PROVN OF STN SWIMMING POOL FOR WATERMANSHIP TRG AT HISAR MIL STATION

Amount

Lump sum price worked out by the contractor for "BUILDING WORKS" as listed in Schedule ‘A’ Part-I representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for "INTERNAL WATER SUPPLY " as listed in Schedule ‘A’ Part-II representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for "INTERNAL ELECTRIFICATION" as listed in Schedule ‘A’ Part-III representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for "ROAD, HARDSTANDING AND CULVERT etc." as listed in Schedule ‘A’ Part-IV representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for "SEWAGE DISPOSAL" as listed in Schedule ‘A’ Part-V representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for "AREA DRAINAGE " as listed in Schedule ‘A’ Part-VI representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for "FENCING, COMPOUND WALL & GATE" as listed in Schedule ‘A’ Part-VII representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Lump sum price worked out by the contractor for "DG SET, SUCTION SWEEPER MACHINE & FILTRATION PLANT" as listed in Schedule ‘A’ Part-VIII representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price of prepriced by the MES

Lump sum price worked out by the contractor for "EXTERNAL WATER SUPPLY " as listed in Schedule ‘A’ Part-IX representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price of prepriced by the MES

Lump sum price worked out by the contractor for "EXTERNAL ELECTRIFICATION" as listed in Schedule ‘A’ Part-X representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price of prepriced by the MES

Lump sum price worked out by the contractor for " SITE CLEARANCE, SITE DEVELOPMENT AND EARTH WORK " as listed in Schedule ‘A’ Part-XI representing percentage ( + or - denomination) derived under last column of this schedule above/below the lump sum price prepriced by the MES

Sch 'A' Part-XII (MISCELLANEOUS ITEMS) Notes: (i) This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under column 5 signifies this fact only. (ii) Excavation and earth work except for the items which categorically includes for same shall be measured and paid separately under SCH A PART-XI (SITE CLEARANCE, EXCAVATION & EARTH WORK schedule).

INTERNAL WATER SUPPLY M&L for 15mm bore two way bib taps, fancy type cast copper alloy chormium plated with crutch or butterfly handle, screwed down screwad for iron pipe or for brass ferrule and fixed complete all as specified and directed

M&L for 15mm bore, angle stop valve cast copper alloy fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed

S&F wall mixer of bathroom 3 in 1 system with provision for both hand & over head shower, with 115 mm long bend pipe, connecting legs & wall flange complete all as specified and directed Make -Jaquar (FUS-29218) or equivalent in as mentioned in Appx 'B' of Particular Specification

S&F in central hole basin mixer with popup waste system with 450 mm long braided hoses(15mm cartridge size) complete all as specified and directed Make -Jaquar (SOL-61698) or equivalent in as mentioned in Appx 'B' of Particular Specification

S&F Hand Shower (Health Faucet) (ABS Body) with 8mm Dia, 1.2 Meter Long Spirochrome flex tube & Wall Hook complete all as specified and directed Make;- Jaquar cat part no ALD-587

S&F CP Jet suitable for EWC with 01 meter pipe complete all as specified and directed

INTERNAL ELECTRIFICATION Supply and fixing round/square surface mounting 1x1 feet 20 watt minimum capacity LED panel in PDC housing and high translucent frosted plastic diffuser with 100 lumen per watt efficacy complete all as specified and directed

S & F for Highly efficient LED Bulbs, 9 watts complete all as specified and directed.

Supply & fix wall mounting fans 230 volts single phase oscillating 450 mm sweep suitable for wall mounting complete all as specified and directed.

Supply and fixing round/square surface mounting 2x2 feet 40 watt minimum capacity LED panel in PDC housing and high translucent frosted plastic diffuser with 100 lumen per watt efficacy complete all as specified and directed

S&F of modular Metal flux box 8 module complete all as specified and directed

ROAD, HARDSTANDING AND CULVERT Providing and applying 2.5mm thick road marking strips (retroreflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour ,T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.

