvant etc complete all as specified and directed.

S&F in repairs 110mm PVC(SWR) vent cowl complete all as specified and directed.

S&F in repairs 25 mm bore PVC coated MS conduit rods, suitable for door/widows curtain with fancy type dooms fitted to each end and brackets fixed to wall incl. removal of existing rod and making good etc complete all as specified and directed.

M&L for 600x600x9mm thick vinyl face, cinyl covered edges and washable metallized polyster foil backing, weight @ 5.6Kg/m2 suspended false ceilling comprising of non asbestos fibre cement bulding boards fixed or laid/inserted to GI frame work with screws over GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to sourrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fastners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm center to centre including hangers 6mmm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long including dismantling false ceiling any description or in any thickness with cover fillets complete all as specified and directed. Make : ArmGyp-FB Ceilings (Armstrong) Model : Sleet (Alpha Lite) or equivalent make as approved by GE

M&L for true horizontal level 600 mm X 600 mm false ceiling system using hot dipped galvanized steel section, exposed surface with pre-coated capping, main tee of size 24 x 32 mm., having 0.27 mm gauge (thickness) at every 1200 mm. centre to centre maximum and rotary stitched cross tee of 24 x 32 mm, having 0.27 mm gauge (thickness) at every 600 mm. c/c. and sub cross tee of size 24 x 32 mm, having 0.25 mm gauge (thickness) at 1200 mm c/c. and wall angle of size 19 x 19 mm., having 0.35 mm gauge (thickness) fixed to the periphery of the wall. The above grid is suspended at every 1200mm c/c. in both directions using 2.0 mm. thick pre-straightened GI wire laying laying Dune Tegular Edge ceiling tiles manufactured by M/s. Armstrong World Industries,or equivalent of size 600mmx600mmx16mm having NRC 0.50, Light reflectance of >85% (WT), thermal conductivity k = 0.052-0.057 W/m0K, Humidity Resistance of 99% (having lifetime guarantee against SAG), having Fire Performance Class O / Class 1 (BS 476), surface having 3 coats of white paint - crisp finely granulated with microperforations, back of the tile duly sanded and finished with a coat of protective paint over the formed grid complete all as per manufacture instruction including dismantling false ceiling any description or in any thickness with cover fillets complete all as specified and directed. Make:-M/s. Armstrong World Industries or equivalent make as approved by GE

M&L for gypsum boards in suspended system ceiling as in flat or vertical step up or down pattern (GS-MFSC-4.1) including GI perimeter channel of size 0.55 mm thick (having one flange of 20 mm and another flange of 30 mm and a web of 27 mm ) along with perimeter of ceiling, screw fixed to brick wall with partition with the help of nylon sleeves and screws at 610 mm centre to centre. Then suspending GI intermediate channel of size 45 mm (0.9 mm thick with two flanges of 15 mm each) from the soffits ot 1220 mm centres with ceiling angle of width 25 mm x 10 mm x 0.55 mm fixed to soffits with GI cleat and steel expansion fasteners. Ceiling section of 0.5 mm thickness having knurled web of 51.5 mm and two flanges of 26 mm each with lips of 10. 5 mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457 mm centres to centres, 12.5 mm tapered edge gypsum boards (conforming to IS 2095 –1982) is then screw fixed to ceiling section with 25 mm dry wall screws at 230 mm centres to centres.Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. The board are to be jointed and finished the tapered and square edges of the board with jointing compound, joint paper tape and applying two coats synthetic distemper over a coat of primer suitable for Gypsum board complete all as specified and directed.

S&F cupboard panels, shelf, shutters of 19mm thick prelaminated MDF board, waterproof and termite proof interior grade, prelaminated both side with decorative choice lamination with 5mm thick teak wood edging on front side, bottom and top and other side 10mm teak wood edging with rebate and leaping treated with french polish complete all as specified and as directed. Make : Texa, Archidply, Greenply

S&F second class hardwood plain fillets square, rectangular in section clean sawn, secured with nails or beads area exc. 13 Sqcm but not exc. 25 Sqcm complete all as specified and directed

S&F continuous piano hinges mild steel bright finish or electro galvanized with open flap width 30 mm complete all as specified and directed

S&F ball catches magnet type , with striking plate including complete all as specified and directed.

