SPECIAL REPAIRS TO OTM VINTAGE BLDG NO E-35 and E-35A OF 1 EME CENTRE UNDER GE (NORTH) SECUNDERABAD.

Amount

Dismantling mangalore pattern roofing tiles single layer including ridge tiles laid, bedded in cement mortar etc complete all as specified and as directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coveringsetc complete all as specified and as directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

Dismantling battens for tiles any size exceeding 15cm in spacing complete all as specified and as directed.

Dismantling timber Scantling framed work 40 sqcm and over in section, in any position complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) of size not exceeding 1.5 Sqms each complete all as specified and as directed

Taking down chowkats or frames with shutters (without taking off shutters from frames) of size exceeding 1.5 sqm and not exc 4.00 sqm each complete all as specified and as directed

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete incl removal of demolished material to a distance as specified.

Demolition of cement concrete of any description and in any position not otherwise specifically provided in roof padding concrete etc complete incl removal of demolished material to a distance as specified.

Taking down of old bituminous tarfelt or any other type of roof treatment from roof/ concrete surfaces removal to distance exceeding 250 metres and not exceeding 500 metres from the site and cleaning of the roof surface with wire brush to make it free from dust, dirt etc complete all as specified and as directed.

Taking down cement plaster of any description and thickness on brick walls including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed

Demolition of brickwork or stone/boulder masonry, built in cement mortar with all quoins, arches, pillars, etc but excluding ashlar facings, dressed stone work and precast concrete articles including disposal of the rubbish out off the premises complete all as specified and as directed.

S&F joist channel, angle or tee sections, fixed independently without connecting plates, etc., (cut to ordinary lenghts i.e within 20mm of the length indicated of Fe 410-W ( Gde-E-250) quality A

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk forming holes, without any attachment etc. Roof strusses (framed) and connecting plates, etc., including necessary precautionary measures as in supports etc., as directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing boltsand similar work conforming to Fe 290 Gde E-165 etc complete all as specified and directed.

S&F Mild steel bolts.purpose made.with hexagonal or forming holes, without anyattachment dia of neck exc 16mm not exc 20mm

Supply and fix pre-painted galvalume aluminium zinc coating galvanised based corrugated steel sheet of 0.50 mm thick of approved colour having tensile strength of 550 Mpa as roof covering/cladding to wall fixed with self tapping (SD) screws complete all as specified and as directed.

Supply and fix pre-painted galvalume aluminium zinc coating galvanised based plain steel sheet of 0.50 mm thick of approved colour having tensile strength of 550 Mpa as ridge, gutters fixed with self tapping (SD) screws complete all as specified and as directed.

M&L for preparation of new surfaces of steel, of any description, not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of old surfaces of steel, of any description, not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Demolition of RCC as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and and as directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including (annealed) not less than 0.9mm dia or securing with clips and complete alla s specified.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick .

RCC Type B1 1:2:4 (20 mm graded aggregate) (Nominal mix) as in Chajjas complete all as specified and and as directed.

Material and labour for brick work with sub class 'B' bricks of old size, straight or curved on plan exceeding 6.0 metre mean radius built in cement mortar 1:6 complete all as specified and as directed.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with clips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre over the grid providing 4mm thick HPSC pre primed self designer texture non asbestos fibre cement building board fixed to frames etc, including taking down old ceiling of any description, complete all as specified and and as directed.

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and as directed

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces in two coats (10 + 5 mm), both coat mixed with integral water proofing compound ISI Marked @ 2% by the weight of cement and finishing the surface even and fair complete all as specified and directed Note - WPC shall be measured and paid separately.

Supply only water proofing compound of ISI marked complete all as specified and as directed.

M & L for preparing newly plasterd wall surfaces of ceillings and applying three coats of white wash on ceillings complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded aggregate) in copings, kerbs, channels, water through and the like including weathering, slightly rounded or chamfered angles and throating as directed chamfered necessary for work.

M&L for 75 mm thick plain cement concrete 1:4:8 mix,type D2 (using 40 mm graded stone aggregates) as in subbase to floor complete all as specified and as directed.