S&F ABS speed breaker of size 500 x 400 x 50mm rubberized, tough, strong, weather resistant capable to with stand weight of the Vehicles comprises of segments of colour Black/Yellow and suitable fixing with zinc plated 12 x 120mm Nails. MAKE: OSCAR SAFETY SOLUTIONSCAT PART No. OS-793 or equivalent in as mentioned in Appx 'B' of Particular Specification

S&F Acrylic reflectors delineator (dual directional) having 100mm dia cube corner high intensity reflector (Red/Yellow/white) holded in strong plastic ABS body mounted over steel tube 65mm dia total height 700mm having flared/welded foot for firm grip to base acrylic reflector and ABS protected in a welded mesh cage. Note: All steel parts should be powder coated to make all weather resistant. MAKE: OSCAR SAFETY SOLUTIONS, CAT PART No. OS-797 or equivalent in as mentioned in Appx 'B' of Particular Specification

S&F Solar road delineator having 6 LEDs of colours Red/Yellow housed in aluminium/plastic body LEDs solar cells battery and light sensor well protected inside polycarbonate sheet devices protected with powder coated wire mesh cage system mounted over 47-65mm dia tube coated of length 700mm having sheet foot for firm grip to ground. MAKE: OSCAR SAFETY SOLUTIONS, CAT PART No. OS-812 or equivalent in as mentioned in Appx 'B' of Particular Specification

S&F dual directional reflective cat eye of impact resistant ABS plastic stud 100x100x20mm having ultra violet resistant colour White/Yellow/Red with reflective glasses beads of colour white/red/yellow and fixing with zinc plated 12x120mm nails with hurting for road grip on the road by hammering complete all as specified and directed by Engr-in-Charge. MAKE: OSCAR SAFETY SOLUTIONS, CAT PART No. OS-781 or equivalent in as mentioned in Appx 'B' of Particular Specification

S&F polycarbonate convex road safety mirror of size 600mm dia duly plastic framed back covered and provided with holding clamp arrangement having wide field of vision, exterior weather proof, bright reflection, anti glare and easy to maintain suitable for installing on blind curves over the wall or pole etc including round stand post 50mm dia made out of 1.65mm thick steel CRC sheet of total length 2000mm having hold fast at the bottom and top end closed with MSD sheet painted white with synthetic enamel paint over a red oxide metal primer complete all as specified and directed by Engr-in-Charge. MAKE: OSCAR SAFETY SOLUTIONS, CAT PART No. OS-791 or equivalent in as mentioned in Appx 'B' of Particular Specification

DG SET, SUCTION SWEEPER MACHINE & FILTRATION PLANT Supply, installation, commissioning and testing of diesel engine driven, water cooled, electrical start silent Generating Set 62.5KVA capacity, liquid cooled, turbo charged with after cooler, developing 80.1hp @ 1500 RPM, 4 valve per cylinder, electric start, compressor ignition, 4 stroke engine designed to run continuously at 1500 RPM confirming to time rating ISO-3046/BS5514 standard with an overload capacity of 10% for one hour in every 12 hrs of operation, diesel forms to present CPCB norms complete including common base plate, floor mounted , factory assembled complete fitted in and including acoustic enclosure (sound proof canopy of suitable capacity or size) alongwith standard manual panel approved by National Physical laboratory with inbuilt standard panel, in built fuel tank suitable capacity for 12 hrs running at full load continuous running, with fuel lines of heavy duty MS pipe duly painted, including PCC foundation / platform for generating set as per manufacture's instructions / conforming with drawing complete as specified and comprising with and including the following :- a) Flywheel with starter ring for generating set. b) Air filter. c) Lub oil cooler assembly with accessories. d) Exhaust air manifold.

e) Expansion bellow. f) Fuel filter. g) Lube oil filter. h) Exhaust gas turbo charger with after cooler. i) Radiator with pusher type fan, with fan guard, coolant pump. j) 12 V electrical starting system with starter motor and battery charging alternator. k) In-line monoblock fuel injection pump with electronic governing & Isochronous capability. l) Bore x stroke - As per Manufacturer design n) Engine mounting supports. o) Engine control panel - microprocessor based controller model. p) Engine safeties, alarms and trips. q) K cool super plus corrosion inhibitor coolant for cooling. r) Engine operator/ maintenance & spare parts CD. s) Engine warranty certificate and test certificate.