S&F 125 mm size steel handles, fancy type,anodised complete all as specified and directed

S&F aluminium partition consisting of frame 101.6 mm x 44.45 mm fixed with 8 mm thick preliminated board at bottom and 4mm thick tinted glass on top covered with aluminium frame and secured with aluminium beading , including necessary cutting holes on wall and floor and confirming to IS complete all as specified and directed (Note:- Aluminium section thickness 1.50 mm }

Taking down copper/aluminium point wiring (light fan, socket or power) complete including fittings such as switch, sockets, c/rose, lamp holders, tube light fittings, sketch fitting , wooden boards, bell push, call bell, MCBs & regulators etc & making good to disturbed surfaces & matching with the existing colour of wall floor complete all as specified and directed

Taking down main switch, DB ,Metal box of any capacity complete all as specified and directed.

M&L for concealed point wiring for the following with 1.5 Sqmm PVC-FR insulated, unsheathed, copper conductor, stranded 1100 volt grade cable in & incl PVC conduit, including modular metal flush boxes & modular white cover plate with frame as per site requirement all fittings such as tees, bends, elbows, etc. of External diameter 20mm all as per site requirements PVC insulated & unsheathed 1100 volt grade copper conductor, stranded 1.5 sqmm. cable as continuous earth lead complete all as specified and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as specified and directed. Make– HAVELLS/FINOLEX/Polycab

For one light/fan point controlled by one switch

For one Call Bell point controlled by one push button .

For one 3 pin, 5 Amp independent socket point controlled by one switch

For one 3 pin, 5 Amp socket point with other switch on the same board

All as per Srl item No 84 here in before but for power point wiring using with 2.5 sqmm PVC-FR insulated ,unsheathed, copper conductor stranded 1100 volt grade cable and 2.5 sqmm PVC insulated ,unsheathed, copper conductor stranded 1100 volt grade cable as continuous earth lead complete all as specified and colour coding of cables such as Phase-Red, Neutral-Black and Earth-Green.

S&F modular switch, one way,6 Amp 230, 1 module complete all as specified and directed. Make:- Havells Reo series/ L&T/Schneider.

S&F modular socket 6 Amp-2/3 pin combined 2 module complete all as specified and directed Make:- Havells Reo series/ L&T/Schneider.

S&F modular switch, one way,6 A/16 Amp 230, 1 module complete all as specified and directed. Make:-Havells Reo series/ L&T/Schneider.

S&F modular socket 6 A/16-2/3 pin combined 2 module complete all as specified and directed. Make:-Havells Reo series/ L&T/Schneider.

S&F modular bell push 6A one module complete all as specified and directed. Make:- Havells Reo series/ L&T/Schneider.

S&F ceiling rose, surface backlite, three terminal complete all as specified and directed. Make:-Havells Reo series/L&T/Schneider.

S&F lamp holder modular type insulated with back plate suitable for Angle/Batten fitting with 9 Watt LED bulb. Make Havells Reo series/ Cona/Leader.

S&F modular fan step regulator 120 Watt -2 module complete all as specified and directed. Make:- Havells Reo series/ L&T/Schneider.

Taking down and refixing connecting of Ceiling fan,Exhaust fan after greasing complete all as specified and directed

S & F in repair/replacement bell ding dong 230 V, single phase complete all as specified and directed. Make- Havells Reo series/ L&T/Schneider.

S&F TL fitting 20 /18 watt for surface and wall mounted LED batten with ultra slim polycarbonate LED lighting fixture with high lumen output environmental friendly energy efficient complete all as specified and directed. Make:- Havells Cat Part No LHEXBLP7PN1W020, 4 feet/ Bajaj cat part No BCLSB 20 WH/ CG Cat part No LCTC-18-CDL

S&F box type LED optic fitting 1x9 Watt 2 feet box type complete all as specified and directed. Make:- Havells Cat Part No LHEXBLP7IN1W009/Bajaj cat part No BCLSB10WH/ CG Cat part No LCTL-9-CDL.