M&L 25 mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) as floors, sub-floors etc and finishing surfaces of concrete topping as even & fair or even & rough to receive the topping layer all as specifed.

Material and labour for Non skid coloured ceramic tiles of size exceeding 0.18 square metre but not exceeding 0.38 square metre of 7 to 8mm thick set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including cement screed bed of cement mortar 1:6 of 15 mm thick complete all as specified and as directed.

Material and labour for glazed ceramic coloured wall tiles of approved colour of size 350x 250x 7/ 450x300x7 mm thick on vertical surfaces as in dado/wall set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and as directed.

M&L 20-25 mm thick machine cut Polished kota stone as inflooring laying down and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over bedding layer of 15mm thick in CM 1:6 complete all as specified and directed.

M&L 20-25 mm thick machine cut Polished kota stone as in skirting / riser of staircase laying down and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over backing coat of 10mm thick in CM 1:4 complete all as specified and as directed.

Material and labour for 25 mm thick granite tiles (of any size) machine cut, jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone duly grinding and polishing laid over and including 15mm thick screed bed of 1:4 in steps, jambs, pillars, window cills, cooking platforms and like complete all as specified and as directed.

Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified.

S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm incl waste coupling and waste pipe etc., and complete all as specified and directed.

Providing precast ce- ment concrete Type B1 1:2:4 (20 mm graded aggregate) (Nominal mix) as in chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain facecomplete all as specified and and as directed

M&L for designer rubber moulded chequered cement concrete tiles with mixture of grey pigment cement and pigment in equal porportions with pigments of size 200x 200xx25mm ,300 x 300 x 22mm or 250 x 250 x 22mm thick and set and pointed in neat cement slurry in floors over a screed bed or bedding layier in CM 1:6, 15mm thick for laying floor finishes etc complete all as specified and as directed.

Cement concrete in foundations, filling and mass concrete Type E2 1:5:10 (40mm gradedaggregate) as in sunken floor fillins.

Supply and fix steel windows (fly proof and glazed shutter) made with galvanised steel colour coated/ powder coated ( Base steel as per IS 513 'D', galvanised as per IS 277 with zinc of 120gm/sqm) with total coating thickness of 0.60mm. ( outside for glazing and inside gauged shutter) Sections for frame should be of 72mmx55mm, section for mullian should be 72mm x 50mm section for shutter frame should be 47mmx 20mm,and section for fixing glass bead should be 12mm x 12mm and section for fly mesh shutter frame should be 40mm x 20mm mesh fixing should be of 18mm x 0.6mm. Stainless steel wire mesh of 0.45mm dia and ave width of aperture 1.4mm shall be used for fly proofing . 4mm thick plain sheet glass to be used for glazing of glazed shutters including 10mm powder coated square saftey grills, locking arrangement and all necessery accessories etc, completed all as specified and directed.

S&F 125 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed.

S&F 105 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed.

Material and labour for plain cement concrete 1:2:4, type B0 (using 12.50 mm graded stone aggregate) as in coping, bed plates, filling back hollow portion of chowkats complete all as specified and as directed

S & F 40 mm thick factory made second class hardwood, plain framed panelled shutters (any number of panel) with panels of timber flat on both sides(feather edged) or of veneered particle board medium density wood particle board with commercial veneering on both faces. complete all as directed and specified.

S & F 35 mm 2nd class hard wood factory made glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Part-I section 8 clause 8.24(a) etc completed all as specified and directed.

S & F PVC solid ventilator frame size 55 X 47mm with wall thickness of 5mm made out of extruded 5mm PVC sheet, mitre cut at two comers and jointed with 2 Nos of 150mm long brackets of 15 x 15mm MS square tube the two vatted profiles are to be reinforced with 19 x 19mm MS squre tube the 50% of bottom portion is fixed with 4mm pin headed glass and balance 50% of top portion is fixed with 4mm thick pin headed glass lowers and cover with 0.36mm dia stainless steel wire mesh at top portion including necessary PVC beading with screws and 3 Nos 12mm dia MS guard, bars fixed in ventilator frame including two coats of synthetic enamel paint over a coat of red oxide primer to MS guard bars etc all as per specified and directed (Make SINTEX or epuivalent seetings in RAJSHRI , NANDI make as approved by accepting officer) complete all as specified and as directed

Supply and fix Factory made single extruded WPC (Wood Polymer Composite) solid door Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantcomplete all as specified and as directed

S & F 30mm Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) complete all as directed and specified.