(A) Alternator Alternator rated at 62.5KVA, 415 volts, 3 phase, 4 wire, 0.8 p.f. (lag), 50 Hz, 1500 RPM, in accordance with IS 4722 as per following specifications : i) Type : Salient poles, single bearing, Brushless type, suitable for direct coupling engine. ii) Rating : Guaranteed to deliver required output at the ambient temperature conditions of Hisar. Suitable for an over load of 10 % for 1 hour in every 12 hour of operation. iii) Voltage regulation : Provided with fast response thyristor type electronic automatic voltage regulator, which holds output voltage within desired limits.(+/-1%). iv) Excitation : Self excited self regulated. v) Alternator loading : Suitable for taking rated load immediately after machine reaches rated voltage and speed. vi) Equipped with AREP ( Auxiliary regulation Exiting Principle) winding to give performance equivalent to PMG as standard scope of supply. vii) Vibration: Suitable for direct coupling with Engine and mounted on common fabricated sheet metal base frame. viii) Enclosure: Screen protected drip proof enclosure with IP – 23 degree of protection. ix) Cooling: Air Cooled type with radial fan mounted on Rotor. x) Winding and Insulation: Insulation class H as defined in IS – 4722.

(B) Diesel Engine Adequate capacity of diesel Engine of suitable BHP to give out put of 62.5 KVA by alternator , liquid cooled to drive independently above alternator and after considering duration as per site conditions generating and reducing power consumed by accessories. Directly coupled through flexible coupling multi-cylinder , multi stroke direct injection , cold starting 1500 RPM as per with an overload capacity of 10% for one hour in any 12 hours continuous running complete with standard accessories all as specified and required for safe handling and operation. Make– of KIRLOSAR (KOEL Green) or Equivalent model of CUMMINS / GREVES COTTON / ASHOK LEYLAND Note : Paid voucher for the complete DG set shall be from the same OEM only. (C) ESSENTIAL ACCESSORIES Following set of essential accessories are supplied with each

DG set:- i) One No. MS Base Frame suitable for mounting of the offered engine and alternator. ii) One No. fuel tank of standard capacity suitable for 12 Hrs running complete fuel gauge, inlet/outlet connections, drains plug, etc. iii) 12 volt 88 Ah/suitable capacity Volts DC Battery of suitable capacity with leads. iv) 1 Set of AVM Pads fitted in Base Frame. v) All above accessories are housed in acoustic enclosure(D) CONTROL PANEL The Control Panel body shall be fabricated out of 16 SWG MS sheet. Panel shall be suitable for inside Canopy mounting, indoor installation, Copper Control cable of suitable size and required length shall be used. Cables are ferruled for proper maintenance/checking/wiring of panel. Detachable cable gland plates are provided. The panel shall be equipped as follows: i) One No. Moulded Case Circuit Breaker of suitable capacity. ii) Aluminium Bus Bars of suitable capacity provided with termination. iii) 3 Nos. Current Transformers of suitable ratio. iv) One set of instrument MCB’S. (E) Civil Works. : - All civil works related to foundation, installation of panel and equipments including making good of existing structure if disturbed during installation and commissioning of Gen Set.

(e) Supply and fix Acoustic Enclosure factory made floor mounted factory built modular in construction for Engine and Alternator consisting Acoustic panels of tubular / angular in section fabricated out of 16 SWG cold rolled steel sheet packed with 1.5 mm PVC film with 25mm thick PU foam of appropriate density so as to reduce noise level 75 db measured from a distance of 1 metre from enclosure as per the norms of pollution control board suitable for 62.5 KVA Diesel Generating set approved by OEM Make of Acoustic enclosure shall be as per OEM's Recommendation. Note: (a) Cost of necessary cabling from control panel to DG set is included in this item. (b) Cost of servicing and maintenance as prescribed by OEM for 2 years from operation of DG set is included in this item.