S&F exhaust fans AC single phase 230/ 240 V of size 250 mm sweep PVC body with lovers complete all as specified and directed. Make -Havells cat part No Ventil Air -DX White/Bajaj MAXIMA DX/Crompton Ventilus10ʺ

S&F in replacement of 2 X 2 ultra slip recess mounted luminaire with high brightness 36 Watt LED package and Unique pattern acrylic de-glaring diffuser sheet for glare-free uniform light distribution suitable for armstrong/grid ceiling complete all as specified and directed. Make-Havells cat part No PLANO2X2PLR36WLED857S/CG cat part No.LCPL-36-CDL(2X2)/Bajaj cat part No.BPSF 36W WH LED

S&F LED FLEXION STRIP 22 W ,3000k flexible LED strip With including LED driver, with wide viewing angle for good light distribution, easy to install complete all as specified and directed. Make-Havells Cat part No. LHEHCPP5IN1W018 or eqivalent Bajaj/ Wipro

S&F testing and commissioning of MCB SP 240 volt 6 Amp to 32 Amp 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed. (Make:- Legrand/ L&T/Havells.

S&F testing and commissioning of MCB SPN 240 volt 16 Amp to 32 Amp 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed.. Make:- Legrand/ L&T/Havells.

S&F testing and commissioning of MCB SPN 240 volt 32 Amp to 63 Amp 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed.. Make:- Legrand/ L&T/Havells.

S&F sheet metal enclosure for DB double door, IP-43 when MCBs to be used SPN, 8 way, 240 V with 200 Amps rated bus bar of suitable size complete all as specified and directed. Make- Legrand/ L&T/Havells

M&L concealed sub main wiring with two single core PVC insulated unsheathed stranded copper conductor cable FR 02 runs of 01 Single core of size 6 sqmm (for main current) drawn in & incl PVC conduit Heavy duty not less than 20mm dia ISI marked with all accessories such as tee, bend, joint cover etc round / square blocks at junctions etc, all as per site requirements ISI marked with one run of 01 Single core of size 6 Sqmm (As earth wire) PVC insulated unsheathed stranded copper conductor as a continuous earth wire complete all as specified incl. taking down old unserviceable sub main wiring and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as specified and directed. .Make of cable:-Havells/Polycab/Finolex

M&L for concealed sub main wiring with 2 single core PVC insulated, unsheathed copper conductor stranded 1100 volt grade cable of size 4 sqmm (FR) drawn in and incl PVC rigid conduit medium grade of size not less than 20 mm dia ISI marked ivory white with all accessories such as tee, bend, joint cover etc PVC insulated, unsheathed copper conductor stranded 1100 volt grade cable of size 4 sqmm cable as continuous earth lead complete all as specified and colour coding of cables such as Phase-Red, Neutral-Black and Earth-Green complete all as specified and directed. Make of cable:– Havells/Polycab/Finolex .

S&F metal clad box enclosure with socket plug top and MCB SP 20 Amps flush mounting enclosure with 2 pin and earth plug socket complete all as specified and directed. Make:- Legrand/ L&T/Havells

S&F PVC conduit of size 20mm dia including fixing on wall/ceiling with suitable clamp/saddles for wiring wire all as required at site complete all as specified and directed.

Supplying and laying cable XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade cross sectional area 10 sqmm 2 core complete all as specified and directed. Make - Polycab/Plaza/Havells

M&L for provn of earthing complete with MS galvanized earth plate electrode 600x600x6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below normal GL) with top edge of plate not less than 1.5 M below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of CI or steel incl excavation, PCC (1:3:6) type C-1 chamber with CI cover 10 mm thick, 15 mm dia light grade , GI protection pipe, funnel with wire mesh, watering pipe of size 20 mm dia, medium grade, lugs, main earthing lead upto main switch/DB incl charcoal dust, salt etc all as shown in electrical plate No. 3 of SSR part-I 2009 specification.

A Raza Enterprises

maharaja construction and suppliers

PARAS BROTHERS

SAGAR MOTOR AND TRACTOR CO

SHIV SHANKAR MISHRA