Supply and fix butt hinges of 100mm size stainless steel with stainless steel hinge pin, complete all as specified and as directed

Cutting holes in brick wall exc. half brick but not exc. one brick built in cement mortor for inserting hold fast and making good the disturbed portion in cement mortor 1:3 depth of embeded portion exc half brick & N.exc one brick.

S&F of Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

M&L for Providing, cement concrete Type C1 1:3:6 (20mm graded aggregate) in steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

M & L applying new wood surface two coats of synthetic enamel paint over a coat of prink primer on wood or wood based material over 10 cm width or girth including preparation of new wood surface

M & L preparation of old painted surfaces of wood and applying Two coats of synthetic enamel paint on wood or wood based material over 10 cm width or girth.

S&F for Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc all as specified and directed.

S&F 150 mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 300 Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

Removing excavated material (soils) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

M&L Hard core of broken stone or boulders of gauge not exceeding 63mm deposited, spread and levelled in layers not exceeding 15cm thick, watered and rolling with power roller exc. 8 tonne & n.exc. 12 tonne to a true surface complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) in plinth protection laid in alternative bays finished even and smooth without using extra cement including making 10 mm wide grooves to full depth at 3 m interval and at every change of direction and filling the grooves with mixture of bitumen and sand mixed in the ratio of 1:3 by weight and top 10 mm depth sealed with sealing compound grade ‘A’ complete all as complete all as specified and as directed.

S&F of 25 mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed and complete all as specified.

M&L for PCC 1:2:4 Type B0 using 12.5 mm graded aggregate with 2% by weight of cement or as per manufacturer's instructions water proofing as in levelling course, haunching, coping and similar works over RCC roof surface and RCC over head tank top surface including rounded or chamferred on edges and formwork etc all as specified and directed. Note: Water proofing compound will be measured and paid separately under relevant item in this schedule.

Material and labour for rendering 10mm thick on roof surfaces in cement mortar 1:3 duly mixing with water proofing compound at the rate of 3% by weight of cement and finished even and smooth complete all as specified and as directed Note: Water proofing compound will be measured and paid separately under relevant item in this schedule.

M & L for providing water proofing treatement with APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick reinforced with polyester non oven fabric ( weight not less than 150gm/Sqm) applyied on one coat of oil based bitumen emulision primer @ 0.3 lit per sqm ( OR as per the directions of manufacturer instructions) including cleaning of surface thoroughly from dust, dirt and projections. Laying of membrane by forced ( torch) application with 10cm overlaps . A coat of blown bitumen 85/25 grade @ 1.2 Kg/sqm to be applied on top of memberane, finally coating the surface with bituminous aluminium paint @ 100gm/Sqm complete all as specified.

M&L for making the grooves to 'V' section in existing parapet walls/columns over RCC roofs, cleaning out and tacked the polymeric membrane in to the grooves and sealed solidly with a hot mixture of bitumen and clean dry sand in the ratio of 1:1 by weight etc complete all as specified and directed.

S&F PVC (SWR) Nahani /Floor trap, 75 mm dia of out let, plain with grating including jointing to waste pipe with solvent and cement concrete type B1 (1:2:4), including CP grating and removing old trap and fixing of stainless steel grating in ground shape etc complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps 8mm dia with two nuts wall nails etc, including removing old pipe of any description and complete all as specifed and directed.

S&F 110 mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , laid in floors etc, including removing old pipe of any description complete all as specifed and directed.

S&F 110mm bore PVC (SWR) bends any radius dimnishing pieces or tapers with access doors etc, including removing old bend of any descriptioncomplete all as specified and as directed.

S&F 110 mm bore PVC (SWR) junction single (single T ) equal or unequal with access doors etc, including removing old junction of any description complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) vent cowl etc,including removing old cowl of any descriptioncomplete all as specified and as directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 15 mm complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20 mm complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 25 mm to 32 mm complete all as specified and directed.