Supply install test and commissioning of Trolley mounted suction sweeper suitable for swimming pool with self priming electric driven pump set suitable for cleaning swimming pool capacity 2 HP, 3 Phase complete with PVC braided 40mm dia vacuum hose pipe of length minimum 30 Mt, 900 mm size mettalic vacuum head, flexible copper cable from Main, PVC floats, wire rope and all connected accessories complete as following items:- (i) 18 inch long Nylon brush -02 Nos (ii) Float complete to support the hose, clips for connection - 10 Nos (iii) Telescopic pole 4.8 Mtr long with extendible up 9 Mtr made of aluminium tubing complete:- 02 Nos (iv) Supply and fix anodised Extruded Stainless Steel Vacuum Head - 900 mm Stainless steel grade -304 fixed with clip type connection 25 mm / 50 mm dia maintenance kit complete all as specified and directed.-02 Nos (v) Deep bag skimmer clip type along with handle 5 meter long made of aluminium- 02 Nos (vi) Curved brush clip type - 02 Nos (vii) Algae brush clip type - 02 Nos (viii) Nylon rop 20 mm da -200 meter (xi) Supply only manual Test Kit for PH & Residual chlorine - 01 Nos (x) Supply only electronic Test Kit for PH & Residual chlorine -01 Nos (xi) Life bouy along with hook amd rop - 02 Nos (xii) Leaf rack made out of aluminium frame all as per sample - 02 Nos

Supply installation and testing or vertical floor mounted self supporting totally anticorrosive bobbin wound FRP pressure sand filter tube glass shelf with thickness as specified by the manufacturer dished ends complete with UPVC face piping ABS plastic with manual stage dump drain valve water drain valve pressure gauge, sample cock, air vent and all accessories with initial charge of filter media (silica quartz sand) and gravel and with vertical supports with piping and suitable foundation as required at site for swimming pool of size 50 x 21 Mtr suitable for 8 Hrs turn over period having following specification. (a) flow rate 125 m3 / Hrs(each). (b) Vessel dia minimum 2000mmm (c) Filtration velocity 40 m3/Hr/m2. (d) Working pressure 2.5 kg/Cm2 all as per DIN2501 standard alongwith all type of valves back wash system all as directed and specified by Engineering-in-Charge. Note :- Drawing for filter shall be approved by GE before placement of order.

Supply, install, test and commissioning of Self Priming water circulation pump, Horizontal split casing end suction pump 415 V, 50 Hz, 1450 RPM suitable for pressure sand filter designed discharge capacity 125 m3 / hour @ 15 Mtr head having pump efficiency 65-75%, and suitable for filtration plant as per Sl No 1 for ensuring turnover period 7.0 to 8.0 hour with suitable capacity prime mover motor IE2 TEFC Two Poles, Continuous Operation F class insulation, protection IP-55, Operating voltage 380V-440 / 3 phase, 50HZ . Pump with pre filter in Cast iron with matching connection size Impeller & Motor shaft in Stainless steel AISI 304 with Mechanical seal in Graphite/Ceramic. The pump shall be of cast iron body, bronze impeller, with mechanical seals, TEFC squirrel cage IE-2 induction motor, M.S. Fabricated base plate, mounting channel frame, accessories and fitting i.e. pressure gauges, Air release valve, drains, coupling, coupling guard, PCC foundation, vibration isolation arrangement complete all as specified in the particular specification. Note: Cost of PCC foundation is deemed to be including in the unit rate.

Supply, install, test and commissioning of Air Blower system unit including all type of accessories with suitable 3 Ph motor IE-2 rated , ISI marked required for sand filtration unit back wash process of suitable capacity but not less than 200 Cum /Hr , or as recommended by OEM for swimming pool all as directed and specified by Engineer-in-Charge.

