UDZRM/SECY/ 16/2024-25

Amount

Supply Item

Supply of Brick to Department

Deduction of brick for collect fro department

Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m a) In ground floor including roof.

Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars (a) In ground floor including roof.

Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed.

Supplying & laying Polythene sheet (150 gm/Sq. m ) over damp proof coarse or below flooring or roof tarracing or in foundation or foundation trenches.

Cement Concrete with 40 mm down ballast excluding shuttering. (1:3:6 proportion.)( Pakur Vr.)

Brick work with 1st class bricks in cement mortar (6:1) b) In Superstructure

Ordinary Cement Concrete (mix 1:1.5:3) with graded stone chips 20mm. nominal sizes excluding shuttering and reinforcement (if any) as per relavent IS Code . (i) Pakur Vr.

Hire and labour charges for shuttering with centering and necessary staging upto 4m using approved stout props and thick hardwood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels, curved or straight including fitting fixing and striking out after complete of works(upto roof of groun floor). f) 25mm to 30mm shuttering without staging in foundation.

Reinforcement for reinforced concrete work in all sorts of structure including distributors, stirrups binder etc. including supply of rods initial straightening and removal of loose rust ( if any) necessary cutting to requisite length hooking and bending to correct shape placing in proper position every intersection complete as per drawing and direction. i) gr. Floor For works in foundation, basement, roof of ground floor/upto 4m. i) Tor Steel II) Other than Sail/TATA/RINL

Plaster (to wall, floor, ceiling etc.)with sand and cement mortar including rounding off corners and chamfering corners as directed and racking out including, throating, nosing and drip coarse, scafolding/ staging where necessary(Ground Floor) (Excluding cost of chipping over concrete surface.) (i)(b)20mm th. Cement plaster(1:6)

Plaster (to wall, floor, ceiling etc.)with sand and cement mortar including rounding off corners and chamfering corners as directed and racking out including, throating, nosing and drip coarse, scafolding/ staging where necessary(Ground Floor) (Excluding cost of chipping over concrete surface.) (i)(c)15mm th. Cement plaster(1:6)

Plaster (to wall, floor, ceiling etc.)with sand and cement mortar including rounding off corners and chamfering corners as directed and racking out including, throating, nosing and drip coarse, scafolding/ staging where necessary(Ground Floor) (Excluding cost of chipping over concrete surface.) (ii)(b)15mm th. Cement plaster(1:4)

Plaster (to wall, floor, ceiling etc.)with sand and cement mortar including rounding off corners and chamfering corners as directed and racking out including, throating, nosing and drip coarse, scafolding/ staging where necessary(Ground Floor) (Excluding cost of chipping over concrete surface.) (ii)(c)10mm th. Cement plaster(1:4)

Neat cement punning 1.5mm thick in wall dado window silt, floor, drqins etc. using cement @ 0.152M3/M2

Applying decorative Cement base paint ofapproved quantity after scraping the surface throughly as necessary as on plastered surfasce, ruled or concrete surface. Two coats

Applying exterior grade acrylic Primer of approved quality and brand on plastered or concrete surface old or new surface to receive decorative textured (matt finish) or smooth finish / Acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacture's specification and as per direction of EIC. (b) two coats

Protective and decorative textured exterior high class matt finish paint of approved quality, composed of special Tharmoplastic Resin containing fine crystaline additives derived from granite as per manufacture's specification and as per direction of EIC to be applied over acrylic primer as required.( Two Coats )

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (B) Wall With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (a) Area of each tile upto 0.09 Sq.m (i) Coloured decorative

18mm to 22mm thick kota stone slab set in 20mm thick (avg) cement morter (1:4) in floor, stair & lobby including pointing in cement slurry with pigment matching the stone shade, including grinding & polishing as per direction of Engineer in charge to match with the existing work. (Slurry for bedding @ 4.4 kg/Sq.M and pointing @ 2.0 kg/Sq.M.

Extra cost of labour for grinding Kota stone floor in treads and riser of steps.

Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete. (

Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to I.S. 1038-1975 and manufactured from rolled steel section conforming to I.S7452-1974 with non friction projecting type box type type hinges. b) Openable steel window with side hung shutters.

c) (viii)Extra over above item for- M.S. Integretd grill as approved design integreted with steel window or ventilator.

Easing and oiling, cleaning rolling shutters excluding repair to inside lock

L abour for taking out rolling shutter (only shutter portion) dismantling by parts for repair or (replacement of damaged parts only), rehanging and refitting the same in position after necessary repairs (excluding the cost of supply of new parts).

Renewing seam pipe for rolling shutter as per existing size and shape fitting, fixing complete.

Renewing side split pin for seam pipe for rolling shutter.

Oiling and greasing of rolling shutter and repair to in side lock.

Renewing profile of rolling shutter including fitting fixing complete as per existing size and shape.

Renewing spring of rolling shutter as per existing size and shape including fitting fixing complete.

a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surface by sand papering etc. i) on steel

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (a) On timber or plastered surface : (iv) Two coats (with any shade except white) (b) On steel or other metal surface :(iv) Two coats (with any shade except white)

Supplying fitting fixing in position fibre glass panes of approved quality with resin. Nail, clip etc. as IS: 12866-1989. in all floor internal wall) (e) 4 mm thick.

Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all ecessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete. ii) 110 dia

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (b) For Concealed Work i) 15 mm

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (b) For Concealed Work ii) 20 mm

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (b) For Concealed Work iii) 25 mm

Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint (iii) 630 mm X 450 mm size

Supplying, fitting and fixing bib cock or stop cock. (a) (ii) Chromium plated Bib Cock long body with wall flange with aerator (Equivalent to Code No. 512 & Model - Tropical / Sumthing Special of ESSCO or similar brand)

(d) (i) Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand).

Supplying, fitting and fixing pillar cock of approved make. a) (ii) CP Pillar Cock Super Deluxe with Aerator - 15 mm. (Equivalent to Code No. 508 & Model No. Tropical / Sumthing Special of ESSCO or similar brand).

Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps. (iv) 1050 mm long

Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing) i) 580 mm X 440 mm

Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc.

Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. i) 635 mm X 395 mm X 420 mm

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 (A) (i) Single Socketed 3 Meter Length

Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete. iv) Bestolite (solid type) white

Supplying, fitting & fixing approved brand P.V.C. CONNECTOR white flexible, with bold end coupling with heavy brass CP nut, 15 mm dia.

M/S B PAUL AND COMPANY (BID ID -5684244)

MD. IBRAHIM (BID ID -5684228)