S&F Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. SDR 11, 20 mm outer dia of pressure rating 6kgf/sqcm conforming to IS-15778 with all CPVC fittings with such as brass elbow ,Tee, bends, unions ,sockets , male and femaleThreaded Adoptor and end pieces etc to receive fittings and fixed with solvents fixed to walls / ceiling with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure etc complete all as specified and as directed.

All asper item No 84 above but 32 mm

Cutting and grooving of wall for fixing of CPVC pipe lines and after fixing of CPVC pipe line and making good of all cutting surfaces etc complete all as specified and directed.

S&F in repairs vitreous china water closet 'Orissa' pattern of size 580mm X 440mm, white with integral foot rest (excluding flushing cistern), but including PVC flush pipe and provision of lime concrete bedding complete all as specified and as directed.

S&Fin repair wash down water closet (pedestal pattern) white and including plastic water closet seat cover as per reqd colour with flat bottom and cover and mild steel chromium plated or aluminium hinging device (excluding flushing cistern ) etc complete all as specified and directed..

S&F in Low level flushing cistern 10 ltr capacity, PVC incl waste pipe, down take pipe, pair of CI brackets and all accessories complete all as specified and as directed.

Supply and fixed in repairs 2000 litres capacity rotational moulded polyethylene water storage tank of triple layer type(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed

S&F in repairs vitreous China counter top wash basin of size 600 x 450 x 190 mm with 32mm dia brass chromium plated waste coupling, waste pipe and cast iron brackets complete all as specified and as directed. MAKE: CAT No Jaquar Code- QNS-WHT-7601AT No 10051 or equivalent in HINDWARE PARRYWARE/CERA as approved

S&F in repairs Pillar taps, fancy type, chromium plated, screwed down, high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed 15 mm bore complete all as specified and as directed.

Supply and fix in repairs 125 mm dia brass chromium plated shower rose with swivel joints with stainless steel arm duly ISI marked complete all as specified and as directed

Supply and fix in repairs of PVC connection of 15mm size with PTMT nuts of length 450mm complete all as specified and as directed

Material and labour for cutting of granite slab for fixing of under counter wash basin including rounded and grinding the stone with necessary arrangments complete all as specified and as directed

M&L for rendering 5mm thick in CM 1:3 on fair faces of Ceilings and finishing the surface even and fair complete all as specified and directed .

S & F in repairs Towel rail 600mm long of brass chromium plated fixed with and including CP brass screws and wooden/plastic cleats. (Minimum weight 190 gms)

Supply and fixed in repairs CP brass soap dish complete all as specified and as directed MAKE: CAT No F880011 of HINDWARE or equivalent model in JAQUAR/ PARRYWARE/CERA as approved by GE

S&F in repairs urinal with fixing accessories set of size 375 x 315 x 620 mm including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screw, waste pipe, inlet PVC connection, pointing around urinal back in cement with grating and union for discharge pipe complete all as specified and as directed. Make: Jaquar URS-WHT-13250 or equivalent as approved by GE

S&F in repairs CP bib tap 15mm bore fancy type with crutch or butterfly handle, screwed for iron pipe or for unions and fixed complete all as specified and directed.

S&F CP brass two way bib tap 15mm bore fancy type with crutch or butterfly handle with CP Health faucet fixing in pipe etc. complete screwed for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs CP angle cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply and fixed in repairs of 6mm thick frame less beveled rectangular wall mount plain mirror of any size and fixing of necessary Stainless steel finish solid mirror stud (12mmX19mmX2.5cm) complete all as specified and as directed. Make: Saint-gobain, Modi guard or equivalent model as approved by GE

Supply and fix stainless steel curtain rod of 25 mm bore fancy type complete all as specified and as directed

Supply and fix in repairs for stainless steel curtain rod brackets (decorative type) suitable for curtain rod of 25 mm dia, complete all as specified and as directed

S&F in repairs 4mm thick HPSC pre primed self designer texture non asbestos fibre cement building board fixed to false ceiling grid system of size 600 x 600mm frames etc complete all as specified and as directed.

Fixing only in repairs 4mm thick HPSC pre primed self designer texture non asbestos fibre cement building board fixed to false ceiling grid system of size 600 x 600mm frames etc complete all as specified and as directed.