Supply, Installation, Testing and Commissioning of UV system consisting of following:- UV system flow rate: 25.00 m³/h, dose: 11 MJ/cm², light power : 75W UVC equipment made using the latest technological design to ensure effective water flow through the unit, driving better UV light performance designed to bear pressure up to 4 bars, power consumption low, the whole of the electrical system protected so that water cannot enter and thermal element to prevent power surges, the UVC units distributed with two male threads of 1.5''/50mm, the product easy to install, each unit distributed with stainless steel anchoring fixtures for vertical or horizontal fastening and complete all as directed.

Supply, installation, testing and commissioning of Automatic electronic Membrane Dosing Pumps for chlorination , PH correction complete with chemical storage tank, Agitators and with following specifications:- (i) Dosing pumps:- Design, supply, installation, testing and commissioning automatic sensor based dosing pump sets including LCD screen on/off or proportional operation mode 0-14LPH 1000-1400 MV, PH, RX (ORP) electrode inlet (10 tera OHM), including electrode screen resolution 0.01PH ( + ) 1 mv ph/ Rx 10 litre /hour -5 bar, IP-65 protection anti acid plastic casing, control panel protection weather proof and resisting UV rays, standard power supply 230V AC 50 HZ single phase with sensor. PH sensor kit including PH sensor (ii) Chemical storage tanks:- Semi transparent polyethylene tank with external scale so that levels can be checked easily capacity of tank 500Lts. (iii) Agitators:- Agitators for easy installation in the tanks, provided with steering grip in Bakelite, rod and propeller arms in PVC, length of stirring rod 900mm. ( Note:- 04 Nos dosing pump will be used for the chlorination of water and 01 No for maintaining PH level.)

Supply, installation, commissioning and testing of LT panel board Kiosk type ,LT (415 Volts, 50 Hz , 3-phase, 4 wire supply) CPRI type tested, factory assembled ,outdoor type, dust, weather and vermin proof (Protection Class IP-54) made of 3.15 mm (for external) and 2 mm (for internal) thick CRCA sheet with both side (front and back) hinged , double door opening for external, rubber lining, locking arrangement, duly powder coated externaly & internally with grey shade (RAL-7032) as per seven tank process complete mounted on angle iron 40mm x 40mm x 5 mm legs 45 cm high above GL and 15 cm embedded in ground with and including blocks of PCC 1:2:4 type C1 of block size 30x30x30 cm comprising of the following.

Supply and install flow adjustable ABS heavy duty foot inlet nozzles having flow rate of 5 meter cube per hr fitted vertically on the UPVC pipe of size 63 mm to 200mm bore as required on site along with connection arrangement such as Stainless steel screws, tail piece , T section, reducers on the bottom for the swimming pool and diving pool for filling the swimming pool and diving pool complete. Note: All the nozzles shall be fixed as per swimming pool and driving pool water supply drawing or as per manufacturer recommendation.

Supply and lay/ fixing in floor / in trench / on wall / concealed UPVC pressure pipes of following sizes Class - 5 (10kg/cm2) with plain socket suitable for and including solvent cement jointing conforming to IS: 4985/2000 complete with fitting and specials such as bends, tees, unions, reducers, flanges and plugs etc complete. Note : The pipes and fittings shall be tested to pressure of 10 Kg/Sqcm.

63 mm bore

150 mm / 160 mm bore as per site requirement

200 mm bore

250 mm bore

300 mm bore

Supply and fixing water type cast iron butterfly valves of the following sizes tested to 10 kg/sq.cm pressure (including flanges & All other accessories) complete all as specified and directed. Make :- Zoloto/ Leader/ Venus

63 mm bore

100 mm bore

150 mm /160 mm bore

200 mm bore

250 mm bore

300 mm /315 mm bore as per site requirement

Supply and fixing of 150 mm bore CI dual plate Check Valve ( Non return valve) (PN 1.6) IS5312 complete with matching flanges rubber insertion sheet, nuts, bolts and washer etc complete. Make :- Zoloto/ Leader/ Venus

Supply and fixing of 200 mm bore CI foot valve (IS 4038) complete with matching flanges rubber insertion sheet, nuts, bolts and washer etc complete. Make :- Zoloto/ Leader/ Venus

Supply and fixing of following sizes of heavy duty PVC puddle flanges of suitable length and made of (uPVC pipe 10kg/cm2) complete with matching flanges including jointing material all as specified and directed. Make:- Supreme/ Astral/ Finolex/ Prince Note :- These flanges shall be suitably placed between steel reinforcement as per standard Engineering practice.

150 mm / 160 mm bore as per site requirement

200 mm bore

250 mm bore

300 mm / 315 mm bore as per site requirement

Supply & fixing of ABS white plastic suction port/ vacuum nozzle suitable for and including solvent cement connection along with Stainless steel drain grating plate made out of 304 quality S S plates of size 500mm x 500mm with suitable supporting frame and of following sizes and having holes of required size for drainout chamber.

Supply, installation, testing and commissioning suction, delivery and header lines of following sizes including cutting, bendings, welding and fabrication work, making provision for different pipe connection in required length as per ground requirement and drawing approved by Engineer-in-Charge. A. Pump Suction lines of 200 mm dia made of MS "c" class Epoxy Coated for 5 Nos. pumps. Suction line will be layed from Balancing tank to the pumps. Y strainer is included in the quoted job. Nothing will be paid extra. B. Pump Delivery lines 150 mm dia made of MS "c" class Epoxy Coated for 5 Nos. pumps. Delivery lines will be laid from pump to delivery header. 150 mm dia connection for Pump delivery, 5 Nos. of 150 mm dia connection to feed the filters. Delivery Header of size 350 mm Dia M.S. "c" class Epoxy Coated Suction and including cutting, welding and making provision for different pipe connection including following arrangements C . Commen delivery header for pumps of size 350 mm Dia M.S. "c" class Epoxy Coated. Header will connect line of delivery line of pump and suction lines of sand filters.

Supply, installation, testing and commissioning of MS Structure work made out of Angle, Fasteners, Tie Rods, flat for pipe support and pump footing complete all as specified and directed. Note : All MS work to be painted with 02 coats of synthetic enamel paint over a coat of red oxide primer.

Supply and install Over flow grating 300 mm x 300 mm wide shall be provided as shown in drawing with slope 1:200, towards shall be provided as shown in drawing with slope 1:200, towards balancing tank including Gratings and support profiles made in white UV stabilized PP of size wide complete all as specified and directed. Make : Ion Exchange/ Thermax / UV rich

Supply install test and commissioning of Pool under water integral LED model 15 Watt minimum, wall mounted type working on 12 V DC, IP68 complete with built-in driver, including push in connector in 4 pole including flexible conduit and all fixing arrangement in swimming pool wall to accommodate pool light complete all as specified and directed.

Supply install test and commissioning of Junction box of suitable size round/square type with water proof covering made of ABS plastic material complete all as specified and directed.

Supply and lay in conduit, under floor, on wall, of 3 core 2.5 sq.mm. PVC insulated FRLSH copper conductor 1100 Grade un-amoured cable Wiring from under water lights to distribution panel all as directed and specified by Engineer-in-Charge.

Supply, installation, testing and commissioning of heavy duty PVC conduit 20 mm PVC, ISI marked conduits complete with accessories such as bends, junction boxes, pull boxes etc. complete all as specified and directed.

Supply, installation, testing and commissioning of water proof IP-68 distribution box for under water lights drivers and MCB complete all as specified and directed.

Supply, laying, testing and commissioning of following size heavy PVC insulated sheathed copper conductor 1100 V grade enamoured cable with required size of sleeves complete as required.