S&F of 32 mm outer dia CPVC gate valves, with handle fixing for WPVC pipe and fixed complete all as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness including cover fillets etc complete all as specified and directed.

M&L for complete removal of existing finishes and applying two coats of cement based paint including preparation of surfaces etc all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash on wall surfaces

M&L for preparation of old treated surfaces of wall and applying two coats of white wash on wall surfaces

M&L for preparation of newly plasterd surfaces and applying two coats of cement based paint over a coat of primer including preparation of surfaces etc all as specified and as directed.

M & L preparation of old painted surfaces of wood and applying one coat of synthetic enamel paint on wood or wood based material over 10 cm width or girth.

M & L for preparation of newly plasterd wall surfaces of walls and applying two coats of distemper oil emulsion over 3 mm thick wall care putty and a coat of primer etc complete all as specified and as directed.

S&F of 4 dia Plain mild steel wire, galvanised class 3, in detached work such as for mosquito nets and fixing to straining bolts, hooks, eyes, etc. including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured) including making necessary anchorage arrangements in wall and complete all as specified.

M&L for Flush pointing to block in course or ashlar masonry or concrete block walling Raking out joints/ pointing to masonry or brick-work in single detached joints for flashing, etc.

Material and labour for brick work with fly ash bricks old size, straight or curved on plan exceeding 6.0 metre mean radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed

M&L for complete removal of existing treatment on wall surfaces and applying two coats of oil bound distemper over a coat of primer over a coat of 3mm thick birla care wall putty etc all as specified and as directed.

Taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit including removal of batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes all as specified.

Taking down old submain wiring of any size and type

Disconnecting and removing the MCB DBs/AC Box from any height ,stripping out the fitting for examine replacement of US spare parts, reassembling, refixing in original position including minor repairs for the smooth functioning and testing complete all as specified & directed by Engg in Charge

Material and labour for concealed point wiring complete with stranded copper conductor cables in concealed non-metallic PVC conduit 1.5 Sqmm (nominal area) PVC insulated unsheathed cable up to 1100 V grade FRLSH conforming to IS - 694 multistranded drawn including conduit with new sunk type pressed steel terminal boxes suitable for MODULAR switches including fixing/grouting sunken/ surface as per site requirement covered with suitable modular white cover plate for suitable size for mounting of MODULAR switches, regulators and drawing continuous earth wire with one run of 1.5 Sqmm (nominal area) PVC insulated unsheathed cable up to 1100 V grade FRLSH conforming to IS - 694 multistranded copper conductor as earth wire and connecting to common earth dolly and making good the disturbed wall surfaces to match with the existing surfaces complete all as specified and as directed for the following :- Note: Moduar cover plate with frame and modular metal flux box included in the rate quoted.

(a) One light/ Bell point controlled by one, one way switch 5 amps, SP

(b) One Ceiling Fan / exhaust fan point controlled by one, one way switch and regulator

(c) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board .

(d) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

Description as per item No. 123 here in before but using 2.5 Sqmm single core FRLSH copper conductor cable of multistranded PVC insulated unsheathed 1100 Volts grade for 3 Pin 15 Amps switch socket combination point on independent board including running of 2.5 Sq mm FRLSH copper conductor PVC insulated cable as earth continuity conductor.

Supply and fix in replacement of MODULAR switch 1 way 6 A, 1 Module capacity 230 volts complete all as specified and as directed.

Supply and fix MODULAR socket 5 pin 6 amps 2 MODULE, 230 Volts complete all as specified and directed.

Supply and fix in replacement of MODULAR socket 6 pin 6/16 amps 2 MODULE, 230 Volts complete all as specified and as directed.

Supply and fix Switch MODULAR 1 WAY 16 amps, 230 Volts complete all as specified and as directed.

S & F in replacement of Modular ceiling fan regulator 5 stepped type heavy duty suitable to work on 230 volts complete all as specified, 2 Module

S & F in replacement of ceiling rose three terminal surface bakelite type AC 50 Hz 230 volts of size 65 x 50 mm complete all as specified.