10 Sqmm x 4 core

6 Sqmm x 4 core

4 Sqmm x 2 core

2.5 Sqmm x 1 core

4 Sqmm x 1 core

Supply, installation, testing and commissioning of GI perforated Cable Tray 200 mm wide all as specified and directed.

Supply, installation, testing and commissioning of heavy duty PVC conduit 25 mm PVC, ISI marked conduits complete with accessories such as bends, junction boxes, pull boxes etc.

Supply only TCCA 90 swimming pool disinfection in granular form having effective chlorine above 90 % to be supply in 50 kg plastic container complete all as specified and directed.

Supply, Installation, Testing and Commissioning of Stainless Steel 304 ladders, width 500mm, handrails dia 42 mm stainless steel, non-slip steps provided with anchoring Socket.

3 Step Standard Ladder

4 Step Standard Ladder

5 Step Standard Ladder

Supply, Installation, Testing and Commissioning of Hand Rail, 1.2 meter long in Stainless Steel 304 all as directed and specified by Engineer-in-Charge.

EXTERNAL WATER SUPPLY Supply, laying and testing Ductile Iron pressure pipe 150 mm bore with spigot and socket ends centrifugally cast, Class K-7, conforming to IS: 8329/2000 - blast furnace slag cement with Portland cement properties suitable for push-on-jointing (Rubber tyton joints) with inside cement mortar lining with internal metallic zinc coating and external Black Bitumen coating complete all as specified and as directed by Engr-in-charge. Note:- Cost of joints including jointing material shall be deemed included in unit rate quoted by the tenderer. Earth work & DI specials/ fittings shall be measured & paid separately.

Supply and fixing, testing sluice valve cast 300mm dia iron ISI marked with flanged ends drilled with iron wheels head shuts and open direction cast on it class PN-1.6 conforming to IS : 14846-2000 including rubber insulation packing rings , jointing material nuts ,bolts & washers of suitable size etc on existing pipe including testing on completion all as specified

Brick masonry valve pit of size 105x105x110 cm (internal dimension of chamber incl plastering internal and flash pointing external as the work proceeds in same mortar complete with MS sheet cover handle, packing arrangement, earth worth in any type of soil incl removal to n.exc 50 mtr and paint with 2 coats of synthetic enamelled paint over a coat of red oxide primer to steel surfaces complete all as specified.

All as per Item No 60 here in before but of size 60x60x60 cm complete all as specified.

M&L for provision of thrust block of size 1.00 x 1.00 x 1.00 mtr in cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate including use and waste of necesssary formwork etc complete all as specified and directed.

EXTERNAL ELECTRIFICATION Supply, testing and commissioning of 11kV Outdoor type 100 KVA Package Sub-Station consisting of 11/0.433KV, Oil type transformer, HT panel, LT panel AND APFC panel inside GI sheet steel enclosure with all interconnections, fully type tested as per the IEC-1330 and CPRI complete in all respect including foundation as manufacturers specification consisting of following items & as per detailed technical specifications:

Outer Enclosure:- Outdoor type enclosure having modular construction of 2mm Galvanised Sheet Steel. The Enclosure shall have IP54 degree of protection for HT & LT switchgear compartment & IP23 degree of protection for Transformer compartment. The enclosure exterior shall be painted with polyurathene paint (Seimen Gray Colour). Each compartment will be provided with the door and pad locking arrangement. The Compartment illumination lamp with door operated switch shall be provided for each compartment. Interconnection Between HT switchgear & Transformer using aluminium Busbar & Interconnection between Transformer & LT switchgear using Busbars. All metallic components shall be earthed to a common earthing point. Dimensions shall be manufactures instruction and as per the final decision at Site for components to be included in enclosure. HT Panel: 11KV, 630A, indoor type 26.3 kA load break switch (LBS) with fuse trip, earth switch, dynamic mimic arrangement, 230 v ac shunt trip coil and 2NO+2NC aux. contacts for transformer protection incuding 11Kv HTHRC Fuses Rating: 50A