Supply and fix in replacement of wall mounted LED batten with extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver 1 x 20w, 230 volts, bipin holders, DIFFUSED TYPE connector block internally prewired etc with 2 Nos PVC round blocks for mounting arrangements including all accessories with new 3 core multi stranded copper conductor of size 23/0.193 from ceiling rose to fitting and including LED Tube 20W complete all as specified and as directed. Make: Havells Cat Part No LUMLINEPLUSNEOBS20WLED840SPCSSINDS, Philips Cat Part No BN170CLED20S-6500PSUL120 & Crompton Greaves cat Part No CCS-103-20-65-SL-DP-NWH

Supply and fix in replacement of LED security light luminaire fitting of 1x35 watts with deep drawn housing including all accessories with suitable 40 mm dia GI bracket 0.60 Mtr length fixed on wall with 50x6 mm flat iron, clamps, nuts and bolts complete all as sepcified and as directed. Make: Havells Cat Part No ENDURASUNDOWNSL35WLED765PASYBOPC, Philips Cat Part No BRP030PLED35CWSLRGRPSUSPD, Crompton Greaves cat Part No TRP-400-35-57-SL-LM-NSR

S&F sheet metal enclosure vertical type MCCB DB TPN 4Way double door with suitable rated bus bar 415 V suitable for and including MCCB TPN as incomer with suitable rated copper busbar with neutral link including provision for 125A MCCB 25KA TPN as incomer and SP/TP MCB's as outgoing and total number of modules equal to MCCB TPN + 12 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, complete all as specified and directed. Note: MCB SP/TPN will be meaured and paid seperately. Make: Indoasian cat part No 810530, Legrand cat Part NO 5077 50, Havells Cat Part No DHDLVDOBGSFE04

S&F in repair MCCB 100A 25KA FOR VTPN DBs Make: Indoasian Cat Part No 830052, Legrand Cat Part No 4200 55, Havells Cat Part No IHDA6OBF0100

S & F sheet metal enclosure MCB DB SPN 8 way with 200 amps rated bus bar 240 volts double door with magnetic locking system complete all as specified . Make: Havells Cat Part No DHDMSHCDOW08, Legrand Cat Part No 5076 11, Indoasian cat part No 810507

S & F sheet metal enclosure MCB DB SPN 12 way with 200 amps rated bus bar 240 volts double door with magnetic locking system complete all as specified . Make: Havells Cat Part No DHDMSHCDOW12, Legrand Cat Part No 5076 12, Indoasian cat part No 810508

S & F sheet metal enclosure MCB DB TPN 4 way with 200 amps rated bus bar 415 volts double door with magnetic locking system complete all as specified . Make Havells cat Part No DHDMTHPDOW04, Legrand Cat Part No 5077 80N, Indoasian Cat Part No 810516

S & F in replacement of MCB SP 6 to 32 Amps 240 volts for fixing on MCB/MCCB DB's all as specified. Make: Havells Cat Part No DHMZCSPF006-032, Indoasian Cat Part No 811008-15, Legrand Cat Part No 408587-95

S & F MCB SPN 40 Amps 240 volts for fixing on MCB DB's all as specified. Make: Havells Cat Part No DHMZCSNF040, Indoasian Cat Part No 811035, Legrand Cat Part No 4086 37

Supply & fix in replacement of connecting and testing MCB, Triple Pole Neutral (TPN) 63-100 Amps, 415 Volts of rupturing capactiy 10 KA, 'C' Series complete all as specified and as directed. Make Havells Cat Part No DHMZCTNF063, Indoasian Cat Part No 810098, Legrand Cat Part No 4086 83

Material and labour for earthing with galvanized mild steel earth plate electrode 60 centimetre x 60 centimetre x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 metres below ground level, the top edge of the earth plate at a depth of not less than 1.5 metres below ground level connected to galvanized iron earth wire of 4 mm dia by means of bolts, nuts and washers made out of GI / steel earth wire protected by GI light grade pipe 15 mm bore, 20mm dia light grade galvanised iron pipe with funnel wire mesh for watering and connecting to main switch board / control board all s shown in electrical plate of SSR Pt - I connected to earthing test point and including testing on completion complete all as specified and as directed. NOTE: The unit rate shall also include for excavation, earth work in hard/dense soil, plain cement concrete 1:3:6 type C1 by using 20 mm graded aggregate in pit, 50 mm thick reinforced cement concrete 1:2:4 type B1 using 20 mm graded aggregate cover duly reinforced with 8 mm dia TMT bars @ 100mm centre to centre both ways, galvanised iron funnel with watering pipe, wire mesh, complete.

Material and labour for sub main wiring with four runs of single core FRLS PVC multistranded stranded unsheathed copper conductor cable of size 10 square mm and drawing through concealed PVC conduit of 25mm dia with accessories in wall/roof along with one run of 10 square mm FRLS PVC insulated unsheathed multi stranded 1100 volts grade with copper conductor cable as earth continuity conductor connected to earth and earth dolly, connecting to main board including removing the existing wiring and making good the disturbed wall surfaces to match with the surroundings complete all as specified and directed. Note: 5 runs of 10 Square mm cable and 1 run of PVC conduit with accessories shall be measured as 1 unit of running metre.

Material and labour for sub main wiring with two runs of single core FRLS PVC multistranded stranded unsheathed copper conductor cable of size 6 square mm and drawing through concealed PVC conduit of 20mm dia with accessories in wall/roof along with one run of 6 square mm FRLS PVC insulated unsheathed multi stranded 1100 volts grade with copper conductor cable as earth continuity conductor connected to earth and earth dolly, connecting to main board including removing the existing wiring and making good the disturbed wall surfaces to match with the surroundings complete all as specified and directed. Note: 3 runs of 6 Square mm cable and 1 run of PVC conduit with accessories shall be measured as 1 unit of running metre.

Supply and fixing ceiling fans with blades down and accessories, 230V, 1200mm sweep with service value 5 star rated 6.000 BEE with BLDC motor all as specified and directed. Make: Havells/Bajaj/Orient

Supply and Fixing Steel body Exhaust fan of 300mm sweep of 1200 RPM,single phase 50 HZ AC Supply with blades, frames , louvers and connecting up with and including provision of PVC insulated copper flexible cord from ceiling rose to connection of exhaust fan complete all as specified.

Taking down ceiling fans 1200mm sweep, exhaust fan 200/450 mm sweep and wall mounted fan, remaining/cleaning of dust properly cleaning, greasing& overhualing of bearings including refixing and connecting up all as directed. Note : Replacement of defective/worn out parts will be measured & paid for separately

S & F in repair capacitor 2/2.5 mfd as directed (Make - Asian/Usha/Epcos of siemens)

S & F in repair ball bearing suitable for ceiling fans/exhaust fan/wall mounted fan.

S & F in repair twisted three core copper flexible cable of size 1.5 sqmm from connector to the ceiling rose complete all as directed

S & F in repair ‘U’ clamps complete with nut, bolts & split pins Heavy duty, suitable for existing ceiling fan.

S & F in repair M.S. rod for ceiling fans 5 ft long with ‘U’ clamp at one end other end with out nut bolts washers or screwed thread with check nuts & pin complete.

S & F in repair Nut of bolts washers for fan blades fixing of ceiling fan of any make/size/type as per site requirement ( 6 Nos for each set) complete,asuitable for existing ceiling fan.on site.

M & L for Rewinding of stator complete with super enameled copper wire of gauge/ weight of copper coil, quick varnishing oiling, greasing insulating materials including replacement of worn out parts like u/s cotter pin, nut, screw, check nuts and bolts as required including cleaning of body and testing of the size 1200 mm sweep ceiling fans, 200mm and 450mm exhaust fans of any make/model complete all as specifed and directed. Note :- Spare parts except mentioned above and rewinding to be replaced will be measured and paid seprately under respective items of schedule.

M & L spray painting of ceiling/exhaust fans/Wall nounted fan of any size with two coat of synthetic enamel paint complete all as directed.

Cutting of hole with the help of machine at wall or fabrication of aluminium frame with glass wall for fixing of exhaust fan including plastering and match with the existing surfaces complete and all as specified and directed.

M/S RADHIKA ENTERPRISES (BID ID -3420620)

POWER CONSTRUCTION COMPANY (BID ID -3420795)