Transformer: Supply, installing, testing and commissioning indoor type, step down transformer, 11 KV/433 Volts AC 3 phase 50 Hz, 100 KVA capacity, core type, double copper wound, oil immersed naturally cooled, Oil Natural- Air Natural, DYN-11 with Neutral brought out on secondary side (LV side) and having tapings at +5.0%, +2.5%, 0%, -2.5%, -5.0%, -7.5% & -10.0% on HV side to be changed by means of hand operated off load tap changer gear with all standard fittings & accessories (as per IS-1180:2014 EEL-2 LT Section 433V LT Indoor panel with Aluminium Busbars , Fabrication using 2 MM CRCA sheet steel , Ingress protection IP4X , solidilly earthed at substation complete with internal wiring, indication lamps etc consisting of following switchgear Incomer :-(i) MCCB 4 pole, 50 Hz AC, 200 Amp 36 KA, Thermal Magnetic release,thermal adjustable type (Ics=100%Icu).-01 No. Outgoing- (i) MCCB 4 pole, 50 Hz AC grade,160 amps, 25 KA thermal adjustable fixed magnetic ( Ics=100%Icu). -02 No.

(ii) MCB 415 Volt 32 Amps 16KA, 4 pole-04 Nos. (iii) MCB SPN 230 V, 32 Amps-04 Nos. (iv) On load change over switch 200 Amps, 415 volt, 4 pole-01 Nos (v) Din type astronomical digital time switch, 16Amp with 02 change over for street light. (vi) Power contactor with control relay of capacity 16 Amps for street light-02 Nos APFC Section SITC of factory built floor mounted auto-manual APFC panel of 50 KVAR capacity with APFC relay 5 stage with heavy duty MPP capacitor bank 50KVAR (Capcitor size 15x2, 10x1, 05x2 Nos), with 7% detuned harmonics filter reactor. ) with thyrister control module and MCCB TP of 16 KA of 1.5 time of rating current of capacitor suitable for each control.The panel shall be made of 2mm thick CRCA Sheet including powder coated painting provided with exhaust fans (with thermostat) and grills for proper ventilation, interconnections with suitable size conductor cables & lugs and accommodating the following switchgears & accessories:

(i) Compact modular bolted design, removable side and back panels with option of top and bottom cable entry (ii) Capacitor installed in removable assemblies for ease of operation and maintenance (iii) Incoming of APFC panel of MCCB TPN 100 Amps, 16 KA breaking capacity with high electrolytic grade Aluminium bus bar iof suitable rating. (iv) 50KVAR (Capcitor size 15x2, 10x1, 05x2 Nos), with thyrister control module and MCCB TP of 16 KA of 1.5 time of rating current of each capacitor suitable for each control . ( each capacitor bank equipped with discharge resister) & 7% detuned harmonics filter reactor. (v) High performance microprocessor based 3 phase APFC relay 5 stage with Auto/Manual Option. (vi) In built 3 phase power analyzer , Amp meter, volt meter and PF meter. (vii) Capacitor duty thyrister control modules with high thermal current carrying capacity and early make contacts to reduce inrush current for enhancing life of capacitors (viii) Induced air system provided with axial flow fan/ centrifugal fan.

S&F PVC junction box suitable for street light of size not less than 310mm x 285mm x 180mm, made out of polycarbonate having front side openable shutter duly provided with locking arrangement and provided with aluminium bus bar of rating upto 32 Amp alongwith 01 No MCB 6 Amp SPN and provision of 02 Nos cable entries, fixed on street light pole with proper size MS clamp with nut & bolt and connected assessories complete all as specified and directed.

Excavation by trenchless technology boring of holes under road pavement ,hard standing by trenchless technology using ultra sound, technique and necessary machineries including HDPE pipe of 150mm dia suitable for 0.4 Mpa working pressure.

Sh. Raj Kumar Malik Contractor (BID ID -3123362)

M/s godara infratech and power industries (BID ID -3123825)

G and G Infratech Private Limited (BID ID -3123555)